MCF5472VR200 - 32-Bit ColdFire V4E MPU 200MHz | NXP | 388-PBGA
MPN： MCF5472VR200 ✗ 停產MCF5472VR200 概覽
A microprocessor unit (MPU) is a CPU-centric system-on-chip tailored for control-plane workloads where deterministic response, rich connectivity, and external memory expansion matter more than on-chip flash. Within the broader taxonomy, the MCF5472VR200 is a ColdFire V4E MPU, a member of the Freescale/NXP 68k-derived ColdFire family, sitting under the ColdFire V4 generation, the MPU class, and ultimately the embedded microprocessor category of semiconductors. Compared with microcontroller units (MCUs), MPUs like the MCF5472VR200 rely on external SDRAM/Flash and typically drive operating systems or large RTOS workloads.
Key specifications include 200 MHz maximum core clock (delivering 295+ MIPS Dhrystone equivalent at the V4e pipeline), 32 KB internal SRAM, integrated FPU for IEEE-754 single-precision floating point, MMU for virtual memory and protected-mode operating systems, dual 10/100 Ethernet MACs, a 32-bit PCI 2.1 interface, USB, four UARTs, two I2C buses, two SSI/SPI ports, and an on-chip encryption accelerator. Operating supply voltages are 1.5 V core and 3.3 V I/O.
Typical applications include industrial control with secure Ethernet connectivity, factory automation PLCs, networked motion controllers, secure gateways, and high-end embedded HMI controllers. The encryption accelerator and dual Ethernet make the part particularly well-suited for industrial protocols requiring both real-time and secure communication.
When designing with this device, ensure the PCB provides adequate thermal dissipation for the 27x27 mm PBGA and that 1.5 V core and 3.3 V I/O rails are sequenced within the datasheet-specified window. The part is pin-compatible with the MCF548x family for migration paths.
This page synthesizes distributor pricing, lifecycle status, drop-in same-package alternatives, and practical design notes that are not consolidated in the manufacturer datasheet alone.
直接替換替代品，適用於 MCF5472VR200 — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： MCF5472VR200 （相同外形與佔位） — 差異在於 Encryption Accelerator, Package, FPU, Core Architecture, RoHS Status.
MCF5485CVR200
✅ 直接替換聯絡詢價
查看資料表 →MCF5485CZP200
✅ 直接替換📋 參考替代品（不在目錄中）
MCF5475VR200
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →MCF5474VR200
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →MCF5471VR200
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →MCF5472VR200 最大額定值與電氣特性
| Core Architecture | ColdFire V4E (limited superscalar) |
| Maximum Core Frequency | 200 MHz |
| 工作電源電壓 | 1.5 V (core), 3.3 V (I/O) |
| Internal SRAM | 32 KB |
| On-chip Flash | ROMless |
| MMU | Yes |
| FPU | Yes (IEEE-754 single precision) |
| Encryption Accelerator | Yes |
| Ethernet MAC | 2 x 10/100 Mbps |
| PCI Interface | 32-bit PCI 2.1 |
| UART | 4 |
| I2C | 2 |
| SSI/SPI | 2 |
| 封裝 | 388-PBGA (27x27 mm) |
| 安裝類型 | Surface Mount |
| RoHS 狀態 | Compliant (per distributor data) |
MCF5472VR200 388-pbga (27x27 mm) 腳位配置指南
MCF5472VR200（388-pbga (27x27 mm) 封裝）的腳位配置。 此數位 IC 包含 GPIO、通訊介面（UART、SPI、I2C）與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料： MCF5472VR200.
請參閱 資料表 以查看完整腳位配置。
典型應用
MCF5472VR200 適用於 6 應用s: Industrial Secure Gateway, Factory Automation PLC Controller, Networked Motion Controller, Secure Connected HMI Controller, Networked Medical Instrumentation, Industrial Printer / Imaging Controller.
Industrial Secure Gateway
The MCF5472VR200's dual 10/100 Ethernet MACs and on-chip encryption accelerator make it a strong fit for industrial secure gateway designs that bridge fieldbus networks to enterprise IT. Running uCLinux or an RTOS, it terminates two physical network segments while performing AES/DES for traffic authentication. The 200 MHz ColdFire V4E core delivers sufficient throughput for firewall and VPN gateway workloads in factory environments, while the 388-PBGA provides the pin count required to expose both MII/RMII interfaces alongside PCI for expansion. Estimated: at 200 MHz the core sustains 295 MIPS, which is enough headroom for typical stateful packet inspection plus encryption offload. The part's NRND status should be weighed against long product life cycles; the pin-compatible MCF5485CVR200 is a future-proof upgrade path.
推薦
Factory Automation PLC Controller
The MCF5472VR200 fits PLC controller designs that demand deterministic real-time response plus Ethernet/IP, Modbus TCP, or Profinet connectivity. The ColdFire V4E core's deterministic interrupt latency, combined with dual Ethernet for redundant ring topologies, supports industrial automation standards. The MMU enables protected-mode operating systems for safe multi-tasking of scan loops, motion control, and HMI tasks. The 1.5 V core / 3.3 V I/O split simplifies power tree design when paired with standard 3.3 V logic and SDRAM. Estimated: external 32-bit SDRAM (typically 64-128 MB) is required because the part is ROMless. Designers should plan for industrial temperature grades (-40C to +85C) and confirm the specific variant ordering code supports that range.
