MCP3426A0-E/MC - 16-Bit Dual-Channel ADC | Microchip Technology
MPN: MCP3426A0-E/MC ✓ 啟用中MCP3426A0-E/MC 概覽
A delta-sigma ADC is a voltage-to-digital conversion IC that averages successive samples and applies digital filtering to produce a high-resolution result from low-frequency analog signals. The MCP3426 belongs to the broader hierarchy of data-converter ICs, analog-to-digital converters, signal-chain semiconductors, and general-purpose mixed-signal devices. Its differential architecture is especially useful when the source has a small differential signal riding on a larger common-mode voltage.
The device provides up to 16 bits of resolution, two differential input channels, a 2.048 V internal reference, and an I2C-compatible interface. The A0 device designation identifies the specific gain and conversion-timing configuration within the MCP3426 family. Operation from a single supply of 2.7 V to 5.5 V allows the converter to operate from common 3.3 V and 5 V systems. The low-noise conversion architecture is appropriate for precision measurement rather than high-speed waveform acquisition.
Delta-sigma conversion favors low-frequency signals because its digital filter improves noise performance but limits effective sampling bandwidth. The MCP3426 family is designed around continuous conversion, where internal oversampling and filtering determine output speed and noise. Differential inputs reduce sensitivity to common-mode disturbances when the source impedance at both inputs is closely matched. The internal reference simplifies ratiometric or absolute measurements by removing the need for an external reference circuit in many applications.
Typical uses include current sensing, temperature measurement, bridge-transducer instrumentation, pressure monitoring, and low-level voltage acquisition. The onboard reference and differential inputs are particularly useful when a sensor produces a small voltage across a shunt or bridge. Because the MCP3426 is not intended for high-frequency signal capture, applications requiring kilohertz or megahertz bandwidth should use a faster converter architecture.
For PCB implementation, place input, reference, and bypass capacitors close to their associated pins and route the two differential inputs as a compact, balanced pair. Keep the exposed pad connected to the ground plane and follow the manufacturer’s land-pattern and thermal-via guidance. Confirm the programmed conversion rate, gain, and output-code interpretation against the MCP3426/7/8 datasheet before scaling the analog input.
This product page combines the manufacturer’s electrical specifications, package and interface details, family-level alternatives, and practical design guidance. It also distinguishes the MCP3426A0-E/MC from conversions that use different package formats or faster ADC architectures, helping engineers confirm drop-in suitability before redesigning an analog measurement board.
直接替換替代品,適用於 MCP3426A0-E/MC — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
MCP3426A0T-E/MC
✅ 直接替換📋 參考替代品(不在目錄中)
MCP3426A0-E/MC 最大額定值與電氣特性
| 解析度 | 16 bit |
| Number of Input Channels | 2 channels |
| Input Architecture | Differential |
| ADC Architecture | Delta-sigma |
| Conversion Rate | 15 samples/s |
| Internal Reference Voltage | 2.048 V |
| Differential Input Range | ±2.048 V |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Digital Interface | I2C-compatible, 2-wire serial |
| 封裝 | 8-DFN, 2 x 3 mm, exposed pad |
| 腳位數 | 8 pins |
| 安裝類型 | Surface mount |
| Packaging | Tube |
| 工作溫度 | -40°C to +125°C |
| RoHS 狀態 | Compliant |
| 生命週期狀態 | Active |
| ECCN | EAR99 |
MCP3426A0-E/MC 8-dfn, 2 x 3 mm, exposed pad 腳位配置指南
MCP3426A0-E/MC(8-dfn, 2 x 3 mm, exposed pad 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: MCP3426A0-E/MC.
請參閱 資料表 以查看完整腳位配置。
典型應用
MCP3426A0-E/MC 適用於 6 應用s: Precision Current Sensing, Temperature and Resistance Sensing, Bridge Transducer Measurement, Battery and Power Rail Monitoring, Industrial Process Sensing, Environmental and IoT Sensing.
Precision Current Sensing
The MCP3426A0-E/MC suits low-frequency current measurement when a shunt amplifier develops a small differential voltage across a precision sense resistor. Its 16-bit resolution and two differential inputs preserve the polarity and magnitude of the measured voltage while rejecting much of the common-mode signal present at the shunt amplifier output. The 2.048 V onboard reference provides a defined conversion basis, and the 15-sample-per-second rate is appropriate for load monitoring, power-loss recording, and laboratory current logging. The amplifier must keep its outputs within the converter’s gain-dependent common-mode limits, and the PCB should route the differential pair symmetrically to minimize conversion error.
推薦
Temperature and Resistance Sensing
The MCP3426A0-E/MC can digitize slow temperature or resistance measurements from RTDs, thermistors, or resistive bridges without the conversion speed of a high-rate SAR ADC. Its two differential channels support paired sensing or redundant probes, while the 16-bit resolution improves sensitivity to small resistance changes and therefore reduces excitation-related measurement error. The onboard 2.048 V reference supports stable absolute readings when the application does not require ratiometric tracking. A 15-sample-per-second output rate is well matched to thermal time constants, and input filtering can suppress switching-supply ripple without exceeding the converter’s usable bandwidth.
