ADSP-21060KS-160 - 40MHz 32-Bit SHARC DSP | Analog Devices
MPN: ADSP-21060KS-160 ✓ 啟用中ADSP-21060KS-160 概覽
A digital signal processor, or DSP, is a semiconductor optimized to execute mathematical operations on streams of sampled data with predictable throughput. The ADSP-2106x hierarchy includes the SHARC DSP core, 32-bit signal processing microcomputer, and embedded processor products. Its architecture separates instruction access and multiple data-transfer paths, allowing computational engines to access operands while other transfers are in progress.
The ADSP-21060KS-160 provides 32-bit IEEE floating-point computation through an arithmetic logic unit, multiplier, and shifter. It reaches 120 MFLOPS at a 40 MHz clock and contains 4 Mbits of dual-ported on-chip SRAM, divided into two 2-Mbit blocks according to the ADSP-21060 family datasheet. These resources support high-throughput filtering, FFT, spectral analysis, modulation, and other fixed- or floating-point processing workloads.
The 5 V operating supply and 240-lead exposed-pad package place substantial routing and thermal demands on the PCB design. Its 32-bit data path supports high-bandwidth signal processing, while the external memory interface allows designs to extend storage beyond the internal SRAM. The exposed pad provides the primary thermal conduction path, so copper coverage and via arrays strongly influence junction-temperature performance.
Typical uses include communication-system front ends, industrial vibration analysis, medical signal processing, audio equipment, imaging pipelines, and control systems. The device is most appropriate when deterministic real-time filtering or waveform analysis is required and the application already uses the ADSP-2106x software and peripheral ecosystem.
PCB design should preserve short, controlled clock and data routes, follow the exposed-pad land pattern, and provide suitable decoupling close to the supply pins. Firmware, memory-map, timing, and peripheral configurations must also be reviewed because functionally similar ADSP-2106x processors can differ in clock rate, temperature grade, or available resources even when they use the same mechanical package.
This product record combines manufacturer specifications, package information, commercial availability, and pin-compatible family references with practical guidance for DSP board design, thermal management, and component selection.
直接替換替代品,適用於 ADSP-21060KS-160 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
ADSP-21060KSZ-160
✅ 直接替換📋 參考替代品(不在目錄中)
ADSP-21060LKS-160
✅ 直接替換📋 參考替代品(不在目錄中)
ADSP-21060LKSZ-160
✅ 直接替換📋 參考替代品(不在目錄中)
ADSP-21062KS-133
✅ 直接替換📋 參考替代品(不在目錄中)
ADSP-21061KS-160
✅ 直接替換📋 參考替代品(不在目錄中)
ADSP-21060KS-160 規格
| Processor Type | 32-bit SHARC floating-point digital signal processor |
| Architecture | Super Harvard Architecture with four independent buses |
| Core Clock | 40 MHz |
| Peak Floating-Point Performance | 120 MFLOPS |
| Word Width | 32 bit |
| 資料匯流排寬度 | 32 bit |
| 供應電壓 | 5 V |
| On-Chip SRAM | 4 Mbits, organized as two 2-Mbit blocks |
| Arithmetic Units | Multiplier, ALU, and shifter |
| 封裝 | 240-MQFP-EP (32 x 32 mm) |
| 腳位數 | 240 pins |
| 安裝類型 | Surface Mount |
| Exposed Pad | Yes |
| AEC-Q100 Qualification | Not applicable |
ADSP-21060KS-160 240-mqfp-ep (32 x 32 mm) 腳位配置指南
ADSP-21060KS-160(240-mqfp-ep (32 x 32 mm) 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ADSP-21060KS-160.
請參閱 資料表 以查看完整腳位配置。
典型應用
ADSP-21060KS-160 適用於 6 應用s: Communications Signal Processing, Industrial Vibration Monitoring, Medical Signal Processing, Audio and Speech Processing, Imaging and Graphics Processing, Real-Time Control and Instrumentation.
Communications Signal Processing
The ADSP-21060KS-160 fits communications front ends that require continuous filtering, modulation, demodulation, or spectral analysis. Its 40 MHz clock and 120 MFLOPS floating-point throughput support parallel DSP operations, while the Super Harvard Architecture permits instruction and data transfers through independent buses. The 4 Mbits of dual-port on-chip SRAM reduce contention during filtering and FFT workloads. Designers should reserve external memory for larger buffers and verify DMA, clock-domain, and serial-interface timing against the system architecture before hardware release.
推薦
Industrial Vibration Monitoring
The ADSP-21060KS-160 is suitable for condition-monitoring equipment that extracts vibration features in real time. The 120 MFLOPS rating supports filtering, envelope analysis, FFT computation, and time-frequency transformations, while dual-port SRAM helps maintain streaming throughput. A 5 V processor simplifies integration with industrial analog front ends that require regulated rails and level translation. For machinery monitoring, validate signal-chain latency, dynamic range, watchdog behavior, and the thermal performance of the exposed pad before deploying the DSP in a sealed enclosure.
