XC2C32A-4PCG44C - 32-Macrocell 323MHz CPLD | AMD Xilinx
MPN: XC2C32A-4PCG44C ✗ 停產XC2C32A-4PCG44C 概覽
A CPLD is a programmable semiconductor that sits between fixed-function logic and more complex FPGAs. Its architecture groups user logic into macrocells connected by a programmable interconnect. Because the configuration is stored in nonvolatile memory, the XC2C32A retains its logic after power is removed and requires no external configuration PROM. In the system hierarchy, a CPLD is a programmable-logic device, a digital integrated circuit, and a semiconductor component used to implement control, interface, decoding, and glue-logic functions.
Key device characteristics include 32 macrocells, 750 gates, 323 MHz maximum operating frequency, 0.18 µm CMOS fabrication, and operation from a 1.8 V supply. The CoolRunner-II architecture provides nonvolatile configuration and fast propagation performance suited to compact control logic. The DS310 product specification also lists support for multiple LVCMOS and LVTTL input/output standards, including 1.5 V, 1.8 V, 2.5 V, and 3.3 V operating conditions described in that document.
The XC2C32A implementation combines a relatively small logic array with numerous dedicated I/O pins. This balance makes it useful where a designer needs reliable timing closure, short routing paths, and a simple configuration workflow rather than the resource density of an FPGA. Its 44-lead PLCC outline supports compact board layouts, and its -4 speed grade provides a defined performance level for designs operating at or below the device's stated frequency ceiling.
Typical applications include bus decoding and address multiplexing, peripheral interface control, industrial control and automation modules, firmware boot sequencing, display and keypad control, low-power embedded glue logic, and general-purpose prototyping platforms. The device is particularly suitable for designs in which nonvolatile configuration, moderate logic density, and rapid implementation are more valuable than large embedded processor or memory resources.
When designing a PCB for this CPLD, verify every signal against the DS310 pin description table and confirm the voltage level of each I/O bank before connecting external circuitry. Provide a stable core supply with suitable decoupling, route sensitive clock and control nets away from noisy switching nodes, and use the manufacturer's programming and test recommendations. Legacy software and driver support should be validated before a new production design depends on the CoolRunner-II toolchain.
This page combines device specifications, package identification, lifecycle guidance, drop-in replacement analysis, comparison tables, and practical board-level notes. It provides engineers with the information needed to determine whether the XC2C32A-4PCG44C fits an existing 44-pin PLCC footprint and how to evaluate equivalent speed-grade and temperature-grade options before committing a design to a legacy programmable-logic family.
直接替換替代品,適用於 XC2C32A-4PCG44C — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: XC2C32A-4PCG44C (相同外形與佔位) — 差異在於 Configuration Memory, Device Type, Process Technology, Speed Grade.
XC2C32A-4PC44C
✅ 直接替換聯絡詢價
查看資料表 →XC2C32A-4PCG44I
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
XC2C32A-5PCG44C
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
XC2C32A-6PCG44C
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
XC2C32A-5PCG44I
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
XC2C32A-4PCG44C 最大額定值與電氣特性
| Device Type | Complex programmable logic device (CPLD) |
| Device Family | CoolRunner-II |
| Macrocell Count | 32 macrocells |
| Logic Gate Count | 750 gates |
| Maximum Operating Frequency | 323 MHz |
| Speed Grade | -4 |
| Process Technology | 0.18 µm CMOS |
| Core Supply Voltage | 1.8 V |
| Configuration Memory | Nonvolatile |
| Package Type | 44-pin PLCC |
| Package Designation | PCG44 |
| Temperature Grade | Commercial |
| Supported I/O Standards | LVCMOS and LVTTL |
| Documented I/O Voltage Conditions | 1.5 V, 1.8 V, 2.5 V, and 3.3 V |
| Manufacturer | AMD Xilinx |
| Datasheet Document Number | DS310 |
| 安裝類型 | Surface Mount |
XC2C32A-4PCG44C pcg44 腳位配置指南
XC2C32A-4PCG44C(pcg44 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: XC2C32A-4PCG44C.
