LT1884IS8 - Dual Picoamp Precision Op Amp | Analog Devices
MPN: LT1884IS8 ✓ 啟用中LT1884IS8 概覽
An operational amplifier is a high-gain differential amplifier used to amplify, buffer, filter, or compare small voltage signals. The LT1884 belongs to the precision operational amplifier category, combining low input bias current with low offset voltage and temperature-stable performance. This makes it especially useful when the measured or controlled signal is sourced from a high-impedance sensor or another circuit whose input current must not materially disturb the signal.
The key input specifications are an input offset voltage trimmed to less than 50 uV, an input bias current rated to a maximum of 400 pA, and rail-to-rail output operation. The LT1884IS8 is a dual amplifier, allowing two independent signal paths in one package. Its 8-lead SOIC construction supports conventional surface-mount assembly while preserving access to both amplifier channels.
The LT1884 and LT1885 family is positioned for precision applications requiring accurate input behavior and an output that can approach the supply rails. Picoamp input bias current reduces loading of high-impedance sources, while trimmed offset voltage improves DC accuracy. These characteristics are more important than merely maximizing open-loop gain in instrumentation, sensor-conditioning, and low-current measurement systems.
Typical uses include precision sensor interfaces, photodiode-related signal conditioning, battery monitoring, laboratory instrumentation, and low-current feedback networks. The dual configuration can implement two amplifier functions in one package, such as a non-inverting input stage followed by a filtering or output-conditioning stage.
Designers should verify input and output common-mode limits, supply range, stability with the selected feedback network, and decoupling requirements in the LT1884 datasheet. Because input bias current is a central feature, board cleanliness, leakage from PCB contamination, and guard-ring techniques may be as important as the nominal amplifier accuracy.
This page combines manufacturer specifications, practical circuit guidance, application fit, and same-package drop-in alternatives. It also highlights the temperature-grade and family differences that should be checked before replacing the LT1884IS8 in an existing 8-lead SOIC layout.
直接替換替代品,適用於 LT1884IS8 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LT1884IS8 (相同外形與佔位) — 差異在於 Amplifier Type, Input Offset Voltage, Mounting Type, Output Swing, Package.
LT1884CS8
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LT1884ES8
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LT1885IS8
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LT1885CS8
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LT1885ES8
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LT1884IS8 最大額定值與電氣特性
| Amplifier Type | Dual precision operational amplifier |
| Number of Circuits | 2 circuits |
| Output Swing | Rail-to-rail |
| Input Offset Voltage | Less than 50 uV |
| Input Bias Current | 400 pA maximum |
| 封裝 | 8-lead SOIC |
| 安裝類型 | Surface mount |
| Product Type | General-purpose precision amplifier |
LT1884IS8 8-lead soic 腳位配置指南
LT1884IS8(8-lead soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LT1884IS8.
請參閱 資料表 以查看完整腳位配置。
典型應用
LT1884IS8 適用於 6 應用s: High-Impedance Sensor Signal Conditioning, Photodiode and Optical-Signal Measurement, Precision Voltage and Current Monitoring, Laboratory Instrumentation Front Ends, Battery and Wearable-Sensor Interfaces, Industrial Low-Level Control Loops.
High-Impedance Sensor Signal Conditioning
The LT1884IS8 fits high-impedance sensor front ends because its input bias current is specified to a maximum of 400 pA, reducing the disturbance that a conventional amplifier can place on a sensitive source. Its input offset voltage is trimmed below 50 uV, which supports accurate amplification of small sensor-generated voltages. Place the amplifier close to the sensor, keep high-impedance traces short, and use guarding when board leakage could compete with the picoamp input current. The dual package can provide gain in one channel and filtering or level conditioning in the other.
推薦
Photodiode and Optical-Signal Measurement
The LT1884IS8 is appropriate for photodiode and optical-signal measurement circuits where the source impedance can be high and input bias current must remain small. Its 400 pA maximum bias current limits amplifier-generated error relative to the measured photocurrent, while the trimmed offset voltage below 50 uV supports low-level DC accuracy. The rail-to-rail output helps maximize usable output range in compact single-supply systems. Dark current, diode leakage, surface contamination, and guard-ring design must be evaluated separately because they can exceed the amplifier's bias current.
推薦
Precision Voltage and Current Monitoring
The LT1884IS8 supports precision voltage monitoring and low-current measurement when the circuit requires both low loading and accurate DC behavior. Input offset below 50 uV limits static voltage error, and the picoamp input-current class helps preserve measurement integrity at high source impedance. One channel can amplify the monitored voltage while the other provides filtering, gain, or a comparator-like conditioning function. Resistor thermal noise, input bias-current error through feedback resistors, common-mode headroom, and output-current limits remain important design constraints.
