集成电路

子分类

📁 ADC/DAC 2519 产品 📁 放大器IC 797 产品 📁 音频编解码器 16 产品 📁 音频IC 2 产品 📁 时钟与计时 301 产品 📁 DSP 963 产品 📁 数据采集IC 2 产品 📁 数字电位器 4 产品 📁 显示驱动与控制器 1 产品 📁 FPGA与CPLD 6666 产品 📁 接口IC 1586 产品 📁 LED驱动器 1 产品 📁 逻辑IC 305 产品 📁 存储IC 875 产品 📁 微控制器 18732 产品 📁 微处理器 4 产品 📁 电机驱动器 1 产品 📁 其他 1 产品 📁 Sensor and Detector Interfaces 1 产品 📁 专用IC 15 产品 📁 视频IC 13 产品

产品（32807)

AD5291BRUZ-20 - 20kΩ 256-Position SPI Digital Potentiometer | ADI
AD5291BRUZ-20

AD5291BRUZ-20 - 20kΩ 256-Position SPI Digital Potentiometer | ADI

The Analog Devices AD5291BRUZ-20 is a single-channel, 256-position digital potentiometer with 20 kΩ end-to-end resistance, nonvolatile memory (NVM) and an SPI serial interface, housed in a 14-pin TSSOP (RU-14) package. According to the ADI AD5291/AD5292 datasheet, this part combines ±1% R-tolerance accuracy with 20-time-programmable (20-TP) memory, allowing wiper settings to be retained through power cycles without an external EEPROM. Headline parameters include 256 tap positions, 20 kΩ nominal resistance, ±1% resistor tolerance, and an SPI-compatible digital interface operating from a single 2.7 V to 5.5 V analog supply plus a 1.7 V to 5.5 V logic supply. A digital potentiometer (often abbreviated digi-pot or RDAC) is a digitally controlled variable resistor that emulates a mechanical potentiometer through a tapped resistor ladder switched by MOSFET transistors. It belongs to the broader category of digital-to-analog converters (DAC) used for resistance, which in turn sits within data-acquisition and signal-conditioning components. Compared to mechanical trimmers, a digi-pot offers remote adjustment, no mechanical wear, and software-controlled calibration. Key features of the AD5291BRUZ-20 include ±1% end-to-end resistance tolerance, a low 5 ppm/°C nominal temperature coefficient, 256 uniform tap points with 5 V/5.5 V single-supply operation, and a 20-time-programmable nonvolatile memory for storing the wiper position through power-down. The part also integrates a hardware RESET pin and software reset command that reloads the most recently programmed 20-TP memory location, plus a power-on refresh circuit that reinitializes the wiper on supply ramp. The internal architecture is a precision thin-film resistor ladder with CMOS transmission-gate switches, driven by an internal RDAC register. A separate 20-bit (AD5291) or 50-bit (AD5292) EEPROM cell stores the user-programmed wiper position. The SPI interface supports daisy-chaining of multiple devices via a dedicated SDO pin, and the logic supply range of 1.7 V to 5.5 V permits direct connection to 1.8 V, 3.3 V, or 5 V microcontrollers without level shifters. Typical applications include programmable gain amplifiers and transimpedance amplifiers, precision reference voltage trimming in instrumentation, audio volume and tone control, LCD display contrast adjustment, programmable filter cutoff and oscillator tuning, and industrial 4–20 mA loop calibration. The TSSOP-14 footprint is friendly to handheld and portable designs where board area is constrained. When designing with this device, observe the absolute maximum analog supply voltage of 6.5 V and keep the logic supply within 1.7 V to 5.5 V. Bypass VDD and VL with 0.1 µF capacitors placed within 5 mm of the supply pins, and reserve a small footprint for an optional 1 µF bulk cap on VDD if the supply is noisy. This page synthesizes distributor pricing, drop-in alternatives sourced from the AD5291 family and competitor cross-reference, and practical design notes not found in the manufacturer datasheet alone, helping engineers select and qualify the AD5291BRUZ-20 faster.

询价 联系我们
AD5292BRUZ-100-RL7 - 1024-Tap 100kΩ SPI Digital Potentiometer | Analog Devices
AD5292BRUZ-100-RL7

