集成电路

子分类

📁 ADC/DAC 2518 产品 📁 放大器IC 793 产品 📁 音频编解码器 16 产品 📁 音频IC 2 产品 📁 时钟与计时 287 产品 📁 DSP 962 产品 📁 数据采集IC 2 产品 📁 数字电位器 4 产品 📁 显示驱动与控制器 1 产品 📁 FPGA与CPLD 6666 产品 📁 接口IC 1568 产品 📁 LED驱动器 1 产品 📁 逻辑IC 305 产品 📁 存储IC 875 产品 📁 微控制器 18688 产品 📁 微处理器 4 产品 📁 电机驱动器 1 产品 📁 其他 1 产品 📁 Sensor and Detector Interfaces 1 产品 📁 专用IC 15 产品 📁 视频IC 13 产品

产品（32725)

74HC245D - Octal 3-State Bus Transceiver | Logic IC
74HC245D

74HC245D - Octal 3-State Bus Transceiver | Logic IC

The Toshiba 74HC245D is an octal, non-inverting bus transceiver with 3-state outputs, supplied in a 20-pin SOIC package. It provides eight parallel data channels for asynchronous two-way bus communication, with transmit direction selected by DIR and output enable controlled by an active-low OE input. Its 1-element, 8-bit-per-element organization supports compact bidirectional bus buffering where controlled high-impedance operation is required. A bus transceiver is a bidirectional interface IC that connects two logic buses, allows data to move in a selected direction, and places its outputs into a high-impedance state when disabled. The 74HC family belongs to high-speed CMOS logic and combines low power dissipation with performance comparable to LSTTL, making it useful in digital systems, memory interfaces, peripheral buses, and embedded control equipment. The verified product description identifies the device as an octal bus transceiver with three-state outputs. The DIR input determines the direction of data flow between the A and B buses, while the active-low output-enable input provides bus isolation. Because the outputs can be disabled, multiple drivers can share a bus when only one device is actively enabled, provided the system obeys the relevant electrical and timing constraints. The 74HC245D is manufactured using silicon-gate C2MOS technology and is specified as a high-speed CMOS logic device. Its transceiver architecture is non-inverting, so the data presented on one bus is transferred without intentional logic inversion when the corresponding direction is selected. The package is a 20-SOIC surface-mount package, matching the distributor listing for Toshiba Semiconductor and Storage. Typical applications include bidirectional data buses, microcontroller peripheral interfaces, memory-bus isolation, industrial control systems, and communication equipment. When designing a PCB, preserve the manufacturer pin assignment, provide adequate supply decoupling, and route high-speed bus traces with controlled impedance where required. Confirm enable polarity and direction timing before connecting external circuitry. This product page combines the verified manufacturer and distributor descriptions with package, application, and sourcing context. Electrical limits such as supply voltage, propagation delay, output current, and operating temperature were not included in the supplied source data and are therefore not inferred here.

USD $0.10 有现货
74HC2G17GW - Dual Non-Inverting Schmitt Trigger, 6-TSSOP | Nexperia
74HC2G17GW

74HC2G17GW - Dual Non-Inverting Schmitt Trigger, 6-TSSOP | Nexperia

The Nexperia 74HC2G17GW is a high-speed Si-gate CMOS dual non-inverting Schmitt-trigger buffer housed in a 6-pin TSSOP (SOT363 / SC-88) package. Each of the two channels accepts slowly changing input signals and converts them into sharply defined, jitter-free output signals, with a typical propagation delay of around 10 ns at 5 V VCC. The device operates from a 2.0 V to 6.0 V supply, supports ±5.2 mA output drive capability, and tolerates input signals up to VCC plus 0.5 V thanks to integrated input clamp diodes. A Schmitt trigger is a comparator-style input stage with two distinct switching thresholds - a higher threshold (VT+) for the rising edge and a lower threshold (VT-) for the falling edge. The hysteresis between these thresholds (typically 1.0 V at 5 V VCC for the 74HC2G17) rejects noise, ringing, and slow edges, producing clean digital transitions where a standard CMOS gate would oscillate. Within the broader taxonomy, this device is a logic buffer - a sub-category of interface ICs that sits between drivers and receivers, all of which fall under the umbrella of standard logic ICs and ultimately digital semiconductors. Key features include CMOS Schmitt-trigger inputs with input hysteresis, push-pull complementary outputs capable of sourcing and sinking ±5.2 mA, a maximum quiescent current in the microamp range, and ESD protection on all inputs. Inputs include clamp diodes that enable the use of current-limiting series resistors when interfacing to voltages above VCC, simplifying mixed-voltage designs. The device is specified over the -40 °C to +125 °C automotive/industrial temperature range. The 74HC2G17GW uses a high-speed CMOS Si-gate process that delivers TTL-compatible logic levels on the HC version and true TTL levels on the HCT variant (74HCT2G17GW). The push-pull output stage eliminates the need for external pull-up resistors and avoids the static power dissipation of open-drain alternatives. With two independent buffers in a 6-pin package, the part is a compact building block for signal conditioning, line receivers, and oscillator circuits. Typical applications include debouncing mechanical switches and push-buttons, conditioning slow analog signals before they reach a microcontroller, square-wave relaxation oscillators using an RC network, and rising-edge/pulse shaping in industrial control and automotive body electronics. The wide supply range and TTL-compatible thresholds make it a flexible interface between legacy 5 V logic and modern 3.3 V microcontrollers. When designing with this device, place a 0.1 µF decoupling capacitor as close as possible to the VCC pin and ensure that input rise/fall times remain slow enough that the Schmitt hysteresis is meaningfully larger than the input noise. Inputs that exceed VCC by more than one diode drop (~0.7 V) must be current-limited to within the absolute maximum rating. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for footprint-compatible parts and selection trade-offs.

USD $0.15 有现货
74HC4040BQX - 12-Stage Binary Ripple Counter | Nexperia
74HC4040BQX

74HC4040BQX - 12-Stage Binary Ripple Counter | Nexperia

The Nexperia 74HC4040BQX is a 12-stage binary ripple counter IC housed in a 16-pin DHVQFN (SOT763) leadless package measuring 2.5x3.5 mm. It is part of the high-speed Si-gate CMOS 74HC logic family and is pin-compatible with the legacy HEF4040B series, conforming to JEDEC standard no. 7A. The device advances its count on the HIGH-to-LOW transition of the clock input (CP) and provides twelve parallel buffered outputs (Q0 through Q11) for direct binary decoding. A binary counter, also called a ripple counter or divide-by-N counter, is a sequential logic circuit formed by cascading toggle flip-flops. Each stage divides the previous stage's frequency by two, producing output frequencies of fCLK/2, fCLK/4, ... fCLK/4096 at Q0..Q11. Ripple counters sit within the broader hierarchy of digital logic -> sequential logic -> counters -> frequency dividers -> clock-generation circuits, and remain widely used for low-cost timing, event-counting and watchdog applications where synchronous operation is not required. Key features of the 74HC4040BQX include an asynchronous master reset (MR) input that asynchronously clears all twelve stages and forces all outputs LOW regardless of CP state, wide operating voltage range of 2.0 V to 6.0 V, typical propagation delay of a few nanoseconds per stage, and low quiescent current. The 74HC variant accepts standard CMOS input levels while the pin-compatible 74HCT4040 variant supports TTL-level inputs for mixed-logic interfaces. Architecturally, each counter stage is a static toggle flip-flop that ripples carry from the previous stage's Q output to the next stage's clock input. This asynchronous topology limits the maximum usable clock frequency for long count chains because the cumulative delay adds as the count propagates, but for divide-by-4096 applications at modest frequencies the device is more than adequate. Typical applications include frequency division and clock generation, event/timeout counters, watchdog timers, binary address scanning in LED or relay driver chains, and waveform synthesis. Designers also use the 74HC4040 family to derive sub-system timing from a master oscillator or microcontroller clock. A key design consideration with ripple counters is the asynchronous nature of the carry - outputs do not change simultaneously and glitches may be present on intermediate outputs during transitions. For designs requiring glitch-free synchronous division, a synchronous counter such as the 74HC161 family is preferred. The MR reset is asynchronous and must be debounced in noisy environments. This page synthesizes distributor pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet alone, providing engineering context that complements the official Nexperia product family documentation.

