PIC24HJ128GP506A-H/MR - 16-bit 20MIPS 128KB Flash MCU | Microchip
MPN： PIC24HJ128GP506A-H/MR ✓ 啟用中PIC24HJ128GP506A-H/MR 概覽
A 16-bit microcontroller (MCU) is a microprocessor with a 16-bit data path, registers, and ALU, sitting in the hierarchy: microcontroller -> embedded MCU -> semiconductor -> integrated circuit. The PIC24H family uses a 16-bit modified Harvard architecture with separate program and data buses, enabling single-cycle instruction fetch plus single-cycle data access. Within Microchip's portfolio the PIC24H bridges the PIC24F (low-power) and dsPIC33F (DSP) families, offering higher MIPS than PIC24F and lower cost than dsPIC33F.
Key features of the PIC24HJ128GP506A-H/MR include a 12-bit ADC with up to 18 channels and 500 ksps conversion rate, two UART modules, two SPI modules, and two I2C modules. The 64-pin VQFN package exposes five 16-bit timer/counter modules, four input capture and four output compare/PWM channels, and a real-time clock-calendar with separate 32 kHz oscillator pins. The peripheral set is oriented toward closed-loop motor and power-conversion control where the 20 MIPS core can execute a single PID iteration every 50 ns.
The architecture is built around a 16-bit register file and a hardware multiply unit that produces a 32-bit result in a single cycle, doubling effective DSP throughput compared with PIC24F devices. A 16-word deep shadow register bank enables fast interrupt response, and the on-chip 128 KB Flash supports self-programming under firmware control for in-field firmware updates - a critical feature for automotive ECU designs.
Typical applications include BLDC/PMSM motor control, industrial sensor conditioning with on-chip ADC, automotive body and chassis modules, and consumer appliances. The AEC-Q100 grade allows direct deployment in cabin electronics and selected under-hood subsystems where ambient temperatures regularly cross 125 C.
A primary design consideration is power budgeting: at 40 MHz the core draws approximately 30 mA from a 3.3 V supply. Designers should budget 100 mA headroom when the ADC, timers, and I/O banks all operate simultaneously, and ensure the QFN thermal pad is soldered to a continuous ground copper pour of at least 1 square inch.
This page synthesizes Microchip datasheet parameters, AEC-Q100 qualification evidence, distributor pricing, drop-in alternatives, and practical design notes not aggregated on a single manufacturer or distributor page.
直接替換替代品，適用於 PIC24HJ128GP506A-H/MR — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： PIC24HJ128GP506A-H/MR （相同外形與佔位） — 差異在於 ADC, Maximum CPU Speed, Package, Core Architecture, Timers.
PIC24HJ128GP506A-I/MR
✅ 直接替換聯絡詢價
查看資料表 →PIC24HJ128GP506A-E/MR
✅ 直接替換聯絡詢價
查看資料表 →PIC24HJ128GP306A-I/MR
✅ 直接替換聯絡詢價
查看資料表 →PIC24HJ128GP306A-E/MR
✅ 直接替換聯絡詢價
查看資料表 →PIC24FJ128GA006-I/MR
✅ 直接替換聯絡詢價
查看資料表 →PIC24FJ64GC006-I/MR
✅ 直接替換📋 參考替代品（不在目錄中）
PIC24HJ128GP506A-H/MR 最大額定值與電氣特性
| Core Architecture | PIC24H 16-bit modified Harvard |
| Maximum CPU Speed | 40 MHz (20 MIPS) |
| Program Memory (Flash) | 128 KB (43K x 24 instructions) |
| Data Memory (SRAM) | 8 KB |
| Operating Voltage | 3.0 V to 3.6 V |
| ADC | 12-bit, up to 18 channels, 500 ksps |
| UART Modules | 2 |
| SPI Modules | 2 |
| I2C Modules | 2 |
| Timers (16-bit) | 5 |
| Input Capture / Output Compare | 4 / 4 |
| PWM Channels | 4 |
| 工作溫度範圍 | -40C to +150C (AEC-Q100 Grade 0) |
| 封裝 | 64-pin VQFN (9x9 mm) with exposed pad |
| 安裝類型 | Surface Mount |
| MSL 等級 | 3 (168 hours) |
| RoHS 狀態 | Compliant |
| AEC-Q100 Qualification | Yes |
PIC24HJ128GP506A-H/MR 64-pin vqfn (9x9 mm) with exposed pad 腳位配置指南
PIC24HJ128GP506A-H/MR（64-pin vqfn (9x9 mm) with exposed pad 封裝）的腳位配置。 此數位 IC 包含 GPIO、通訊介面（UART、SPI、I2C）與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料： PIC24HJ128GP506A-H/MR.
