TPS92513HVDGQR - 65V 1.5A Buck LED Driver HVSSOP-10 | TI
MPN： TPS92513HVDGQR ✓ 啟用中TPS92513HVDGQR 概覽
A buck LED driver is a switch-mode DC-DC converter that regulates the current through an LED string rather than the voltage across it, which provides uniform brightness regardless of forward-voltage variation between LEDs. Within the broader power-management IC (PMIC) hierarchy, the TPS92513HV sits in the LED-driver category, which is itself a subset of switching regulators alongside buck, boost, and buck-boost converters optimized for light-load efficiency.
Key features include cycle-by-cycle overcurrent protection, thermal shutdown, an enable/shutdown pin, an analog adjust (ADJ) input for current programming, and a PWM dim input. The peak-current-mode control topology yields good line and load regulation and supports user-selectable switching frequencies via an external resistor. The HVSSOP-10 PowerPAD package exposes the die ground pad for low thermal resistance (about 45 C/W on a standard 2 oz. 4-layer board), which keeps junction temperatures in check at full 1.5 A output. Designers can also synchronize the device to an external clock for EMI-sensitive applications.
Typical applications include architectural and commercial LED lighting, automotive interior and exterior LED drivers, industrial signage, emergency lighting, and 24 V track-lighting fixtures. The 65-V rating gives substantial transient headroom on 24 V industrial buses where load-dump-style surges are common. The wide VIN range also supports daisy-chained LED luminaires powered from a single high-voltage rail.
When laying out the PCB, place the input ceramic bypass, the bootstrap capacitor, and the freewheeling Schottky diode as close to the IC as possible to minimize parasitic loop inductance. The exposed pad must be soldered to a copper pour spanning multiple thermal vias to keep junction temperatures within the 150 C thermal-shutdown limit during continuous 1.5 A operation.
直接替換替代品，適用於 TPS92513HVDGQR — 相同封裝，腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號： TPS92513HVDGQR （相同外形與佔位） — 差異在於 Control Method, Input Voltage Range, Operating Temperature Range, Package, Switching Frequency Range.
TPS92513HVDGQT
✅ 直接替換📋 參考替代品（不在目錄中）
TPS92513HVQDGQRQ1
✅ 直接替換📋 參考替代品（不在目錄中）
TPS92513HVDGQRG4
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品（不在目錄中）
TPS92510DGQR
✅ 直接替換聯絡詢價
查看資料表 →TPS92513HVDGQR 最大額定值與電氣特性
| 拓撲 | Step-Down (Buck) Current Regulator |
| 輸入電壓範圍 | 4.5 V to 65 V |
| 最大輸出電流 | 1.5 A |
| 輸出數量 | 1 |
| Switching Frequency Range | 100 kHz to 2 MHz (external resistor set) |
| Control Method | Peak current mode |
| Dimming | Analog and PWM |
| Output Voltage Reference | 200 mV (typical, across internal/adjust sense reference) |
| 工作溫度範圍 | -40 C to +125 C |
| 封裝 | 10-pin HVSSOP (DGQ) with PowerPAD |
| 安裝類型 | Surface Mount |
| RoHS 狀態 | Compliant |
| AEC-Q100 Qualification | Not qualified (TPS92513HV-Q1 variant is AEC-Q100) |
| 過熱關機 | Yes (internal) |
TPS92513HVDGQR 腳位配置
| 腳位 1 | VIN — Input supply voltage (4.5 V to 65 V) |
| 腳位 2 | EN — Enable / shutdown input (active high) |
| 腳位 3 | ADJ — Analog current adjust input (set via external sense resistor) |
| 腳位 4 | RT — Timing resistor for switching-frequency setting |
| 腳位 5 | COMP — Compensation node for the peak-current-mode loop |
| 腳位 6 | BST — Bootstrap capacitor for high-side gate drive |
| 腳位 7 | SW — Switch node - tied to the freewheeling Schottky and inductor |
| 腳位 8 | PGND — Power ground - return for the integrated MOSFET |
| 腳位 9 | AGND — Analog ground (must be Kelvin-connected to PGND) |
| 腳位 10 | EP — Exposed thermal pad - solder to PCB ground pour for heatsinking |
典型應用
TPS92513HVDGQR 適用於 6 應用s: Industrial 24V/48V LED Lighting, Architectural Track and Downlight Fixtures, Automotive Interior and Exterior Lighting, Emergency and Safety Lighting, Horticultural and Grow-Light Fixtures, Signage and Channel-Letter Illumination.
Industrial 24V/48V LED Lighting
The TPS92513HVDGQR is well suited to industrial lighting rails fed from 24-V or 48-V bus converters because its 4.5-V to 65-V VIN tolerance covers both nominal points plus substantial transient headroom. With 1.5-A output current and integrated 200-mOhm-class MOSFET, the part drives a single high-brightness LED string while the analog ADJ pin simplifies dim-to-warm control loops. Typical efficiency reaches the mid-80 percent range at moderate step-down ratios, and thermal shutdown plus cycle-by-cycle OCP protect against field shorts in high-bay fixtures.
推薦
Architectural Track and Downlight Fixtures
Architectural track lighting is commonly wired in series of LED modules along a single 48-V feeder, where a constant-current buck regulator eliminates brightness mismatch between modules. The TPS92513HVDGQR's 65-V rating absorbs turn-off voltage spikes from the long track inductance and its PWM-dimming input allows 0 to 100 percent brightness without audible flicker from the analog ADJ. The 10-pin HVSSOP PowerPAD footprint fits inside compact MR16- and PAR30-style housings where board area is at a premium.