USD $0.22 有现货
74HC4052D - Dual 4:1 Analog Mux/Demux, 16-SOIC | Nexperia
74HC4052D

74HC4052D - Dual 4:1 Analog Mux/Demux, 16-SOIC | Nexperia

The Nexperia 74HC4052D is a dual single-pole quad-throw (2 x SP4T) analog switch suitable for analog or digital 4:1 multiplexer/demultiplexer applications, housed in a 16-pin SOIC (SOT109-1) package. Key specifications include a low ON resistance of approximately 150 ohm, an operating supply voltage range of 2 V to 10 V for the VCC rail, and a wide analog signal swing from VEE to VCC (up to 10 V peak-to-peak). The device includes two independent 4-channel switches with a common digital select interface, supporting both multiplexing and demultiplexing operations in a single package. A 74HC-series analog multiplexer is a CMOS logic device that routes one of several analog input signals to a common output line, or vice versa. The 74HC4052 is part of the 4000-series analog switch family, hierarchically classified as an analog switch -> multiplexer/demultiplexer -> interface IC -> integrated circuit. These devices serve as fundamental building blocks in mixed-signal systems, enabling microcontrollers with limited I/O to sample multiple analog channels through a single ADC input, or to drive multiple loads from a single DAC output. The 74HC prefix indicates high-speed CMOS logic with TTL-compatible input thresholds, while the 4052 designation identifies the dual 4:1 channel configuration. Key differentiating features include very low power consumption (CMOS quiescent current typically in the nanoampere range), built-in ESD protection per HBM (Human-Body Model) standards, and break-before-make switching that prevents momentary shorting between adjacent channels during transitions. The 16-SOIC package provides a standardized industrial footprint with a typical thermal resistance of approximately 75 C/W and supports surface-mount reflow soldering. The part is qualified to operate over the automotive temperature grade of -40 C to +125 C. The 74HC4052D utilizes a transmission-gate architecture built from parallel NMOS and PMOS transistors, achieving near-constant ON resistance across the analog signal range and minimal distortion for audio-frequency signals. The digital control inputs (A, B, and an active-low enable) are TTL-compatible at 5 V VCC, allowing direct connection to microcontrollers and standard logic families without level shifters. The wide VEE to VCC signal path allows the device to handle bipolar analog signals when VEE is biased below ground, a critical feature for instrumentation and audio applications. Typical applications include analog signal routing in data acquisition systems, audio source selection in consumer electronics, sensor multiplexing in IoT devices, video signal switching, and industrial process control. The combination of low ON resistance, low crosstalk, and wide bandwidth (typically 100 MHz at -3 dB) makes the part suitable for both DC precision signals and high-frequency analog routing. When designing with the 74HC4052D, observe the absolute maximum ratings: VCC must never exceed 10 V (or per datasheet VCC - VEE must remain within the absolute maximum differential). Place 100 nF decoupling capacitors as close as possible to the VCC and VEE pins to suppress digital switching noise from coupling into the analog signal path. Add 10 kohm pull-up resistors on the enable pin if hard-wired always-on operation is desired. This page synthesizes distributor pricing, cross-brand drop-in alternatives, and PCB layout guidance not found in the manufacturer datasheet, helping procurement and design engineers select and source the 74HC4052D with confidence.

USD $0.16 有现货
74HC7014D - Hex Non-Inverting Precision Schmitt-Trigger | Nexperia
74HC7014D

74HC7014D - Hex Non-Inverting Precision Schmitt-Trigger | Nexperia

The Nexperia (formerly NXP/Philips) 74HC7014D is a hex non-inverting buffer with precision Schmitt-trigger inputs, specified in compliance with JEDEC standard no. 7A and housed in a 14-pin SO (SOT108) package. Each of the six channels is a 1-bit buffer element with push-pull output drive, providing standard CMOS output capability across the 3 V to 6 V operating voltage range. A Schmitt trigger is a comparator-based input stage that uses two distinct threshold voltages—one for rising edges (V_T+) and one for falling edges (V_T−)—producing a hysteresis band that prevents oscillation on slow or noisy input transitions. In the 74HC7014, these trigger levels are precisely defined at 0.55 × V_CC (V_T−) and 0.65 × V_CC (V_T+), yielding a tight 10% hysteresis window centred on V_CC/2. This precision distinguishes the 74HC7014 from general-purpose 74HC inverters (74HC04) and gates, whose thresholds vary more widely with V_CC and temperature. Key features of the 74HC7014D include high-speed Si-gate CMOS construction, low power dissipation typical of 74HC family logic, full push-pull totem-pole outputs capable of sourcing and sinking symmetric load current, and the JEDEC 7A-specified DC characteristics that guarantee interoperability with other HC-family devices. The device is pin-compatible with the 74HC04 hex inverter family footprint (14-SO/SOIC-14) but offers non-inverting transfer function with defined hysteresis. Typical applications include signal conditioning for slowly-rising sensor or mechanical-switch inputs, line receivers in noisy industrial environments, oscillator circuits (the Schmitt trigger hysteresis is the core element of relaxation oscillators), debouncing of mechanical switch contacts, and waveform shapers for clock-recovery or threshold-detection circuits. Because the trigger band tracks V_CC proportionally, the 74HC7014 also functions well as a voltage-level detector when V_CC is used as the reference. When designing with this device, observe standard CMOS handling practices (ESD protection) and ensure output loading stays within the standard HC output capability (typically ±4 mA at 6 V). For automotive or extended-temperature applications the Q100/J version is available in the same SO-14 package, providing pin-compatible migration without PCB changes.

USD $0.36 有现货
74HCT154BQ - 4-to-16 Line Decoder/Demultiplexer DHVQFN-24 | Nexperia
74HCT154BQ

74HCT154BQ - 4-to-16 Line Decoder/Demultiplexer DHVQFN-24 | Nexperia

The Nexperia (formerly NXP Semiconductors) 74HCT154BQ is a 4-to-16 line decoder/demultiplexer fabricated in high-speed Si-gate CMOS technology, packaged in a 24-pin DHVQFN (SOT815-1, 5.5 mm x 3.5 mm) surface-mount package. It accepts four active-HIGH binary weighted address inputs (A0 to A3) and drives sixteen mutually exclusive active-LOW outputs (Y0 to Y15), making it well suited to memory chip-select decoding, address demultiplexing, and discrete LED/relay driver expansion. The device is specified per JEDEC standard no. 7A and is pin-compatible with Low-power Schottky TTL (LSTTL). Background knowledge: A decoder/demultiplexer is a combinational logic device that converts a small binary address into one of many mutually exclusive outputs. It belongs to the broader category of digital logic ICs, and within that category to the encoder/decoder/multiplexer/demultiplexer sub-family. In a typical digital system hierarchy, decoders sit between the processor/control logic and the peripheral devices they enable, providing one-hot selection signals such as memory chip-select, peripheral enables, or display-row selects. The 4-to-16 decoder is one of the most commonly used building blocks for memory and I/O expansion on legacy buses. Key features of the 74HCT154BQ include two active-LOW enable inputs (E1 and E2) that can be used together as a strobe to eliminate normal address-decoding glitches on the outputs, a wide 4.5 V to 5.5 V supply range (HCT logic level, TTL-compatible inputs), CMOS output drive capability, and standardized input hysteresis for improved noise immunity in industrial environments. The two enable gates can also be cascaded to form a 5-to-32 decoder using two 74HCT154 devices, an important pattern for memory expansion beyond 16 devices. Typical applications include memory chip-select decoding for systems with up to 16 memory or peripheral devices, address demultiplexing for legacy microprocessor address buses (such as 8085, Z80, 6800), LED matrix row/column driving, relay and solenoid driver expansion, and general-purpose one-of-N selection in industrial control logic. The enable-strobe feature is particularly valuable when the device feeds asynchronous logic that would otherwise propagate decoding glitches. When designing with this part, pay attention to the active-LOW output polarity (Y outputs sink current when selected) and unused enable pins must be tied to their active state. The DHVQFN-24 package provides a low thermal resistance path and requires thermal vias under the exposed pad for reliable operation; ensure the pad is soldered to a sufficient copper area on the PCB. All inputs include clamp diodes so input voltages should be constrained within the supply range.