請參閱 資料表 以查看完整腳位配置。
典型應用
XC2C32A-4PCG44C 適用於 6 應用s: Industrial Control and Automation Logic, Peripheral Interface and Bus Decoding, Boot Sequencing and Power Control, Display, Keypad, and Human-Interface Control, Low-Power Embedded Glue Logic, Legacy Platform and Prototyping Support.
Industrial Control and Automation Logic
The XC2C32A-4PCG44C fits compact industrial control modules that require deterministic logic for relay sequencing, interlocks, alarm handling, and state-machine control. Its 32 macrocells and 750 gates provide enough capacity for typical glue logic, while the stated 323 MHz maximum operating frequency supports clocked control paths with comfortable timing margin. The device retains its configuration in nonvolatile memory, allowing the controller to begin execution immediately after power-up without an external configuration PROM. For panel or rack-mounted systems, the 44-pin PLCC package also simplifies inspection and rework, although the exact DS310 pinout and commercial temperature limits must be checked against the enclosure environment.
推薦
Peripheral Interface and Bus Decoding
The XC2C32A-4PCG44C is appropriate for address decoding, peripheral multiplexing, and host-to-target bus translation in legacy embedded systems. Thirty-two macrocells allow several parallel decode functions or moderate state machines to be consolidated without introducing a larger FPGA. Its stated 323 MHz performance level is useful when the interface must operate from a reasonably fast system clock, while the nonvolatile configuration eliminates repeated configuration-loader overhead after power cycling. Board designers should assign each interface signal directly from the DS310 lead table and confirm that the selected LVCMOS or LVTTL voltage matches the connected device, particularly when interfacing older 5 V logic through appropriate level translation.
推薦
Boot Sequencing and Power Control
The XC2C32A-4PCG44C can implement boot sequencing, reset generation, and power-enable control around processors or programmable controllers. Its nonvolatile configuration makes it practical for holding system rails in a defined order and releasing peripherals after the main supply stabilizes. With 750 gates and 32 macrocells, several sequencing paths, timeout counters, and fault-latch functions can be combined in one device. The stated 323 MHz operating frequency is more than sufficient for typical power-management sequencing, so design effort should focus instead on supply sequencing limits and I/O tolerance. Use the DS310 absolute-maximum ratings to verify every control output against the power rail it influences.
推薦
Display, Keypad, and Human-Interface Control
The XC2C32A-4PCG44C can manage keypad scanning, LED multiplexing, display timing, and front-panel state logic in a compact instrument or control terminal. Thirty-two macrocells are sufficient for debouncing, counter, and multiplexing functions when the display itself is handled by a dedicated controller. The CPLD's fast stated operating frequency supports deterministic scan timing, while nonvolatile configuration retains user-interface behavior after power loss. Because legacy panel interfaces often mix 3.3 V and 5 V signaling, confirm each input threshold and output level in the DS310 electrical tables before connecting the panel cables, and use series damping where long traces are unavoidable.
推薦
Low-Power Embedded Glue Logic
The XC2C32A-4PCG44C is useful for consolidating miscellaneous glue logic around microcontrollers, sensors, and communication transceivers. Its 32 macrocells can implement protocol formatting, interrupt qualification, watchdog handling, and peripheral adaptation without occupying a larger programmable-logic array. The 1.8 V core supply and documented multi-level I/O options provide flexibility when the surrounding circuit operates from several voltage domains, while the 750-gate budget keeps power and routing requirements modest. Confirm I/O-drive strength, slew, and input-level tolerances from DS310 for each external signal, and keep high-current or high-voltage loads away from the CPLD pins by using external drivers.