推薦
Bridge Transducer Measurement
The MCP3426A0-E/MC is appropriate for strain, pressure, and force bridges that generate a small differential output around a common-mode voltage. Differential inputs reject shared disturbances more effectively than a single-ended converter, and the 2.048 V internal reference simplifies excitation and conversion alignment in many compact sensor modules. The device’s low-noise delta-sigma architecture favors slow but precise measurements, where mechanical response limits the useful bandwidth well below the converter’s 15-sample-per-second conversion rate. Designers should verify bridge excitation requirements, input common-mode limits, and gain selection in the MCP3426/7/8 datasheet before adding an instrumentation front end.
推薦
Battery and Power Rail Monitoring
The MCP3426A0-E/MC can monitor slow battery, supply, or energy-storage voltages where accuracy at a 15-sample-per-second rate is more valuable than waveform capture. Two differential channels allow measurement of a balanced differential rail or paired sensing points, while the 2.048 V reference establishes a stable conversion scale. The single-supply operation from 2.7 V to 5.5 V supports embedded monitoring circuits that already operate from common system rails. Input dividers or differential amplifiers should include protection appropriate to the monitored source, and the converter should remain within its common-mode range throughout charging, load transients, and end-of-discharge conditions.
推薦
Industrial Process Sensing
The MCP3426A0-E/MC fits slow industrial process measurements such as valve position, tank level, pressure, and environmental analog sensors. Its 16-bit resolution supports fine measurement resolution, while the differential inputs can reduce sensitivity to offset and disturbance when paired with properly matched sensor circuitry. The I2C-compatible interface allows a controller to retrieve compact conversion results without occupying a parallel data bus, and the 15-sample-per-second rate is adequate for many thermal and mechanical processes. For reliable deployment, protect the inputs from industrial transients, maintain matched routing, and verify that the measurement bandwidth does not exceed the delta-sigma filter’s useful response.
推薦
Environmental and IoT Sensing
The MCP3426A0-E/MC is suitable for compact IoT sensing nodes that monitor a slow analog quantity from a resistive sensor or low-level transducer. Its low-noise delta-sigma conversion avoids the power and complexity associated with continuously running a high-speed converter, while the 2.048 V onboard reference reduces the external component count. The dual-channel differential format can reduce wiring requirements when each sensor is referenced to a common return. Because the converter operates at only 15 samples per second, firmware can sleep between conversions for low-power sensing. Product designers should account for the common-mode range, analog settling, I2C pull-up requirements, and exposed-pad grounding in compact enclosures.
推薦
推薦產品摘要
工程參考資料,適用於 MCP3426A0-E/MC — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP3426A0T-E/MC |
|---|---|---|
| Package | 8-DFN (2x3 mm, exposed pad) | 8-DFN (2x3 mm, exposed pad) |
| Brand | Microchip Technology | Microchip Technology |
| Resolution | 16 bit | 16 bit |
| Input Channels | 2 differential channels | 2 differential channels |
| Conversion Rate | 15 samples/s | 15 samples/s |
| Internal Reference | 2.048 V | 2.048 V |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Digital Interface | I2C-compatible, 2-wire serial | I2C-compatible, 2-wire serial |
| Device Designation | MCP3426A0 | MCP3426A0T |
主要差異化特點
- High resolution in a compact converter package (對比MCP3426A0T-E/MC)
- Integrated precision reference (對比MCP3426A0T-E/MC)
- Low-power measurement conversion rate (對比MCP3426A0T-E/MC)
- Single-supply compatibility (對比MCP3426A0T-E/MC)
設計說明
Route the two differential inputs as a compact, approximately matched pair and keep them away from switching nodes and high-current return paths. Place the input and bypass capacitors at the converter pins with short ground returns. The manufacturer’s package drawing and layout guidance should be followed for the 8-DFN exposed pad, including adequate thermal-via coverage and unobstructed copper beneath the pad.
Do not treat the MCP3426A0-E/MC as a general-purpose high-speed ADC. Its 15-sample-per-second conversion rate is optimized for low-frequency measurements, and excessive signal bandwidth or slow analog settling can distort results. Confirm the selected gain, conversion timing, common-mode limits, and input-voltage range in the MCP3426/7/8 datasheet before applying a transducer with large excursions or high source impedance.
Place the supply bypass capacitor immediately beside VDD and use the shortest possible connection to the ground plane. Keep analog return current separate from noisy digital or switching currents where the board layout permits. Because the converter derives its conversion accuracy from the supply and internal reference, stabilizing VDD reduces error that could otherwise be mistaken for a sensor or gain problem.
Match the impedances presented by both differential inputs so their common-mode behavior remains balanced. If the source is high impedance, verify that the selected gain and conversion interval allow sufficient acquisition time for the internal sampling capacitors to charge. An RC anti-alias network should be chosen using the device bandwidth and conversion rate rather than added by arbitrary capacitor values.
合規資訊
RoHS-compliant status and EAR99 classification are listed for MCP3426A0-E/MC. Qualification, lead-free, halogen-free, REACH, and conflict-minerals status require confirmation for the exact production ordering code.