集成电路

PIC32MX530F128LT-50I/PT

PIC32MX530F128LT-50I/PT - 50MHz 128KB Flash 32-bit MCU | Microchip

The Microchip PIC32MX530F128LT-50I/PT is a 32-bit MIPS M4K microcontroller running up to 50 MHz with 128 KB of Flash and 16 KB of SRAM, housed in a 100-pin TQFP (12x12 mm) package. It is part of the PIC32MX5xx family and integrates USB, I2S audio, CTMU, and a 10-bit ADC with up to 28 analog inputs on this 100-pin variant. A 32-bit microcontroller (MCU) is an integrated circuit combining a high-performance CPU, Flash program memory, SRAM, and a rich set of on-chip peripherals (ADC, timers, communication controllers, I/O). In the system hierarchy, an MCU sits above 8/16-bit microcontrollers and below microprocessors (MPU), occupying the middle ground that balances deterministic real-time control with sufficient throughput for user interfaces, connectivity stacks, and signal processing. The PIC32MX5xx family is a MIPS32 M4K core-based line from Microchip's PIC32 portfolio, used widely in consumer, industrial, and USB-enabled embedded designs. Key features of the PIC32MX530F128LT-50I/PT include: 128 KB Flash, 16 KB SRAM, 50 MHz core clock with 50 MIPS sustained performance, USB 2.0 full-speed OTG controller, I2S/PCM audio interface, CTMU for capacitive touch, a 10-bit 1 Msps ADC, multiple UART/SPI/I2C ports, and an operating voltage range of 2.5V to 3.6V. The 100-pin TQFP package exposes a wide peripheral pinout enabling simultaneous use of USB, Ethernet RMII (via peripheral sharing), parallel PMP bus, and 78 user I/O pins. Architecturally, the device uses a single-cycle MIPS32 M4K core with separate instruction and data buses (Harvard-style prefetch), a 5-stage pipeline, and tightly-coupled peripherals mapped through DMA, which offloads peripheral-to-memory transfers from the CPU. The 50 MHz core delivers 50 DMIPS, sufficient for USB stack handling, graphics UI, and protocol stacks such as TCP/IP or audio processing. Industrial temperature grade (-40C to +85C) is indicated by the -50I suffix. Typical applications include USB peripherals and HID devices, audio playback/recording using I2S, capacitive-touch user interfaces with CTMU, sensor hubs with ADC scanning, industrial HMI panels with PMP display bus, and IoT edge nodes that require USB or I2S connectivity. Designers pick this part when they need USB + I2S + ADC in a single chip with ample I/O for a 100-pin board layout. When designing with this device, ensure the 2.5V-3.6V supply is decoupled close to the VDD pins with 0.1uF + bulk caps. The USB D+/D- lines need 90 ohm differential impedance and ESD protection. The internal 8 MHz RC oscillator can be used for USB start-up, but a 48 MHz PLL clock is required for USB full-speed operation. The CTMU pins can be repurposed as standard digital I/O if touch sensing is not used. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes for the PIC32MX530F128LT-50I/PT in a form not found in the manufacturer datasheet alone.

USD $3.12 有现货

PIC32MX530F128LT-I/PF

PIC32MX530F128LT-I/PF - 32-bit 40MHz 128KB Flash MCU | Microchip

The Microchip Technology PIC32MX530F128LT-I/PF is a 32-bit MIPS M4K microcontroller running up to 40MHz with 128KB of Flash and 16KB of SRAM, housed in a 100-pin TQFP package (14x14 mm). It integrates USB 2.0 Full-Speed, CAN 2.0B, two I2S and four SPI interfaces, three analog comparators, a Charge Time Measurement Unit (CTMU) and a Real-Time Clock Calendar (RTCC), making it a highly integrated general-purpose MCU for connected and human-machine-interface (HMI) designs. What is a PIC32MX microcontroller? PIC32MX is Microchip's family of 32-bit MIPS-based microcontrollers positioned between the 16-bit PIC24F/dsPIC line and the 32-bit Cortex-M based SAM family. In the wider taxonomy it is a microcontroller -> embedded microcontroller -> RISC microcontroller -> MIPS M4K core -> 32-bit MCU -> semiconductor. The PIC32MX series offers higher performance and richer connectivity than 8/16-bit PIC MCUs while remaining compatible with the MPLAB X IDE, Harmony framework, and XC32 toolchain, providing a familiar upgrade path for legacy PIC24/PIC32 customers. Key features of the PIC32MX530F128LT-I/PF include a MIPS32 M4K core delivering up to 83 DMIPS at 50MHz, Peripheral Pin Select (PPS) for flexible pin assignment, a 16-channel 10-bit ADC with 500 ksps conversion rate, four 16-bit timers/counters, and a Parallel Master Port (PMP) with dual buffers for graphics or external memory interfacing. The CTMU allows precise time-of-flight and capacitance-touch measurement, while the RTCC keeps time with calendar function even in low-power modes. Operating voltage is 2.3V to 3.6V across an industrial -40C to +85C temperature range. Typical applications for this device include USB peripherals (HID, CDC, mass storage), CAN-bus industrial nodes, audio playback/capture with I2S codecs, color TFT HMI panels using PMP, capacitive-touch user interfaces via CTMU, and battery-charging controllers. The combination of integrated USB, CAN, and PMP makes it especially attractive for industrial HMI, point-of-sale terminals, automotive infotainment peripherals, and medical instrumentation. When designing with this part, note that the 'T' suffix indicates tape-and-reel packaging, 'I' indicates the industrial -40C to +85C temperature range, and the -I/PF variant runs at the conservative 40MHz speed grade rather than the full 50MHz -50I/PF variant. Pin-compatible PIC32MX5xx family members let designers scale Flash/RAM/peripherals without PCB rework. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, helping procurement and design engineers evaluate the PIC32MX530F128LT-I/PF against second-source candidates and family siblings.

USD $4.69 有现货

PIC32MX530F128LT-V/PF

PIC32MX530F128LT-V/PF - 32-bit MCU, 128KB Flash, USB, 100-TQFP

The Microchip Technology PIC32MX530F128LT-V/PF is a 32-bit MIPS32 M4K microcontroller featuring 128KB Flash and 16KB SRAM, integrated USB 2.0 full-speed, CAN 2.0B, I2S, and CTMU peripherals, housed in a 100-pin TQFP (14x14 mm) package. It operates at up to 40 MHz core frequency, supports an industrial temperature range of -40C to +105C, and is qualified to the AEC-Q100 automotive standard. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a rich set of peripheral interfaces. PIC32MX5xx devices sit at the top of the PIC32MX1/2/5 family hierarchy (PIC32MX1xx/2xx/5xx 64/100-pin Family) and belong to the broader 32-bit MCU -> embedded controller -> microcontroller -> semiconductor taxonomy. They target USB- and CAN-connected embedded designs where deterministic real-time response and a familiar MIPS toolchain are required. Key features include 128KB single-voltage Flash with self-programming support, 16KB SRAM, USB 2.0 full-speed device/host/OTG, two CAN 2.0B modules, an I2S audio interface, a Charge Time Measurement Unit (CTMU) for touch and capacitive sensing, a Real-Time Clock and Calendar (RTCC), and three analog comparators. The 100-pin TQFP exposes up to five UARTs, four SPI ports, five I2C ports, parallel master port, and 10-bit 1 Msps ADC with up to 48 channels. The PIC32MX5xx architecture combines a 5-stage MIPS32 M4K pipeline with single-cycle multiply, hardware divide, and a zero-overhead shadow register set for interrupt latency reduction. The integrated USB, CAN, and 10-bit ADC allow designers to drop an external transceiver companion chip in many node topologies, reducing BOM and PCB area. The CTMU enables capacitive touch sensing for buttons, sliders, and proximity detection without dedicated hardware. Typical applications include automotive infotainment and body controllers (CAN-bus nodes), USB peripherals such as audio interfaces and human-interface devices, industrial control panels with capacitive touch, medical telemetry with USB data logging, and embedded dataloggers requiring RTCC timestamping. The combination of USB device, USB host, and CAN makes it equally comfortable as a peripheral-side or network-node device. When designing with this MCU, allocate the 16KB SRAM carefully: USB descriptors, CAN buffers, and audio sample FIFOs each consume 1-2 KB, leaving roughly 8-10 KB for application code and stack. Use MPLAB Harmony for USB and CAN stacks; legacy MLA is still supported but Harmony is recommended for new designs. Provide a 12 MHz or 24 MHz crystal with proper load capacitor matching to meet USB jitter specifications. This page synthesizes distributor pricing for the PIC32MX530F128LT-V/PF, AEC-Q100 automotive-grade drop-in alternatives within the PIC32MX5xx 100-pin family, USB/CAN peripheral stack notes, and practical design pitfalls not found in the manufacturer datasheet summary.

