CY8C4247AZI-L445 - 48MHz ARM Cortex-M0 PSoC 4200L MCU, 128KB Flash | Infineon
MPN： CY8C4247AZI-L445 ✓ 啟用中CY8C4247AZI-L445 概覽
What is a PSoC (Programmable System-on-Chip)? A PSoC is a microcontroller with a CPU core surrounded by programmable analog and digital Universal Digital Blocks (UDBs) and Universal Analog Blocks, all interconnected by a flexible routing matrix. PSoCs sit within the broader hierarchy of microcontroller -> embedded controller -> programmable SoC -> semiconductor. The PSoC 4 family uses a Cortex-M0 core (a 32-bit ARMv6-M architecture) and adds CAPSENSE™ capacitive-sensing IP, making these parts especially well suited to touch interfaces, slider/proximity sensing, and industrial HMI front-ends.
Key features of the CY8C4247AZI-L445 include a 1.71–5.5 V wide VDD range, a 4-channel DMA controller, a 4-input 12-bit SAR ADC with up to 1 Msps throughput, two IDAC channels, four TCPWM blocks, and a full-speed USB 2.0 FS controller with an internal 3-pin. The integrated CAPSENSE™ Sigma-Delta (CSD) block provides hardware-accelerated capacitive touch sensing with SmartSense™ auto-tuning, eliminating manual PCB and firmware compensation.
Architecturally, the device combines the 48 MHz Cortex-M0 core with an ultra-low-power Always-On (AOL) domain that keeps key peripherals alive in Deep Sleep modes down to typical 1.3 µA. This dual-domain partitioning allows active CPU execution and Always-On event monitoring to coexist, making it well suited to battery-powered products that must wake on touch or sensor events while sleeping between interactions.
Typical applications include CAPSENSE™ touch-Button / slider / proximity user interfaces, USB HID peripherals such as mice and keyboards, low-power IoT endpoints with wake-on-touch, industrial control panels, smart-home appliances, e-metering front-ends, and PC peripherals. Designers should plan PCB copper pours carefully because the 64-TQFP-10x10 package has limited thermal headroom under simultaneous USB + ADC + touch-sensing load; a minimum 4-layer stack-up with a continuous ground plane is recommended for industrial designs.
直接替換替代品，適用於 CY8C4247AZI-L445 — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： CY8C4247AZI-L445 （相同外形與佔位） — 差異在於 Core, Package, Operating Temperature Range, Programmable Analog Blocks, TCPWM Blocks.
CY8C4247AZI-L423T
✅ 直接替換聯絡詢價
查看資料表 →CY8C4247AZI-L423T
✅ 直接替換聯絡詢價
查看資料表 →CY8C4247BZI-L489
✅ 直接替換📋 參考替代品（不在目錄中）
CY8C4247BZI-L479
✅ 直接替換📋 參考替代品（不在目錄中）
CY8C4246AZI-M445
✅ 直接替換聯絡詢價
查看資料表 →CY8C4247AZI-L445 最大額定值與電氣特性
| Series | PSoC™ 4200L (CY8C42xx-L) |
| Core | ARM® Cortex®-M0 (32-bit) |
| Maximum CPU Clock | 48 MHz |
| 封裝 | 64-TQFP (10x10 mm) |
| Programmable Analog Blocks | 4 |
| Programmable Digital Blocks (UDBs) | 4 |
| SAR ADC | 12-bit, 1 Msps |
| USB Controller | USB 2.0 Full-Speed with internal 3-pin |
| TCPWM Blocks | 4 (Timer/Counter/PWM) |
| RoHS 狀態 | Compliant |
CY8C4247AZI-L445 64-tqfp (10x10 mm) 腳位配置指南
CY8C4247AZI-L445（64-tqfp (10x10 mm) 封裝）的腳位配置。 此數位 IC 包含 GPIO、通訊介面（UART、SPI、I2C）與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料： CY8C4247AZI-L445.
請參閱 資料表 以查看完整腳位配置。
典型應用
CY8C4247AZI-L445 適用於 7 應用s: CAPSENSE™ Touch User Interface, USB HID Peripheral (Mouse / Keyboard / Gamepad), Low-Power IoT Sensor Node, Smart Home Appliance Control, Industrial HMI Front-End, PC Peripheral / Gaming Accessory, Electronic Metering Front-End.