USD $0.43 有现货
74HCT1G04GW - Single Inverter Gate, 5-TSSOP | Nexperia
74HCT1G04GW

74HCT1G04GW - Single Inverter Gate, 5-TSSOP | Nexperia

The Nexperia 74HCT1G04GW is a single high-speed Si-gate CMOS inverter housed in a 5-pin TSSOP (SOT353/UMT5) surface-mount package. Operating from a 4.5 V to 5.5 V supply, the device delivers TTL-compatible input switching thresholds while consuming CMOS-level quiescent current, making it ideal for level translation between 5 V TTL logic and 3.3 V CMOS rails in mixed-voltage systems. What is a single-gate logic IC? A single-gate logic IC is a minimal-footprint logic function packaged in a small-outline surface-mount package (typically 5 to 6 pins). It belongs to the logic IC hierarchy: inverter -> gate -> combinational logic -> standard logic family. Single-gate devices occupy a single logic function on one die, enabling designers to place a single inverter, buffer, OR, AND, or Schmitt-trigger function exactly where it is needed on a board without paying the area or cost of a quad-gate or hex-gate package. Compared with discrete BJT/MOSFET inverter circuits, single-gate CMOS ICs offer matched propagation delays, balanced rise/fall times, ESD-rated inputs, and predictable output impedance across the full operating temperature range. Key features of the 74HCT1G04 include a wide supply voltage range, symmetrical output impedance, ESD protection on every input, balanced propagation delays, and very low power dissipation. Inputs include clamp diodes that allow current-limiting resistors to interface inputs to voltages exceeding VCC, simplifying mixed-voltage designs without external protection. Architecturally, the 74HCT1G04 uses an HCT sub-family CMOS process: the input stage accepts TTL logic levels (VIL <= 0.8 V, VIH >= 2.0 V) while the output stage swings rail-to-rail CMOS levels. This makes the HCT variant the bridge between legacy 5 V TTL peripherals and modern CMOS controllers. The standard output current is half that of the larger 74HCT04 hex inverter, but for a single logic inversion this is rarely a constraint. Typical applications include signal inversion in microcontroller I/O lines, bus signal conditioning, level translation between 5 V and 3.3 V logic domains, reset-signal inversion, and clock-signal polarity reversal. Designers also use it to debounce mechanical switches when combined with an RC network. The 5-pin TSSOP footprint keeps the inverter within a few square millimeters of board area, ideal for high-density PCB layouts and signal-integrity sensitive traces. When designing with this part, place a 0.1 uF decoupling capacitor as close as possible to the VCC pin, keep the input trace short to minimize capacitive loading, and verify that the driving source can supply at least 1 mA through the input clamp diode if input voltages can exceed VCC during hot-plug or fault conditions. This page consolidates distributor pricing for the 74HCT1G04GW, 5-TSSOP drop-in alternatives from Nexperia and TI, and engineering design notes that complement the manufacturer datasheet.

USD $0.12 有现货
74HCT1G04GW-Q100H - Single Inverter, 5-TSSOP, AEC-Q100 | Nexperia
74HCT1G04GW-Q100H

74HCT1G04GW-Q100H - Single Inverter, 5-TSSOP, AEC-Q100 | Nexperia

The Nexperia 74HCT1G04GW-Q100H is a single inverter gate in the 74HCT logic family, qualified to AEC-Q100 Grade 1 for automotive applications, housed in a 5-pin TSSOP (SOT353-1 / UMT5) package. The "HCT" suffix indicates high-speed CMOS with TTL-compatible input thresholds, allowing direct interfacing with TTL-level signals while preserving CMOS-like output levels, noise margins, and quiescent current. Operating across a 2.0 V to 5.5 V VCC range with typical propagation delay around 6 ns at 4.5 V, it suits clock-conditioning, reset inversion, and signal-level translation in mixed-logic boards. A single inverter, also called a NOT gate, is the most fundamental combinational building block in digital logic. It flips the logical state at its output - a logic-low at the input yields a logic-high at the output, and vice versa. Inverter gates form the foundation for NAND, NOR, XOR, and oscillator circuits when combined with other primitives. The 74HCT1G series in particular integrates one gate into an ultra-small SOT353 / SC-88 footprint, providing complete logic functions at minimal board area. The -Q100 suffix denotes full AEC-Q100 Grade 1 qualification, suiting under-hood automotive environments with extended thermal stress. Key features of this part include ±2 mA balanced output drive at 4.5 V, input clamp diodes that allow current-limiting resistors to interface inputs to voltages exceeding VCC, very low quiescent supply current, and stable operation across -40 °C to +125 °C. Inputs tolerate 5 V even when VCC is unpowered, simplifying mixed-voltage designs. CMOS output stages produce rail-to-rail swings, eliminating the V_OL/V_OH gap that plagues TTL. The internal architecture uses a single-stage CMOS inverter cell with a buffered output, giving consistent drive strength in both directions. Compared with discrete transistor inverters, the integrated 74HCT1G04 delivers matched rise/fall edges, defined propagation delay, and immunity to power-supply variation. The Schmitt-trigger-free design requires clean edges - place a series resistor at the input when driving from long PCB traces to avoid double-triggering. Typical applications include automotive body controllers, sensor-signal inversion in BCM/ECU modules, level translation between 3.3 V microcontrollers and 5 V peripherals, reset-signal conditioning, and clock inversion in portable and industrial devices. The Q-100 qualification also opens infotainment, ADAS sensor pre-processing, and lighting-control modules. Designers should treat the 5-TSSOP land pattern as the layout contract; pin 1 dot-marker is at top-left. Bypass VCC with a 100 nF ceramic placed within 5 mm of the supply pin. The input clamp diodes allow direct connection to voltages above VCC through a current-limiting resistor (typically 10 kΩ). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

USD $0.02 有现货
74LS244N - Octal Buffer/Line Driver 3-State 20-PDIP | TI
74LS244N

74LS244N - Octal Buffer/Line Driver 3-State 20-PDIP | TI

The Texas Instruments 74LS244N is an octal buffer and line driver with 3-state outputs in a 20-pin PDIP package, organized as two non-inverting 4-bit elements with independent active-low output-enable controls. It is a Low-power Schottky (LS) TTL device operating from a 4.75 V to 5.25 V supply with TTL-compatible inputs that include PNP inputs to reduce DC loading on upstream drivers. The device sinks up to 24 mA per output in the LOW state and sources up to -15 mA in the HIGH state, providing strong drive for heavily loaded buses. An octal buffer/line driver is a type of bus-interface logic IC used to isolate, boost, and directionally drive parallel data, address, or control signals between a controller and a bus. The 74LS244 is the de-facto industry standard 'bus driver' in the 74LS logic family and is widely second-sourced. It is commonly employed as a memory-address driver, clock driver, or bus-oriented transmitter/receiver, sitting one tier below the system CPU in the digital logic hierarchy and one tier above discrete bus traces. Key features of the 74LS244N include symmetric active-low output-enable (1G, 2G) inputs that allow grouping into two 4-bit banks, 3-state outputs that present a high-impedance state when disabled, input hysteresis for improved noise margin, and ESD protection that exceeds typical 74LS ratings. The 'N' suffix denotes the through-hole 20-pin PDIP package, while 'M' would denote SOIC and 'NS' denotes SOP. Architecturally, the 74LS244N uses bipolar Low-power Schottky technology with a Schottky-clamped transistor design that delivers low propagation delay (typically around 10-12 ns) at modest power consumption compared to standard 74-series TTL. The two independent enable lines let designers disable half the bus while the other half remains active, which is useful in mixed-voltage or partial-power-down designs. Typical applications include memory-address bus buffering in 8-bit microcomputer and retrocomputing designs (Z80, 6502, 8080), clock-driver fan-out, peripheral-interface buffering, and bus isolation in educational or industrial PLC systems. It is also used to drive long PCB traces or backplane lines where the source drive of a typical microcontroller output would be insufficient. When designing with this part, ensure that both 1G and 2G are tied LOW during normal operation to enable outputs, and that the high-impedance state is used to isolate two devices sharing a bus. Decoupling VCC with a 0.1 uF ceramic capacitor placed close to the supply pin is recommended to suppress switching transients. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes that are not found in the bare manufacturer datasheet, helping engineers compare second-source options and design a robust bus-buffer stage.