推薦
Legacy Platform and Prototyping Support
The XC2C32A-4PCG44C remains practical for maintaining or replicating legacy platform logic where an existing board already uses the 44-pin PLCC footprint. Its 32 macrocells and 750 gates are large enough to reproduce compact decoder, latch, and control configurations from established CPLD designs. Because the device belongs to a mature CoolRunner-II family, engineers should confirm that the installed programming tools, device drivers, and third-party intellectual-property libraries still support the exact device. Use the manufacturer ordering and cross-reference tables before assigning an alternative suffix, since speed grade and environmental suffix changes affect procurement qualification even when the board outline remains the same.
推薦
推薦產品摘要
工程參考資料,適用於 XC2C32A-4PCG44C — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | XC2C32A-4PC44C | XC2C32A-4PCG44I | XC2C32A-5PCG44C | XC2C32A-6PCG44C | XC2C32A-5PCG44I |
|---|---|---|---|---|---|---|
| Brand | AMD | AMD | AMD | AMD | AMD | AMD |
| Package | PLCC-44 | PLCC-44 | PLCC-44 | PLCC-44 | PLCC-44 | PLCC-44 |
| Device Family | CoolRunner-II | CoolRunner-II | CoolRunner-II | CoolRunner-II | CoolRunner-II | CoolRunner-II |
| Macrocell Count | 32 macrocells | 32 macrocells | 32 macrocells | 32 macrocells | 32 macrocells | 32 macrocells |
| Logic Gate Count | 750 gates | 750 gates | 750 gates | 750 gates | 750 gates | 750 gates |
| Speed Grade | -4 | -4 | -4 | -5 | -6 | -5 |
| Temperature Grade | Commercial | Commercial | Industrial | Commercial | Commercial | Industrial |
| Core Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Process Technology | 0.18 µm CMOS | 0.18 µm CMOS | 0.18 µm CMOS | 0.18 µm CMOS | 0.18 µm CMOS | 0.18 µm CMOS |
主要差異化特點
- Commercial-grade ordering with a defined -4 speed grade (對比XC2C32A-4PCG44I)
- Direct speed-grade migration within the same 44-pin PLCC family (對比XC2C32A-5PCG44C)
- Higher-speed migration for timing-constrained designs (對比XC2C32A-6PCG44C)
- Closest alternate 44-lead ordering code (對比XC2C32A-4PC44C)
設計說明
Use the DS310 pin-description table and package drawing to create the PLCC footprint, and confirm whether the board requires a through-hole PLCC socket or a leaded surface-mount arrangement. Place the device away from board edges and provide adequate clearance for soldering access and inspection. The programming pins, configuration pins, power rails, and ground connections must follow the manufacturer tables exactly rather than being inferred from a similar 44-lead ordering code.
Decouple the 1.8 V core supply close to the device with the capacitance and placement recommended in DS310. Keep each I/O supply domain within its specified operating range, because LVCMOS and LVTTL signals are not automatically interchangeable across 1.5 V, 1.8 V, 2.5 V, and 3.3 V conditions. Use series damping on board-edge or long external traces, and never allow an I/O pin to exceed the published absolute-maximum voltage.
Do not treat the commercial and industrial suffixes as procurement synonyms. XC2C32A-4PCG44C uses the commercial ordering option, while XC2C32A-4PCG44I identifies the industrial alternative. Faster -5 and -6 parts share the board family but require validation against their own AC timing, power, and temperature data. Confirm the complete ordering code in the AMD cross-reference table before releasing a purchasing or ECO document.
Route clock and reset networks away from high-current switching nodes and keep the ground path continuous beneath the device footprint. For designs that use several I/O voltage standards, place the relevant decoupling at the interface connectors and the core decoupling at the CPLD pins. Because a CPLD offers deterministic interconnect, timing performance still depends on good power delivery and controlled return paths rather than on logic placement alone.
合規資訊
The PCG ordering suffix historically identifies a lead-free-oriented commercial option, but a formal RoHS, REACH, halogen-free, or conflict-minerals declaration is not stated in the manufacturer information used for this listing. AEC-Q100 is not applicable because the product is not an automotive-qualified device.