CAPSENSE™ Touch User Interface
The CY8C4247AZI-L445 is built specifically for hardware-accelerated capacitive touch sensing via its on-chip CSD CAPSENSE™ block. With SmartSense™ auto-tuning, designers can deploy up to 36 capacitive buttons, sliders, or proximity sensors without manual PCB compensation, while the 4 UDBs run as additional PWM/Quadrature Decoder logic. The 128 KB flash holds a full CapSense firmware stack with room for gesture firmware and HMI overlays, making this PSoC 4 ideal for white-goods, industrial panels, and PC peripherals.
推薦
USB HID Peripheral (Mouse / Keyboard / Gamepad)
The CY8C4247AZI-L445 integrates a full-speed USB 2.0 controller with internal 3-pin termination, dramatically reducing external component count in HID peripherals such as keyboards, mice, or gamepad controllers. Its 128 KB flash and 16 KB SRAM host a USB HID class driver plus CAPSENSE™ firmware for trackpad/scroll-wheel inputs. The 48 MHz Cortex-M0 supports HID polling rates up to 1000 Hz with full interrupt latency headroom, and the 1.71–5.5 V supply range supports both 3.3 V USB-regulated and 5 V VBUS-powered designs.
推薦
Low-Power IoT Sensor Node
The CY8C4247AZI-L445's ultra-low 1.3 µA Deep Sleep current with SRAM retention lets battery-powered IoT nodes sleep for months between sensor events. The Always-On AOL peripheral domain allows RTC-driven or CAPSENSE™ wake-up events to fire without waking the CPU. With its 12-bit SAR ADC sampling at 1 Msps and the 4 IDAC channels for sensor excitation, the PSoC 4 serves as a low-power front-end for environmental, gas, or motion sensor hubs that transmit via an external BLE/Zigbee module.
推薦
Smart Home Appliance Control
The CY8C4247AZI-L445's combination of 4 programmable analog blocks (for op-amp/comparator/LDT/PGA-low-noise filters), TCPWM motor-control timers, and CAPSENSE™ touch makes it a single-chip solution for smart appliances like coffee machines, washing-machine control panels, and induction cooktops. The 5.5 V maximum VDD tolerates noisy 24 V→5 V supply rails with simple LDO filtering. Infineon's SmartSense™ auto-tuning allows the touch UI to survive water spills and glove-touch, which are critical for kitchen and laundry use-cases.
推薦
Industrial HMI Front-End
The CY8C4247AZI-L445 supports industrial control panels with a 12-bit SAR ADC sampling at 1 Msps for analog sensor readout (4–20 mA loops via external resistor), CAPSENSE™ for operator buttons, and the USB controller for diagnostic-port connectivity. Its industrial -40 °C to +85 °C temperature grade and 50,000-cycle flash endurance support the long-life requirements of factory-automation equipment. The PSoC 4's UDBs can implement custom Modbus RTU framing in hardware without offloading the CPU.
推薦
PC Peripheral / Gaming Accessory
The CY8C4247AZI-L445 serves as a USB-attached PC peripheral controller for gaming mice, RGB keyboards, or stream-controller decks, combining CAPSENSE™ slider/button inputs, native USB Full-Speed, and 128 KB flash to host RGB lighting firmware and HID-class drivers. The 4 TCPWM blocks drive addressable RGB LED strips without CPU overhead, and the 4 IDACs drive force-feedback or haptic-driver circuitry. The 48 MHz Cortex-M0 with DMA supports polling rates above 1000 Hz for competitive-gaming mice.
推薦
Electronic Metering Front-End
The CY8C4247AZI-L445's 12-bit SAR ADC (1 Msps), 4 IDAC channels for sensor excitation, and TCPWM timers for pulse counting make it well suited to e-metering front-ends (electricity, water, or gas meters). The 5.5 V VDD tolerance simplifies connection to 3.6 V Li-SOCl2 battery packs common in metering. The 4 UDBs can implement tamper-detection logic in hardware, offloading the Cortex-M0 CPU for guaranteed response to magnetic tamper events. Lifecycle: 50k flash cycles meet typical 15-year metering lifetime requirements.
