LM2903MX-ON - Dual Open-Collector Comparator | onsemi
MPN: LM2903MX-ON ✓ 啟用中LM2903MX-ON 概覽
A voltage comparator is an analog integrated circuit that compares two input voltages and switches its output when the difference crosses a specified threshold. The LM2903 family belongs to the comparator hierarchy, which sits within analog and mixed-signal semiconductors used for threshold detection, sensing, and control. Its two channels can operate independently from a shared supply, allowing one device to implement two comparison functions in a compact footprint.
The primary features of the LM2903MX-ON are its dual-channel architecture, open-collector outputs, wide operating supply range, and low-offset capability. Open-collector outputs permit an external pull-up resistor to establish the output logic level. This arrangement supports wired-AND behavior and allows interface levels to be selected by changing the pull-up supply rather than relying on a dedicated output-supply pin.
Each internal comparator has two inputs and one output. With single-supply operation, the common-mode input range can include ground, making the device useful for monitoring signals near 0 V. Split-supply operation permits comparison around a midpoint reference. Because the two channels are independent, they can compare separate sensor or threshold pairs while sharing the same package and supply architecture.
Typical applications include industrial sensor interfaces, battery and power-system monitoring, control-loop threshold detection, window comparison, and general-purpose digital conditioning. The dual channel reduces board area when two independently referenced signals must be evaluated. The open-collector architecture is especially useful where the output must drive a pull-up rail, connect to a wired logic bus, or interface with a microcontroller input.
PCB design should reserve a pull-up resistor for each open-collector output and route the input and output paths away from high-current switching nodes. The wide 2 V to 36 V supply range supports both low-voltage systems and higher industrial rails, but input and output operating conditions must remain within their respective absolute maximum ratings.
This product page combines the LM2903MX-ON technical characteristics, verified manufacturer information, pin-level guidance, drop-in alternatives, and practical design considerations. These engineering details help shorten component selection and support direct PCB, sourcing, and lifecycle planning for dual-comparator designs.
直接替換替代品,適用於 LM2903MX-ON — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2903MX-ON (相同外形與佔位) — 差異在於 Operating Temperature Range, Comparator Type, Package, Output Type, Supply Current.
LM2903M
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →LM2903MX
✅ 直接替換聯絡詢價
查看資料表 →LM2903MX/NOPB
✅ 直接替換聯絡詢價
查看資料表 →LM2903MX-ON 最大額定值與電氣特性
| Comparator Type | Dual differential voltage comparator |
| Number of Channels | 2 channels |
| 輸出類型 | Open collector |
| Supply Voltage Range | 2 V to 36 V |
| Input Offset Voltage | 2.0 mV maximum |
| Common-Mode Input Range | Extends to ground in single-supply operation |
| Operating Supply Mode | Single supply or split supply |
| 工作溫度範圍 | -40°C to +85°C |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
| Channel Independence | 2 independent comparator channels |
| Output Pull-Up | External pull-up resistor required |
| Wired-AND Capability | Supported by open-collector outputs |
LM2903MX-ON 腳位配置
| 腳位 1 | OUT1 — Comparator 1 open-collector output |
| 腳位 2 | IN1- — Comparator 1 inverting input |
| 腳位 3 | IN1+ — Comparator 1 non-inverting input |
| 腳位 4 | GND — Ground connection |
| 腳位 5 | IN2+ — Comparator 2 non-inverting input |
| 腳位 6 | IN2- — Comparator 2 inverting input |
| 腳位 7 | OUT2 — Comparator 2 open-collector output |
| 腳位 8 | VCC — Positive supply connection |
典型應用
LM2903MX-ON 適用於 6 應用s: Industrial Sensor Threshold Detection, Battery Voltage Monitoring, Power-System Window Comparison, Motor and Solenoid Control Interface, Consumer Equipment Signal Conditioning, Portable and Wearable Device Sensing.
Industrial Sensor Threshold Detection
The LM2903MX-ON fits industrial sensor interfaces that require a reliable decision when a signal crosses a defined threshold. Its two independent comparator channels can evaluate two sensor conditions without using two packages, while the single-supply common-mode range extending to ground is useful for signals near 0 V. Input offset voltage as low as 2.0 mV helps reduce the sensing gap near the switching point. Place the device close to the sensor-conditioning network, keep sensitive inputs away from switching traces, and use the open-collector outputs with pull-up resistors matched to the controller interface.
推薦
Battery Voltage Monitoring
The LM2903MX-ON can monitor battery-related voltages in portable equipment, industrial packs, and backup-power systems. Its supply capability from 2 V to 36 V permits operation across a broad range of rails, while the two channels can implement independent threshold checks when one channel monitors the pack and the other monitors a protected rail. The common-mode range extending to ground supports low-voltage discharge detection. Use resistor-divider inputs with suitable tolerances, account for input offset voltage as low as 2.0 mV, and select pull-up values that satisfy both leakage and output-transition requirements.