AD5292BRUZ-100-RL7 - 1024-Tap 100kΩ SPI Digital Potentiometer | Analog Devices

The Analog Devices AD5292BRUZ-100-RL7 is a single-channel, 1024-position digital potentiometer with 100 kΩ end-to-end resistance, nonvolatile memory (20-TP), and an SPI serial interface, housed in a 14-pin TSSOP package rated for -40°C to +105°C operation. The device features ±1% nominal resistor tolerance in R-Perf mode, ±35 ppm/°C resistance temperature coefficient, and 50 ppm typical resistor differential nonlinearity, making it one of the most precise digital pots in its class. A digital potentiometer (or digipot) is a solid-state variable resistor whose wiper position is set by a digital code rather than mechanical action. In the signal chain hierarchy it sits between passive mechanical potentiometers and active digital-to-analog converters (DACs), offering software-controlled resistance adjustment, nonvolatile state retention, and PCB-mountable miniaturization. Digipots are commonly used to replace mechanical trimmers in volume controls, gain stages, and calibration circuits. Key features of the AD5292 include 1% resistor tolerance in R-Perf mode, an SPI-compatible serial interface operating up to 50 MHz, and 20-times programmable nonvolatile memory that retains wiper position through power cycles. The 50 ppm/°C temperature coefficient and 50 ppm resistor differential nonlinearity (DNL) ensure stable, monotonic resistance steps across the operating range, which is critical for instrumentation applications. The AD5292 uses an array of 1024 thin-film resistors with CMOS switches and a wiper decoder. The thin-film process provides low noise, low temperature coefficient, and excellent long-term stability compared to polysilicon alternatives. The internal charge-pump generates the gate voltage required for the analog switches, allowing the device to operate from a single 9 V to 33 V analog supply while the digital interface is referenced to a separate 2.7 V to 5.5 V logic supply, simplifying interface to low-voltage microcontrollers. Typical applications include programmable gain amplifiers, instrumentation gain trimming, LCD contrast control, audio volume attenuation, and programmable voltage references. The wide supply range and high voltage tolerance make it well-suited for industrial 24 V bus systems and precision measurement equipment where mechanical trimmers are not acceptable. When designing with the AD5292, place 0.1 µF bypass capacitors close to the AVDD and DGND pins. The SDO pin contains an open-drain N-channel FET and requires an external pull-up resistor if used. The wiper resistance (typically 60 Ω) should be included in gain-error calculations for high-precision circuits. This page synthesizes AD5292BRUZ-100-RL7 distributor pricing, SPI-compatible drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
AD5372BSTZ - 32-Channel 16-Bit Serial DAC | Analog Devices
AD5372BSTZ

AD5372BSTZ - 32-Channel 16-Bit Serial DAC | Analog Devices

The AD5372BSTZ is a 32-channel, 16-bit digital-to-analog converter (DAC) from Analog Devices, housed in a 64-lead LQFP package. It provides buffered voltage outputs with a nominal span of 4× the reference voltage, making it ideal for precision multi-channel control systems. The device features a serial interface, independent gain and offset trim for each DAC, and operates over a wide temperature range. A digital-to-analog converter (DAC) is an electronic component that converts digital binary data into an analog voltage or current. The AD5372BSTZ belongs to the family of voltage-output DACs, which are essential in applications requiring precise analog control from digital systems, such as industrial automation, instrumentation, and communication systems. As a multi-channel DAC, it integrates 32 individual converters in a single package, reducing board space and simplifying system design. Key features of the AD5372BSTZ include 16-bit resolution, 32 independent DAC channels, and a serial interface compatible with SPI/QSPI/MICROWIRE. Each DAC has a buffered output capable of driving loads directly, and the gain and offset of each channel can be independently trimmed to remove system errors. The device operates from a single 2.5V to 5.5V supply, with a reference voltage range of 2V to 5V, and provides a nominal output span of 4× VREF. The AD5372BSTZ uses a resistor-string architecture with an output buffer for each channel, ensuring monotonicity and low glitch energy. The serial interface supports daisy-chaining, allowing multiple devices to be controlled with a single data line. The device includes a power-on reset that clears all DAC registers to zero-scale, and a CLR pin that resets outputs to zero-scale or midscale. The LQFP package provides good thermal performance and is suitable for surface-mount assembly. Typical applications include automatic test equipment (ATE), optical network control, instrumentation, and industrial process control. The 32 channels and 16-bit resolution make it suitable for systems requiring many precise analog outputs, such as multi-axis positioning, programmable voltage sources, and calibration equipment. When designing with the AD5372BSTZ, ensure adequate decoupling on the AVDD and DVDD supplies, and place the reference decoupling capacitor close to the REFIN pin. The serial clock frequency should be limited to 50 MHz to ensure reliable communication, and the SYNC pin must be held low during data transfer.