USD $2.92 有现货

PIC32MX534F064H-I/MR

PIC32MX534F064H-I/MR - 80MHz 32-bit MCU 64KB Flash USB/CAN | Microchip

The Microchip Technology PIC32MX534F064H-I/MR is a 32-bit MIPS32 M4K microcontroller integrating 64 KB of Flash program memory and 16 KB of SRAM, with on-chip USB 2.0 Full-Speed, CAN 2.0B, and 4-channel DMA. It operates up to 80 MHz from a 2.3 V to 3.6 V supply and is housed in a 64-pin 9x9 mm VQFN (MR) package with exposed thermal pad. Background: a microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, volatile data memory, and a rich set of on-chip peripherals such as timers, communication controllers, and analog blocks. The PIC32MX5xx family is a MIPS32 M4K-based line positioned at the high end of Microchip's PIC32 portfolio, adding USB and CAN connectivity for embedded networking. PIC32MX5xx belongs to the broader class of 32-bit flash microcontrollers and inherits the wider PIC32MX1xx/2xx/3xx/4xx/5xx/6xx/7xx family tree. Key features include 64 KB Flash, 16 KB SRAM, an 80 MHz core delivering 1.56 DMIPS/MHz, 4-channel DMA, full-speed USB 2.0 device/host/OTG, CAN 2.0B, five 16-bit timers, two I2C, two SPI, two UART channels, a 16-channel 10-bit ADC at 1 Msps, and four parallel 16-bit comparators. The MR (VQFN-64 9x9) package exposes a thermal pad that reduces junction-to-board thermal resistance. Architecturally, the M4K core executes a 5-stage pipeline with single-cycle multiply and hardware divide, while the peripheral bus matrix allows concurrent DMA transfers between peripherals and RAM without CPU intervention. The 16 KB SRAM is split between general-purpose RAM and dedicated Ethernet/USB/CAN buffer areas. Typical applications include USB peripherals such as HID or CDC class devices, CAN-connected industrial sensor nodes, embedded TCP/IP stacks with the Microchip MLA, low-cost graphic LCD control with the PMP peripheral, and small HMI panels combining USB touch with CAN I/O expansion. Designers should budget for the VQFN exposed-pad PCB layout (thermal vias to the inner ground plane are required for the -I industrial temperature range, -40 to +85 C) and provision a 12 MHz high-speed oscillator plus the 32 kHz low-power crystal for USB full-speed operation. This page consolidates distributor pricing, drop-in same-package alternatives, and practical layout guidance that go beyond the manufacturer datasheet, helping sourcing teams and engineers evaluate PIC32MX534F064H-I/MR in one place.

USD $5.20 有现货

PIC32MX534F064H-I/PT

PIC32MX534F064H-I/PT - 80MHz 32-bit MCU, 64KB Flash, USB, CAN | Microchip

The Microchip PIC32MX534F064H-I/PT is a 32-bit MIPS M4K microcontroller running at 80 MHz (105 DMIPS), housed in a 64-pin TQFP (PT) package measuring 10x10x1 mm. It integrates 64 KB of Flash program memory, 16 KB of SRAM, USB 2.0 On-The-Go with integrated PHY, a CAN 2.0b module with 1024 message buffers, and four dedicated DMA channels, all on a 5-stage pipelined Harvard core with MIPS16e code compression. The -I/PT suffix denotes industrial temperature grade (-40C to +85C) supplied in tray packaging. A 32-bit microcontroller (MCU) is an integrated circuit containing a 32-bit CPU core, non-volatile program memory, volatile data memory, and programmable peripherals on a single die. Within the broader taxonomy, the PIC32MX534F064H belongs to Microchip's PIC32MX5xx/6xx/7xx high-performance family, which bridges 8/16-bit PIC MCUs and 32-bit MIPS/DSP architectures. The MIPS32r2-compatible M4K core uses separate instruction and data buses, delivering deterministic single-cycle execution that simplifies embedded control-loop timing analysis. Key features include USB-OTG full-speed device/host operation without an external PHY, a CAN 2.0b controller with 1024 transmit/receive buffers for industrial and automotive networking, four dedicated DMA channels that offload data movement between peripherals and memory, and MIPS16e mode that reduces code footprint by up to 40% versus full 32-bit instructions. The peripheral set typically includes multiple UART/SPI/I2C ports, a 10-bit ADC with multiple channels, comparators, capture/compare/PWM timers, and a parallel master port for off-chip memory or graphics. Typical applications span USB peripherals, CAN-based industrial nodes, sensor hubs, consumer appliances with USB interfaces, and IoT data-logging. The combination of USB + CAN in a single die makes this part a strong fit for factory-floor gateways, building automation nodes, and human-machine interface controllers that require both PC connectivity and industrial network participation. When designing with this MCU, provide a stable 3.3 V supply, decouple every VDD/VSS pair with 100 nF ceramic plus bulk capacitance within a few mm of the package, and route the USB D+/D- lines as a 90-ohm differential pair. Configure JTAG/ICSP only when needed to reclaim general-purpose I/O. This page synthesizes distributor pricing, drop-in TQFP-64 alternatives, and practical decoupling/layout design notes not found in a single datasheet view, including verified cross-references to compatible PIC32MX devices.

USD $3.95 有现货

PIC32MX534F064H-V/PT

PIC32MX534F064H-V/PT - 80MHz 32-bit MCU, USB/CAN | Microchip

The Microchip Technology PIC32MX534F064H-V/PT is a 32-bit MIPS M4K microcontroller running at 80 MHz (105 DMIPS) with 64 KB flash and 16 KB SRAM, housed in a 64-pin TQFP (10x10 mm) package. The V temperature suffix designates the -40C to +105C industrial/extended operating range. The device integrates USB 2.0 On-The-Go with integrated PHY, CAN 2.0b with 1024 transmit/receive buffers, a 10-bit 1 Msps ADC, and four dedicated DMA channels for USB OTG. A 32-bit MCU is a microcontroller built around a 32-bit datapath, registers, and address bus, allowing single-instruction handling of larger data types and address spaces than 8-bit or 16-bit parts. The PIC32MX5XX/6XX/7XX family uses a 5-stage pipelined Harvard architecture with MIPS16e compressed-code mode, delivering up to 40 percent smaller code size compared to 32-bit instructions. This part sits in the broader product hierarchy: microcontroller -> 32-bit MCU -> MIPS M4K core -> PIC32MX family -> peripheral-rich connectivity tier. Key features include USB OTG with integrated PHY eliminating external transceiver components, CAN 2.0b for industrial networking, four dedicated DMA channels offloading CPU bandwidth for high-throughput peripherals, 80 MHz core with 105 DMIPS performance, and 64 KB flash paired with 16 KB SRAM. The PIC32MX534F064H-V/PT also provides JTAG and 2-wire programming/debug interfaces, up to 53 general-purpose I/O pins, and parallel master port for external bus expansion. The MIPS M4K core executes most instructions in a single cycle, and the Harvard architecture separates instruction and data buses for simultaneous fetch and memory access. Five-stage pipelining enables 1.31 DMIPS per MHz efficiency. The PIC32MX534F064H-V/PT operates from 2.3 V to 3.6 V and includes watchdog timer, real-time clock, and multiple PWM/timer/capture modules for motor and power-control applications. Typical applications include industrial automation and CAN-node controllers, USB peripherals and OTG devices, motor control with feedback sensing, and consumer electronics requiring USB host or device capability. The integrated USB PHY and CAN module reduce BOM cost and PCB footprint for connected embedded designs. Design consideration: the V/PT suffix specifies the extended industrial temperature range; choose I/PT for standard industrial or E/PT for standard commercial. The 64-TQFP package provides generous I/O count (up to 53 GPIO) suitable for parallel master port expansion. This page synthesizes distributor pricing, drop-in PIC32 alternatives, and practical design notes not found in the manufacturer datasheet.

