OPA858QIDSGRQ1 - 5.5GHz FET-Input TIA Op-Amp Q1 | TI
MPN： OPA858QIDSGRQ1 ✓ 啟用中OPA858QIDSGRQ1 概覽
A decompensated amplifier is an operational amplifier internally compensated for stable operation only above a minimum closed-loop gain (here 7 V/V). By removing the compensation for unity-gain stability, the decompensated topology achieves dramatically higher bandwidth and lower input-referred noise than unity-gain-stable amplifiers of comparable process technology. In the signal-chain hierarchy, the OPA858-Q1 sits as a wideband voltage-feedback amplifier serving transimpedance amplifier (TIA) and high-gain voltage amplifier roles in high-speed analog front ends.
Key features include the 5.5-GHz GBWP that enables high closed-loop bandwidths at transimpedance gains in the range of tens to hundreds of kilo-ohms, FET inputs that minimize input bias current effects on photodiode and high-impedance nodes, and single-ended single-channel configuration optimized for high-speed signal paths. The Q1 variant is manufactured on TI automotive flows and is qualified per AEC-Q100, supporting automotive lidar, imaging, and test applications that demand supply-chain traceability and automotive-grade reliability.
The architecture combines CMOS input devices with wideband voltage-feedback internals, yielding low input capacitance that is critical in TIA designs because photodiode plus amplifier input capacitance directly limits achievable bandwidth per unit of transimpedance gain. TI provides the OPA858 together with a companion evaluation module and application collateral covering feedback resistor selection, compensation capacitor sizing, and stability analysis.
Typical applications include automotive lidar receiver TIAs, wideband photodiode amplification in optical sensing, high-speed voltage amplification stages, and wideband test and measurement front ends. The device suits any signal chain that requires gain of 7 V/V or higher with multi-hundred-megahertz to gigahertz-class bandwidth.
Design consideration: because the amplifier is only stable at gain >= 7 V/V, noise-gain analysis must be performed at all frequencies, including input capacitance effects at the inverting node; verify phase margin with the TI datasheet stability curves before finalizing feedback-network values.
直接替換替代品，適用於 OPA858QIDSGRQ1 — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： OPA858QIDSGRQ1 （相同外形與佔位） — 差異在於 Amplifier Type, Input Type, Package.
OPA858QDSGRQ1
✅ 直接替換📋 參考替代品（不在目錄中）
OPA858DSGR
✅ 直接替換📋 參考替代品（不在目錄中）
OPA859QDSGRQ1
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品（不在目錄中）
OPA859DSGR
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品（不在目錄中）
OPA858QIDSGRQ1 最大額定值與電氣特性
| Gain Bandwidth Product | 5.5 GHz |
| Minimum Stable Gain | 7 V/V |
| Input Type | FET (CMOS) |
| Amplifier Type | Voltage Feedback, Decompensated |
| Number of Channels | 1 |
| Configuration | Single-Ended |
| Typical Application | Transimpedance Amplifier (TIA), Wideband Voltage Amplifier |
| Transimpedance Gain Range | Tens to hundreds of kilo-ohms |
| Qualification | AEC-Q100 (Automotive Q1) |
| 封裝 | 8-WSON (2x2 mm) |
| 安裝類型 | Surface Mount |
OPA858QIDSGRQ1 8-wson (2x2 mm) 腳位配置指南
OPA858QIDSGRQ1（8-wson (2x2 mm) 封裝）的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料： OPA858QIDSGRQ1.
請參閱 資料表 以查看完整腳位配置。
典型應用
OPA858QIDSGRQ1 適用於 6 應用s: Automotive Lidar Receiver TIA, Wideband Photodiode Amplification, High-Speed Voltage Amplification, Test and Measurement Front Ends, Optical Communication Receivers, Ultrasonic and Sensor Signal Chains.
Automotive Lidar Receiver TIA
The OPA858QIDSGRQ1 fits automotive lidar photodiode receivers because its 5.5-GHz GBWP and FET inputs support high closed-loop bandwidth at transimpedance gains of tens to hundreds of kilo-ohms, directly determining range resolution. As a TIA, the photodiode feeds the inverting node with a large feedback resistor; the decompensated topology at gain >= 7 V/V maximizes bandwidth per transimpedance. AEC-Q100 qualification makes it deployable in production vehicles.
推薦
Wideband Photodiode Amplification
For optical sensing and instrumentation, the OPA858QIDSGRQ1 amplifies photodiode currents across hundreds of megahertz. Its FET inputs draw negligible bias current, preserving accuracy at high-impedance nodes, while low input capacitance preserves bandwidth. Placed immediately after the photodiode in a TIA configuration with optimized feedback resistance and compensation capacitance, it converts weak optical signals into usable voltage with high fidelity and minimal added noise.