询价 联系我们
AD5381BSTZ-3 - 40-Channel 12-Bit DAC | Analog Devices
AD5381BSTZ-3

AD5381BSTZ-3 - 40-Channel 12-Bit DAC | Analog Devices

The AD5381BSTZ-3 is a complete, single-supply, 40-channel, 12-bit digital-to-analog converter (DAC) from Analog Devices, packaged in a 100-lead LQFP (14x14 mm). It operates from a 3 V single supply and includes an on-chip output amplifier with rail-to-rail operation on all 40 channels. The device features a programmable internal reference (1.25 V default, 2.5 V optional via control register), an on-chip channel monitor that multiplexes outputs to a common MON_OUT pin, and a flexible serial interface (DSP-/SPI-/MICROWIRE-compatible) or parallel interface. The AD5381BSTZ-3 is specified for the industrial temperature range (-40°C to +85°C) and is RoHS compliant. A digital-to-analog converter (DAC) is an electronic component that converts digital binary data into an analog voltage or current. In the hierarchy of signal processing, a DAC is a key element in the data converter family, which also includes analog-to-digital converters (ADCs). DACs are essential in systems where digital processing must interface with the analog world, such as in audio playback, motor control, and instrumentation. The AD5381 is a dense DAC, integrating 40 channels in a single package, which reduces board space and simplifies multi-channel systems. Key features of the AD5381BSTZ-3 include 12-bit resolution, 40 independent output channels, a settling time of 8 µs, and a programmable internal reference with 10 ppm/°C drift. The device also offers a power-on reset to zero-scale or midscale, and a clear function to reset outputs. The rail-to-rail output amplifiers allow the outputs to swing close to the supply rails, maximizing dynamic range. The channel monitor function simplifies system diagnostics by allowing external monitoring of any channel. Technically, the AD5381 uses a resistor-string architecture with an output buffer for each channel, ensuring monotonicity and low glitch. The device supports both serial and parallel interfaces, with the SER/PAR pin selecting the mode. In serial mode, the SPI/I2C pin (Pin 97) must be tied low for SPI-compatible operation. The internal reference can be programmed to 1.25 V or 2.5 V via the control register, but operating with 2.5 V reference degrades accuracy and limits input code range, as noted in the datasheet. Typical applications include industrial process control, automated test equipment, multi-channel data acquisition systems, and precision instrumentation. The 40-channel density and 3 V operation make it ideal for systems requiring many analog outputs with minimal power consumption. The device's rail-to-rail outputs and programmable reference enhance flexibility in various voltage domains. When designing with the AD5381BSTZ-3, ensure adequate decoupling on the AVDD and DVDD supplies, and consider the reference voltage selection carefully to meet accuracy requirements. The channel monitor function can be used for system-level calibration and fault detection.

询价 联系我们
AD5381BSTZ-5 - 40-Channel 12-Bit DAC | Analog Devices
AD5381BSTZ-5

AD5381BSTZ-5 - 40-Channel 12-Bit DAC | Analog Devices

The AD5381BSTZ-5 is a complete, single-supply, 40-channel, 12-bit digital-to-analog converter (DAC) from Analog Devices, housed in a 100-lead LQFP package. It operates from a single 5V supply and includes an on-chip output amplifier with rail-to-rail operation on all 40 channels. The device features a programmable internal 1.25V/2.5V reference with 10 ppm/°C drift, an on-chip channel monitor function that multiplexes analog outputs to a common MON_OUT pin, and a power-down mode. It supports both serial (SPI, DSP, MICROWIRE) and parallel interfaces, with the SER/PAR pin selecting the mode. A digital-to-analog converter (DAC) is an electronic component that converts digital binary data into an analog voltage or current. The AD5381BSTZ-5 is a multi-channel DAC, specifically a denseDAC, designed for systems requiring many precise analog outputs from a single IC. It belongs to the data acquisition product family, which includes ADCs, DACs, and analog front ends, and is essential in industrial control, automated test equipment, and instrumentation where multiple analog voltages must be generated accurately. Key features include guaranteed monotonic INL error of ±1 LSB max, a 10 ppm/°C on-chip reference, rail-to-rail output amplifiers, and a power-down mode. The device operates over the industrial temperature range of -40°C to +85°C. The 100-lead LQFP package (14x14 mm) provides a compact footprint for high-channel-count designs. The AD5381BSTZ-5 is the 5V supply version; a 3V version (AD5381BSTZ-3) is also available. Technically, the AD5381 uses a segmented architecture with an internal reference and output amplifiers, ensuring monotonicity and low INL. The channel monitor function allows external monitoring of any channel without disturbing the output, which is valuable for system diagnostics. The serial interface supports daisy-chaining for multiple devices, and the parallel interface allows high-speed updates. The power-down mode reduces current consumption to a low level, beneficial for power-sensitive applications. Typical applications include industrial process control, automated test equipment (ATE), instrumentation, and multi-channel voltage biasing in optical modules. The 40-channel density and 12-bit resolution make it ideal for systems requiring many accurate analog outputs, such as setting bias voltages in MEMS or optical devices. The rail-to-rail output and single-supply operation simplify power supply design. When designing with the AD5381BSTZ-5, ensure proper decoupling of the AVDD and DVDD supplies with 0.1µF and 10µF capacitors close to the pins. The reference output should be buffered if driving external loads. For serial mode, tie SER/PAR high and SPI/I2C low. Verify the interface timing against the datasheet to avoid data corruption.