USD $4.92 有现货

PIC32MX534F064HT-I/MR

PIC32MX534F064HT-I/MR - 80MHz 32-bit MCU 64KB Flash USB/CAN | Microchip

The Microchip Technology PIC32MX534F064HT-I/MR is a 32-bit MIPS M4K microcontroller running at 80 MHz with 64 KB of Flash program memory and 16 KB of SRAM, packaged in a 64-pin VQFN (MR) 9x9 mm footprint with an exposed thermal pad. It integrates Full-Speed USB 2.0, CAN 2.0B, four DMA channels, two I2C, two SPI, and five 16-bit timers, plus a 10-bit 1 Msps Analog-to-Digital Converter with up to 16 input channels, making it a dense mixed-signal MCU for connected embedded designs. The 'H' suffix denotes the 64-pin variants of the PIC32MX534 family, the 'T' tape-and-reel orientation, the 'I' industrial -40C to +85C operating temperature range, and the 'MR' package designator from Microchip's ordering code system. The device operates from 2.3 V to 3.6 V and supports 5V-tolerant digital inputs on selected pins for mixed-voltage system integration. A PIC32MX microcontroller is a 32-bit MIPS-based general-purpose MCU from Microchip's PIC32 family, bridging the gap between 8/16-bit PIC microcontrollers and high-end Cortex-M parts. The PIC32MX5xx sub-family specifically targets USB- and CAN-equipped designs, layering Full-Speed USB On-The-Go, a dedicated DMA engine for offloading the engine to peripherals, and a parallel bus for memory-mapped external devices. It sits within the broader hierarchy of MCU -> 32-bit MCU -> MIPS MCU -> PIC32MX family -> PIC32MX5xx sub-family. This positioning explains its widespread use in industrial control, USB peripherals, and CAN-networked sensors where a higher-performance 32-bit core is required without the cost of Cortex-M4 parts. Key features that differentiate this MCU include a 1.25 ns MIPS M4K core pipeline supporting 1.53 DMIPS/MHz and a deterministic interrupt controller, a 10-bit ADC with up to 16 channels and 1 Msps conversion rate, and code-protection Flash with the standard PIC16/32 instruction-set architecture that allows many existing PIC firmware libraries to be ported. The 16 KB RAM is sufficient for moderate USB-class stacks, including CDC, HID, and MSD, while the 64 KB Flash supports full TCP/IP or USB stacks alongside user application code. The PIC32MX534F064H variant also includes a 10-bit ADC, four-wire JTAG for boundary-scan debugging, and two comparators. Its integrated USB 2.0 Full-Speed On-The-Go controller eliminates the need for an external PHY, simplifying BOM cost in human-interface and data-acquisition designs. The 80 MHz core with single-cycle flash prefetch is sufficient for sustained 60+ MIPS operation, and the dedicated DMA engine offloads data movement between peripherals and memory, leaving the core free for application logic. Typical applications for the PIC32MX534F064HT-I/MR include USB human-interface devices (HID) like keyboards and touchscreens, CAN-bus industrial sensor nodes, USB-to-UART bridges, mid-range data loggers, embedded web servers running lwIP or Microchip Harmony TCP/IP, and motor-control feedback processors. Its industrial temperature grade makes it suitable for factory automation nodes and white-goods modes. When designing with this MCU, ensure the VQFN exposed pad is soldered to a sufficient copper pour for thermal dissipation, and add 100 nF decoupling capacitors adjacent to every supply pin. The USB DP/DM traces must be routed as a 90-ohm differential pair on the PCB, and the CAN bus must be terminated with a 120-ohm resistor at each end of the segment. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC32MX5xx family, and practical engineering guidance not found in the standalone datasheet, giving procurement and design engineers a consolidated reference for the PIC32MX534F064HT-I/MR.

USD $3.42 有现货

PIC32MX534F064HT-V/PT

PIC32MX534F064HT-V/PT - 80MHz 32-bit MCU 64KB Flash USB OTG

The Microchip Technology PIC32MX534F064HT-V/PT is a 32-bit MIPS M4K microcontroller operating at 80 MHz with 64 KB Flash and 16 KB SRAM in a 64-pin TQFP (10x10 mm) package, qualified for the -40C to +105C automotive/extended temperature range (V temp suffix). A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O onto one silicon die. The PIC32MX5xx family sits in Microchip's PIC32 portfolio, bridging the gap between 8/16-bit PIC microcontrollers and 32-bit ARM Cortex-M parts. Within the broader hierarchy it belongs to: 32-bit microcontroller -> MIPS M4K core -> PIC32MX5 family -> Microchip 32-bit MCU portfolio -> embedded processing semiconductor. The PIC32MX5 series is well known for built-in USB On-The-Go (OTG) full-speed peripherals, 10-bit ADC, and rich connectivity (UART, SPI, I2C), which is why it persists in industrial, automotive, and connected-embedded designs. Key features of the PIC32MX534F064HT-V/PT include: 64 KB (64K x 8) Flash program memory, 16 KB SRAM, 80 MHz maximum core clock, an integrated USB 2.0 OTG full-speed controller, a 10-bit 1 Msps ADC with up to 16 analog inputs, DMA with multiple independent channels, and five 16-bit timers. The device also supports up to five UART, three SPI, and four I2C peripherals in software-configurable remap configurations, plus parallel master port (PMP) for external bus or display interfacing. Architecturally, the chip uses Microchip's MIPS M4K core with 5-stage pipeline, hardware multiply/divide, and zero-wait-state Flash execution at up to 80 MHz. The integrated USB OTG transceiver eliminates an external PHY for full-speed device/host/OTG roles, saving BOM cost and PCB area. The DMA controller can service peripherals independently of the CPU, enabling deterministic throughput for ADC, USB, UART, and SPI streams - critical for real-time embedded designs. Industrial-grade peripherals such as a real-time clock calendar (RTCC) and watchdog timer are included. Typical applications include USB HID/CDC peripherals, industrial control panels, low-cost graphics HMI with PMP-connected LCDs, automotive body and HMI modules (within the V temp range), sensor aggregation nodes, and small appliances that require deterministic USB connectivity without the cost of an external PHY. The part is also common in legacy industrial designs where the PIC32 ecosystem (MPLAB X IDE, Harmony framework) is required. When designing with this device, pay attention to the decoupling scheme: at least 100 nF plus 10 uF bulk capacitors near the VDD/VSS pins are recommended for USB operation. Ensure the USB D+/D- trace impedance is 90 ohm differential and keep the trace length matched to within 150 mil. Finally, the -V suffix denotes the -40C to +105C operating range - choose -I (-40C to +85C) parts only when the extended high-temp range is not required. This page synthesizes distributor pricing across DigiKey, Mouser and LCSC, drop-in same-package alternatives within the PIC32MX family, and design notes compiled from Microchip datasheets and reference designs that go beyond the manufacturer's basic product page.