推薦
Medical Signal Processing
The ADSP-21060KS-160 can serve as the computational core in medical monitoring equipment performing real-time filtering, spectral analysis, and feature extraction from physiological signals. Its 32-bit floating-point computation at 120 MFLOPS provides numerical range and throughput for algorithms that combine filtering with spectral analysis. The 240-MQFP-EP package demands careful exposed-pad layout and thermal via placement, while its 5 V supply requires clean regulated power. Medical-system integrators must separately validate the complete signal chain, isolation strategy, safety requirements, and software controls.
推薦
Audio and Speech Processing
The ADSP-21060KS-160 fits audio processors that perform equalization, noise reduction, mixing, echo cancellation, or speech analysis in real time. Its 40 MHz clock and 120 MFLOPS floating-point performance support convolution and transform operations, and the 4 Mbits of internal dual-port SRAM can hold active filter state and timing buffers. The 32-bit path helps preserve numerical headroom in mixed fixed- and floating-point workflows. Audio implementations should confirm serial-port timing, DMA behavior, memory latency assumptions, and clock-generation stability before production use.
推薦
Imaging and Graphics Processing
The ADSP-21060KS-160 is applicable to imaging and graphics pipelines that require high-throughput convolution, filtering, motion analysis, or pixel-stream processing. Four independent Super Harvard Architecture buses support concurrent instruction execution and data movement, which is valuable when pixel data must be transferred while arithmetic units remain active. The processor's 120 MFLOPS rating and 32-bit data path provide useful computational headroom. System designers should characterize external-memory bandwidth, DMA behavior, cache or local-memory usage, and synchronization latency for the selected image resolution and frame rate.
推薦
Real-Time Control and Instrumentation
The ADSP-21060KS-160 supports control and instrumentation systems that combine feedback calculations with real-time waveform generation or analysis. Its 32-bit IEEE floating-point units simplify control-law and signal-chain implementation, while the independent buses improve concurrent data transfer. The 40 MHz operating rate provides a deterministic processing ceiling for many sensor, actuator, and measurement loops. Designers should account for peripheral latency, timer synchronization, interrupt latency, and the exposed-pad thermal path, particularly when the device is mounted next to power converters or precision analog components.
推薦
推薦產品摘要
工程參考資料,適用於 ADSP-21060KS-160 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ADSP-21060KSZ-160 | ADSP-21060LKS-160 | ADSP-21060LKSZ-160 | ADSP-21062KS-133 | ADSP-21061KS-160 |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 240-MQFP-EP (32 x 32 mm) | 240-MQFP-EP (32 x 32 mm) | 240-MQFP-EP (32 x 32 mm) | 240-MQFP-EP (32 x 32 mm) | 240-MQFP-EP (32 x 32 mm) | 240-MQFP-EP (32 x 32 mm) |
| Processor Type | 32-bit floating-point SHARC DSP | 32-bit floating-point SHARC DSP | ADSP-21060 family SHARC DSP | ADSP-21060L family SHARC DSP | 32-bit SHARC DSP | 32-bit SHARC DSP |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Architecture | Super Harvard Architecture with four independent buses | Super Harvard Architecture | Super Harvard Architecture | Super Harvard Architecture | Super Harvard Architecture | Super Harvard Architecture |
| Exposed Thermal Pad | Yes | Yes | Yes | Yes | Yes | Yes |
主要差異化特點
- Higher identified clock class than the ADSP-21062KS-133 option (對比ADSP-21062KS-133)
- Twice the on-chip SRAM of the ADSP-21062 family option (對比ADSP-21062KS-133)
- Direct same-clock ordering alternative for footprint reuse (對比ADSP-21060KSZ-160)
設計說明
Treat the exposed pad as the primary thermal path rather than an optional feature. Follow the Analog Devices package drawing for pad geometry, place thermal vias within the permitted region, and provide uninterrupted top- and bottom-layer copper where the board stack-up allows. Thermal performance depends strongly on copper area, via count, board material, and surrounding heat sources. Validate the finished assembly at the maximum expected ambient temperature and processing load.
Route clock, data, and memory interfaces according to the family hardware design guidance, keeping clock traces short and controlled. Place power and decoupling components close to their associated pins with very short return paths through the ground plane. The 240-lead package creates dense routing requirements, so check escape routing, layer transitions, impedance continuity, and exposed-pad clearance in the PCB library before releasing the layout.
Do not assume that every ADSP-2106x order code is firmware- and resource-identical. Check clock rating, SRAM capacity, memory organization, temperature grade, pin multiplexing, peripheral availability, and ordering options in the exact family datasheet and ordering guide. A mechanically compatible replacement can still require source-code changes, timing changes, or a different thermal qualification for the target application.
合規資訊
The manufacturer product page and family datasheet were used for device identification, but explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified. Confirm order-specific environmental and quality documentation before production release.