推薦
Automotive Interior and Exterior Lighting
For daytime running lights, fog lamps, and interior courtesy lighting, the TPS92513HVDGQR automotive sibling TPS92513HVQDGQRQ1 offers AEC-Q100 qualification in the same HVSSOP-10 PowerPAD. The 65-V maximum rating handles 24-V load-dump transients that exceed 40 V and the integrated short-circuit protection prevents damage during harness pin shorts. Designers typically add an EMI input filter to meet CISPR 25 conducted emissions, while the externally set switching frequency lets them place the fundamental away from AM-band receivers.
推薦
Emergency and Safety Lighting
Battery-backed emergency luminaires sit on a charger rail that can rise above 40 V during recharge and during AC-mains brownout recovery. The TPS92513HVDGQR's 65-V headroom avoids avalanche at the input and its thermally protected PowerPAD package survives the elevated ambient temperatures inside ceiling-mounted fixtures. The PWM dimming input also supports end-of-life indicator pulses required by safety codes without adding a second driver IC.
推薦
Horticultural and Grow-Light Fixtures
Horticultural LEDs often run from 36-V or 48-V constant-voltage buses that are pumped to 1.5-A-plus per string to achieve PPFD targets, and the TPS92513HVDGQR's 1.5-A capability combined with 65-V rating is a close fit. The wide VIN tolerance handles the elevated bus voltage seen when the upstream PFC stage's output rises at light load, and the PWM dimming input is directly compatible with 0-to-10-V dimming conversion circuits used in greenhouse controllers.
推薦
Signage and Channel-Letter Illumination
Long-run channel-letter and edge-lit signage typically wires hundreds of LEDs in series from a 48-V supply, where any single LED failure must not open-circuit the whole string. The TPS92513HVDGQR's current-mode regulation maintains uniform brightness despite the long strings and its analog ADJ input accepts a thermistor for ambient or LED-temperature compensation. The integrated MOSFET keeps the BOM to a handful of capacitors, one inductor, and a Schottky diode, which simplifies the small form factors behind acrylic panels.
推薦
推薦產品摘要
工程參考資料，適用於 TPS92513HVDGQR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TPS92513HVDGQT | TPS92513HVQDGQRQ1 | TPS92513HVDGQRG4 | TPS92510DGQR |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 10-pin HVSSOP (DGQ) PowerPAD | 10-pin HVSSOP (DGQ) PowerPAD - same | 10-pin HVSSOP (DGQ) PowerPAD - same | 10-pin HVSSOP (DGQ) PowerPAD - same | 10-pin HVSSOP (DGQ) PowerPAD - same |
| Input Voltage Range | 4.5 V to 65 V | 4.5 V to 65 V | 4.5 V to 65 V | 4.5 V to 65 V | 4.5 V to ~42 V (lower-VIN variant) |
| Maximum Output Current | 1.5 A | 1.5 A | 1.5 A | 1.5 A | 1.5 A |
| Dimming | Analog and PWM | Analog and PWM | Analog and PWM | Analog and PWM | Analog and PWM |
| AEC-Q100 Qualification | Not qualified | Not qualified | Yes (AEC-Q100) | Not qualified | Not qualified |
| Reel Quantity | 2,500 pcs (suffix R) | 250 pcs (suffix T) | 2,500 pcs (suffix R) | 2,500 pcs | 2,500 pcs |
| Operating Temperature Range | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C |
主要差異化特點
- Wide 65-V input range on the same 10-pin HVSSOP footprint (對比TPS92510DGQR)
- AEC-Q100 option in the same footprint for automotive designs (對比TPS92513HVQDGQRQ1)
- Reel-size flexibility without electrical change (對比TPS92513HVDGQT)
設計說明
Place the input ceramic bypass capacitor (recommended 1 uF X7R minimum), the bootstrap capacitor (typical 0.1 uF X7R), and the freewheeling Schottky diode immediately adjacent to the SW, BST, and PGND pins. Keep the SW copper pour small and surrounded by PGND pour to minimize EMI loop area. The exposed thermal pad must be soldered to a continuous ground copper pour stitched with multiple thermal vias (8 to 12 vias in a 4-layer 2-oz board) - skipping this yields a thermal resistance rise that triggers shutdown at full 1.5 A.
Estimated: at full 1.5 A output from 24-V VIN to a 12-V LED string, the IC dissipates roughly (24-12) * 1.5 * (1 - efficiency fraction), where efficiency is approximately 0.85. That gives a die dissipation of approximately 2.8 W. With the package's PowerPAD and a 4-layer 2-oz board, theta_JA is around 45 C/W, yielding a junction temperature rise of about 125 C above a 70 C ambient - close to the 150 C thermal-shutdown trip. If the LED string uses a higher voltage, the dissipation falls and headroom improves. Reduce the design margin by adding a top-layer copper flood under the IC or upgrading to a 4-layer board with continuous inner copper.
Do not exceed 65 V at VIN; even brief transients above the absolute-maximum will damage the internal MOSFET and the bootstrap diode. The ADJ pin senses roughly 200 mV; using a low-precision sense resistor (>1 percent tolerance) degrades LED-current regulation. Also ensure the AGND pin is Kelvin-connected to the PowerPAD/PGND pour with a single trace or via, otherwise internal bias currents can introduce measurement offsets that drift LED brightness across load.
合規資訊
RoHS and REACH compliant per TI product page. The standard grade is not AEC-Q100 qualified; use the TPS92513HVQDGQRQ1 variant for AEC-Q100 applications.