USD $3.42 有现货

PIC32MX534F064L-I/BG

PIC32MX534F064L-I/BG - 80MHz 32-bit MIPS MCU 64KB Flash | Microchip

The Microchip Technology PIC32MX534F064L-I/BG is a 32-bit MIPS M4K microcontroller operating at 80 MHz, integrating 64 KB of Flash program memory plus 16 KB of RAM in a 121-ball TFBGA package (10x10 mm). It is a member of the PIC32MX5xx family, which adds USB 2.0 full-speed, CAN, and a 10/100 Ethernet MAC on top of the baseline PIC32MX3/4 feature set. According to the Microchip PIC32MX5XX/6XX/7XX family datasheet, this device targets embedded connectivity, graphics HMI, and industrial control applications. A 32-bit microcontroller (MCU) is a single-chip processor that integrates a CPU core, program Flash, peripherals, and memory into one device. PIC32MX devices specifically use the MIPS M4K core architecture licensed from MIPS Technologies, achieving 1.56 DMIPS/MHz and supporting the MIPS32 instruction set. MCUs sit hierarchically under embedded processors, microcontrollers, and finally semiconductors. Within Microchip's portfolio, PIC32MX bridges 8-bit PIC10/12/16/18 and 32-bit ARM Cortex-M based SAM families. Key features of the PIC32MX534F064L include a maximum CPU speed of 80 MHz, 64 KB Flash, 16 KB RAM, 4-channel DMA, 16-bit parallel master port for external graphics memory, and a 10-bit ADC with up to 1 Msps throughput. Integrated communication peripherals include USB 2.0 full-speed On-The-Go (OTG), two CAN 2.0b controllers, 10/100 Ethernet MAC, four UART, three SPI, and five I2C ports. The device operates from 2.3V to 3.6V and supports industrial -40C to +85C temperature range (I-grade). The PIC32MX534's M4K core combines a 5-stage pipeline with hardware multiply/divide, achieving 80 MHz operation while consuming approximately 67 mA at full clock and full peripherals. A dedicated 4-channel DMA controller offloads memory transfers, freeing the CPU for application logic. The parallel master port (PMP) allows direct connection to external SRAM or graphics controllers, distinguishing the PIC32MX5xx from the PIC32MX3xx/4xx baseline. Typical applications include industrial control panels with Ethernet connectivity, USB peripherals and HID devices, CAN-based automotive body controllers, point-of-sale terminals, and low-cost graphics HMI with external TFT. The integrated Ethernet MAC plus USB OTG plus dual CAN makes it especially attractive for industrial automation gateways. Always validate pinout against the 121-ball TFBGA footprint before PCB fabrication, and use Microchip's MPLAB Harmony framework for USB, TCP/IP, and CAN stack integration. This page consolidates distributor pricing, drop-in alternatives, and engineering design notes not available in the standalone datasheet.

USD $4.35 有现货

PIC32MX534F064L-I/PF

PIC32MX534F064L-I/PF - 80MHz MIPS32 64KB Flash MCU | Microchip

The Microchip PIC32MX534F064L-I/PF is a 32-bit MIPS microcontroller from the PIC32MX5XX/6XX/7XX family, featuring an M4K core running at 80MHz with 105 DMIPS performance, 64KB Flash program memory and 16KB SRAM, packaged in a 100-pin TQFP (14x14x1mm) form factor. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals. The PIC32MX534 belongs to the MIPS32 architecture family — higher-level than PIC24/dsPIC, lower-level than Cortex-M — and Microchip's PIC32MX family is a bridge between 8/16-bit PIC microcontrollers and 32-bit ARM Cortex-M class devices, offering a familiar MPLAB X toolchain. PIC32MX devices integrate USB 2.0 On-The-Go with PHY, CAN 2.0b, multiple DMA channels and parallel master port for graphics and connectivity. Key features of the PIC32MX534F064L-I/PF include USB 2.0 OTG with integrated PHY, four dedicated DMA channels, a 5-stage pipeline Harvard architecture, MIPS16e code compression for up to 40% smaller code size, and an integrated CAN 2.0b module. Operating voltage range is 2.3V to 3.6V with industrial temperature range -40C to +85C. The device integrates a 16-channel 10-bit ADC, multiple UART/SPI/I2C peripherals, a Parallel Master Port (PMP) for graphics or external memory, and up to 85 I/O pins. The 64KB Flash supports self-programming and is partitioned for bootloader use. Typical applications include USB peripherals and HID devices, CAN-based industrial nodes, low-cost graphics HMI with PMP, embedded web servers, and industrial automation controllers. The combination of USB OTG and CAN makes it particularly suited for industrial/automotive networked nodes. When designing with this device, ensure 2.3V-3.6V supply regulation and follow Microchip's PIC32 hardware design checklist for crystal selection and decoupling. Programming is supported through MPLAB X IDE with PICkit 5 / ICD 4 debuggers. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

USD $4.20 有现货

PIC32MX534F064L-I/PT

PIC32MX534F064L-I/PT - 80MHz 32-bit MCU, 64KB Flash, USB/CAN | Microchip

The Microchip Technology PIC32MX534F064L-I/PT is a 32-bit MIPS M4K microcontroller operating at 80 MHz with 64 KB of Flash program memory and 16 KB of RAM, housed in a 100-pin TQFP (12x12 mm) package. This PIC32MX5xx family member integrates on-chip USB 2.0 full-speed, CAN 2.0B, and Ethernet connectivity, making it a high-performance MCU for connected embedded designs. A 32-bit microcontroller (MCU) is a microprocessor integrating a CPU core, program memory (typically Flash), data memory (RAM), and a rich set of on-chip peripherals into a single IC. The PIC32MX family uses the MIPS32 M4K core, which combines deterministic interrupt response with a five-stage pipeline, placing the PIC32MX family in the hierarchy: 32-bit MCU -> embedded microcontroller -> RISC processor -> integrated circuit. This category is widely used wherever an 8-bit MCU is insufficient for processing throughput or peripheral bandwidth. Key features of the PIC32MX534F064L-I/PT include 64 KB Flash with 16 KB RAM, four DMA channels for offloading data movement, an external bus interface with eight-bit Parallel Master Port (PMP) for graphics or external memory expansion, multiple UART/SPI/I2C interfaces, 16-bit timers and a real-time clock. The integrated USB 2.0 full-speed (12 Mbps) on-chip transceiver and CAN 2.0B controller eliminate external PHY chips, reducing BOM cost and PCB area. The device operates from 2.3 V to 3.6 V and supports an industrial temperature range of -40C to +85C. Internal 8 MHz and 32 kHz oscillators allow flexible clocking, and a PLL multiplies the system clock to 80 MHz for demanding workloads. JTAG and two-wire ICSP interfaces enable in-circuit debugging and programming with Microchip MPLAB tools. Typical applications include industrial automation with CAN-bus networking, USB peripherals such as data loggers or human-interface devices, embedded web servers using Ethernet, point-of-sale terminals, and consumer audio products. The combination of high-throughput peripherals and DSP-extensions in the MIPS core suits mixed signal-and-control designs. When designing with this device, ensure the 100-pin TQFP footprint is laid out with proper thermal relief and that decoupling capacitors are placed adjacent to every VDD/VSS pair. Engineers should also evaluate whether the larger PIC32MX5/6/7xx family provides sufficient memory if the application is RAM-bound. This page synthesizes distributor pricing, drop-in alternatives within the PIC32MX family, and practical design notes not found on a single manufacturer datasheet page.

USD $4.95 有现货

PIC32MX534F064L-V/BG

PIC32MX534F064L-V/BG - 80MHz MIPS32 M4K MCU, 64KB Flash, USB-OTG | Microchip

The Microchip Technology PIC32MX534F064L-V/BG is a 32-bit MIPS32 M4K microcontroller operating at up to 80 MHz, integrating 64 KB of Flash program memory and 16 KB of SRAM in a 121-pin TFBGA (10x10 mm, 0.8 mm pitch) package. It features a USB-OTG controller, a CAN 2.0B module, a 10-bit 1 Msps ADC with up to 16 channels, and a dedicated DMA controller for CPU-offloaded data movement. The -V suffix denotes the extended -40C to +105C operating temperature range suitable for industrial and AEC-Q100-adjacent designs. A microcontroller (MCU) is an integrated circuit that combines a CPU core, volatile and non-volatile memory, and a rich set of peripherals on a single die, forming the compute backbone of embedded systems. PIC32MX5xx devices sit within Microchip's PIC32 family (a superset of MIPS32 M4K cores) and belong to the broader 32-bit MCU segment of the power-management and embedded-control hierarchy. They typically follow an LDO -> linear regulator -> voltage regulator -> power management IC-style of on-chip power management, supplying internal logic rails from a single 2.3 V to 3.6 V external supply. Key differentiating features of the PIC32MX534F064L-V/BG include its combination of full-speed USB-OTG (with on-chip transceiver and dedicated DMA channels), integrated CAN 2.0B, parallel master port (PMP) for external bus interfacing, and five 16-bit timers/compare-capture-PWM modules. The 80 MHz core delivers 1.56 DMIPS/MHz (MIPS32 M4K superscalar architecture), sufficient for TCP/IP stacks and modest DSP-style signal processing. Code execution is accelerated by a prefetch cache and a tightly-coupled RAM region to hide Flash latency. Typical applications include industrial USB-to-CAN bridges, factory automation nodes, HMI panels with PMP-driven TFTs, low-cost motor-control front-ends, and USB peripherals such as data loggers and HID devices. The 121-ball BGA package supports high-density PCB layouts while maintaining access to the full peripheral set. When designing with this device, ensure the 0.8 mm pitch BGA is matched to a PCB with appropriate via-in-pad or dog-bone fan-out to keep routing manageable. The -V variant's +105C ceiling allows placement near heat sources but still requires thermal derating above sustained 70 mA GPIO loads. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that the bare Microchip datasheet does not aggregate, helping engineers select the right part faster.