USD $0.62 有现货
74LV1T34GV-Q100H - 1.65-5.5V Level Translating Buffer SC-74A | Nexperia
74LV1T34GV-Q100H

74LV1T34GV-Q100H - 1.65-5.5V Level Translating Buffer SC-74A | Nexperia

The Nexperia 74LV1T34GV-Q100H is a single, non-inverting, level-translating CMOS buffer in a 5-pin SC-74A (SOT-753) surface-mount package. It supports an input range that allows 1.8 V CMOS logic signals to drive a 3.3 V rail (level-up translation), while 5 V-tolerant inputs enable 3.3 V-to-2.5 V level-down translation at VCC = 2.5 V. The output level references the supply voltage and supports 1.8 V, 2.5 V, 3.3 V, and 5 V rails from a single device. A level-translating buffer is a logic buffer that accepts input voltages from a wide range of logic families and re-references its output to the local supply. This category sits inside the broader class of voltage level shifters, which in turn belong to logic ICs and interface ICs used in mixed-voltage digital systems. By collapsing 1.2 V, 1.8 V, 2.5 V, 3.3 V, and 5 V interfaces onto a single part, these devices reduce BOM count in multi-rail SoC designs. Key features include CMOS low-power operation, push-pull drive, ±8 mA output drive capability, and a wide VCC operating range of 1.6 V to 5.5 V. Inputs accept logic levels above VCC up to 5.5 V regardless of the supply, and the device is qualified to AEC-Q100 Grade 1 for automotive applications, supporting operation from -40 C to +125 C. Internally, the 74LV1T34GV-Q100H uses a single NMOS/PMOS stage with low-threshold input transistors that recognise a logic HIGH far below the supply rail. The output stage is a symmetric push-pull CMOS driver that swings rail-to-rail, giving balanced edge rates for both rising and falling transitions and avoiding the DC current path that open-drain translators require. Typical applications include GPIO voltage translation between a 1.8 V application processor and 3.3 V peripherals, I2C/SPI/UART level shifting between microcontrollers and 5 V sensors, signal conditioning for SD cards and SIM interfaces, automotive body controllers and infotainment links, and any point-to-point signal where board rework to a multi-channel translator would be unnecessary. When designing with this part, confirm that the input HIGH threshold stays below the driver's VOH at the chosen VCC and keep the trace under a few centimetres because this single-channel buffer does not include series damping. Add a 100 nF decoupling cap next to VCC and avoid pulling the input above 5.5 V even though it is 5 V-tolerant. This page synthesises distributor stock, drop-in same-package alternatives, and practical design notes not found in the Nexperia datasheet, providing a single-engineer reference for level-shifting buffer selection.

USD $0.15 有现货
74LV4053D,118 - Triple SPDT Analog Switch, 2:1 MUX, SO-16 | Nexperia
74LV4053D,118

74LV4053D,118 - Triple SPDT Analog Switch, 2:1 MUX, SO-16 | Nexperia

The Nexperia 74LV4053D,118 is a triple single-pole double-throw (SPDT) analog switch implemented in low-voltage CMOS logic, housed in a 16-pin small-outline (SO-16 / SOT109) surface-mount package. The IC operates from a single 1.0 V to 6.0 V supply rail, supports 2:1 multiplexing/demultiplexing of analog or digital signals, and provides a typical on-resistance of 105 ohm (225 ohm maximum) per channel. Each switch section features an independent digital select input (Sn), two bidirectional I/O pins (nY0, nY1), and a common bidirectional I/O pin (nZ), with all channels sharing a single enable input. An analog switch IC (also called a CMOS transmission gate or bilateral switch) is a solid-state device that uses MOSFET pairs to route analog or digital signals between multiple nodes without mechanical contacts. Analog switches sit at the boundary between the analog signal chain and the digital control logic, performing the same role that mechanical relays performed historically, but with far higher speed, lower power, no contact bounce, and essentially infinite mechanical life. The 74LV4053 belongs to the broader category of multiplexer/demultiplexer (MUX/DEMUX) ICs, which themselves fall under the interface ICs hierarchy within the integrated-circuit taxonomy. Key differentiating features include very low quiescent current (a few microamps at 25 °C), fast switching with typical turn-on (tON) of 190 ns and turn-off (tOFF) of 125 ns at 3 V, 5 ohm on-resistance matching between channels (Delta-RON), and 50 dB off-isolation (VISO) at typical audio frequencies. The device is pin- and function-compatible with the higher-voltage 74HC4053 and 74HCT4053 families, allowing direct substitution in existing footprints when a lower-voltage rail is acceptable. Integrated logic-level translation also makes it suitable for interfacing 5 V controllers with 1.8 V or 3.3 V peripherals. Architecturally, the 74LV4053D uses N-channel and P-channel MOSFET pairs in a transmission-gate topology for each of the three switches; the CMOS process delivers bidirectional signal handling from rail to rail, low charge injection, and high input impedance for both analog and digital signals. Because all switches share a common substrate, designers should observe standard ESD handling precautions and avoid signal voltages that exceed VDD7. Typical applications include audio signal routing in portable consumer devices, multiplexing sensor outputs to a microcontroller ADC, video or composite signal switching, communication line routing, and general-purpose signal-path selection in industrial and automotive subsystems. The wide 1.0 V to 6.0 V supply range makes the part equally comfortable in coin-cell powered IoT nodes and 5 V legacy systems. When designing with this device, ensure that the analog signal swing remains within the VDD and GND rails to prevent latch-up of the internal transmission-gate MOSFETs. Add 100 nF ceramic bypass capacitors adjacent to VDD and GND, and route digital select lines away from sensitive analog traces to preserve the 50 dB off-isolation figure. This page consolidates distributor pricing, verified drop-in alternatives, and practical design notes that are not assembled in the manufacturer short datasheet, providing engineers with a single source for procurement and design decisions.

USD $0.28 有现货
74LVC1G00GW - Single 2-Input NAND Gate, 1.65V-5.5V | Nexperia
74LVC1G00GW

74LVC1G00GW - Single 2-Input NAND Gate, 1.65V-5.5V | Nexperia

The Nexperia 74LVC1G00GW is a single 2-input NAND gate fabricated with sub-micron Si-gate CMOS technology, providing high-performance low-power low-voltage logic in a 5-pin TSSOP (SOT-353 / UMT5) surface-mount package. The part operates from a wide supply voltage range of 1.65 V to 5.5 V, delivers ±24 mA output drive at VCC = 3.0 V, and supports a propagation delay of approximately 10.5 ns at nominal conditions, making it well suited to modern mixed-voltage systems where 3.3 V and 5 V domains coexist on the same board. An LVC (Low-Voltage CMOS) gate is a sub-family of advanced CMOS logic optimized for operation below 5 V while remaining tolerant of 5 V input signals. Within the broader logic hierarchy, the 74LVC1G00 sits inside the single-gate 74LVC1G family, which in turn belongs to Nexperia's 74LVC logic IC portfolio for power-efficient portable, industrial, and computing designs. Unlike legacy HC/T families, LVC combines low static power consumption with high noise immunity and JEDEC-compliant interface thresholds. Key features include Schmitt-trigger inputs that tolerate slow or noisy edges, ±24 mA balanced output drive (VCC = 3.0 V) for direct LED or bus loading, latch-up performance exceeding 250 mA per JEDEC JESD78, CMOS low static power consumption, and IOFF partial-power-down support that prevents back-feed currents when the device is unpowered but signal lines remain live. Inputs accept 3.3 V or 5 V logic levels, allowing the part to act as a down-translator in mixed-voltage systems without external level-shifters. Typical applications span portable and battery-powered electronics, mobile phones and wearables, level shifting between 5 V microcontrollers and 3.3 V peripherals, general-purpose glue logic on FPGA and ASIC boards, and interface buffering in industrial control and white-goods modules. The compact 5-pin TSSOP footprint enables placement near connectors and signal sources for short, clean traces. When designing with this device, always observe the absolute-maximum VCC of 6.5 V and derate output current above VCC = 4.5 V. Place a 0.1 µF decoupling capacitor as close as possible to VCC pin 5, and unused inputs must be tied to VCC or GND to prevent floating-input quiescent current. The TSSOP-5 footprint is mechanically compatible with Nexperia's entire 74LVC1Gxx single-gate family, simplifying BOM consolidation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer product page alone, giving the engineer a single reference for sourcing and second-sourcing decisions.