询价 联系我们
AD5381BSTZ-5KL2 - 40-Channel 12-Bit DAC | Analog Devices
AD5381BSTZ-5KL2

AD5381BSTZ-5KL2 - 40-Channel 12-Bit DAC | Analog Devices

The AD5381BSTZ-5KL2 is a complete, single-supply, 40-channel, 12-bit digital-to-analog converter (DAC) from Analog Devices, packaged in a 100-lead LQFP. It operates from a 5 V supply and includes an on-chip output amplifier with rail-to-rail operation on all 40 channels. The device features a programmable internal 1.25 V/2.5 V reference with 10 ppm/°C drift, an on-chip channel monitor that multiplexes outputs to a common MON_OUT pin, and a flexible digital interface supporting both parallel and serial (SPI/DSP/MICROWIRE) modes. The AD5381 is designed for precision multichannel applications such as industrial process control, automatic test equipment, and medical instrumentation. A digital-to-analog converter (DAC) is an electronic component that converts digital binary data into an analog voltage or current. The AD5381 is a denseDAC, integrating 40 DAC channels in a single package, which reduces board space and system cost compared to using multiple lower-channel-count DACs. It belongs to the family of data converters, which are essential in bridging the digital and analog domains in mixed-signal systems. The AD5381's high channel density and integrated reference make it a key component in multichannel control and calibration systems. Key features of the AD5381BSTZ-5KL2 include 12-bit resolution, 40 independent output channels, rail-to-rail output amplifiers, and a programmable reference. The device offers a settling time of 8 µs typical, ensuring fast response in dynamic applications. It also includes a power-on reset to zero-scale, ensuring safe startup conditions. The channel monitor function allows external monitoring of any channel without disturbing the output, which is valuable for system diagnostics. Technically, the AD5381 uses a segmented architecture with an internal precision reference, achieving excellent linearity and low noise. The device operates over a temperature range of -40°C to +105°C, making it suitable for industrial environments. The LQFP-100 package provides a compact footprint while allowing adequate thermal dissipation. The digital interface supports both parallel and serial modes, with the SER/PAR pin selecting the mode, and the SPI/I2C pin (Pin 97) enabling the serial interface when tied low. Typical applications include industrial process control (e.g., valve and actuator control), automatic test equipment (ATE) for precise voltage generation, and medical instrumentation such as patient monitoring systems. The AD5381's 40 channels allow it to drive multiple analog outputs simultaneously, reducing component count and improving system reliability. When designing with the AD5381, ensure proper decoupling of the AVDD and DVDD supplies with 10 µF and 0.1 µF capacitors placed close to the pins. The reference output should be buffered if external loads are connected. The MON_OUT pin can be used to monitor channel outputs, but care must be taken to avoid loading the monitored channel.

询价 联系我们
AD5412ACPZ - 12-Bit Current/Voltage Output DAC | Analog Devices
AD5412ACPZ

AD5412ACPZ - 12-Bit Current/Voltage Output DAC | Analog Devices

The AD5412ACPZ is a low-cost, precision, fully integrated 12-bit digital-to-analog converter (DAC) from Analog Devices that offers a programmable current source and programmable voltage output, designed to meet the requirements of industrial process control applications. It operates from a single 10.8V to 40V supply and provides a current output range of 4 mA to 20 mA, 0 mA to 20 mA, or 0 mA to 24 mA, and a voltage output range of 0 V to 5 V, 0 V to 10 V, ±5 V, or ±10 V. The device is available in a 40-lead LFCSP-VQ (6x6 mm) package, designated by the 'CP' suffix, and is specified for operation over the extended industrial temperature range of -40°C to +85°C. A digital-to-analog converter (DAC) is a device that converts digital binary data into an analog voltage or current signal. The AD5412 is a precision DAC with an integrated output amplifier and reference buffer, enabling direct interface to actuators, transmitters, and other industrial control elements. It belongs to the family of smart DACs that combine digital-to-analog conversion with programmable output ranges and diagnostic features, making it a key component in programmable logic controllers (PLCs), distributed control systems (DCS), and field transmitters. Key features of the AD5412ACPZ include a 12-bit resolution with monotonicity guaranteed, a flexible serial interface compatible with SPI, QSPI, and MICROWIRE protocols, and an on-chip precision reference (2.5V) with a temperature coefficient of 10 ppm/°C. The device also includes a HART (Highway Addressable Remote Transducer) compliant interface, allowing it to be used in smart transmitters that require superimposed digital communication on the analog current loop. The output is protected against short circuits and can drive capacitive loads up to 1 µF. Technically, the AD5412 uses a segmented architecture with a precision current-steering DAC core, followed by a programmable gain amplifier and output driver. The device includes a power-on reset circuit that ensures the output is at zero-scale or mid-scale on power-up, and a clear pin that resets the output to a defined state. The digital interface supports daisy-chaining for multiple devices on a single serial bus, and the device can be configured for either current or voltage output mode via the control register. Typical applications include industrial process control, PLC analog output modules, HART transmitters, and actuator control. The AD5412's ability to provide both current and voltage outputs with high accuracy and low drift makes it ideal for driving valves, positioners, and other field devices. Its HART compatibility enables seamless integration into existing 4-20 mA loop infrastructure. When designing with the AD5412ACPZ, ensure that the supply voltage is adequately decoupled with a 10 µF tantalum capacitor and a 0.1 µF ceramic capacitor placed close to the AVDD and DVDD pins. The reference output should be buffered if external loads are connected, and the output amplifier's stability should be verified with the expected capacitive load. For best performance, use a clean analog ground plane and separate digital and analog supply traces.