USD $4.60 有现货

PIC32MX534F064L-V/PF

PIC32MX534F064L-V/PF - 80MHz 32-bit MCU w/ USB OTG | Microchip

The Microchip Technology PIC32MX534F064L-V/PF is a 32-bit MIPS M4K microcontroller running at 80 MHz, integrating 64 KB Flash and 16 KB SRAM in a 100-pin TQFP (14x14 mm) package. The -V suffix denotes the Vdd range of 2.3V-3.6V, and the -PF suffix identifies the 100-TQFP industrial/leaded package option. A 32-bit microcontroller (MCU) is an integrated processor core, memory, and peripherals designed for embedded control. PIC32MX MCUs belong to the MIPS32 M4K architecture family, which bridges the gap between traditional 8/16-bit PIC microcontrollers and high-performance ARM Cortex-M devices, sitting in the system hierarchy as: PIC32MX -> 32-bit MCU -> MIPS M4K MCU -> embedded microcontroller -> semiconductor. The PIC32MX5xx family specifically adds USB OTG, CAN, and 10-bit ADC peripherals, making it the mainstream connectivity option within the broader PIC32 portfolio. Key features include: 64 KB Flash (64K x 8) and 16 KB SRAM, full-speed USB 2.0 OTG with integrated transceiver, two I2C, two SPI, two UART channels, a 16-channel 10-bit ADC at 1 Msps, five 16-bit timers, a Real-Time Clock and Calendar (RTCC) with alarm, a Fail-Safe Clock Monitor, and a watchdog timer with a dedicated RC oscillator. The device is pin-compatible with 16-bit PIC24/dsPIC devices and other PIC32MX variants, allowing migration without PCB rework. Architecture-wise, the MIPS M4K core delivers 1.56 DMIPS/MHz (Dhrystone 2.1) and supports the MIPS16e instruction set for improved code density. The peripheral bus runs at the system clock divided by 1, with up to 16 DMA channels available for memory-to-memory or peripheral-to-memory transfers without CPU intervention. A 4-channel hardware DMA engine accelerates USB, ADC, and SPI transactions. Typical applications include USB peripherals (HID, CDC, mass storage), industrial control panels, embedded CAN nodes, sensor hubs, low-cost graphical interfaces, and home automation controllers. Designers select this part when USB connectivity, CAN, or substantial peripheral mix is required without the cost of Cortex-M3/M4 silicon. When laying out the PCB, dedicate a clean ground plane under the VAD die area, place a 1uF + 100nF decoupling pair within 5 mm of each VDD/VSS pin pair, route the USB DP/DM pair as a 90 ohm differential and avoid routing them near switching converters or oscillator traces. This page synthesizes drop-in replacement parts, parametric comparisons, and practical design notes not found in the manufacturer datasheet alone.

USD $4.12 有现货

PIC32MX534F064L-V/PT

PIC32MX534F064L-V/PT - 32-bit MCU 64KB Flash USB OTG | Microchip

The Microchip Technology PIC32MX534F064L-V/PT is a 32-bit MIPS M4K microcontroller operating at 80 MHz delivering 105 DMIPS, integrated with 64 KB Flash and 16 KB SRAM, housed in a 100-pin TQFP (12x12 mm) package with USB 2.0 On-The-Go (OTG) peripheral including integrated PHY. It belongs to the PIC32MX5XX/6XX/7XX family and supports industrial temperature grade (-40C to +105C), as indicated by the -V/ suffix. A 32-bit microcontroller (MCU) is a microprocessor-on-a-chip integrating CPU core, program memory (Flash), data memory (SRAM), and a rich peripheral set in a single device. Within the semiconductor taxonomy, MCUs sit under microcontrollers -> embedded processors -> digital ICs -> semiconductors. The PIC32MX534F064L is positioned as a connectivity-focused MCU thanks to integrated USB OTG, CAN 2.0b, and multi-channel DMA optimized for high-bandwidth peripheral traffic. Key features include 64 KB (64K x 8) Flash program memory, 16 KB SRAM, USB 2.0 OTG with integrated PHY and 4 dedicated DMA channels, CAN 2.0b module with 1024 transmit/receive buffers, a 5-stage pipeline Harvard architecture with MIPS16e mode for up to 40% smaller code size, two I2C, two SPI, two UART serial modules, a 10-bit 1 Msps ADC with up to 16 channels, four 16-bit timers, a Real-Time Clock and Calendar (RTCC) with alarm, and a Fail-Safe Clock Monitor that allows safe shutdown if the primary clock fails. Architecturally, the MIPS32 M4K core uses a 5-stage pipeline with separate instruction and data buses (Harvard) plus MIPS16e compressed instruction support, enabling 105 DMIPS at 80 MHz while reducing code footprint by up to 40%. The peripheral DMA engine (8 channels) offloads USB, CAN, and ADC transactions from the CPU, allowing deterministic real-time throughput for embedded connectivity stacks. Typical applications include USB peripherals (HID, CDC, mass storage, audio class), industrial CAN nodes, motor control and BLDC drives, embedded web servers, and POS terminals. The combination of native USB OTG, CAN, and 10-bit ADC makes it well suited for industrial HMI panels and automotive aftermarket dashboards. When designing with this device, allocate PCB area for the 32.768 kHz crystal and load capacitors, and follow Microchip application note AN1160 for USB OTG PCB layout including 90-ohm differential routing on D+/D-. Decouple each VDD/VSS pair with a 100 nF ceramic placed within 3 mm of the pin, plus a bulk 10 uF tantalum on the main rail. This page synthesizes distributor pricing, same-brand drop-in alternatives (other PIC32MX534F064 and PIC32MX534F064H variants), and practical USB OTG design notes not found in the manufacturer datasheet alone.

USD $5.12 有现货

PIC32MX534F064LT-I/PF

PIC32MX534F064LT-I/PF - 80MHz 32-bit MCU, 64KB Flash, USB/CAN | Microchip

The Microchip PIC32MX534F064LT-I/PF is a 32-bit MIPS M4K microcontroller running at 80 MHz with 64 KB Flash and 16 KB SRAM, packaged in a 100-pin TQFP (14x14 mm, 1 mm thick). It integrates full-speed USB 2.0, CAN 2.0B, 4 DMA channels, and a rich peripheral set including UART/SPI/I2C and a 16-bit Parallel Master Port, targeting industrial and embedded control designs. A PIC32MX microcontroller is a 32-bit MCU family from Microchip built on the MIPS32 M4K core architecture. It bridges the gap between 8/16-bit PIC microcontrollers and high-performance ARM Cortex-M parts by offering 32-bit computational throughput, large linear address space, and deterministic interrupt handling while preserving the MPLAB ecosystem (XC32 toolchain, Harmony framework, MPLAB X IDE). The "32MX" family is positioned for connected-embedded applications that need USB, CAN, Ethernet or Ethernet-ready peripherals along with moderate DSP performance. Key features of the PIC32MX534F064LT-I/PF include 64 KB Flash program memory, 16 KB SRAM, an 8-channel 10-bit 1 Msps ADC, five 16-bit timers/capture/compare/PWM modules, two I2C and two SPI/I2S ports, two UARTs with IrDA support, full-speed USB 2.0 (Device/Host/OTG), CAN 2.0B, four-channel DMA, and an internal 8 MHz Fast RC oscillator with PLL. The "T" suffix denotes tape-and-reel packaging and the "-I/PF" suffix denotes industrial temperature grade (-40C to +85C) in the 100-pin TQFP package. Architecturally, the M4K core provides a 5-stage pipeline, hardware multiply/divide, single-cycle MAC, and a tightly-coupled prefetch cache, which together with the bus-matrix DDR-style peripheral interconnect delivers deterministic throughput at 80 MHz. The peripheral set (USB + CAN + 4 DMA) is well-matched to industrial protocols and human-interface designs. Typical applications include industrial control and HMI panels, USB peripherals and CAN node gateways, motor control and BLDC/PMSM drivers, embedded dataloggers, sensor hubs, and low-cost audio processing. The combination of USB device/host, CAN, and DMA makes it a flexible connectivity MCU for factory automation. When designing with the PIC32MX534F064LT-I/PF, allocate decoupling capacitance (100 nF plus 4.7 uF bulk) within 5 mm of each power pin, route the 80 MHz system trace as a 50 ohm microstrip with reference-plane stitching, and bias the internal 8 MHz FRC plus PLL if precise USB or CAN timing is required - the USB module requires 48 MHz +/- 0.25% to meet USB 2.0 full-speed accuracy. This page synthesizes distributor pricing (DigiKey/Mouser/Octopart), drop-in alternatives within the PIC32MX5xx family, and practical PCB and firmware design notes not found in the manufacturer datasheet, optimized for engineers sourcing production-grade 32-bit MCUs.