USD $0.04 有现货
74LVC1G123DC - Single Retriggerable Monostable Multivibrator | Nexperia
74LVC1G123DC

74LVC1G123DC - Single Retriggerable Monostable Multivibrator | Nexperia

The Nexperia 74LVC1G123DC is a single retriggerable monostable multivibrator with Schmitt-trigger inputs housed in an 8-pin VSSOP (DC) package, operating from 1.65 V to 5.5 V VCC with a typical propagation delay of 5.3 ns at 5 V VCC and CMOS-level totem-pole output drive. The device programs its output pulse width via an external resistor (REXT) and capacitor (CEXT), and supports retriggering through either the gated active-LOW A input or the active-HIGH B input. An integrated Ioff circuitry disables the outputs during partial power-down, preventing damaging backflow current in mixed-voltage buses. What is a monostable multivibrator? A monostable multivibrator (commonly called a one-shot) is a sequential logic element with one stable state and one temporary state. Upon receiving a valid trigger edge, the circuit switches to the temporary state for a programmed interval, then returns to the stable state. The 74LVC1G123 belongs to the LVC (Low-Voltage CMOS) logic family within the broader CMOS logic IC hierarchy, occupying the specialty-logic sub-category alongside multivibrators, Schmitt triggers, and buffers. Key features include three pulse-width control methods: external R-C programming, retriggering via the gated active-LOW A or active-HIGH B input, and direct reset via the CLR input. Schmitt-trigger action on both trigger inputs (A and B) makes the device highly immune to slow or noisy edges - typical hysteresis of approximately 0.8 V at 3.3 V VCC rejects input noise of several hundred millivolts. The wide 1.65 V to 5.5 V supply range enables direct interfacing between 1.8 V, 2.5 V, 3.3 V, and 5 V logic domains without external level shifters. The architecture combines an edge-triggered control gate, a precision pulse-width timing core, and a totem-pole CMOS output stage capable of sourcing/sinking up to 32 mA at 3.3 V. Ioff partial-power-down support means the device can be inserted into live buses safely when VCC is removed - a critical feature for hot-swap or multi-rail designs. The Schmitt hysteresis on both trigger inputs delivers reliable operation in electrically noisy industrial environments where standard CMOS gates would double-trigger. Typical applications include pulse generation in industrial control, watchdog timer circuits, debouncing mechanical switches and rotary encoders, missing-pulse detection in motor-control feedback loops, and reset pulse shaping in microcontroller-based systems. The 5 V tolerance on outputs (when VCC = 3.3 V) also makes it useful for legacy 5 V peripheral interfacing in mixed-voltage systems. When designing with the 74LVC1G123DC, select the external REXT and CEXT using the datasheet pulse-width formula tw = REXT × CEXT × ln(2) ≈ 0.69 × REXT × CEXT and verify timing across process, voltage, and temperature corners. Place CEXT as close as possible to the device pins to minimize parasitic capacitance that would otherwise skew the timing accuracy. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $0.26 有现货
74LVC1G27GW - Single 3-Input NOR Gate, 1.65-5.5V | Nexperia
74LVC1G27GW

74LVC1G27GW - Single 3-Input NOR Gate, 1.65-5.5V | Nexperia

The Nexperia 74LVC1G27GW is a single 3-input NOR gate IC in the 74LVC (Low-Voltage CMOS) logic family, packaged in a 6-pin TSSOP (SOT-363/SC-88). It provides one 3-input NOR function and accepts a wide supply voltage range from 1.65 V to 5.5 V, supporting both 3.3 V and 5 V mixed-voltage applications. Inputs can be driven from either 3.3 V or 5 V devices, allowing its use as a translator between logic domains without external level shifters. A logic gate is a fundamental building block of digital electronics that performs a Boolean operation on one or more binary inputs to produce a single binary output. The 3-input NOR gate outputs logic HIGH only when ALL three inputs are LOW; if any input is HIGH, the output is LOW. As part of the NOR gate hierarchy, this device is a member of the broader logic IC family, which also includes AND, OR, NAND, XOR, and inverter gates. NOR gates are functionally complete and can be combined to construct any other logic function, making them especially valuable in glue logic and minimal-component designs. Key features of the 74LVC1G27GW include 24 mA output drive capability at VCC = 3.0 V, CMOS low power consumption, and Schmitt-trigger action at all inputs for tolerance to slow rise/fall times. ESD protection meets HBM JESD22-A114F (>2000 V), MM JESD22-A115-A (>200 V), and CDM JESD22-C101-C (>1000 V). It complies with JEDEC standards JESD8-7, JESD8-5, and JESD8B/JESD36, and supports IOFF partial power-down operation to prevent backflow current when one side of the device is powered down. Internally, the 74LVC1G27GW uses CMOS technology with sub-micron geometries to deliver rail-to-rail output swings at low quiescent current. The Schmitt-trigger input hysteresis improves noise immunity in noisy environments and makes the device tolerant of slowly changing input signals. With 50 ns typical propagation delay at 3.3 V and a tiny 6-pin footprint, the device is optimized for high-density PCB designs where board area and signal integrity are critical. Typical applications include voltage level translation between 3.3 V and 5 V buses, glue logic in microcontroller interfaces, signal inversion and combination in industrial controls, and handheld or battery-powered portable equipment requiring low-power operation. The wide supply range enables direct connection to single-cell Li-ion batteries (3.0 V to 4.2 V) or to regulated 1.8 V rails in modern SoCs. When designing with this device, ensure that VCC is properly decoupled with a 100 nF ceramic capacitor placed within 5 mm of the VCC pin. Unused inputs should be tied to VCC or GND through a defined logic level; never leave inputs floating because the Schmitt-trigger hysteresis can cause oscillation. For mixed-voltage applications, confirm that input high-level voltage (VIH) and low-level voltage (VIL) thresholds of the driving device are compatible with the 74LVC family at your chosen VCC. This page synthesizes distributor pricing from DigiKey, Mouser, LCSC, and Octopart; same-brand and cross-brand drop-in alternatives in SOT-363/SC-88; and practical design notes not consolidated in any single manufacturer datasheet.

USD $0.13 有现货
74LVC1G27GW-Q100H - Single 3-Input NOR Gate, Automotive | Nexperia
74LVC1G27GW-Q100H

74LVC1G27GW-Q100H - Single 3-Input NOR Gate, Automotive | Nexperia

The Nexperia 74LVC1G27GW-Q100H is a single 3-input NOR gate fabricated in CMOS silicon-gate technology and qualified to the AEC-Q100 automotive standard. It operates from a 1.65 V to 5.5 V supply, supports 32 mA output drive (sink and source), and delivers a typical propagation delay of 4.5 ns at 5 V with 50 pF load, all housed in a 6-pin SOT363 (SC-88) package. The Q100 suffix and H designation confirm full automotive-grade qualification with PPAP support. A NOR gate is a fundamental digital logic gate that produces a logic-high output only when ALL of its inputs are logic-low; if any input is high, the output is forced low. The 3-input variant integrates three parallel OR inputs followed by inversion, useful for compact combinational logic, multi-input fault detection, and qualification functions. NOR gates sit within the broader logic family hierarchy as: NOR gate -> OR-derived logic -> combinational logic -> CMOS logic -> integrated circuit. Key features include wide 1.65 V to 5.5 V supply operation, 5 V tolerant inputs that allow direct interfacing with 3.3 V or 5 V devices, Schmitt-trigger input action for noise immunity with slow edges, and I_OFF circuitry that enables partial power-down by preventing damaging backflow current when the device is unpowered. Typical quiescent current is 4 uA, and the device supports output voltages from 0.95 V to VCC - 0.5 V (3.4 V at 5 V supply). The 74LVC1G27GW-Q100H uses Nexperia's LVC (Low-Voltage CMOS) technology, optimized for low power and high speed at low voltages. The Schmitt-trigger inputs provide hysteresis that prevents oscillation on slow input transitions, which is essential in industrial and automotive environments with long PCB traces. The I_OFF feature makes the part safe for hot-insert and bus-isolated applications where partial sections are powered down to save energy. Typical applications include automotive body and chassis electronics, industrial sensor signal conditioning, level translation between 3.3 V and 5 V logic domains, handheld battery-powered devices, and embedded computing boards requiring a single compact NOR gate rather than a multi-channel package. The -40 C to +125 C operating range supports under-hood and outdoor deployments. When designing with this part, observe 5 V tolerant input thresholds and derate output drive at low VCC: at 1.8 V supply the 32 mA rating drops significantly. Always check the I_OFF specification if the device sits on a live bus while locally unpowered. The SC-88 (SOT363) footprint is the same as the SC-70 family and is footprint-compatible with industry-standard 6-pin micro-logic packages. This page synthesizes distributor pricing, automotive-grade alternatives, and PCB design notes not found in the manufacturer datasheet alone.