询价 联系我们
AD5412ACPZ-REEL7 - 12-Bit DAC with Current/Voltage Output | ADI
AD5412ACPZ-REEL7

AD5412ACPZ-REEL7 - 12-Bit DAC with Current/Voltage Output | ADI

The AD5412ACPZ-REEL7 is a low-cost, precision, fully integrated 12-bit digital-to-analog converter (DAC) from Analog Devices, offering a programmable current source and programmable voltage output. It is designed to meet the requirements of industrial process control applications, providing a single-channel output with serial input interface. The device operates from a 40-lead LFCSP-VQ (6x6 mm) package, ensuring compactness for space-constrained designs. A digital-to-analog converter (DAC) is an electronic component that converts digital binary data into an analog voltage or current signal. The AD5412 belongs to the family of precision DACs used in industrial automation, where accurate analog output is essential for controlling actuators, valves, and transmitters. It integrates a current source and voltage output capability, making it versatile for various control loops. Key features include 12-bit resolution, a programmable current output range (typically 4-20 mA) and voltage output range (0-5 V, 0-10 V, ±5 V, ±10 V), and a serial interface compatible with SPI. The device also includes a power-on reset, ensuring the output is at a known state on power-up. Its low power consumption and wide operating temperature range (-40°C to +125°C) make it suitable for harsh industrial environments. Technically, the AD5412 uses a resistor-string architecture with an output amplifier, providing monotonic performance and low glitch energy. It includes a precision internal reference (optional external reference) and a flexible digital interface that supports daisy-chaining. The device is fully specified over the industrial temperature range, ensuring reliable operation in demanding applications. Typical applications include industrial process control, programmable logic controllers (PLCs), actuator control, and transmitter calibration. The AD5412's ability to provide both current and voltage outputs makes it ideal for interfacing with various sensors and actuators in factory automation. When designing with the AD5412, ensure proper decoupling of the power supply and reference pins. The output amplifier requires a stable supply; consider using a low-noise LDO for analog rails. Also, the thermal pad should be soldered to a large copper area for effective heat dissipation.

询价 联系我们
AD5422ACPZ - 16-Bit Current/Voltage Output DAC | Analog Devices
AD5422ACPZ

AD5422ACPZ - 16-Bit Current/Voltage Output DAC | Analog Devices

The AD5422ACPZ is a single-channel, 16-bit digital-to-analog converter (DAC) from Analog Devices, designed for industrial process control applications. It provides a programmable current source and programmable voltage output, with HART connectivity capability. The device operates from a single 10.8V to 40V supply and is available in a 40-lead LFCSP-VQ (6x6 mm) package. It features a serial interface compatible with SPI, QSPI, and MICROWIRE protocols, and includes an on-chip reference and output amplifier. A DAC (digital-to-analog converter) is an electronic component that converts digital binary data into an analog voltage or current. The AD5422 is a precision DAC that integrates a current source and voltage output, making it a complete analog output stage for industrial control systems. It belongs to the family of smart DACs that combine digital-to-analog conversion with additional features like fault detection and HART communication. Key features include 16-bit resolution, a current output range of 4 mA to 20 mA (with additional ranges), a voltage output range of 0 V to 5 V, 0 V to 10 V, ±5 V, and ±10 V, and a settling time of 10 µs. The device offers a total unadjusted error (TUE) of ±0.1% FSR, and includes a precision 5 ppm/°C internal reference. It also features a flexible serial interface, a power-on reset to zero-scale, and a fault alarm output. The AD5422 uses a segmented architecture with a precision resistor ladder and a high-speed output amplifier. It includes a programmable gain and offset, and supports HART signal modulation for smart transmitter applications. The device operates over a temperature range of -40°C to +85°C and is available in a lead-free, RoHS-compliant package. Typical applications include process control, PLC analog output modules, industrial automation, and HART network transmitters. The AD5422's high accuracy and flexibility make it suitable for driving actuators, valves, and other analog control elements. When designing with the AD5422, ensure proper decoupling of the AVDD and DVDD supplies, and use a clean analog ground plane. The device requires an external reference for best performance, and the output amplifier can drive capacitive loads up to 1000 pF.

