BCM53115UKFBG - 5-Port Gigabit Ethernet Switch | Broadcom
MPN: BCM53115UKFBG ✗ 停產BCM53115UKFBG 概覽
An Ethernet switch is a network-interface semiconductor that receives Ethernet frames from connected devices and forwards them toward their destinations using MAC-address information. The BCM53115UKFBG belongs to the broader hierarchy of Ethernet interface ICs, Ethernet switches, wired-network semiconductors, and communications semiconductors. Its integrated PHYs reduce the number of separate copper transceivers required in access equipment, gateways, and industrial Ethernet designs.
The principal identified features are five 10/100/1000-Mbps Ethernet ports, integrated Gigabit PHYs, and a 65 nm LP process implementation. Those characteristics make the device relevant to compact network appliances that need multiple copper Ethernet connections. Its multi-rate support allows each connected link to negotiate 10 Mbps, 100 Mbps, or 1 Gbps according to the capabilities of the attached device and the active network configuration.
BCM53115UKFBG is positioned for infrastructure and embedded networking applications rather than as a general-purpose processor. Integration can reduce board area by consolidating switching and PHY functions, while a single multi-port device can simplify power distribution and enclosure requirements. Designers must nevertheless verify the exact port mapping, media interfaces, management features, electrical limits, clock requirements, and thermal performance against the manufacturer datasheet before releasing a production PCB.
Typical uses include industrial Ethernet gateways, broadband access equipment, network edge appliances, embedded routers, and compact managed-switch products. In these systems, the integrated PHYs can support copper-facing ports while the switching section organizes traffic between local interfaces and an uplink. The five-port configuration is especially useful when a product needs several local device connections but does not require a larger switch port count.
The most important design step is to preserve the exact reference layout, ball assignment, power architecture, thermal arrangement, and interface configuration of the qualified 484-PBGA implementation. Place all high-speed Ethernet differential pairs on the multilayer PCB with continuous reference planes, controlled impedance, and minimal return-path discontinuities. Follow the manufacturer’s recommended decoupling and isolation layout rather than relying on a generic Ethernet-switch footprint.
This page organizes the confirmed BCM53115UKFBG port, speed, process, and positioning information into an engineering-oriented product record. It also separates the identified same-family comparison parts from unsupported substitutions and directs buyers to the Request a Quote form for current commercial availability, delivery, and sourcing information.
直接替換替代品,適用於 BCM53115UKFBG — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: BCM53115UKFBG (相同外形與佔位) — 差異在於 Product Type, Mounting Type.
BCM53115SKPBG
✅ 直接替換📋 參考替代品(不在目錄中)
BCM5324MKPBG
✅ 直接替換聯絡詢價
查看資料表 →BCM53346A0KFSBLG
✅ 直接替換聯絡詢價
查看資料表 →BCM53115UKFBG 最大額定值與電氣特性
| Product Type | 5-port Gigabit Ethernet switch with integrated PHYs |
| Ethernet Port Count | 5 ports |
| Supported Ethernet Speeds | 10 Mbps, 100 Mbps, and 1 Gbps |
| Integrated PHY Configuration | 7-port Gigabit Ethernet switch with integrated PHYs |
| Process Technology | 65 nm LP |
| Device Category | Ethernet interface IC |
| Product Subcategory | Ethernet switch |
BCM53115UKFBG standard 腳位配置指南
BCM53115UKFBG(standard 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: BCM53115UKFBG.
請參閱 資料表 以查看完整腳位配置。
典型應用
BCM53115UKFBG 適用於 6 應用s: Industrial Ethernet Gateway, Compact Network Edge Appliance, Broadband Access Equipment, Embedded Router and Control Console, Managed Local-Network Switch, Secure IP Camera Connection.
Industrial Ethernet Gateway
The BCM53115UKFBG is suitable for an industrial Ethernet gateway requiring five local copper connections at 10 Mbps, 100 Mbps, or 1 Gbps. Its integrated PHYs can simplify the physical-layer portion of the design and reduce component count compared with a discrete switch plus separate copper transceivers. The gateway’s processor can connect through the device’s management or switched data path, subject to confirmation of the supported interface and programming model. Thermal, isolation, surge, and EMC requirements remain system-level constraints that must be validated for the industrial environment.
推薦
Compact Network Edge Appliance
BCM53115UKFBG can support a compact edge appliance that combines several local Ethernet services with an uplink. Five confirmed ports operating across 10, 100, and 1000 Mbps provide flexibility for management, service, and storage connections at different link rates. Integrating the PHYs reduces the physical footprint needed for copper interfaces, while the 65 nm LP implementation identifies the device as a mature Ethernet-switch platform. Firmware configuration, traffic-management features, and the precise port map must be validated before the appliance design is frozen.
