ISL84781IV - 8:1 Analog Multiplexer, 750mOhm | Renesas
MPN: ISL84781IV ✓ 啟用中ISL84781IV 概覽
An analog multiplexer is a semiconductor switch that connects one source signal to a shared destination under digital control. The ISL84781IV belongs to the analog-switch and multiplexer hierarchy within interface ICs, where it sits between external signal sources and downstream measurement or processing circuitry. Its low on-resistance helps limit signal attenuation when the selected channel carries a sensor, voltage, or low-current analog signal.
The main characteristics are an 8:1 circuit configuration, 750mOhm on-resistance, single-supply operation, and a 16-pin TSSOP package. The low on-resistance is particularly important because the resistance of the selected switch appears in series with the signal path. Lower series resistance can reduce amplitude loss and improve signal integrity when driving the next circuit stage. The compact TSSOP outline also supports designs that require a modest PCB footprint rather than a larger multiplexed-switch package.
ISL84781IV is appropriate when one analog source must be selected from eight candidates. Typical uses include multiplexed sensor inputs, programmable signal routing, laboratory measurement interfaces, communication front ends, and embedded analog test systems. Digital select controls determine which input is connected, allowing a microcontroller or other controller to scan channels sequentially. The selected signal is then evaluated by an ADC, comparator, amplifier, or measurement instrument.
Designers should verify the exact supply-voltage range, input-signal range, channel leakage, switching time, and control-logic levels against the manufacturer datasheet before finalizing a circuit. Signal-path capacitance and off-channel behavior can affect sampling accuracy, especially when multiplexing sensors with substantially different impedances or when switching between very low-level signals. The 16-pin TSSOP footprint also requires appropriate land-pattern design and careful decoupling close to the supply pins.
The ISL84781IV provides a compact, low-resistance analog routing solution for designers who need an 8:1 multiplexer in a 16-pin TSSOP. Its combination of single-supply operation, 8:1 channel selection, and 750mOhm on-resistance makes it a practical building block for analog measurement and control systems where channel count, signal attenuation, and board area are important design constraints.
直接替換替代品,適用於 ISL84781IV — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
ISL84781IV-T
✅ 直接替換📋 參考替代品(不在目錄中)
MAX4781EUE+T
✅ 直接替換📋 參考替代品(不在目錄中)
ISL84781IV 規格
| Circuit Count | 1 circuit |
| Multiplexer Configuration | 8:1 |
| On-Resistance | 750 mOhm |
| Supply Type | Single supply |
| Voltage Class | Low voltage |
| Device Type | Analog multiplexer |
| 封裝 | 16-pin TSSOP |
| 安裝類型 | Surface mount |
| Number of Channels | 8 |
| RoHS 狀態 | compliant |
ISL84781IV 16-pin tssop 腳位配置指南
ISL84781IV(16-pin tssop 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ISL84781IV.
請參閱 資料表 以查看完整腳位配置。
典型應用
ISL84781IV 適用於 6 應用s: Multiplexed Sensor Acquisition, Programmable Test and Measurement, Analog Signal Routing, Industrial Control Interface, Communication Front-End Conditioning, Portable Measurement Device.
Multiplexed Sensor Acquisition
The ISL84781IV can route one of eight compatible analog sensor outputs to a shared amplifier or ADC input. Its 750mOhm on-resistance limits the switch's contribution to series signal loss, while the 8:1 architecture reduces the number of analog input channels required on the measuring device. Check the datasheet for leakage, input-range limits, and switching-time requirements before using it with high-impedance sensors. Source impedance and the time allowed for the ADC to settle can be more important than nominal on-resistance when the signals are small, slow, or highly sensitive.
推薦
Programmable Test and Measurement
The ISL84781IV is useful in measurement fixtures that must connect one of eight test inputs to a common instrument channel. Its single-supply, low-voltage operation suits compact automated test equipment, and the 16-pin TSSOP package preserves PCB area. The 750mOhm on-resistance can reduce insertion loss in the selected path, although the complete measurement accuracy still depends on switch leakage, off-channel behavior, settling time, and the impedance of the source under test. Use the manufacturer pin table and application guidance to implement deterministic select sequencing.