USD $0.09 有现货
74LVC1G3157GW - 10Ω SPDT Analog Switch | Nexperia 6-TSSOP
74LVC1G3157GW

74LVC1G3157GW - 10Ω SPDT Analog Switch | Nexperia 6-TSSOP

The Nexperia 74LVC1G3157GW is a single-pole double-throw (SPDT) analog switch housed in a 6-pin TSSOP (SOT363) package, featuring 10Ω typical ON resistance and a 1.65V to 5.5V supply range. This device provides a 2:1 analog multiplexer/demultiplexer function with break-before-make switching and 32 mA switch current capability. According to the Nexperia datasheet, the part operates from 1.65V to 5.5V VCC with control inputs tolerant of 3.3V and 5V drive levels, enabling mixed-voltage signal routing in modern low-voltage systems. An analog switch (also called a bilateral switch or pass gate) is a semiconductor device that uses MOSFET transistors to route analog or digital signals between multiple paths under digital control. The 74LVC1G3157 sits in the broader hierarchy of: analog switch → multiplexer/demultiplexer → interface IC → integrated circuit → semiconductor. Single-pole double-throw switches like this are the simplest multiplexers and form the foundation of signal routing in mixed-signal systems, providing isolation between channels, level shifting between voltage domains, and dynamic signal path selection. Key features include very low ON resistance of 7.5Ω typical at VCC=2.7V, 6.5Ω typical at VCC=3.3V, and 6Ω typical at VCC=5V, with ESD protection exceeding 2000V HBM per JESD22-A114F. The device offers high noise immunity CMOS construction, TTL interface compatibility at 3.3V, and CMOS low power consumption. Latch-up performance meets JESD 78 Class I requirements, ensuring robust operation in demanding environments. The 74LVC1G3157 employs a parallel MOSFET topology where the select input (S) drives complementary gate signals to connect the common terminal (Z) to either Y0 or Y1. This architecture delivers excellent signal fidelity across the full analog input range (0V to VCC) with minimal distortion. The break-before-make switching eliminates momentary shorts between Y0 and Y1 during transitions, protecting source and downstream circuitry. Typical applications include signal routing in portable consumer devices, audio source switching in headsets, USB signal multiplexing, GPIO expansion in microcontrollers, and voltage domain translation between 1.8V, 3.3V, and 5V systems. The wide supply range and TTL-compatible inputs make this part ideal for bridging legacy 5V peripherals with modern 1.8V processors. When designing with this device, ensure VCC is well-decoupled with a 100nF ceramic capacitor placed close to the supply pin. The analog signal range is rail-to-rail (0V to VCC), but exceeding VCC on any signal pin will forward-bias the ESD protection diodes. For hot-plug applications, add series resistance to limit inrush current.

USD $0.11 有现货
74LVC1GU04GW,125 - Single Unbuffered Inverter | Nexperia | 5-TSSOP
74LVC1GU04GW125

74LVC1GU04GW,125 - Single Unbuffered Inverter | Nexperia | 5-TSSOP

The Nexperia 74LVC1GU04GW,125 is a single unbuffered inverter IC housed in a 5-pin TSSOP (SOT-353/UMT5) package, built on a Si-gate CMOS process that delivers superior performance over most advanced CMOS-compatible TTL families. The device operates across a wide 1.65 V to 5.5 V supply range and accepts input drive levels from either 3.3 V or 5 V logic, making it drop-in compatible with mixed-voltage system designs. As an unbuffered (raw inverter) topology, it provides the shortest possible propagation delay in its class while maintaining low static power consumption. An unbuffered inverter is a single-input CMOS logic function that inverts the input logic level at the output without an internal Schmitt-trigger or amplification stage. This places the unbuffered inverter in the digital-logic IC family hierarchy: inverter -> gate -> combinational logic -> logic IC -> integrated circuit -> semiconductor. Unbuffered inverters are preferred over buffered (standard) inverters in oscillator circuits, linear amplifiers, and analog signal paths because the absence of an internal gain stage preserves signal linearity and minimizes additive phase shift. The 74LVC1GU04GW,125 features a typical quiescent current of 100 µA, ±24 mA output drive capability at 3.3 V, and propagation delay of 1.7 ns typical at 3.3 V VCC with 15 pF load. The wide operating voltage window, schmitt-tolerant inputs, and 5-pin TSSOP footprint make it ideal for portable, IoT, and space-constrained PCB layouts. Nexperia's LVC family is also characterized by low-power operation, making it suitable for battery-powered applications where quiescent current directly affects runtime. The device architecture uses a single CMOS inverter cell whose output transitions follow the input directly without hysteresis. This raw-inverter topology is essential when the inverter is used as a linear amplifier or in crystal-oscillator feedback loops where the buffered variant's gain stage would distort the waveform. The 5-pin SOT-353 package provides a compact 2.0 mm x 1.25 mm x 1.1 mm outline. Typical applications include crystal oscillator modules, sine-wave to logic-level converters, level translation in mixed 3.3 V / 5 V systems, and general-purpose logic inversion in portable and IoT devices. The device is also commonly used as a small-signal amplifier in RF detector circuits and as a delay element in digital timing chains. When designing with this part, note that the input has no Schmitt-trigger hysteresis; therefore, slow or noisy edges may produce multiple output transitions. Place a small series resistor at the input (typically 100 ohm to 1 kohm) when driving from long PCB traces to control edge rate. The 5-TSSOP package has a thermal resistance of approximately 250 C/W, so output current must be limited well below 24 mA continuous in high-ambient-temperature environments. This page synthesizes Nexperia distributor pricing, real cross-brand drop-in equivalents sourced from the same 5-TSSOP footprint, and practical analog/digital design notes not found in the manufacturer datasheet.

USD $0.11 有现货
74LVC2G02DC-Q100 - Dual 2-Input NOR Gate, AEC-Q100 | Nexperia
74LVC2G02DC-Q100

74LVC2G02DC-Q100 - Dual 2-Input NOR Gate, AEC-Q100 | Nexperia

The Nexperia 74LVC2G02DC-Q100 is a dual 2-input NOR gate fabricated in CMOS logic and qualified to the AEC-Q100 automotive reliability standard, housed in an 8-pin VSSOP (SOT765, DC) package measuring approximately 2.30 mm x 2.30 mm. Each gate independently performs the Boolean NOR function Y = NOT(A OR B), and both gates share a common supply pin. The device operates across a 1.65 V to 5.5 V VCC range, with inputs tolerant of voltages up to 5.5 V regardless of VCC level, enabling direct interfacing between 3.3 V and 5 V nodes in mixed-voltage designs. A NOR gate is a fundamental CMOS logic building block that produces a HIGH output only when both of its inputs are LOW; when either input goes HIGH, the output is forced LOW. As part of the broader logic IC family (logic gate -> combinational logic -> digital IC -> semiconductor), the NOR function is functionally complete on its own, meaning any Boolean expression can be constructed from NOR gates alone - a property leveraged in classic RTL designs and modern low-density glue-logic applications. Key parametric features include a typical propagation delay of approximately 2.4 ns at 5 V VCC (per Nexperia 74LVC2G02 family datasheet), Schmitt-trigger inputs that tolerate slow or noisy edges, IOFF circuitry that disables outputs during partial-power-down to prevent backflow current, and automotive-grade reliability from -40 C to +125 C. The wide supply range supports both 1.8 V, 2.5 V, 3.3 V, and 5 V rails without level shifters. Architecturally, the device uses Nexperia's standard LVC (Low-Voltage CMOS) topology with parallel P/N-MOS pull-up/pull-down networks sized for balanced rise and fall times. The Schmitt-trigger hysteresis at each input raises the noise margin above that of conventional CMOS gates, while IOFF diodes protect downstream ICs when VCC collapses. Typical applications include automotive body and chassis ECUs, infotainment and ADAS sensor signal conditioning, 3.3 V-to-5 V level translation, control logic for motor drivers, and general-purpose glue logic in industrial PLCs. The Q100 suffix indicates AEC-Q100 qualification for automotive use cases. When laying out the part, place the VCC decoupling capacitor within 2 mm of the supply pin and avoid routing noisy switching traces near the inputs to preserve the Schmitt-trigger hysteresis. For battery-powered designs, account for the quiescent supply current draw even when logic states are static.

