NE5532ADRE4 - Dual 10MHz Low-Noise Op Amp for Audio | TI
MPN： NE5532ADRE4 ✓ 啟用中NE5532ADRE4 概覽
A low-noise operational amplifier is an analog integrated circuit that amplifies voltage differences while contributing minimal intrinsic noise. The NE5532 belongs to the operational-amplifier hierarchy used for audio preamplification, mixing, buffering, filtering, and instrumentation. Its 5 nV/√Hz typical input-noise characteristic is especially relevant when the amplified signal is sourced from a high-impedance sensor or a low-level microphone.
The device provides 10 MHz typical unity-gain bandwidth, 9 V/µs typical slew rate, 100 dB typical common-mode rejection, and 100 V/mV typical DC voltage gain. These characteristics support audio-band operation with ample bandwidth for feedback networks and active filters. The dual configuration reduces component count in stereo circuitry, while the 8-SOIC package is compatible with automated surface-mount assembly.
The NE5532 uses a conventional voltage-feedback operational-amplifier architecture with two independent amplifiers. Each channel provides inverting and non-inverting inputs, an output, and a power-supply connection. Noise and common-mode rejection are important because they influence the signal-to-noise ratio and the degree to which unwanted supply or common-mode signals appear at the output. Operating from a dual supply also supports bipolar audio signals without biasing the source at mid-rail.
Typical applications include stereo audio preamplifiers, microphone amplifiers, line-level mixers, tone-control circuits, active crossover networks, and low-level audio buffers. In each case, the low-noise input stage helps preserve small signals, while the 10 MHz bandwidth and 9 V/µs slew rate provide margin for gain and phase shaping. Designers must still verify stability with the selected feedback network and load.
The principal design consideration is power-supply bypassing. Place the required input and output decoupling capacitors close to the device pins, keep output routing short, and avoid placing long traces beside noisy switching nodes. Decoupling values and stability guidance should be taken directly from the manufacturer datasheet and typical application circuit rather than inferred from the distributor summaries.
This page combines verified manufacturer information, distributor pricing, pin-compatible substitute references, and practical application guidance. The alternatives are explicitly limited to same-package drop-in candidates, while unavailable electrical details remain marked for validation against each candidate manufacturer’s current datasheet.
直接替換替代品，適用於 NE5532ADRE4 — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： NE5532ADRE4 （相同外形與佔位） — 差異在於 Amplifier Type, Slew Rate, Package, Number of Channels, Operating Temperature.
NE5532DR
✅ 直接替換聯絡詢價
查看資料表 →OPA2134UA/2K5
✅ 直接替換聯絡詢價
查看資料表 →OPA2604UA
✅ 直接替換📋 參考替代品（不在目錄中）
AD823ARZ
✅ 直接替換聯絡詢價
查看資料表 →AD826ARZ
✅ 直接替換📋 參考替代品（不在目錄中）
NJM5532M
✅ 直接替換📋 參考替代品（不在目錄中）
NE5532ADRE4 最大額定值與電氣特性
| Amplifier Type | General Purpose |
| Number of Channels | 2 circuits |
| Unity-Gain Bandwidth | 10 MHz typical |
| Slew Rate | 9 V/µs typical |
| Equivalent Input Noise Voltage | 5 nV/√Hz typical at 1 kHz |
| Common-Mode Rejection Ratio | 100 dB typical |
| DC Voltage Gain | 100 V/mV typical |
| 工作電源電壓 | ±5 V to ±15 V |
| NE5532x Operating Temperature | 0°C to 70°C |
| 封裝 | 8-SOIC, 0.154 inch (3.90 mm) body width |
| Packaging | Tape and reel |
| Product Description | Dual low-noise operational amplifier |
| Manufacturer Product Family | NE5532x and SA5532x |
| 安裝類型 | Surface mount |
NE5532ADRE4 8-soic, 0.154 inch (3.90 mm) body width 腳位配置指南
NE5532ADRE4（8-soic, 0.154 inch (3.90 mm) body width 封裝）的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料： NE5532ADRE4.
請參閱 資料表 以查看完整腳位配置。
典型應用
NE5532ADRE4 適用於 6 應用s: Stereo Audio Preamplifier, Microphone Low-Noise Preamp, Audio Mixing Console, Active Tone-Control Network, Active Crossover and Filter, Line-Level Audio Buffer.
Stereo Audio Preamplifier
The NE5532ADRE4 fits a stereo audio preamplifier because its verified 5 nV/√Hz typical equivalent input noise at 1 kHz helps preserve low-level program material, while two amplifiers are integrated in one 8-SOIC package. The 10 MHz typical unity-gain bandwidth and 9 V/µs typical slew rate provide ample margin for typical audio gain and phase-shaping networks. Each channel can use inverting or non-inverting feedback arrangements, subject to the minimum stable gain specified by the manufacturer. The principal trade-off is that the NE5532x grade is specified from 0°C to 70°C, so extended-temperature industrial equipment should verify the appropriate grade or alternative.