推薦
推薦產品摘要
工程參考資料，適用於 CY8C4247AZI-L445 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | CY8C4247AZI-L423 | CY8C4247AZI-L423T | CY8C4247BZI-L489 | CY8C4247BZI-L479 | CY8C4246AZI-M445 |
|---|---|---|---|---|---|---|
| Package | 64-TQFP (10x10) | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same | 64-TQFP (10x10) - same |
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon | Infineon |
| Program Flash | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB | 64 KB |
| SRAM | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| CPU Clock | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Operating Temperature | -40 °C to +85 °C (Industrial) | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +105 °C | -40 °C to +85 °C | -40 °C to +85 °C |
| Supply Voltage | 1.71–5.5 V | 1.71–5.5 V | 1.71–5.5 V | 1.71–5.5 V | 1.71–5.5 V | 1.71–5.5 V |
| USB Controller | USB 2.0 FS, integrated 3-pin | USB 2.0 FS, integrated 3-pin | USB 2.0 FS, integrated 3-pin | USB 2.0 FS, integrated 3-pin | USB 2.0 FS, integrated 3-pin | USB 2.0 FS, integrated 3-pin |
| CAPSENSE™ CSD | Yes (up to 36 channels) | Yes | Yes | Yes | Yes | Yes |
主要差異化特點
- Industrial -40 °C to +85 °C operating range with full CAPSENSE™ (對比CY8C4247AZI-L423)
- 128 KB flash for full CAPSENSE™ + USB stack + RGB firmware (對比CY8C4246AZI-M445)
- Same-family pin-compatible drop-in to CY8C4247BZI-L489 (對比CY8C4247BZI-L489)
- Integrated USB 2.0 Full-Speed controller with internal 3-pin (對比CY8C4247BZI-L479)
設計說明
The 64-TQFP-10x10 package has limited thermal headroom under simultaneous USB + ADC + CAPSENSE load. Recommended PCB stack-up: 4-layer FR-4 with the second internal layer as a continuous ground plane; provide at least 25 mm² of top-layer copper pour stitched to GND with 0.3 mm vias on a 1 mm grid to keep junction temperature below 90 °C at 48 MHz full CPU load. Place VDD and VDDD decoupling capacitors within 2 mm of the pins, using 100 nF X7R in parallel with 4.7 µF X5R per the PSoC 4 hardware design considerations guide.
CAPSENSE™ button/slider sensors must be routed on a dedicated layer (no copper pour beneath) and guarded by a hatched ground trace per AN92239. Each CSD pin's series resistor (typically 560 Ω) must be placed within 5 mm of the MCU pin, and the shield electrode must be connected to a dedicated GPIO configured by GPIO vs DRV=0 in firmware. Avoid running noisy USB or PWM traces parallel to CSD sensor traces; cross TRH = 90° if traces must intersect to maintain CAPSENSE™ SNR above 5:1.
Do not omit the external VDDD→VDD core-decoupling capacitor pair (1 µF + 100 nF X7R within 5 mm of pin). Do not route the USB D+/D– traces more than 25 mm or with a 90 Ω differential-impedance mismatch; an improper USB layout causes enumeration issues with no firmware-side fix. Also, when designing for industrial temperature, do not use the L423 commercial-grade variant in place of the L445 — the L423's reduced operating-temperature range can cause CAPSENSE™ SNR drift outside the SmartSense™ compensation window below 0 °C.
The CY8C4247AZI-L445 supports Deep Sleep at ~1.3 µA with full SRAM retention. To minimize sleep current, ensure unused GPIOs are configured as Analog Hi-Z (drive mode 0xC0) rather than the default pull-up state. The AOL domain's RTC can be sourced from the internal WCO (32.768 kHz) to wake the part periodically without an external crystal, but the WCO must be enabled via the clock-tree configuration in PSoC Creator or ModusToolbox firmware.
合規資訊
RoHS compliant per Infineon product page; AEC-Q100 not applicable (industrial MCU, not automotive qualified). Halogen-free per Infineon PSoC 4 family environmental compliance statement.