推薦
High-Speed Voltage Amplification
As a voltage amplifier at closed-loop gains of 7 V/V and above, the OPA858QIDSGRQ1 delivers gigahertz-class bandwidth for high-speed signal chains such as oscilloscope front ends and wideband gain blocks. The decompensated design trades unity-gain stability for maximum bandwidth-noise performance. Designers must verify noise gain across frequency, including capacitive effects at the inverting input, to guarantee phase margin per the TI stability analysis in the datasheet.
推薦
Test and Measurement Front Ends
In bench and modular instrumentation, the OPA858QIDSGRQ1 provides the wideband, low-noise first stage that sets system noise floor and bandwidth. Its 5.5-GHz GBWP supports multi-hundred-MHz signal paths at gains of tens of V/V, and the compact 2x2 mm WSON package suits dense module layouts. Careful ground-plane design and short input traces are essential to realize datasheet-grade performance in measurement equipment.
推薦
Optical Communication Receivers
Short-reach optical links benefit from the OPA858QIDSGRQ1 as a post-photodiode TIA stage where bandwidth in the hundreds of megahertz to gigahertz range is required. FET inputs minimize shot-noise-degrading bias currents, and the high GBWP allows tens of kilo-ohms transimpedance with usable bandwidth. The supply should be filtered with low-noise LDOs because PSRR degrades at high frequency, making post-regulation ripple rejection important.
推薦
Ultrasonic and Sensor Signal Chains
High-frequency ultrasonic and impedance-sensing front ends use the OPA858QIDSGRQ1 for wideband gain stages following transducers. The gain-of-7 stability threshold matches typical receive-chain gains, and FET input impedance avoids loading resonant transducers. The automotive Q1 grade extends suitability into in-vehicle sensing modules such as ultrasonic park-assist receivers where AEC-Q100 components are mandated by platform requirements.
推薦
推薦產品摘要
工程參考資料，適用於 OPA858QIDSGRQ1 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | OPA858QDSGRQ1 | OPA858DSGR | OPA859QDSGRQ1 |
|---|---|---|---|---|
| Package | 8-WSON (2x2 mm) | 8-WSON (2x2 mm) - same | 8-WSON (2x2 mm) - same | 8-WSON (2x2 mm) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Gain Bandwidth Product | 5.5 GHz | 5.5 GHz | 5.5 GHz | ~1.8 GHz |
| Minimum Stable Gain | 7 V/V | 7 V/V | 7 V/V | Lower (easier to stabilize) |
| Input Type | FET (CMOS) | FET (CMOS) | FET (CMOS) | FET input |
| AEC-Q100 (Automotive Q1) | Yes | Yes | No (commercial grade) | Yes |
| Number of Channels | 1 | 1 | 1 | 1 |
| Primary Application | Wideband TIA / voltage amplifier | Wideband TIA / voltage amplifier | Wideband TIA / voltage amplifier (commercial) | Moderate-bandwidth TIA / amplifier |
主要差異化特點
- Highest GBWP in TI FET-input amplifier family (對比OPA859QDSGRQ1)
- Automotive AEC-Q100 qualification with extended temperature grade (對比OPA858DSGR)
- FET (CMOS) inputs for high-impedance nodes (對比OPA859QDSGRQ1)
設計說明
As a decompensated amplifier stable only at gain >= 7 V/V, the OPA858QIDSGRQ1 requires full-frequency noise-gain analysis. Photodiode capacitance and stray inverting-node capacitance raise noise gain at high frequency and can erode phase margin. Place the feedback network directly at the pins, minimize inverting-node trace area, and verify stability with the TI datasheet phase-margin curves before finalizing Rf and Cf values.
The 8-WSON (2x2 mm) package has an exposed die-pad/thermal structure that must be soldered to a grounded copper pour. Use multiple thermal vias to the ground plane for heat dissipation and low-inductance grounding. Keep input and output traces short and impedance-controlled for gigahertz-class signals, and place 100 nF plus bulk supply decoupling capacitors within 2 mm of the supply pins.
Amplifier PSRR falls at high frequency, so switching-regulator ripple passes directly into the signal path. Power the OPA858QIDSGRQ1 from a low-noise LDO (e.g., TPS7A8300 or TPS7A4701) followed by ferrite-bead and ceramic-capacitor filtering. Simulate or measure the supply rail noise floor; microvolts of ripple at the amplifier supply can appear at the TIA output and limit sensitivity in lidar receivers.
合規資訊
Q1 suffix denotes TI automotive product line with AEC-Q100 qualification. Other compliance statuses not stated in provided data - verify on TI product page.