USD $5.96 有现货

PIC32MX534F064LT-I/PT

PIC32MX534F064LT-I/PT - 80MHz 32-bit MCU 64KB Flash | Microchip

The Microchip Technology PIC32MX534F064LT-I/PT is a 32-bit MIPS32 M4K microcontroller operating up to 80 MHz, integrating 64 KB of flash program memory and 16 KB of SRAM in a 100-pin TQFP (12x12x1 mm) package. The part ships in tape-and-reel (T) packaging and is rated for the industrial -40C to +85C temperature range (I-grade). It includes integrated USB 2.0 full-speed and CAN 2.0b peripherals, four DMA channels, and the standard PIC32MX5xx analog/mixed-signal feature set. A 32-bit microcontroller (MCU) is a programmable processor core that executes instructions from on-chip flash memory, integrates RAM and a broad set of peripherals (USB, CAN, timers, ADC, I/O), and forms the central controller in an embedded system. Within the PIC32MX family, the MX5xx sub-family is positioned above the MX1/MX2 value line and below the MX6/MX7 high-performance line, targeting USB- and CAN-equipped industrial, medical, and consumer applications that benefit from MIPS M4K processing throughput. Key features of this part include the 80 MHz MIPS32 M4K core with 5-stage pipeline, hardware multiply/divide, single-cycle multiplication, prefetch cache, and 64 KB flash that supports live updates through the ICSP interface. The 16 KB SRAM allows reasonable data buffering without external memory, while the four DMA channels offload data movement from the CPU. The USB 2.0 full-speed on-chip transceiver and the CAN 2.0b controller reduce external component count. The 100-pin TQFP package exposes up to 85 general-purpose I/O pins and supports parallel master port (PMP) operation for external bus expansion. Typical applications include industrial USB-to-CAN bridges, HMI panels with USB device connectivity, embedded dataloggers, medical instrument controllers, and general-purpose 32-bit nodes in factory automation networks. The combination of USB device, CAN, and ample I/O makes this MCU a strong fit for industrial nodes that must communicate with both a host PC and a CAN fieldbus. Designers should plan for a 3.3V core supply with typical 2.0V-3.6V operating range, place a 10 uF plus 0.1 uF decoupling network near each power pin pair, and follow Microchip's USB hardware design guidelines (impedance-controlled 90 ohm differential routing, common-mode choke) when the USB peripheral is enabled. The 'T' suffix indicates tape-and-reel, so pick-and-place programming and full production-line rework should follow standard JEDEC MSL-3 handling.

USD $5.10 有现货

PIC32MX534F064LT-V/BG

PIC32MX534F064LT-V/BG - 32-bit MCU 80MHz 64KB Flash USB OTG | Microchip

The Microchip Technology PIC32MX534F064LT-V/BG is a 32-bit microcontroller built on the MIPS32 M4K core, operating up to 80 MHz, integrating 64 KB of Flash program memory and 16 KB of SRAM in a 121-ball TFBGA (10x10 mm) package. The "L" suffix denotes the low-pin-count USB OTG variant and the "T" indicates tape-and-reel packaging; "V/BG" specifies the V temperature grade with the TFBGA package option. The part includes a 10-bit 1 MSPS ADC, DMA controller, USB 2.0 full-speed OTG, I2C, SPI, UART, PMP, and up to 53 general-purpose I/O lines, enabling single-chip solutions for cost-sensitive embedded designs. A 32-bit microcontroller (MCU) is a microprocessor core optimized for embedded control, integrating CPU, memory, peripherals, and interrupt logic into a single IC. The PIC32MX534 family belongs to the broader MIPS32 architecture family, which sits in the taxonomy microcontroller -> embedded processor -> integrated circuit -> semiconductor. This 32-bit class offers deterministic real-time performance, larger address space, and richer peripheral integration compared to 8/16-bit MCUs while remaining significantly lower in cost than Cortex-M4 application processors. Key differentiating features include hardware DMA that offloads data movement from the CPU, full-speed USB OTG with on-chip transceiver that eliminates external PHY cost, and a 10-bit ADC capable of 1 MSPS for high-speed sensor sampling. The 80 MHz M4K core delivers 1.56 DMIPS/MHz and executes most instructions in one clock cycle, suitable for control loops, USB stacks, and graphical user interfaces with external peripherals. The device supports 2.3V to 3.6V single-supply operation, includes a Real-Time Clock calendar, and offers multiple low-power modes for battery-powered designs. Architecturally the PIC32MX5 family uses a Harvard-style memory structure with separate 32-bit instruction and data paths to the Flash and SRAM. The DMA controller supports up to 8 independent channels and triggers on peripheral events, allowing continuous USB or ADC operation without CPU intervention. The USB OTG module includes the physical layer, requiring only an external pull-up or pull-down resistor on the D+/D- lines and a few decoupling components for a compliant USB port. The part fits inside industrial control panels, USB peripherals, point-of-sale terminals, sensor hubs, medical data loggers, and consumer audio accessories. The compact 121-ball TFBGA package suits space-constrained PCB layouts such as wearable dongles and portable test instruments where a QFP would be too tall or too large. Designers select the PIC32MX534 family when balancing USB integration, deterministic interrupt latency, and Microchip's MPLAB Harmony firmware ecosystem against the lower cost of 8-bit PIC16/PIC18 parts. When designing with this device, plan for decoupling (100 nF + 1 uF near each VDD pair), keep the USB trace length under 50 mm with 90-ohm differential impedance, and configure the oscillator PLL that enables ripple-free USB clocks without overshoot. The MPLAB Harmony configurator and the PICkit 5 in-circuit debugger are the recommended toolchain for production programming and firmware development, providing validated peripheral drivers and a USB stack. This page synthesizes distributor pricing for the PIC32MX534F064LT-V/BG, drop-in alternatives within the same 121-ball TFBGA footprint, and practical layout and USB design notes that the manufacturer datasheet does not present in a single reference.

USD $4.15 有现货

PIC32MX534F064LT-V/PF

PIC32MX534F064LT-V/PF - 80MHz 32-bit MCU, 64KB Flash, USB OTG | Microchip

The Microchip PIC32MX534F064LT-V/PF is a 32-bit MIPS32 M4K microcontroller IC running at 80 MHz, integrating 64 KB of Flash program memory and 16 KB of SRAM, housed in a 100-pin TQFP (14x14 mm) package. It belongs to the PIC32MX5xx family, which adds a USB On-The-Go (OTG) full-speed peripheral, a 10-bit 1 Msps ADC with up to 16 channels, four DMA channels, and a CAN 2.0B controller alongside the standard PIC32MX peripherals. The '-V' suffix denotes the automotive-grade -40C to +105C operating temperature range, and the trailing 'T' indicates tape-and-reel packaging. A PIC32MX microcontroller is a MIPS-based 32-bit MCU that bridges 8/16-bit PIC legacy code to full 32-bit performance at low power. The MIPS32 M4K core executes most instructions in a single cycle, giving 1.56 DMIPS/MHz and deterministic interrupt latency. The PIC32MX5xx family sits in Microchip's mid-tier MCU hierarchy: PIC10/12/16/18 (8-bit) -> PIC24/dsPIC33 (16-bit) -> PIC32MX (32-bit) -> PIC32MZ/32MK (32-bit high performance) -> 32-bit ARM Cortex-M0+/M4/M7 (SAM). PIC32MX parts share a unified MPLAB X toolchain, Harmony framework, and peripheral library across the family. Key features of the PIC32MX534F064LT-V/PF include: 80 MHz CPU clock, 64 KB Flash with live update support, 16 KB SRAM, USB 2.0 full-speed OTG, CAN 2.0B, 10-bit 1 Msps ADC, four DMA channels, five 16-bit timers, two I2C, two SPI, and five UART. The integrated 8 MHz internal RC and 4x PLL allow flexible clocking. The 100-pin TQFP exposes 85 GPIO, ideal for HMI, motor-control and connectivity gateways. Typical applications are automotive body and infotainment modules, USB peripherals (HID, CDC, mass storage), industrial sensors with CAN-bus aggregation, and consumer audio accessories. Designers choose this part when they need a wide-temperature automotive-grade MCU with on-chip USB OTG and CAN without an external transceiver for low-speed CAN. The V/PF package is the 100-pin TQFP - for compact designs, the 64-pin TQFP (PT) variant PIC32MX534F064LT-V/PT provides the same silicon in a smaller footprint.

