LT1007ACP - Low-Noise Precision Op Amp | Texas Instruments
MPN: LT1007ACP ✗ 停產LT1007ACP 概覽
An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The LT1007 belongs to the precision operational-amplifier hierarchy, combining low-noise input stages, low input offset voltage, low temperature drift, and high common-mode and power-supply rejection. This makes it useful within measurement, instrumentation, audio, and precision analog systems.
The LT1007 family provides maximum equivalent input noise voltage of 3.8 nV/sqrt(Hz) at 1 kHz and 4.5 nV/sqrt(Hz) at 10 Hz, with a typical low-frequency peak-to-peak equivalent input noise voltage of 60 nV from 10 Hz. Its typical input offset voltage is 10 uV, while its input voltage drift is 0.2 uV/degree C. Common-mode rejection and power-supply rejection are specified at 130 dB, supporting accurate amplification in circuits exposed to supply or common-mode disturbances.
The amplifier is capable of high open-loop gain, with a typical differential voltage amplification of 20 V/uV at 25 degrees C while driving a 2 kOhm load to plus or minus 12 V. The family also supports high-speed operation, with a minimum slew rate of 11 V/us for the LT1037 and LT1037A versions. The combination of precision, low noise, and speed is particularly useful for sensor front ends and high-gain signal conditioning.
Typical applications include low-level sensor instrumentation, strain-gauge and bridge amplifiers, precision current measurement, audio preamplification, laboratory measurement equipment, and industrial analog signal chains. The high rejection ratio helps reduce errors caused by common-mode voltage and supply variation, while the low offset drift supports stable calibration over temperature.
When designing around the LT1007ACP, check the required gain stability, supply voltage, load conditions, and compensation requirements against the device family data. Decoupling capacitors should be placed close to the supply pins, and the input and feedback paths should be kept short to minimize parasitic capacitance and noise pickup.
This product page combines the device specifications, verified source links, application guidance, and package-level design considerations for engineers evaluating the LT1007ACP in precision analog systems.
直接替換替代品,適用於 LT1007ACP — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LT1007ACP (相同外形與佔位) — 差異在於 Package.
LT1007CN8#PBF
✅ 直接替換📋 參考替代品(不在目錄中)
LT1007ACN8#PBF
✅ 直接替換📋 參考替代品(不在目錄中)
LT1007ACP 最大額定值與電氣特性
| Product Type | Low-noise, high-speed, precision operational amplifier |
| Number of Amplifiers | 1 amplifier |
| 封裝 | 8-pin PDIP |
| Maximum Equivalent Input Noise Voltage | 3.8 nV/sqrt(Hz) at 1 kHz |
| Equivalent Input Noise Voltage | 4.5 nV/sqrt(Hz) at 10 Hz |
| Low Peak-to-Peak Equivalent Input Noise Voltage | 60 nV typical from 10 Hz |
| Typical Input Offset Voltage | 10 uV |
| Input Voltage Drift | 0.2 uV/degree C |
| Common-Mode Rejection | 130 dB |
| Power-Supply Rejection | 130 dB |
| Gain-Bandwidth Product | 60 MHz on the decompensated LT1037 |
| Typical Differential Voltage Gain | 20 V/uV at 25 degrees C with a 2 kOhm load to plus or minus 12 V |
| Minimum Slew Rate | 11 V/us for LT1037 and LT1037A versions |
| 安裝類型 | Through-hole |
LT1007ACP 8-pin pdip 腳位配置指南
LT1007ACP(8-pin pdip 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LT1007ACP.
請參閱 資料表 以查看完整腳位配置。
典型應用
LT1007ACP 適用於 6 應用s: Low-Level Sensor Instrumentation, Strain-Gauge and Bridge Signal Conditioning, Precision Audio Preamplification, Laboratory Measurement Equipment, Industrial Process Signal Conditioning, High-Speed Analog Signal Conditioning.
Low-Level Sensor Instrumentation
The LT1007ACP fits low-level sensor front ends where the source voltage can be close to the amplifier offset and noise floor. Its 10 uV typical input offset voltage, 0.2 uV/degree C drift, and 3.8 nV/sqrt(Hz) input noise at 1 kHz help preserve the integrity of small sensor signals before digitization. The 130 dB common-mode rejection is useful when the sensor is referenced to ground and the input node experiences common-mode variation. The circuit should use short, shielded input routes, clean grounding, and feedback resistors selected for the required closed-loop gain and bandwidth.