USD $0.15 有现货
74LVC2G125DC - Dual 3-State Buffer 1.65V-5.5V | Nexperia
74LVC2G125DC

74LVC2G125DC - Dual 3-State Buffer 1.65V-5.5V | Nexperia

The Nexperia 74LVC2G125DC is a dual non-inverting buffer/line driver with 3-state outputs, housed in an 8-pin VSSOP (SOT765) package. It operates over a wide supply voltage range of 1.65 V to 5.5 V and accepts input signals up to 5.5 V regardless of VCC, enabling seamless interfacing between 3.3 V and 5 V logic families without level shifters. A buffer IC (also called a line driver) is a digital logic component whose primary function is to isolate a signal source from its load while reproducing the input logic level at the output with no inversion. Buffers with 3-state outputs (high, low, high-impedance) allow multiple devices to share a common bus by selectively enabling or disabling the output stage. The 74LVC family belongs to the Low-Voltage CMOS logic family, characterized by low static power consumption, high noise margin, and 5 V input tolerance even when powered at lower voltages - making it ideal for mixed-voltage system designs. Key features include ±24 mA output drive capability at VCC = 3.0 V, typical propagation delay of 2.0 ns at VCC = 3.3 V, and integrated ESD protection exceeding 2000 V HBM (JESD22-A114) and 200 V MM (JESD22-A115). Each buffer has an independent active-low output enable pin (1OE, 2OE), allowing per-channel bus control. The CMOS low-power design minimizes quiescent current draw, which is critical for battery-powered and always-on applications. The 74LVC2G125DC utilizes Nexperia's advanced CMOS process with Schmitt-trigger inputs for improved noise immunity and slow-input transition tolerance. Output edges are well-controlled, and the symmetric output drive ensures balanced rise/fall times across operating conditions. Independent enable inputs support partial power gating, enabling selective deactivation of unused signal paths. Typical applications include bus isolation in mixed-voltage systems, signal buffering for memory and peripheral interfaces, level translation between 5 V and 3.3 V logic domains, fan-out expansion for clock distribution, and I/O port expansion in microcontrollers. The wide operating range makes it equally suitable for portable consumer devices and industrial control systems. When designing with this part, ensure that the 3-state enable pins are properly managed to avoid bus contention. Always deassert nOE before changing direction in bidirectional applications to prevent momentary short circuits. The VSSOP-8 package requires careful PCB layout for clean signal integrity at high data rates.

USD $0.14 有现货
74LVC4245ABQ+118 - Octal Dual-Supply Translating Transceiver | Nexperia
74LVC4245ABQ+118

74LVC4245ABQ+118 - Octal Dual-Supply Translating Transceiver | Nexperia

The Nexperia 74LVC4245ABQ+118 is an octal dual-supply translating transceiver featuring non-inverting 3-state bus-compatible outputs in both send and receive directions, housed in a 24-pin DHVQFN (5.5x3.5) package with an exposed thermal pad. The device is designed to interface between a 3 V and 5 V bus in a mixed-voltage supply environment, providing bidirectional voltage translation across eight channels with a single direction-control input (DIR) and an output-enable input (OE). A HIGH on OE forces all outputs to a high-impedance state, allowing bus isolation when required. A voltage level translator is an interface IC that allows logic signals crossing different supply domains to communicate without damage or signal integrity loss. Within the broader hierarchy, the 74LVC4245A sits inside the bus transceiver family, which is itself part of the logic IC category, under the umbrella of interface ICs and integrated circuits. The "dual supply" qualifier means the IC carries two independent VCC rails: a 5 V rail (VCC(5V)) on the B-side and a 3.3 V rail (VCC(3V)) on the A-side. This dual-rail topology is the cornerstone feature that enables transparent translation between legacy 5 V peripherals and modern 3.3 V processors, FPGAs, and ASICs. Key features include eight bidirectional channels, ±24 mA output drive on the B-side, low-power CMOS construction, and an operating temperature range from -40 °C to +125 °C. The device accepts input voltages up to 5.5 V on the 5 V side while being powered by a 3.3 V rail, and it supports 3-state outputs that isolate either bus when disabled. The exposed-pad DHVQFN-24 package provides low thermal resistance, supporting sustained heavy drive loads without derating. Technically, the 74LVC4245A uses a wide-bandwidth pass-gate architecture that avoids the direction-switching dead time typical of discrete MOSFET translation circuits. The DIR pin sets the data flow from A to B (HIGH) or B to A (LOW), and the OE pin enables or three-states the outputs. Because the device is non-inverting, the A-side logic level is mirrored directly on the B-side and vice versa, simplifying firmware design. Typical applications include 3.3 V to 5 V bidirectional bus translation in mixed-voltage microcontroller systems, expansion bus isolation between processor and peripheral cards, and legacy interface bridging in industrial control, point-of-sale, and embedded computing platforms. A key design consideration when using this part is that the DIR pin must be driven by the controller that owns the bus, and the OE pin must be toggled to prevent bus contention during direction changes. Decoupling both VCC rails with 100 nF ceramic capacitors placed as close as possible to the IC pins is critical for clean translation at high edge rates. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not aggregated in the manufacturer datasheet.

USD $0.39 有现货
74SSTUB32868 - 28-Bit to 56-Bit Registered Buffer | TI
74SSTUB32868

74SSTUB32868 - 28-Bit to 56-Bit Registered Buffer | TI

The 74SSTUB32868 is a 28-bit to 56-bit registered buffer with address-parity test, designed by Texas Instruments for DDR2 memory modules. It operates at a VCC of 1.7V to 1.9V, making it suitable for low-voltage memory interfaces. The device is available in a 176-ball NFBGA (6x15 mm) package, offering a compact solution for high-density memory modules. A registered buffer is a type of logic device that latches address and control signals to reduce the electrical loading on the memory controller, enabling higher-speed and higher-capacity memory systems. In the hierarchy of memory interface components, the registered buffer sits between the memory controller and the DRAM devices, providing signal buffering and timing alignment. This function is critical in DDR2 and DDR3 modules where signal integrity and timing margins are paramount. Key features include a 1:2 configurable registered buffer topology, which allows one input to drive two outputs, effectively doubling the fan-out for address and control signals. The device also includes address-parity test functionality, which detects parity errors on the address bus, enhancing system reliability. The 176-ball NFBGA package provides excellent thermal and electrical performance, with a compact footprint suitable for space-constrained memory module designs. From a technical perspective, the 74SSTUB32868 uses SSTL_18 I/O standards, compatible with 1.8V memory interfaces. It supports differential clock inputs (CK and CK#) for precise timing, and includes a reset function for initialization. The device is designed to meet JEDEC standards for DDR2 registered DIMMs, ensuring interoperability with standard memory modules. Its low-voltage operation reduces power consumption, making it ideal for power-sensitive applications. Typical applications include DDR2 registered DIMMs, servers, workstations, and networking equipment where high memory capacity and reliability are required. The device is also used in embedded systems that demand robust memory interfaces. Its address-parity test feature is particularly valuable in mission-critical systems where data integrity is paramount. When designing with this device, ensure proper decoupling of the VCC and VDDQ supplies, and follow the layout guidelines in the datasheet to minimize signal skew. The differential clock inputs should be routed with controlled impedance to maintain timing accuracy.