推薦
Microphone Low-Noise Preamp
The NE5532ADRE4 is appropriate for a low-impedance or moderate-impedance microphone preamplifier when low input noise is important. Its 5 nV/√Hz typical equivalent input noise at 1 kHz provides a concrete basis for low-noise gain stages, while the 100 V/mV typical DC gain supports practical inverting stages with moderate feedback resistors. A 10 MHz unity-gain bandwidth can support audio-band filtering, although the chosen feedback network must preserve stability and the required signal bandwidth. Designers should minimize source resistance, maintain a clean return path, and confirm capacitor and bias-current requirements from the complete datasheet before production.
推薦
Audio Mixing Console
A NE5532ADRE4 can serve as a summing or mixing amplifier in an audio console because its dual-channel architecture reduces the component count for stereo or paired signal paths. The verified 9 V/µs slew rate and 10 MHz typical unity-gain bandwidth give designers margin for active gain stages, while the 100 dB typical common-mode rejection helps reduce unwanted common-mode pickup in balanced audio circuitry. Noise performance remains suitable for line-level processing at 5 nV/√Hz typical input noise. Feedback ratios, source impedances, and load impedances must be evaluated together to avoid compromising stability or headroom.
推薦
Active Tone-Control Network
The NE5532ADRE4 can implement active bass, treble, or midrange stages because its verified 10 MHz unity-gain bandwidth supports phase-shaping networks beyond the audible range, and its 9 V/µs slew rate reduces slew-related distortion on larger signals. Two channels allow linked stereo controls, while the low-noise input characteristic helps preserve program level through cascaded gain and summing stages. Component tolerances and the effective resistance seen by each amplifier should be calculated for the target frequency response. The ±5 V to ±15 V operating range also supports conventional bipolar audio rails, subject to output-swing and load requirements in the full datasheet.
推薦
Active Crossover and Filter
The NE5532ADRE4 is suitable for active crossover and audio-filter stages requiring more bandwidth than a basic general-purpose amplifier. Its 10 MHz typical unity-gain bandwidth allows the op amp to operate above audio frequencies while maintaining a 9 V/µs typical slew rate for signal transients. The 5 nV/√Hz typical input noise at 1 kHz is useful in low-level crossover channels where added noise would otherwise be exposed by subsequent gain. Each amplifier channel must remain within its stable feedback topology, and resistor and capacitor tolerances should be selected to control cutoff frequency and phase alignment between channels.
推薦
Line-Level Audio Buffer
The NE5532ADRE4 can buffer a line-level audio source before a longer cable, mixer input, or additional gain stage. Although the task is simpler than low-level preamplification, the verified 5 nV/√Hz typical input noise prevents the buffer from unnecessarily raising the system noise floor. The dual 8-SOIC package allows one part to buffer two channels, and its 10 MHz typical bandwidth provides more than enough bandwidth for conventional audio signals. Designers should check output-current capability, capacitive-load stability, and the required output swing against the load because those limits are not included in the supplied distributor summaries.
推薦
工程參考資料，適用於 NE5532ADRE4 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | NE5532DR | OPA2134UA | OPA2604UA | AD823ARZ | AD826ARZ |
|---|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same |
| Brand | Texas Instruments | Texas Instruments | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
主要差異化特點
- Verified low-noise input performance (對比AD823ARZ)
- Audio-oriented bandwidth and slew-rate margin (對比OPA2134UA)
- Dual amplifier integration in the standard 8-SOIC footprint (對比AD826ARZ)
設計說明
Place the manufacturer-recommended supply-bypass capacitors immediately adjacent to the power pins and use the shortest practical ground return. Keep both amplifier channels on the same side of the PCB where possible, minimize trace resistance in feedback networks, and avoid routing audio outputs near digital clocks, switching regulators, or inductors. Exact capacitance and layout dimensions should follow the current TI datasheet and its recommended land pattern.
Do not assume that any amplifier with eight pins is interchangeable: the NE5532ADRE4 is the 8-SOIC version of the NE5532x family, while NE5532x and SA5532x differ in specified temperature range. Also check the minimum stable gain, output-swing limits, load restrictions, and supply polarity against the original design. A substitute with the same outline is only a true drop-in candidate after its pin functions and electrical limits have been compared.
Keep feedback-loop geometry compact because the verified 10 MHz unity-gain bandwidth can make layout-induced phase shift significant. Use a stable feedback topology, avoid excessive capacitive loading on the output, and place channel-matching resistors and capacitors close to their associated amplifier pins. For low-level audio, use a quiet ground reference and avoid sharing high-current return paths with the input signal.
合規資訊
The supplied excerpts do not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals compliance. The NE5532x is an audio general-purpose amplifier, so AEC-Q100 qualification is not asserted.
