MSP430F2410TPM - 16MHz 56KB Flash MCU | Texas Instruments
MPN: MSP430F2410TPM ✓ 啟用中MSP430F2410TPM 概覽
An ultra-low-power microcontroller is a semiconductor controller designed to minimize energy consumption during active operation and standby periods. The MSP430 architecture combines a 16-bit RISC CPU, 16-bit registers, constant generators, and multiple low-power operating modes. This places the device in the MCU hierarchy as a general-purpose embedded controller designed for battery-powered sensing, instrumentation, and control systems.
Principal features include a maximum 16 MHz clock, hardware multiplier, two 16-bit timers, a fast 12-bit analog-to-digital converter, and a comparator. Two universal serial communication interface modules support I2C, SPI, and UART configurations. The 56 KB Flash area provides embedded program storage, while 4 KB of SRAM supports stack, variables, buffers, and intermediate processing.
The mixed-signal architecture allows the MCU to control digital logic while measuring analog inputs through the ADC12 and comparator blocks. Two independent 16-bit timers support periodic timing, capture, compare, and PWM generation. The hardware multiplier accelerates multiply and multiply-accumulate operations, while the MSP430 instruction set and constant generators improve code density for control and instrumentation workloads.
Typical applications include industrial sensor acquisition, portable measurement instruments, low-power energy-monitoring equipment, building controls, and compact embedded systems that require several serial interfaces. The 10 mm by 10 mm LQFP footprint is also suitable for densely populated control boards requiring numerous mixed-signal and digital functions in one device.
Designers should plan decoupling close to the supply pins, route analog inputs away from high-current switching nodes, and use the ADC and comparator inputs according to the manufacturer pin and layout guidance. Firmware should enable the appropriate clock source, configure unused peripherals for low leakage, and use the device's low-power modes only after validating wake-up timing and retained state.
This product page combines the MSP430F2410TPM specifications with package, application, and drop-in replacement guidance. It also highlights design trade-offs among same-package MSP430F2xx devices, helping engineers select the appropriate memory, serial-interface, and analog configuration without changing the PCB footprint.
直接替換替代品,適用於 MSP430F2410TPM — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MSP430F2410TPM (相同外形與佔位) — 差異在於 ADC Resolution, Flash Memory, SRAM, Supply Voltage, CPU Architecture.
MSP430F2471TPM
✅ 直接替換📋 參考替代品(不在目錄中)
MSP430F247TPM
✅ 直接替換聯絡詢價
查看資料表 →MSP430F249TPM
✅ 直接替換聯絡詢價
查看資料表 →MSP430F2411TPM
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MSP430F2412TPM
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MSP430F2410TPM 最大額定值與電氣特性
| CPU Architecture | 16-bit MSP430 RISC |
| 最大時脈頻率 | 16 MHz |
| Flash Memory | 56 KB |
| Additional Flash Region | 256 bytes |
| SRAM | 4 KB |
| ADC Resolution | 12 bits |
| ADC Type | Fast 12-bit ADC12 |
| Analog Comparator | 1 comparator |
| Timers | 2 x 16-bit timers |
| Universal Serial Communication Interfaces | 2 USCI modules |
| Supported Serial Protocols | I2C, SPI, UART |
| Hardware Multiplier | 1 hardware multiplier |
| Maximum I/O Pins | Up to 48 GPIO pins |
| 供應電壓 | 3 V |
| 封裝 | 64-LQFP, 10 mm x 10 mm |
| 安裝類型 | Surface mount |
MSP430F2410TPM 64-lqfp, 10 mm x 10 mm 腳位配置指南
MSP430F2410TPM(64-lqfp, 10 mm x 10 mm 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: MSP430F2410TPM.
請參閱 資料表 以查看完整腳位配置。
典型應用
MSP430F2410TPM 適用於 6 應用s: Industrial Sensor Acquisition, Portable Measurement Instrument, Building and Environmental Control, Battery-Powered Data Logger, Motor and Actuator Control, Communications and Protocol Bridge.
Industrial Sensor Acquisition
The MSP430F2410TPM fits industrial sensor modules that combine analog measurement with local control and serial reporting. Its 12-bit ADC measures sensor inputs, while the comparator supports threshold detection and direct comparisons without continuous CPU polling. Two 16-bit timers provide periodic sampling, capture, and PWM timing, and the 16 MHz CPU can filter or scale measurements before transmission. With 56 KB Flash and 4 KB SRAM, the device also has practical room for calibration tables, buffers, and communication routines. Use the I2C or SPI interface for external sensors and UART for field updates, while placing analog inputs and the MCU supply on a quiet, decoupled section of the board.
推薦
Portable Measurement Instrument
The MSP430F2410TPM is appropriate for portable meters and compact analyzers that need low standby power alongside deterministic control. The 16 MHz MSP430 CPU supports digital filtering and calibration, the 12-bit ADC handles process or sensor voltage measurements, and the comparator can implement threshold alarms. The 56 KB Flash stores firmware and calibration information, while 4 KB SRAM supports sample buffers. Two USCI modules allow simultaneous connection to a sensor bus and a host interface. During inactive intervals, the MCU can enter a low-power mode and retain state, extending battery life between measurements. Validate the wake-up latency and analog settling behavior against the required measurement cycle.