询价 联系我们
AD5422ACPZ-REEL7 - 16-Bit V/I Out DAC | Analog Devices
AD5422ACPZ-REEL7

AD5422ACPZ-REEL7 - 16-Bit V/I Out DAC | Analog Devices

The AD5422ACPZ-REEL7 is a single-channel, 16-bit, serial input, current source and voltage output digital-to-analog converter (DAC) from Analog Devices, designed for industrial process control applications. It is housed in a 40-lead LFCSP-VQ (6x6 mm) package and operates over a wide supply range. The device integrates a programmable current source (0 mA to 24 mA) and a programmable voltage output (0 V to 5 V, 0 V to 10 V, ±5 V, ±10 V), making it highly versatile for actuator control, PLCs, and transmitter systems. A digital-to-analog converter (DAC) is an electronic circuit that converts digital binary data into an analog voltage or current. The AD5422 belongs to the family of precision DACs used in industrial control loops, where it translates digital setpoints from a microcontroller or FPGA into precise analog signals that drive valves, motors, or transmitters. It is a key component in the signal chain from digital control to physical actuation, bridging the digital and analog domains. Key features include 16-bit resolution, a flexible serial interface (SPI-compatible), and an on-chip precision reference. The device offers a monotonic output with low integral nonlinearity (INL) and differential nonlinearity (DNL), ensuring accurate analog representation. It also includes a HART (Highway Addressable Remote Transducer) connectivity mode, allowing the DAC to superimpose a frequency-shift keying (FSK) signal on the current loop for smart transmitter communication. The AD5422 uses a segmented architecture with a precision resistor ladder and a programmable gain amplifier to achieve its output ranges. It operates from a single 10.8 V to 40 V supply for the current loop and a separate digital supply (2.7 V to 5.5 V), enabling direct interface with low-voltage logic. The device includes a power-on reset, a clear pin, and a fault alarm output, enhancing system reliability. Typical applications include industrial process control, PLC analog output modules, HART transmitters, and actuator control. Its high accuracy and flexible output ranges make it suitable for both current-loop and voltage-output systems, reducing component count and board space. When designing with the AD5422, ensure proper decoupling of the AVDD and DVDD supplies, and consider the thermal performance of the LFCSP package when driving high current loads. The HART mode requires careful filtering to avoid signal distortion.

询价 联系我们
AD5535ABCZ - 32-Channel 14-Bit DAC, 50-200V | Analog Devices
AD5535ABCZ

AD5535ABCZ - 32-Channel 14-Bit DAC, 50-200V | Analog Devices

The AD5535ABCZ is a 32-channel, 14-bit digital-to-analog converter (DAC) with an integrated high-voltage output amplifier, manufactured by Analog Devices. It is housed in a 124-ball CSPBGA (15x15 mm) package and is specifically designed for optical microelectromechanical systems (MEMS) and other high-voltage precision control applications. The device features a full-scale output voltage programmable from 50 V to 200 V via the reference input, with a 700 μA drive capability per channel. It guarantees monotonicity and offers a 1.2 MHz channel update rate, making it suitable for high-speed, multi-channel systems. A DAC (digital-to-analog converter) is an electronic component that converts digital binary data into an analog voltage or current. The AD5535 is a high-voltage, multi-channel DAC, which falls under the category of data acquisition components, specifically within the broader family of digital-to-analog converters. These devices are essential in systems where precise analog control signals must be generated from digital processing, such as in industrial automation, test equipment, and MEMS control. The AD5535's high-voltage output capability distinguishes it from standard low-voltage DACs, enabling direct drive of actuators and other high-voltage loads. Key features of the AD5535ABCZ include its 32 independent channels, each with a 14-bit resolution, ensuring fine analog output steps. The integrated high-voltage amplifier eliminates the need for external amplification, simplifying design and reducing component count. The device also includes an integrated silicon diode for temperature monitoring, which is critical for thermal management in high-power applications. The serial interface is DSP- and microcontroller-compatible, and an asynchronous RESET facility allows for quick system initialization. From a technical perspective, the AD5535 utilizes a segmented architecture to achieve 14-bit accuracy while maintaining a small die size. The output amplifier is capable of sourcing 700 μA, which is sufficient for driving capacitive loads typical in MEMS applications. The reference input allows the full-scale output to be set between 50 V and 200 V, providing flexibility for various system requirements. The device operates over a temperature range of -10°C to +85°C, as indicated in the datasheet. Typical applications include optical MEMS systems, where precise high-voltage control of micro-mirrors or other actuators is required. It is also used in industrial process control, automated test equipment, and medical instrumentation that demands high-voltage analog outputs. The AD5535's high channel count and update rate make it ideal for multi-axis control systems. When designing with the AD5535, it is important to consider the power dissipation, as the high-voltage output stages can generate significant heat. Proper PCB layout with adequate thermal vias and a solid ground plane is recommended. Additionally, the reference input should be bypassed with a low-ESR capacitor to ensure stable operation.

询价 联系我们
AD5535ABCZ-REEL7 - 32-Channel 14-Bit DAC | Analog Devices
AD5535ABCZ-REEL7