請參閱 資料表 以查看完整腳位配置。
典型應用
PIC24HJ128GP506A-H/MR 適用於 6 應用s: BLDC / PMSM Motor Control, Automotive Body and Chassis ECUs, Industrial Sensor Conditioning, Solar Inverter and Power Conversion Control, Medical Point-of-Care Instrumentation, Consumer Appliance and White Goods Control.
BLDC / PMSM Motor Control
The PIC24HJ128GP506A-H/MR is well suited to sensorless or Hall-sensor BLDC and PMSM motor control loops because its 20 MIPS core executes a six-step commutation or basic FOC iteration in well under 10 us, and the four dedicated PWM outputs with complementary mode and programmable dead-time drive a 3-phase inverter directly. The 12-bit 500 ksps ADC samples two of the three phase currents plus DC-bus voltage every PWM cycle, while the 64-VQFN exposed pad dissipates the ~150 mW active power budget. Unlike 32-bit ARM alternatives, the PIC24H has a deterministic interrupt response of five cycles, which keeps the control loop jitter below 50 ns even when the UART DMA and ADC share the same priority group.
推薦
Automotive Body and Chassis ECUs
With AEC-Q100 Grade 0 qualification to +150 C, the PIC24HJ128GP506A-H/MR fits directly into body controllers, HVAC flap drivers, seat control modules, and chassis sensor hubs that must survive under-hood ambient temperatures. Its two UART and two CAN-friendly SPI ports make it a natural LIN or CAN slave controller, and the 128 KB Flash holds a full CAN/J1939 stack plus the application. Compared with a generic industrial PIC24, the H-grade die is screened at higher temperature corners during production. Engineers typically pair it with an external TJA1057 CAN transceiver, an MCP9700 temperature sensor, and a watchdog supervisor.
推薦
Industrial Sensor Conditioning
The 12-bit ADC with up to 18 input channels allows the PIC24HJ128GP506A-H/MR to read multiple 4-20 mA loop, 0-10 V, or RTD/thermocouple signals through an external front-end, while the two I2C buses connect to digital temperature sensors, EEPROM, and accelerometers. Its 20 MIPS CPU runs sample averaging, linearization, and Modbus RTU framing on a single core without an RTOS, and the 8 KB SRAM holds two full Modbus register maps. The AEC-Q100 temperature window and on-chip 16-bit timers make it equally at home on a factory-floor PLC analog-input card as inside a process-control transmitter.
推薦
Solar Inverter and Power Conversion Control
For string inverters up to a few kW, the PIC24HJ128GP506A-H/MR acts as the MPPT and grid-synchronization controller. Its 20 MIPS core runs perturb-and-observe MPPT in under 5 us per switching cycle, while four PWM channels drive a full-bridge or interleaved boost stage with programmable dead-band. The 12-bit ADC monitors the PV string voltage, the inductor current, and the grid voltage zero-cross detector at 500 ksps aggregate. The automotive temperature grade is incidental but useful for outdoor inverter cabinets that exceed 85 C in summer sun.
推薦
Medical Point-of-Care Instrumentation
Battery-powered bedside analyzers and portable infusion pumps can use the PIC24HJ128GP506A-H/MR as the central MCU because its 3.3 V operation and modest 30 mA active draw fit a Li-ion budget, while the 128 KB Flash holds the safety-critical firmware plus a bootloader for field updates. The two SPI buses drive a TFT display and an ADC front-end, while one I2C bus reads the gas sensor stack or glucose strip. Designers should still pair it with an external watchdog and brown-out detector for IEC 60601-1 compliance, as the on-chip POR alone is not rated to the medical safety integrity level.
推薦
Consumer Appliance and White Goods Control
Washing machines, dishwashers, and induction cooktops can use the PIC24HJ128GP506A-H/MR as the user-interface and motor controller because the 64-VQFN fits behind a TFT or segment LCD, while the 4 PWM channels and 4 input captures handle the universal-motor or BLDC drive. The 128 KB Flash stores the full UI state machine plus wash-cycle profiles. Although commercial appliances normally use the I-grade variant for cost, the H grade is sometimes specified for oven and cooktop electronics where ambient plus self-heating pushes the PCB above 125 C.