推薦
Building and Environmental Control
The MSP430F2410TPM can serve as the mixed-signal controller in a building control node that supervises temperature, light, occupancy, or actuator feedback. The ADC12 samples analog sensors, and the comparator provides a fast threshold function for discrete warnings. Two timers can generate control intervals or PWM outputs, while I2C is suitable for environmental sensors and SPI for local storage or display peripherals. The MSP430's low-power operating modes help limit energy use in rooms that are sparsely occupied. UART can support configuration and diagnostic traffic. Select pin multiplexing carefully because alternate USCI functions and ADC channels can overlap, and confirm that the chosen firmware keeps analog and digital return paths separated.
推薦
Battery-Powered Data Logger
The MSP430F2410TPM is well suited to periodic battery-powered logging because it combines a fast 16 MHz MCU with low-power modes, a 12-bit ADC, and 56 KB of program Flash. A timer can wake the device at defined intervals, acquire sensor data, store or transmit results through SPI, I2C, or UART, and return to a low-energy state. The 4 KB SRAM can buffer samples during a measurement burst, while the hardware multiplier assists with scaling and filtering operations. Keep the active interval short to reduce average energy use, and disable unused analog and communication blocks. Validate wake-up timing, sensor-settling requirements, and write endurance for nonvolatile data storage before finalizing the power budget.
推薦
Motor and Actuator Control
The MSP430F2410TPM can supervise low-power motor, valve, or actuator systems where a dedicated timer subsystem is valuable. Two 16-bit timers support periodic control, input capture, and PWM generation, while the 16-bit RISC CPU performs position logic, fault handling, and communication. The comparator can monitor a feedback threshold, and the ADC12 can supervise an analog sensor or current-related voltage. Its mixed-signal integration reduces the need for separate logic in compact modules. For inductive or switching loads, isolate the MCU from high-current edges with appropriate drive circuitry, filtering, and grounding rather than relying on the MCU pins for direct load handling. Firmware should include defined disable states for startup and fault conditions.
推薦
Communications and Protocol Bridge
The MSP430F2410TPM can implement a compact protocol bridge when a system must combine a local serial device with a secondary embedded interface. Two USCI modules support I2C, SPI, and UART, permitting one port to connect to a sensor or transceiver while another handles a host or peripheral link. The 16 MHz CPU provides enough throughput for framing, checksum, buffering, and basic protocol conversion, while 56 KB Flash and 4 KB SRAM support firmware and working buffers. Use a timer for baud-rate generation, timeouts, or periodic status reporting. Choose the serial pin routes from the device multiplexing tables, isolate long cables with appropriate protection, and test all bus idle levels and timing margins under the maximum bus loading.
推薦
推薦產品摘要
工程參考資料,適用於 MSP430F2410TPM — 比較、設計指引及合規資訊。
選型指南
Consider MSP430F2471TPM, MSP430F247TPM, or MSP430F249TPM when their additional family resources are useful and their exact memory, ADC, and USCI configurations satisfy the design. MSP430F2411TPM and MSP430F2412TPM are same-package options where their ADC12 implementation is appropriate. All listed candidates require validation of pin multiplexing, clock setup, startup code, peripheral availability, and errata. No verified cross-manufacturer drop-in was identified, so a foreign MCU should not be treated as a footprint-only substitution.
與替代品比較
| 參數 | 本產品 | MSP430F2471TPM | MSP430F247TPM | MSP430F249TPM | MSP430F2411TPM | MSP430F2412TPM |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 64-LQFP (10x10) | 64-LQFP (10x10) | 64-LQFP (10x10) | 64-LQFP (10x10) | 64-LQFP (10x10) | 64-LQFP (10x10) |
| CPU Architecture | 16-bit MSP430 RISC | 16-bit MSP430 RISC | 16-bit MSP430 RISC | 16-bit MSP430 RISC | 16-bit MSP430 RISC | 16-bit MSP430 RISC |
主要差異化特點
- Defined 56 KB Flash and 4 KB SRAM configuration (對比MSP430F2471TPM)
- Two USCI modules with three supported serial formats (對比MSP430F247TPM)
- 16 MHz processing with a 12-bit ADC and comparator (對比MSP430F249TPM)
設計說明
Place the required supply bypass capacitors close to the device power pins and keep the return path short. Begin with the capacitor values and layout constraints in the manufacturer datasheet, then validate the design with measured rail droop during ADC sampling, timer activity, and USCI transmission. If the board combines the MSP430F2410TPM with a switching supply, keep the regulator's high-current return area away from the ADC and comparator ground references.
Treat analog inputs as high-impedance nodes: minimize copper area around them, avoid routing them beneath digital clocks or serial signals, and provide a nearby ground reference. If the ADC input must cross a split ground region, plan the analog and digital return currents so switching current does not share the sensitive measurement path. Use the manufacturer pin table to verify the selected analog channel and its associated VREF options.
Do not treat package compatibility as proof of firmware compatibility. MSP430F2xx family members can differ in ADC12 implementation, memory capacity, USCI count, and alternate-pin assignments. Before replacing MSP430F2410TPM with MSP430F2471TPM, MSP430F247TPM, MSP430F249TPM, MSP430F2411TPM, or MSP430F2412TPM, compare the device register definitions, vector table, startup code, peripheral instances, and errata.
Estimate junction temperature from actual 3 V supply current, operating frequency, duty cycle, and board thermal resistance rather than using a nominal CPU frequency alone. The 64-LQFP package provides a compact thermal path, but copper area and airflow still influence performance. Measure the controller during maximum USCI activity, simultaneous timer interrupts, and continuous analog conversion to identify thermal or supply-current margins.
合規資訊
The MSP430F2410 is a general-purpose microcontroller rather than an automotive-qualified device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the current manufacturer product documentation.