AD5535ABCZ-REEL7 - 32-Channel 14-Bit DAC | Analog Devices

The AD5535ABCZ-REEL7 is a 32-channel, 14-bit digital-to-analog converter (DAC) with an integrated high-voltage output amplifier, designed for precision control in optical microelectromechanical systems (MEMS) and other high-voltage applications. Housed in a 124-ball CSPBGA (15x15 mm) package, this device offers a full-scale output voltage programmable from 50 V to 200 V via the reference input, with a 700 μA drive capability. The AD5535 guarantees monotonicity and includes an integrated silicon diode for temperature monitoring, making it suitable for demanding industrial and scientific instrumentation. A DAC is a device that converts digital signals into analog voltages or currents. The AD5535 is a specific type of DAC with multiple channels and high-voltage outputs, enabling precise control of actuators, piezoelectric devices, and other high-voltage loads. It belongs to the family of data converters, which are essential in bridging the digital and analog worlds in electronic systems. Key features include a 1.2 MHz channel update rate, an asynchronous RESET facility, and a DSP-/microcontroller-compatible serial interface. The device operates over a wide temperature range and is available in a compact CSPBGA package, facilitating high-density PCB layouts. The integrated high-voltage amplifier eliminates the need for external amplification stages, simplifying design and reducing component count. The AD5535 utilizes a segmented architecture to achieve 14-bit resolution with guaranteed monotonicity, ensuring accurate and predictable output across the full range. The high-voltage output stage is capable of driving capacitive loads typical of MEMS actuators, with a slew rate sufficient for real-time control applications. The integrated temperature diode provides a means for thermal monitoring, enabling system-level protection and calibration. Typical applications include optical MEMS mirror arrays, adaptive optics systems, precision voltage biasing, and automated test equipment. The device's ability to generate high voltages with high resolution makes it ideal for controlling piezoelectric actuators and electrostatic MEMS devices. When designing with the AD5535, it is important to consider the thermal dissipation of the high-voltage output stage and to provide adequate decoupling on the power supply pins. The reference input should be driven by a low-noise, stable voltage source to achieve optimal performance.

询价 联系我们
AD5545BRUZ - Dual 16-Bit Current-Output DAC | Analog Devices
AD5545BRUZ

AD5545BRUZ - Dual 16-Bit Current-Output DAC | Analog Devices

The Analog Devices AD5545BRUZ is a dual, 16-bit, current-output, serial-input digital-to-analog converter (DAC) housed in a 16-pin TSSOP (RU-16) package. It operates from a single 4.5V to 5.5V supply and delivers ±1 LSB DNL monotonicity with ±1 LSB INL linearity. The full-scale output current is 2 mA ±20%, set by an external reference voltage, and an internal feedback resistor (RFB) simplifies I-to-V conversion when combined with an external op amp such as the AD8038. A multiplying DAC is a converter whose output is the product of a digital input code and an analog reference voltage, enabling four-quadrant operation when bipolar signals are applied. The AD5545 belongs to the current-output multiplying DAC category, which sits within the broader hierarchy of digital-to-analog converters -> data converters -> mixed-signal ICs -> semiconductor devices. Current-output architectures are favored where the reference must vary with a signal (such as in gain control, attenuators, or automatic test equipment) rather than being a fixed precision voltage. Key features include a 2Q multiplying reference input, 0.5 µs full-scale settling time, and a bipolar output swing of up to ±15 V when used with an external high-voltage op amp. The serial interface is SPI/QSPI/MICROWIRE-compatible and supports high-speed write cycles. The dual-channel integration makes the device suitable for complex waveform generation, I/Q signal synthesis, and simultaneous update applications. Typical applications include programmable gain/attenuation stages, digital waveform synthesis, ATE (automatic test equipment) calibration, industrial process control, and precision instrumentation. The wide reference input bandwidth allows the AD5545 to function as a digitally controlled variable attenuator when paired with a high-speed current-to-voltage op amp. When designing with this DAC, ensure the external I-to-V op amp has sufficient bandwidth and slew rate to settle within the 0.5 µs specification. Decouple VDD with a 1 µF tantalum plus 0.1 µF ceramic combination placed close to the supply pin, and route the analog ground return directly to the load to avoid ground-loop errors. This page synthesizes distributor pricing, parametric data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
AD5545BRUZ-REEL7 - Dual 16-Bit I-Out DAC | Analog Devices
AD5545BRUZ-REEL7