推薦
Analog Signal Routing
The ISL84781IV can act as a programmable analog selector between external sources and a downstream signal-conditioning block. Its eight channels and 750mOhm on-resistance provide a compact way to share a sensitive amplifier or converter across several voltage sources. The device is best suited to signals that remain within the manufacturer's specified common-mode and voltage limits. For precision applications, account for channel-to-channel resistance variation, leakage into unselected channels, and any charging required at switched nodes. Controlled settling before sampling helps avoid interpreting transition behavior as a genuine input change.
推薦
Industrial Control Interface
The ISL84781IV can consolidate multiple analog plant or process signals into a controller-accessible path. The 8:1 configuration allows a microcontroller to monitor up to eight compatible channels sequentially, while the low 750mOhm on-resistance helps preserve signal amplitude. Industrial suitability must be evaluated against the exact operating-temperature, supply-voltage, and compliance requirements rather than inferred from the package. Design the firmware to ignore transients during channel changes, allocate sufficient acquisition settling time, and ensure that the selected signal stays within the switch's specified voltage range.
推薦
Communication Front-End Conditioning
The ISL84781IV can select among several low-level analog communication paths before amplification or conversion. Its low on-resistance makes it a plausible choice when switching losses must remain small relative to the signal amplitude, while the 8:1 arrangement allows multiple inputs to share one downstream receiver. Verify the exact supply range, signal swing, off-isolation, and switching transient behavior in the manufacturer datasheet. Layout should keep the selected route short and provide stable reference and bypass connections, since long traces and poorly decoupled supply nodes can degrade an otherwise low-resistance switching path.
推薦
Portable Measurement Device
The ISL84781IV supports compact handheld or portable instruments that need several analog inputs without allocating a separate front end for each channel. Its 16-pin TSSOP package limits board area, and its 750mOhm on-resistance provides a relatively low-resistance route from the selected input to the common output. Battery-powered equipment still requires careful attention to supply range, quiescent behavior, and signal settling. Confirm the complete operating limits, and design the control sequence so the converter does not sample during a switch transition. This improves repeatability when the measured quantity changes significantly between channels.
推薦
工程參考資料,適用於 ISL84781IV — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ISL84781IV-T | MAX4781EUE+T |
|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Analog Devices |
| Package | 16-pin TSSOP | 16-pin TSSOP - same package | 16-pin TSSOP - same package |
| Multiplexer Configuration | 8:1 | 8:1 | 8-channel multiplexer |
| Supply Type | Single supply | Single supply | Low-voltage device; exact supply configuration not stated |
| Device Type | Low-voltage analog multiplexer | Low-voltage analog multiplexer | High-speed low-voltage CMOS analog multiplexer |
| Mounting Type | Surface mount | Surface mount | Surface mount |
主要差異化特點
- Low-resistance eight-way analog routing (對比MAX4781EUE+T)
- Directly related same-family order code (對比ISL84781IV-T)
- Single-supply low-voltage architecture (對比MAX4781EUE+T)
設計說明
Treat the selected switch resistance, source impedance, load impedance, and ADC sampling capacitor as one signal path. The specified 750mOhm on-resistance can add attenuation in a divider with a much lower source impedance, while a high-impedance source can dominate the error. Allow sufficient settling time after changing the selection, and sample only after the new channel has reached the required accuracy.
Place bypass capacitance close to the supply and ground pins, and route the eight analog inputs directly to their assigned pins. Keep the common output path away from digital select traces and switching nodes to reduce capacitive coupling. Use the manufacturer pin-description table for the exact 16-pin TSSOP footprint and confirm whether any exposed-pad or thermal requirements apply before releasing the layout.
Do not assume that matching channel count and package size guarantees drop-in compatibility. Before substituting a part, verify pin names, select logic levels, supply polarity, analog signal range, on-resistance, leakage, off-isolation, and switching speed against both manufacturer datasheets. Also confirm the complete order code because packaging suffixes can change reel format or procurement conditions without changing core functionality.
合規資訊
RoHS compliance is identified in the product listing. Other compliance attributes require confirmation from the manufacturer or supply documentation.