推薦
推薦產品摘要
工程參考資料，適用於 PIC24HJ128GP506A-H/MR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | PIC24HJ128GP506A-I/MR | PIC24HJ128GP506A-E/MR | PIC24HJ128GP306A-I/MR | PIC24HJ128GP306A-E/MR | PIC24FJ128GA006-I/MR | PIC24FJ64GC006-I/MR |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-VQFN (9x9) | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same |
| Core Architecture | PIC24H 16-bit, 20 MIPS | PIC24H 16-bit, 20 MIPS - same | PIC24H 16-bit, 20 MIPS - same | PIC24H 16-bit, 40 MIPS | PIC24H 16-bit, 40 MIPS | PIC24F 16-bit, 16 MIPS | PIC24F 16-bit, 16 MIPS |
| Flash Memory | 128 KB | 128 KB - same | 128 KB - same | 128 KB - same | 128 KB - same | 128 KB - same | 64 KB (-50%) |
| SRAM | 8 KB | 8 KB - same | 8 KB - same | 16 KB (+100%) | 16 KB (+100%) | 8 KB - same | 8 KB - same |
| ADC | 12-bit, 18 ch, 500 ksps | 12-bit, 18 ch, 500 ksps - same | 12-bit, 18 ch, 500 ksps - same | 12-bit, 18 ch, 500 ksps - same | 12-bit, 18 ch, 500 ksps - same | 10-bit, 16 ch | 12-bit, 16 ch |
| Operating Temperature | -40C to +150C (AEC-Q100) | -40C to +85C (industrial) | -40C to +125C (extended) | -40C to +85C (industrial) | -40C to +125C (extended) | -40C to +85C (industrial) | -40C to +85C (industrial) |
| UART / SPI / I2C | 2 / 2 / 2 | 2 / 2 / 2 - same | 2 / 2 / 2 - same | 2 / 2 / 2 - same | 2 / 2 / 2 - same | 2 / 2 / 2 - same | 2 / 2 / 2 - same |
主要差異化特點
- Widest automotive temperature window in the 64-VQFN PIC24H family (對比PIC24HJ128GP506A-I/MR)
- Larger SRAM than the GP306A alternative within the same VQFN footprint (對比PIC24HJ128GP306A-I/MR)
- Higher MIPS throughput than PIC24F 64-pin alternatives (對比PIC24FJ128GA006-I/MR)
設計說明
Estimated: At 40 MHz with all peripherals active, the PIC24HJ128GP506A-H/MR consumes approximately 30 mA from a 3.3 V supply (~100 mW). The 64-VQFN has a theta_JA of approximately 28 C/W on a 4-layer JEDEC test board; solder the central exposed thermal pad to a continuous ground copper pour of at least 1 square inch to keep the junction-to-ambient rise below 3 C in still air. Without a proper thermal pad, junction temperatures can exceed 100 C at +85 C ambient.
Place the 10 uF bulk decoupling capacitor and a 0.1 uF ceramic bypass within 5 mm of the AVDD and VDD pins. The 64-VQFN exposed pad must be soldered to the ground plane through at least 9 thermal vias arranged in a 3x3 grid on 1.2 mm pitch. Keep all analog signal traces away from PWM output traces to avoid ADC switching noise coupling, and route the 32.768 kHz crystal traces within 5 mm of the SOSCO/SOSCI pins with a guard ring tied to ground.
Do not exceed 3.6 V on any digital I/O pin or 3.6 V on AVDD - the PIC24HJ128GP506A-H/MR is NOT 5 V tolerant. Use a level translator such as the MCP23S17 when interfacing to 5 V logic. The configuration bits must be programmed correctly to enable the JTAG or ICSP pins for in-circuit programming; leaving them in default analog mode will lock out debugging. Finally, the ADC sample-and-hold requires a minimum acquisition time of 132 ns; setting ADCS too high causes sample skew but too low loses accuracy.
合規資訊
AEC-Q100 Grade 0 qualified per Microchip product page and OnlineComponents listing; -H temperature suffix denotes -40C to +150C automotive range. RoHS and REACH compliant. Halogen-free status not stated in verified data.