USD $4.55 有现货

PIC32MX550F256H-50I/MR

PIC32MX550F256H-50I/MR - 50MHz 256KB Flash 32-bit MCU | Microchip

The Microchip Technology PIC32MX550F256H-50I/MR is a 32-bit MIPS M4K microcontroller with 256 KB Flash and 64 KB SRAM, operating up to 50 MHz (83 DMIPS), housed in a 64-pin QFN (9x9 mm) package with industrial -40C to +85C temperature rating. This part is part of the PIC32MX1XX/2XX/5XX 64/100-pin family and integrates USB 2.0 Full-Speed OTG, CAN 2.0B, up to three I2S/SPI modules for codec interfaces, and a Parallel Master Port (PMP) with dual read/write buffers for graphics. A 32-bit microcontroller (MCU) is an integrated processor core, program memory, data memory, and peripherals on a single die. Within the broader taxonomy of embedded semiconductors, this device belongs to the application-specific microcontroller category, which itself sits inside the integrated circuit (IC) hierarchy of power-managed mixed-signal processors used in embedded systems. Microcontrollers in the PIC32MX class target HMI (human-machine interface) applications with audio, graphics, and touch peripherals. Key differentiating features include Peripheral Pin Select (PPS) for flexible signal routing, dual CAN 2.0B modules with DeviceNet addressing, 16-channel 10-bit ADC at 1 Msps, and a Charge Time Measurement Unit (CTMU) for capacitive touch. The integrated USB 2.0 Full-Speed OTG controller enables device/host/OTG roles without external PHY. The 64-pin QFN package supports compact PCB layouts while exposing ample I/O for parallel interfaces. Architecturally, the device uses a MIPS32 M4K Harvard-style core with 5-stage pipeline, separate instruction and data paths, hardware multiply/divide, and zero overhead looping. The 50 MHz core provides 83 DMIPS, sufficient for protocol stacks and moderate DSP loads. The integrated DMA controller offloads data movement from the CPU. Typical applications include industrial control with CAN bus connectivity, USB-based human interface devices, audio playback systems using I2S codecs, and low-cost graphics terminals with PMP-driven LCDs. The PPS remapping and dual CAN modules make it suitable for automotive body electronics and building automation. When designing with this MCU, allocate at least one 10uF bulk and one 0.1uF decoupling capacitor adjacent to each power pin pair, route the 50 MHz crystal traces symmetrically, and use a 4-layer PCB with continuous ground pour under the QFN thermal pad to manage dissipation. This page consolidates distributor pricing, drop-in same-package alternates, and practical design considerations beyond the manufacturer datasheet to accelerate sourcing and design-in decisions.

USD $3.85 有现货

PIC32MX550F256H-50I/PT

PIC32MX550F256H-50I/PT - 50MHz 32-bit MCU 256KB Flash | Microchip

The Microchip Technology PIC32MX550F256H-50I/PT is a 32-bit MIPS32 M4K microcontroller running up to 50 MHz delivering 83 DMIPS, with 256 KB Flash and 32 KB SRAM, integrated Full-Speed USB 2.0 OTG, CAN 2.0B with DeviceNet addressing, three I2S/SPI modules, and a Parallel Master Port (PMP) with dual buffers for graphics interfaces, all housed in a 64-pin TQFP (PT) 10x10 mm package. The Industrial (-I) suffix specifies an operating temperature range of -40C to +85C, while the -50 suffix confirms the 50 MHz top speed grade. The PIC32MX5XX family bridges mainstream 8/16-bit PIC designs to full 32-bit processing with Peripheral Pin Select (PPS) remapping for flexible board layouts. A 32-bit microcontroller is a programmable system-on-chip that integrates a CPU core, volatile and non-volatile memory, and a rich set of peripherals (timers, ADC, communication interfaces) on a single silicon die. The PIC32MX family is a key node in Microchip's product taxonomy: it sits above the 16-bit PIC24/dsPIC families and below the Cortex-M class SAM and PIC32MK parts. Designers choose PIC32MX when they want Microchip's MPLAB X toolchain maturity and PPS flexibility without paying for the higher-pin-count or higher-speed PIC32MZ/MK families. Key features of the PIC32MX550F256H-50I/PT include 256 KB Flash program memory, 32 KB SRAM data memory, a 10-bit 1 Msps ADC with up to 28 analog channels, five 16-bit timers, two I2C ports, two UARTs, three SPI modules, two I2S modules for audio codecs, USB 2.0 Full-Speed OTG with on-chip transceiver, a CAN 2.0B module with DeviceNet addressing, and the PMP graphics master port with dual read/write buffers that offload bus cycles from the CPU. Charge Time Measurement Unit (CTMU) provides capacitive touch and basic analog front-end functions, while PPS remaps most digital peripherals to any compatible I/O pin. The architecture uses a 5-stage MIPS M4K pipeline with hardware multiply/divide and a tightly coupled prefetch cache that mitigates Flash wait states at 50 MHz. The 3.3V core supply with internal regulators lets the device run directly from a 2.3V to 3.6V rail, simplifying power tree design. On-chip debug over JTAG or 2-wire programming via ICSP is supported throughout the family. Typical applications include USB peripherals and HID devices, CAN-connected industrial nodes with DeviceNet, HMI/graphic display controllers via PMP, audio streaming with I2S codecs, capacitive touch user interfaces using CTMU, and low-cost connectivity bridges for sensors. The combination of USB, CAN, and PMP also fits automotive telematics, building automation controllers, and point-of-sale terminals. A key design consideration: at 50 MHz the Flash access wait states must be configured via the system registers, and PMP timing for graphics requires careful setup of the data setup and hold registers - consult the family reference manual section on PMP for your chosen panel. Vcap pin must be left unloaded except for the required 10 uF decoupling. This page synthesizes distributor pricing, drop-in alternatives drawn from the same Microchip PIC32MX5XX family, and practical design notes not duplicated in the manufacturer datasheet.

USD $3.05 有现货

PIC32MX550F256H-I/PT

PIC32MX550F256H-I/PT - 32-bit MCU 256KB Flash 64-TQFP | Microchip

The Microchip Technology PIC32MX550F256H-I/PT is a 32-bit RISC microcontroller based on the MIPS32 M4K core, offering up to 50 MHz / 83 DMIPS performance, 256 KB of Flash program memory, and 32 KB of SRAM in a 64-pin TQFP (10x10 mm) package. The device integrates two I2S and four SPI modules for audio codec and serial communication, Peripheral Pin Select (PPS) for flexible I/O mapping, and a Parallel Master Port (PMP) with dual buffers for graphics interfaces. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and a rich set of peripherals such as timers, communication interfaces, ADCs, and GPIO into one package. The PIC32MX family sits within the broader hierarchy: microcontroller -> embedded processor -> semiconductor device. The M4K core provides a 32-bit Harvard architecture with single-cycle multiplication, deterministic interrupts, and DSP-oriented instructions, making it well suited to embedded applications requiring higher computational throughput than 8/16-bit MCUs. Key features include 256 KB Flash with 32 KB RAM, 16-channel 10-bit ADC at up to 1 Msps, USB 2.0 full-speed On-The-Go (OTG), two I2C, two UART, two I2S, four SPI, six 16-bit timers, five input-capture and five output-compare modules, a Real-Time Clock/Calendar (RTCC) with calendar mode, and a Charge Time Measurement Unit (CTMU) for capacitive touch sensing. The device supports an industrial operating temperature range of -40C to +85C. Typical applications span audio playback and processing, USB peripherals (HID, CDC, MSD, audio class), HMI panels with graphics and touch, motor control (BLDC/PMSM FOC), industrial sensing, data loggers, and home appliances. The combination of PMP for LCD control, I2S for digital audio streams, CTMU for touch keys, and USB OTG enables single-chip HMI + audio + connectivity products. When designing with this part, allocate decoupling capacitors near each power pin pair (VDD/VSS and AVDD/AVSS), follow Microchip's recommended ICSP programming footprint, and verify PPS mappings in the Harmony/MPLAB-X configuration tool. For RTCC operation, the 32.768 kHz crystal layout must observe Microchip's oscillator guidelines.