USD $2.88 有现货
74V2T04STR - Triple Inverter CMOS, SOT-23-8 | STMicroelectronics
74V2T04STR

74V2T04STR - Triple Inverter CMOS, SOT-23-8 | STMicroelectronics

The STMicroelectronics 74V2T04STR is a high-speed CMOS triple inverter fabricated in sub-micron silicon gate C2MOS technology with double-layer metal wiring, packaged in an 8-pin SOT-23 (Tape & Reel, STR suffix). It provides three independent single-stage inverting buffers in a single small-outline package, making it a logic-level building block for digital signal inversion in space-constrained designs. Key specifications from the manufacturer datasheet include a typical propagation delay tPD of 4.7 ns at VCC = 5 V, a low quiescent supply current, and balanced output drive capability of |IOH| = IOL = 8 mA minimum at VCC = 4.5 V. A CMOS inverter is the most fundamental building block of digital logic. It accepts a single binary input and produces the complementary binary output: a logic HIGH on the input produces a logic LOW on the output, and vice versa. The 74V2T04 integrates three such inverters into one package, replacing three discrete transistor pairs or three single-inverter packages, thereby reducing board area, BOM count, and propagation skew between channels. As a CMOS device, it sits within the broader hierarchy of logic gates -> combinational logic ICs -> standard logic family -> semiconductor. Key differentiating features include TTL-compatible input thresholds of VIH = 2 V (min) and VIL = 0.8 V (max), which allow direct interfacing with 5 V TTL logic without level translation; power-down protection on inputs that prevents back-feeding current when the device is unpowered; symmetrical output impedance for matched rise and fall times; and balanced propagation delay for predictable timing margins in synchronous paths. The C2MOS silicon-gate process provides inherent low static power dissipation, with quiescent ICC remaining low across the full VCC operating range. The architecture is a classic CMOS inverter pair (p-channel pull-up, n-channel pull-down) replicated three times. Each inverter output stage is sized for the 8 mA balanced drive specification, which is sufficient for driving moderate capacitive bus loads and short PCB traces. The 4.7 ns typical propagation delay at 5 V enables use in clock squaring, reset distribution, and signal buffering applications up to several tens of megahertz. Because all three channels share the same VCC and GND pins, decoupling must be placed close to those pins to suppress switching noise. Typical applications include logic-level inversion and clock buffering in portable and battery-powered devices, signal conditioning between 5 V TTL and 3.3 V CMOS domains, oscillator and crystal-clock signal inversion, watchdog reset pulse generation, and general-purpose glue logic in microcontroller-based embedded systems. The compact SOT-23-8 footprint makes it particularly well suited to hand-held, wearable, and space-constrained consumer designs. When designing with the 74V2T04STR, place a 100 nF ceramic decoupling capacitor as close as possible to the VCC pin, route input and output traces to minimize coupling, and ensure that the load capacitance does not exceed the device's drive capability to maintain the specified propagation delay. Unused inputs must be tied to VCC or GND; floating inputs on a CMOS device can drift to the linear region and cause quiescent current to rise. This page synthesizes distributor pricing, drop-in alternative listings across ST and competing logic families, and practical PCB-level design notes not found in the manufacturer datasheet.

USD $0.14 有现货
74VHC165FT - 8-Bit PISO Shift Register, 16-TSSOP | Toshiba
74VHC165FT

74VHC165FT - 8-Bit PISO Shift Register, 16-TSSOP | Toshiba

The Toshiba 74VHC165FT is an 8-bit parallel-in/serial-out (PISO) shift register built on an advanced high-speed CMOS C2MOS silicon-gate process, offered in a 16-pin TSSOP (TSSOP16B) surface-mount package. It accepts parallel data on one rising or falling shift/load edge and serially shifts it out through Q7 or the complementary Q7' output, supporting clock frequencies up to the device's VHC-rated switching speed across a 2 V to 5.5 V supply range. The wide VCC range makes the part usable in both 3.3 V and 5 V logic families without level translation. A shift register is a sequential logic block that converts parallel data to a serial stream (PISO) or a serial stream to parallel data (SISO/PIPO). In the broader digital hierarchy it belongs to logic ICs → shift registers → CMOS logic → standard logic ICs. PISO shift registers like the 74VHC165FT are commonly used to expand microcontroller GPIO by reporting eight parallel inputs over a single serial pin, reducing board routing complexity in button/keypad scanning, multi-channel ADC front-ends, and display drivers. Key features include eight parallel inputs (D0-D7) with parallel load control (SH/LD'), a clock inhibit pin, asynchronous complementary serial outputs (Q7, Q7'), and standard CMOS low-power dissipation. The 74VHC165FT typically exhibits low quiescent current and high noise margin, making it suited for mixed-signal boards where analog and digital sections must coexist on the same supply. The TSSOP-16B footprint (also referred to as 16-TSSOP) is JEDEC-compliant and pin-compatible with industry-standard 74xx165 logic from other vendors. The architecture uses a master/slave flip-flop chain with asynchronous parallel-load steering logic. When SH/LD' is held LOW, the eight D inputs are asynchronously loaded into the register, overriding any serial activity; when SH/LD' is HIGH, the device shifts on each rising clock edge. The clock-inhibit (CK INH) and serial-data-in (SER) pins allow daisy-chaining multiple 74VHC165 devices for 16-, 24-, or 32-bit input expansion over a single serial line. Typical applications include industrial PLC digital-input modules, keyboard matrix scanners, multi-channel switch-monitor front-ends, LED driver shift chains (when paired with companion PIPO parts), and automotive body-control modules. The wide operating temperature and CMOS noise immunity make it a strong fit for factory-automation and instrumentation. When designing with this device, observe the SH/LD' pulse width (tW) and clock-to-Q propagation delay (tpd) in your timing budget; the asynchronous parallel load is the fastest way to capture a snapshot of the eight inputs but must be glitch-free. Add a small RC on SH/LD' if mechanical switches are wired directly to D inputs. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that go beyond the manufacturer datasheet to help engineers select and source the 74VHC165FT quickly.

USD $0.15 有现货
74VHC373MTCX - Octal D-Type Latch, 3-STATE, TSSOP-20 | onsemi
74VHC373MTCX

74VHC373MTCX - Octal D-Type Latch, 3-STATE, TSSOP-20 | onsemi

The onsemi 74VHC373MTCX is an advanced high-speed CMOS octal D-type transparent latch with 3-STATE outputs, fabricated with silicon-gate CMOS technology, housed in a 20-pin TSSOP package (MTC suffix). It achieves high-speed operation similar to equivalent bipolar Schottky TTL while maintaining CMOS-class low power dissipation. The device features eight D-type latches with separate latch-enable (LE) and output-enable (OE) controls, configured as an 8-bit transparent latch with non-inverting outputs and high-impedance output capability. A D-type transparent latch is a sequential logic element that captures data on its D inputs when the latch-enable signal is asserted, and holds that data on the Q outputs when LE is de-asserted. The 3-STATE outputs allow multiple devices to share a common bus, controlled by the OE pin. In the broader system hierarchy, the 74VHC373 belongs to the 74VHC logic family of high-speed CMOS logic, itself part of the larger CMOS logic IC family used for glue logic, bus buffering, and address/data demultiplexing in digital systems. Key specifications include a wide 2.0 V to 5.5 V VCC operating range, typical propagation delay of approximately 5 ns at 5 V, low quiescent current, and high output drive capability. The output structure is non-inverting, making it well suited to bus-driving applications where input and output polarities must match. An internal static-guard design provides ESD protection on every input and output pin. Typical applications include address/data bus demultiplexing in microcontroller and microprocessor systems, bus arbitration and bidirectional buffering, register file building blocks, I/O port expansion, and general-purpose storage elements in digital logic designs. The TSSOP-20 footprint makes it attractive for compact, surface-mount assemblies where board space is constrained. When designing with this part, ensure that the OE pin is correctly driven to avoid bus contention when multiple 74VHC373 devices share a common output bus. Decoupling the VCC pin with a 0.1 µF ceramic capacitor placed within a few millimeters of the package is recommended for reliable high-speed operation. This page synthesizes distributor pricing, verified cross-reference drop-in alternatives, and practical design notes beyond what is presented in the manufacturer datasheet.

USD $0.29 有现货