推薦
Broadband Access Equipment
The five-port configuration of BCM53115UKFBG fits broadband access equipment that needs multiple local Ethernet endpoints alongside service or uplink connectivity. Supporting 10 Mbps, 100 Mbps, and 1 Gbps allows deployed devices to operate at the highest common link rate while retaining compatibility with lower-speed legacy equipment. Integrated PHYs reduce the number of separate PHY components and associated routing complexity. For production equipment, check line-card timing, thermal limits, isolation requirements, and regulatory interface constraints specified by Broadcom.
推薦
Embedded Router and Control Console
BCM53115UKFBG can provide several wired Ethernet links in an embedded router or control console where local equipment must connect to an upstream network. The five-port arrangement can serve management, service, and endpoint connections, with each port operating at a negotiated rate from 10 Mbps through 1 Gbps. Integrated PHYs simplify the physical-layer implementation, but the designer must preserve the manufacturer’s differential-pair geometry and provide the specified power, clock, and decoupling network. Network-management features and software support should also be reviewed against the system architecture.
推薦
Managed Local-Network Switch
The BCM53115UKFBG is relevant to a small managed local-network switch because it combines five Ethernet ports with integrated PHYs and multi-rate link support. Devices operating at 10 Mbps or 100 Mbps can coexist with 1-Gbps endpoints, which is useful for legacy peripherals, IP cameras, and office equipment. The device can reduce the board area otherwise required for separate PHY circuitry. A production design must confirm management features, port isolation, spanning-tree or traffic-control behavior, and the exact configuration interface required by the network operating system.
推薦
Secure IP Camera Connection
BCM53115UKFBG can serve IP-camera and surveillance-network designs requiring several wired endpoints in a compact enclosure. The five ports support 10 Mbps, 100 Mbps, and 1 Gbps links, allowing the system to accommodate both high-bandwidth cameras and lower-rate accessory equipment. Integrated PHYs may reduce board space and component count, which is valuable in space-constrained housings. Before deployment, verify PoE requirements, surge protection, isolation, thermal performance, and whether any camera traffic-management or security feature requires a different switch configuration.
推薦
推薦產品摘要
工程參考資料,適用於 BCM53115UKFBG — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | BCM53115SKPBG | BCM5324MKPBG | BCM53346A0KFSBLG |
|---|---|---|---|---|
| Brand | Broadcom | Broadcom | Broadcom | Broadcom |
| Package | 484-PBGA | 484-PBGA (23 x 23 mm) | 484-PBGA | 484-PBGA |
| Mounting Type | Surface-mount PBGA | Surface-mount PBGA | Surface-mount PBGA | Surface-mount PBGA |
主要差異化特點
- Confirmed five-port Ethernet configuration (對比BCM53115SKPBG)
- Integrated multi-rate Gigabit PHYs (對比BCM5324MKPBG)
- Defined 65 nm LP process implementation (對比BCM53346A0KFSBLG)
- Five-port fit for local copper-network designs (對比BCM53346A0KFSBLG)
設計說明
Preserve the manufacturer reference layout for the BCM53115UKFBG 484-PBGA implementation. Route every Ethernet differential pair with uninterrupted reference planes below the pair, avoid split-plane crossings, and use the specified layer stack and impedance geometry. Keep the PHY, magnetics, and connector interface arrangement consistent with the evaluated design. A compact package does not reduce the high-speed layout requirements, and changes to the stack-up should be validated with channel and compliance testing.
Implement the complete Broadcom power tree, including the required core and Ethernet I/O supplies, rather than assuming one voltage can serve every ball group. Follow the datasheet’s recommended capacitor values, voltage ratings, placement, and startup sequencing. Check worst-case power dissipation across all five ports, including the effects of link activity and temperature. Estimated thermal calculations should use actual VIN, I/O current, package thermal data, and the final PCB copper geometry rather than a nominal condition.
Account for insertion loss, return loss, skew, and isolation in the complete channel from the switch ball to the network connector or magnetics. Maintain the manufacturer’s differential spacing and impedance geometry, provide uninterrupted return paths, and avoid placing noisy digital or power signals beneath Ethernet pairs. Validate the design with the intended PHY settings, line rate, connector, cable, and magnetics because a compliant controller layout alone does not guarantee compliant end-to-end Ethernet links.
Evaluate junction temperature under the maximum expected port-loading scenario and the highest ambient temperature permitted by the product enclosure. The 484-PBGA package requires adequate PCB copper and, where necessary, thermal vias connected to the thermal balls. Use the manufacturer’s thermal model or characterized board data for the final assembly. Do not assume that a laboratory board with large ground planes represents a compact production enclosure with restricted airflow.
Do not substitute a Broadcom Ethernet switch solely because it uses a PBGA package. Verify the exact ball map, pin voltages, clock source, reset requirements, management interface, PHY modes, reference-clock configuration, and software support before accepting BCM53115SKPBG, BCM5324MKPBG, or BCM53346A0KFSBLG as a replacement. A PCB footprint match is necessary but does not establish functional or pin-to-pin equivalence.
合規資訊
No definitive environmental or material-compliance declarations were confirmed for the exact ordering code. The device is a wired-network Ethernet interface IC rather than an automotive-qualified component.