推薦
Networked Motion Controller
For multi-axis motion controllers communicating over EtherCAT, SERCOS, or standard Ethernet, the MCF5472VR200 provides a balance of deterministic performance and connectivity. The hardware FPU accelerates real-time kinematic computations for 4- or 8-axis machines, while the dual Ethernet ports support ring or star topologies common in motion systems. The ColdFire V4e pipeline issues up to two instructions per cycle, which is sufficient for closed-loop PID rates of 8-32 kHz across multiple axes. Estimated: a single 200 MHz core can sustain 4 axes at 16 kHz update rate with margin for trajectory planning. The PCI bus allows expansion with dedicated motion daughtercards when higher axis counts are required.
推薦
Secure Connected HMI Controller
Operator panel and HMI designs benefit from the MCF5472VR200's MMU-protected Linux support, hardware FPU for graphics primitives, and encryption accelerator for authenticated user sessions. The 32-bit PCI bus enables connection of LCD controller ASICs or external graphics chips, while the four UARTs support legacy RS-485/RS-232 industrial peripherals. The part's MMU enables full virtual memory, which is essential for running Qt/Embedded or WebKit-based HMI frameworks with process isolation. Estimated: 32 KB on-chip SRAM is small for HMI stacks; external SDRAM is required. Power dissipation is dominated by core switching at 200 MHz, so adequate PCB thermal relief is needed on the 27x27 mm PBGA.
推薦
Networked Medical Instrumentation
The MCF5472VR200 supports networked medical instrumentation such as patient monitors, infusion pumps with central station connectivity, and diagnostic analyzers that require deterministic response plus secure DICOM/HL7 data exchange. The on-chip encryption accelerator secures PHI traffic over Ethernet without taxing the CPU, while the hardware FPU accelerates signal-processing math for vital-signs algorithms. The 388-PBGA package supports the parallel external bus needed to interface medical-grade ADC front-ends via PCI or external glue logic. Estimated: medical designs typically pair the MPU with an external watchdog and brown-out supervisor; the part's NRND status requires a lifecycle mitigation plan, often migrating to a pin-compatible MCF548x variant.
推薦
Industrial Printer / Imaging Controller
Print engines and imaging controllers use the MCF5472VR200's MMU for high-level page-rendering pipelines, hardware FPU for color-space conversions, and dual Ethernet for in-line production network integration. The PCI bus supports direct attachment of image-acquisition ASICs or FPGA-based scanners, while the four UARTs drive legacy RS-232 service interfaces. The 200 MHz ColdFire V4e is sufficient for moderate page-render rates at 600 dpi; higher throughput designs benefit from the MCF5485CVR200 upgrade. Estimated: external SDRAM of 64 MB or more is typical for full-page buffers. Designers should budget PCB area for the 27x27 mm PBGA and ensure the 1.5 V core rail is sequenced properly against 3.3 V I/O.
推薦
推薦產品摘要
工程參考資料，適用於 MCF5472VR200 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCF5485CVR200 | MCF5485CZP200 | MCF5475VR200 | MCF5474VR200 |
|---|---|---|---|---|---|
| Package | 388-PBGA (27x27 mm) | 388-PBGA (27x27 mm) - same | 388-PBGA (27x27 mm) - same | 388-PBGA (27x27 mm) - same | 388-PBGA (27x27 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Architecture | ColdFire V4E | ColdFire V4E | ColdFire V4E | ColdFire V4E | ColdFire V4E |
| Maximum Core Frequency | 200 MHz | 200 MHz (higher ceiling) | 200 MHz | 200 MHz | 200 MHz |
| Internal SRAM | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| Ethernet MAC | 2 x 10/100 Mbps | 2 x 10/100 Mbps | 2 x 10/100 Mbps | 2 x 10/100 Mbps | 1 x 10/100 Mbps |
| Lifecycle Status | NRND | NRND | NRND | NRND | NRND |
| RoHS Compliance | Compliant | Compliant | Compliant | Compliant | Compliant |
主要差異化特點
- Pin-compatible upgrade path within NXP ColdFire V4E family (對比MCF5485CVR200)
- Industrial temperature variant available in same footprint (對比MCF5485CZP200)
- MMU + FPU combination supports protected-mode operating systems (對比MCF51AC128ACFUE)
設計說明
The MCF5472VR200 requires a 1.5 V core rail and a 3.3 V I/O rail. The core rail must not exceed the I/O rail during power-up to prevent latch-up; design the power sequencer or use a tracking regulator to enforce this. Estimated: with a 200 MHz switching core, the 1.5 V rail typically draws 400-600 mA depending on activity, so budget 1 A headroom on the regulator.
The 27x27 mm 388-PBGA package dissipates heat primarily through the internal ball grid and PCB copper. Place a thermal via array directly under the package center on inner PCB layers to conduct heat to the bottom-side copper pour. Estimated: full-load core power dissipation is approximately 1.0-1.3 W at 200 MHz with 1.5 V supply; without thermal vias the junction-to-ambient thermal resistance rises and may force derating in enclosed industrial enclosures.
Route the external memory bus (address, data, control) with matched length traces and 50 ohm controlled impedance. Place SDRAM as close as possible to the BGA to minimize stub lengths and signal integrity issues. Provide solid ground planes on layers 2 and 4 directly under the BGA, with stitched ground vias around signal via fields to maintain return-path continuity for high-speed signals like Ethernet MII and PCI.
Do not assume the boot mode configuration is preserved across resets without proper reset circuit design. The MCF5472VR200 samples boot mode pins on the rising edge of RESET; ensure the mode signals are stable for at least 4 clock cycles before RESET deassertion. A common pitfall is floating mode pins or excessive capacitance that prevents clean sampling, which can result in unbootable designs.
合規資訊
RoHS compliance per distributor listings. REACH, halogen-free, and conflict-mineral declarations are not present in the verified web data; set to unknown pending manufacturer statement.