USD $3.48 有现货

PIC32MX550F256HT-50I/MR

PIC32MX550F256HT-50I/MR - 50MHz 32-bit MCU 256KB Flash | Microchip

The Microchip Technology PIC32MX550F256HT-50I/MR is a 32-bit microcontroller from the PIC32MX5xx family, featuring the MIPS32 M4K core running at up to 50 MHz (83 DMIPS). It integrates 256 KB of Flash program memory and 32 KB of SRAM, packaged in a 64-pin QFN (9x9 mm) form factor with an exposed thermal pad for enhanced thermal dissipation. A 32-bit microcontroller (MCU) is a single-chip computer that combines a 32-bit processor core, program and data memory, and a rich set of on-chip peripherals. Within the broader embedded semiconductor hierarchy it sits between 8/16-bit MCUs and application processors, offering high computational throughput (MIPS/DMIPS) while retaining deterministic real-time interrupt behavior. The PIC32MX5xx family targets cost-sensitive connected and graphical embedded applications where MIPS-class performance is required without moving to Cortex-M class pricing. Key features include two I2S audio interfaces, four SPI modules, peripheral pin select (PPS) for flexible signal routing, a parallel master port (PMP) with dual read/write buffers for graphics, an integrated charge time measurement unit (CTMU), USB 2.0 full-speed OTG, a 10-bit ADC, and multiple UART/I2C channels. The 50 MHz core delivers 83 DMIPS, and the memory sub-system pairs 256 KB Flash with 32 KB SRAM for code and data-heavy audio/display use cases. Architecturally, the device is built around the MIPS32 M4K Harvard core with a 5-stage pipeline, hardware multiply/divide, and zero-overhead looping, giving it strong C-language code density versus ARM Cortex-M0/M0+ at similar MHz. The PPS block decouples digital peripheral I/O from physical pins, allowing designers to remap UART/SPI/I2S onto most digital I/Os on the fly. The 64-QFN with EP enables compact PCB layouts suitable for space-constrained designs. Typical applications include USB audio bridges, Bluetooth/wireless audio docks, low-cost graphical HMI panels, motor control BLDC/PMSM boards, and consumer IoT hubs. It is well suited where the design needs MIPS-class code compatibility, I2S audio capture/playback, and PMP-based LCD driving simultaneously. When designing with this MCU, ensure the exposed pad is soldered to a sufficiently large copper pour for thermal relief and ground reference. Configure PPS mappings carefully because peripheral-to-pin assignments are device-dependent; consult the datasheet pin tables before board layout. Use the on-chip CTMU for capacitance touch or precise time-of-flight sensing rather than adding an external timer IC. This page synthesizes distributor pricing, same-brand drop-in alternatives in the same 64-QFN package, comparison parameters, and practical design notes not found in the manufacturer datasheet alone.

USD $3.40 有现货

PIC32MX550F256HT-V/PT

PIC32MX550F256HT-V/PT - 32-bit MCU 256KB Flash 64-TQFP | Microchip

The Microchip Technology PIC32MX550F256HT-V/PT is a 32-bit MIPS32 M4K microcontroller with 256 KB Flash and 32 KB SRAM, housed in a 64-pin TQFP (10x10 mm) package. It operates at up to 50 MHz/83 DMIPS with a 3.3 V supply and integrates two I2S modules, four SPI, USB, CAN, three comparators, CTMU, and RTCC peripherals. A 32-bit microcontroller (MCU) is an integrated computing device that executes instructions from a 32-bit-wide architecture. PIC32MX parts sit in Microchip's MIPS-based MCU family, which has historically delivered deterministic interrupt latency and easy C-language development via MPLAB X IDE. The PIC32MX5xx sub-family specifically adds USB 2.0 full-speed, CAN 2.0B, and Peripheral Pin Select (PPS) remapping, bridging cost-sensitive 8/16-bit designs and high-performance Cortex-M parts. Key features include 256 KB single-cycle Flash, 32 KB SRAM, up to 50 MHz core clock with 83 DMIPS, Peripheral Pin Select (PPS) for flexible peripheral-to-pin mapping, Parallel Master Port (PMP) for graphics and external memory, and an automotive AEC-Q100 qualified "V" temperature grade (-40C to +125C). The CTMU provides touch sensing, capacitive measurement, and time-of-flight capability with no external components. USB and CAN make this part a drop-in fit for industrial-control and automotive sub-network nodes. The architecture uses a 5-stage MIPS32 M4K pipeline with separate instruction and data buses (Harvard), single-cycle hardware multiply, and zero-wait-state Flash access up to 50 MHz. The M4K core includes a prefetch cache that reduces flash access penalty at high bus speeds, while the configurable prefetch module lets the user balance determinism versus throughput. Typical applications include USB peripherals, CAN-bus node controllers, industrial automation HMI with PMP-driven LCDs, automotive body controllers in the AEC-Q100 grade, capacitive-touch user interfaces using CTMU, and audio streaming via I2S. The wide peripheral set reduces BOM count by integrating USB-PHY transceivers, CAN transceivers interface logic, and audio serial ports on-chip. When designing with the PIC32MX550F256HT-V/PT, use the V grade only if the application requires the -40C to +125C automotive window; otherwise the I grade (PIC32MX550F256H-I/PT) at -40C to +85C is more cost-effective for industrial and consumer designs. This page synthesizes distributor pricing, drop-in alternatives sourced from Microchip's PIC32MX family, and practical design notes that are not collocated in the manufacturer datasheet, offering a faster engineering decision path.

USD $2.41 有现货

PIC32MX550F256L-50I/PF

PIC32MX550F256L-50I/PF - 50MHz 32-bit MCU 256KB Flash | Microchip

The Microchip Technology PIC32MX550F256L-50I/PF is a 32-bit MIPS M4K microcontroller running up to 50 MHz (83 DMIPS) with 256 KB Flash and 32 KB SRAM, housed in a 100-pin TQFP (14x14 mm) package. It integrates USB 2.0 Full-Speed OTG, CAN 2.0B, two I2S and four SPI modules, a Parallel Master Port (PMP) with dual read/write buffers for graphics, Peripheral Pin Select (PPS), and the Charge Time Measurement Unit (CTMU) for touch and HMI sensing. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals on a single die. Within the broader semiconductor taxonomy, an MCU belongs to the class of embedded processors, which sits under microcontrollers and then under integrated circuits (ICs). The PIC32 family uses a RISC (Reduced Instruction Set Computer) MIPS32 core and is positioned for higher-performance 32-bit embedded applications. Key features include USB 2.0 Full-Speed OTG with on-the-go host/device capability, CAN 2.0B active with DeviceNet addressing support, four I2S/SPI selectable modules, a 16-channel 10-bit ADC (1 Msps), and an operating voltage range of 2.3V to 3.6V. Industrial temperature range of -40C to +85C and the 100-pin TQFP footprint expose up to 78 GPIO-capable I/O pins, enabling connectivity-rich designs without external expanders. Architecturally, the PIC32MX5XX uses the MIPS32 M4K 32-bit core with a 5-stage pipeline and hardware multiply/divide, providing deterministic interrupt latency and predictable real-time performance. The CTMU provides constant-current source/sink capability for capacitive touch and ultrasonic measurement, and the PMP with dual buffers sustains continuous graphics frame updates without CPU intervention. Typical applications include USB peripherals and embedded hosts, CAN-connected industrial nodes, audio codec DSP front-ends, HMI panels with graphics and touch, and sensor hubs with USB-CDC virtual COM ports. The combination of USB, CAN, and PMP makes this MCU a single-chip solution for industrial/automotive HMI gateways. When designing with this device, ensure decoupling per the manufacturer datasheet (low-ESR ceramic, resonance above 20 MHz), and verify PPS remapping constraints for each peripheral. Programming requires MPLAB X IDE with XC32 compiler; ICSP and JTAG are supported. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $3.18 有现货

子分类

产品（32725)