推薦
Laboratory Instrumentation Front Ends
The LT1884IS8 is useful in laboratory instrumentation front ends that amplify small signals without imposing substantial current on the source. Its maximum input bias current of 400 pA and offset voltage below 50 uV provide a strong starting point for precision measurement paths, while rail-to-rail output improves headroom in portable instruments. The 8-lead SOIC allows two amplifier channels to share one package. Design the feedback network for the intended closed-loop gain, verify stability across the required capacitive load, and use clean PCB practices to avoid leakage-related errors.
推薦
Battery and Wearable-Sensor Interfaces
The LT1884IS8 can serve as the analog front end for battery-powered sensor interfaces where every microamp of input current can affect battery life or sensor integrity. The 400 pA maximum input bias current reduces amplifier loading, while rail-to-rail output is valuable in compact low-voltage systems where excess output headroom is limited. Two channels can monitor a sensor and condition a reference or filter another signal. The complete design must still verify supply range, output swing at the selected load, shutdown strategy, and the leakage characteristics of the sensor and PCB.
推薦
Industrial Low-Level Control Loops
The LT1884IS8 can be used in industrial control and feedback circuits that amplify low-level error signals near a feedback sensor. Picoamp input bias reduces loading on high-impedance sensing nodes, and trimmed offset below 50 uV improves the accuracy of small control corrections. The dual configuration can combine sensing and drive functions while maintaining a compact 8-lead SOIC footprint. Industrial use requires checking the selected temperature grade, supply-noise behavior, output drive, stability, and separation between sensitive input routes and switching or power-conversion nodes.
推薦
推薦產品摘要
工程參考資料,適用於 LT1884IS8 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LT1884CS8 | LT1884ES8 | LT1885IS8 | LT1885CS8 | LT1885ES8 |
|---|---|---|---|---|---|---|
| Package | 8-lead SOIC | 8-lead SOIC | 8-lead SOIC | 8-lead SOIC | 8-lead SOIC | 8-lead SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Amplifier Count | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Temperature Grade | Industrial, -40 to 85 C | Commercial, 0 to 70 C | Extended, -40 to 125 C | Industrial, -40 to 85 C | Commercial, 0 to 70 C | Extended, -40 to 125 C |
| Family | LT1884 | LT1884 | LT1884 | LT1885 | LT1885 | LT1885 |
主要差異化特點
- Very low input bias current for precision signal conditioning (對比LT1885IS8)
- Rail-to-rail output improves low-voltage signal range (對比LT1884CS8)
- Dual precision amplifier in a compact 8-lead SOIC (對比LT1884ES8)
- Trimmed low-offset option for DC-sensitive measurements (對比LT1885CS8)
設計說明
Treat the LT1884IS8 input as a picoamp-class node. Keep input traces short, avoid running them beside switching or high-impedance leakage paths, and use a grounded guard around sensitive input copper when board contamination could produce leakage comparable to the 400 pA maximum bias current. Clean the assembled PCB and consider guarding the feedback-resistor junction so environmental leakage does not dominate the measurement.
Do not assume that rail-to-rail output means the output can reach either supply rail under every load. Check the manufacturer output-swing curves, load current, output-capacitance limits, and gain configuration for the actual circuit. Likewise, verify input common-mode range at both amplifier channels because exceeding that range can cause input-stage saturation or recovery problems that are not apparent from a nominal rail-to-rail specification.
Place the amplifier, feedback components, and any input filtering close to the source and away from switching nodes. Use a compact ground-return strategy so input currents do not share copper paths with load currents. If the feedback resistor is very large, its thermal noise may dominate, and if the source impedance is very high, resistor dielectric or PCB leakage can exceed the amplifier's input bias current. Calculate the error budget before selecting extreme values.
Place the manufacturer's recommended bypass capacitor close to the supply pins and provide adequate routing area for transient current. Confirm the selected supply voltage against the device's operating range and output-swing curves rather than relying on the nominal supply label. In low-power systems, include quiescent current and leakage from the surrounding circuit in the complete power budget, since sensor-path error can matter before the amplifier's own supply current is considered.
合規資訊
Compliance attributes were not identified in the product information. AEC-Q100 is not applicable because the LT1884 is a general-purpose precision operational amplifier rather than an automotive-qualified device.