推薦
Power-System Window Comparison
A dual comparator is well suited to upper and lower power-rail window checks, and the LM2903MX-ON provides two independent channels in one 8-pin SOIC. The device operates from 2 V to 36 V and supports split-supply operation, allowing both positive and negative threshold signals to be compared around a reference. Input offset voltage as low as 2.0 mV is valuable when the monitored window is narrow. Define resistor-divider ratios for both limits, keep the reference network away from noisy power stages, and route the two open-collector outputs to the appropriate pull-up rails.
推薦
Motor and Solenoid Control Interface
The LM2903MX-ON can generate a control decision from current-sensor, position-sensor, or protection signals in motor and solenoid systems. Its dual architecture permits two related control functions, while the broad 2 V to 36 V supply range supports industrial control environments. The open-collector output is useful when the decision must drive a transistor stage or participate in wired logic. Because motor environments contain switching noise, keep comparator inputs short and separated from motor-current paths. Use the manufacturer pin description and absolute maximum ratings when designing protection around transients and supply disturbances.
推薦
Consumer Equipment Signal Conditioning
The LM2903MX-ON is suitable for compact consumer and communication equipment that needs to convert analog levels into logic-compatible decisions. Two channels can handle separate threshold functions in an 8-pin SOIC, reducing component count. Its 2 V to 36 V operating supply range covers low-voltage digital systems and higher rails, and the single-supply common-mode range extends to ground for low-level signals. Connect each output through a pull-up resistor, choose the pull-up voltage to match the receiving logic, and place bypass capacitance close to the supply pin according to the manufacturer application guidance.
推薦
Portable and Wearable Device Sensing
Portable equipment can use the LM2903MX-ON to detect low-level events such as a falling battery signal, sensor threshold crossing, or a system rail moving outside its acceptable window. The dual-channel architecture saves board area, and the common-mode range extending to ground is useful with sensors referenced to 0 V. The 2 V minimum supply operation supports low-voltage systems. Input offset voltage as low as 2.0 mV helps resolve small transitions, but careful resistor selection is still required. Keep the PCB footprint compact, route the open-collector outputs away from radio-frequency and switching paths, and confirm the pull-up current against battery-saving requirements.
推薦
推薦產品摘要
工程參考資料,適用於 LM2903MX-ON — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2903M | LM2903MX | LM2903MX/NOPB | LM2903MX | LM2903MX |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments | ROHM Semiconductor |
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same |
| Comparator Configuration | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator |
| Number of Independent Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
| Supply Voltage Range | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V |
| Input Offset Voltage | 2.0 mV maximum | 2.0 mV maximum | 2.0 mV maximum | 2.0 mV maximum | 2.0 mV maximum | 2.0 mV maximum |
| Operating Temperature Range | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C |
| Common-Mode Input Range | Extends to ground in single-supply operation | Extends to ground in single-supply operation | Extends to ground in single-supply operation | Extends to ground in single-supply operation | Extends to ground in single-supply operation | Extends to ground in single-supply operation |
主要差異化特點
- Exact onsemi supplier continuity (對比LM2903MX/NOPB)
- Wide supply compatibility (對比LM2903MX)
- Low-level threshold sensitivity (對比LM2903M)
設計說明
Route the two comparator inputs as short, low-impedance nets and keep them away from switching nodes, power inductors, and high-current return paths. A small ground plane under the device and a direct ground connection at pin 4 help prevent output transitions from coupling into the input threshold. Place the output pull-up resistors near the destination device when long traces would increase transition time or susceptibility to interference.
Do not treat the open-collector output as a actively driven logic output. Each output requires a pull-up resistor, and its maximum low-level sink current must remain within the device rating. When several outputs share one pull-up, confirm that the combined sink current does not pull the bus below its valid logic level. Also check unused input pins so they do not float near a switching threshold.
Add the supply bypass capacitance specified by the manufacturer close to the VCC and ground pins. The 2 V to 36 V operating range does not imply that every intermediate rail has identical transient performance, especially when the comparator is mounted near a switching regulator. Keep the supply loop compact and provide local decoupling so comparator switching does not add disturbance to the power rail being monitored.
For low-level threshold detection, account for the 2.0 mV maximum input offset and temperature-dependent behavior when defining the switching margin. Keep the reference divider close to the input pin and use resistor tolerances appropriate to the required threshold accuracy. If the comparator output drives a long cable or slow digital input, select the pull-up value with the complete input capacitance and leakage budget rather than only the minimum sink current.
合規資訊
The LM2903MX-ON is a comparator integrated circuit and is therefore not applicable to AEC-Q100 qualification. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer or the exact orderable-device documentation.