推薦
Strain-Gauge and Bridge Signal Conditioning
The LT1007ACP is suitable for strain-gauge, resistive-bridge, and precision differential measurement circuits where millivolt-level signals must be amplified accurately. The low 10 uV typical offset and 0.2 uV/degree C drift reduce errors that would otherwise vary with sensor mounting or ambient temperature. Its high common-mode rejection of 130 dB helps reject the larger common-mode voltage present around a bridge output. For best results, keep the bridge excitation and amplifier input paths short, use matched resistor networks, and verify the closed-loop gain and output-swing limits against the specific bridge excitation.
推薦
Precision Audio Preamplification
The LT1007ACP can be used in low-noise audio preamplifier stages requiring a precision operational amplifier rather than a general-purpose audio device. The 60 nV typical peak-to-peak equivalent input noise from 10 Hz supports low-level signal conditioning, while the 60 MHz gain-bandwidth product in the decompensated LT1037 family provides useful high-speed capability. The actual usable audio bandwidth and distortion must be checked for the exact device variant, gain, load, and supply conditions. Use short signal traces, adequate supply bypassing, and a feedback topology that remains stable at the intended noise-gain setting.
推薦
Laboratory Measurement Equipment
The LT1007ACP is appropriate for laboratory and test-equipment input stages that combine low noise with accurate offset behavior. Its 130 dB power-supply rejection helps isolate the measured signal from supply variations, and its low offset drift supports repeatable readings over time and temperature. The amplifier can therefore support buffer, gain, and differential sensing functions around laboratory sensors. Designers should still account for the exact supply voltage, output swing, load, and compensation requirements, and should provide local bypass capacitors close to the supply pins.
推薦
Industrial Process Signal Conditioning
The LT1007ACP can amplify low-level process signals in industrial control and monitoring systems where a common-mode voltage and supply noise are present. Its common-mode and power-supply rejection ratings of 130 dB help preserve signal integrity, while the 3.8 nV/sqrt(Hz) noise specification supports low-level input stages. The component should be selected only after confirming operating-temperature, supply, and output-swing requirements for the industrial environment. Practical implementations benefit from guarded PCB traces, controlled grounding, and feedback-component layouts that minimize leakage and parasitic coupling.
推薦
High-Speed Analog Signal Conditioning
The LT1007ACP family is positioned for applications that need more bandwidth than a conventional precision op amp. The manufacturer identifies a 60 MHz gain-bandwidth product for the decompensated LT1037 and a minimum slew rate of 11 V/us for the LT1037 and LT1037A versions, making the family relevant to fast analog signal paths. The exact LT1007ACP gain-stability configuration must be confirmed before selecting the feedback network. Control board capacitance, maintain short feedback traces, and use a resistor and capacitor combination that matches the required gain and compensation behavior.
推薦
推薦產品摘要
工程參考資料,適用於 LT1007ACP — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LT1007CN8#PBF | LT1007ACN8#PBF | LT1007 |
|---|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Type | General-purpose precision operational amplifier | LT1007-family precision operational amplifier | LT1007-family precision operational amplifier | Low-noise, high-speed, precision operational amplifier |
| Number of Amplifiers | 1 amplifier | 1 amplifier | 1 amplifier | 1 amplifier |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole |
主要差異化特點
- Low-noise precision operation (對比LT1007)
- High rejection of common-mode and supply disturbances (對比LT1007CN8#PBF)
- Speed capability within a precision amplifier family (對比LT1007ACN8#PBF)
設計說明
Route the differential input and feedback connections as short and compact as practical, especially because the LT1007 family combines high bandwidth with low-noise precision requirements. Keep high-impedance input nodes away from supply, clock, and switching paths. The 8-pin PDIP layout should follow the manufacturer package drawing, including pin-1 orientation, and local supply decoupling should be placed close to the relevant supply pins.
Choose the feedback network for the exact gain and stability configuration. The manufacturer data describes a decompensated LT1037 version with a 60 MHz gain-bandwidth product and a minimum 11 V/us slew rate, but the LT1007ACP ordering option must be checked against the datasheet before applying those values. Avoid assuming that a conventional unity-gain compensation network is appropriate for every family member.
Do not use the family-level 60 MHz bandwidth or 11 V/us slew-rate figures without confirming that they apply to the exact LT1007ACP version. Also verify the supply range, input common-mode range, output swing, load capability, and operating temperature from the electrical characteristics table. These checks matter because a small ordering-suffix or grade difference can change the valid design envelope.
For microvolt-level signal paths, use a defined ground return, minimize leakage through board insulation, and keep high-impedance nodes away from contaminated or damp surfaces. Short feedback loops and local bypassing reduce the chance that switching energy or ground gradients will dominate the amplifier noise floor. These practices are especially important when the circuit operates near the 60 nV peak-to-peak input-noise figure quoted for the 10 Hz region.
合規資訊
Compliance status is not stated in the available product snippets. Verify RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification requirements for the exact manufacturer lot and package before procurement.