AD5545BRUZ-REEL7 - Dual 16-Bit I-Out DAC | Analog Devices

The Analog Devices AD5545BRUZ-REEL7 is a dual, 16-bit, current-output, serial-input digital-to-analog converter (DAC) housed in a 16-pin TSSOP package. It operates from a single 5 V supply with bipolar output swing capability up to +/-15 V, requires an external reference to set the full-scale output current, and provides 2 mA full-scale current with +/-20% accuracy relative to VREF. Each channel settles to within +/-1 LSB in 0.5 us, supporting high-precision signal generation. A multiplying DAC is a converter whose output is the product of a digital code and an analog reference input. This category sits within the broader hierarchy of digital-to-analog converters -> data converters -> mixed-signal ICs -> semiconductors. Multiplying DACs are typically implemented with R-2R ladder networks because the architecture allows the reference input to vary (including AC) without disturbing monotonicity, and is therefore preferred over resistor-string designs when 4-quadrant multiplication, bipolar operation, or wide reference range is required. Key features of the AD5545 include +/-1 LSB DNL (monotonic), +/-1 LSB INL, a 3-wire serial interface (SDI, CLK, CS) compatible with microcontrollers, and an LDAC function that allows simultaneous update of both DAC outputs. The internal reset logic supports power-on preset and dynamic reset at either zero or midscale, configurable via the MSB pin. Input reference voltages are accepted in the range of -12 V to +12 V with a constant nominal input resistance of 5 kohm +/-30%, enabling 4-quadrant multiplication. Internally the AD5545/AD5555 use a matched thin-film R-2R ladder network per channel with CMOS switches steered by the input register, a precision bandgap-based reference input conditioning network, and an LDAC-triggered double-buffered latch architecture. This topology delivers low gain error and excellent DC accuracy while keeping digital feedthrough low. AC reference inputs are also accommodated, making the part suitable for waveform generation and audio gain control. Typical applications include precision instrumentation, automatic test equipment (ATE) level setting, digitally controlled calibration, waveform synthesis, audio gain control, and industrial process control. The wide bipolar output swing and multiplying capability make it especially attractive for four-quadrant signal chains and high-accuracy analog output modules in PLC and data-acquisition systems. When designing with the AD5545, choose a low-offset, low-noise op-amp such as the AD8038 or AD8065 for the I-to-V conversion stage, and lay out the TSSOP footprint with analog/digital ground partitioning. Reference decoupling with 0.1 uF close to the REF pin is recommended, and the LDAC line should be tied high for simultaneous update operation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving the engineer a faster path from selection to qualified PCB.

询价 联系我们
AD561SD/883B - 10-Bit Monolithic DAC | Analog Devices
AD561SD/883B

AD561SD/883B - 10-Bit Monolithic DAC | Analog Devices

The AD561SD/883B is a 10-bit digital-to-analog converter (DAC) from Analog Devices, featuring a high-stability voltage reference integrated on a single monolithic chip. It is packaged in a 16-pin hermetically sealed ceramic DIP (CDIP) and is designed for military temperature range operation from -55°C to +125°C. The device uses ten precision high-speed current-steering switches, a control amplifier, and a laser-trimmed thin-film SiCr resistor network to produce a fast, accurate analog output current. A digital-to-analog converter (DAC) is an electronic component that converts digital binary data into an analog voltage or current. The AD561SD/883B is a current-output DAC, meaning it outputs a current proportional to the digital input, which can be converted to a voltage using an external op-amp. DACs are fundamental building blocks in data acquisition systems, where they generate analog signals for control, waveform generation, and audio applications. The AD561SD/883B belongs to the family of precision DACs, offering 10-bit resolution and a built-in reference, simplifying system design. Key features of the AD561SD/883B include its 10-bit resolution, monolithic construction with integrated voltage reference, and military-grade screening. The device operates over the full military temperature range of -55°C to +125°C, making it suitable for aerospace and defense applications. The hermetically sealed ceramic DIP package ensures reliability in harsh environments. The laser-trimmed thin-film resistor network provides excellent linearity and accuracy, with a typical settling time of [DATA_NEEDED: settling time] and a gain error of [DATA_NEEDED: gain error]. The AD561SD/883B is designed for high-performance applications where precision and reliability are critical. Its current output can be easily converted to a voltage using an external operational amplifier, and the integrated reference eliminates the need for an external reference source. The device is pin-compatible with other members of the AD561 family, allowing for easy upgrades or replacements. The military-grade screening ensures compliance with stringent quality standards, making it ideal for mission-critical systems. Typical applications include military avionics, radar systems, industrial process control, and test and measurement equipment. The wide operating temperature range and hermetically sealed package make it suitable for extreme environments. When designing with the AD561SD/883B, ensure proper decoupling on the power supply pins and consider the output current-to-voltage conversion circuit to achieve optimal performance.

询价 联系我们
AD561TD/883B - 10-Bit DAC, Military Grade | Analog Devices
AD561TD/883B

AD561TD/883B - 10-Bit DAC, Military Grade | Analog Devices

The AD561TD/883B is a low-cost, 10-bit monolithic digital-to-analog converter (DAC) manufactured by Analog Devices, designed for military-grade applications. It features a 10-bit resolution with a settling time of 500 ns, ensuring fast and accurate conversion for high-speed systems. The device operates from a single +5V supply and provides a bipolar output range of ±5V, making it suitable for a wide range of analog output applications. Housed in a 16-pin CERDIP package, the AD561TD/883B is designed for through-hole mounting, offering robust mechanical stability in harsh environments. A digital-to-analog converter (DAC) is an electronic component that converts digital binary data into an analog voltage or current. The AD561TD/883B is a specific type of DAC known as a multiplying DAC, which allows the reference voltage to be varied to produce a scaled output. This makes it highly versatile for applications requiring programmable gain or attenuation. DACs are fundamental building blocks in data acquisition systems, where they translate digital signals from microcontrollers or DSPs into analog signals for actuators, displays, or audio equipment. Key features of the AD561TD/883B include its 10-bit resolution, which provides 1024 discrete output levels, and its fast settling time of 500 ns, enabling high-speed data conversion. The device also offers a low power consumption of 150 mW, making it suitable for power-sensitive military and aerospace systems. The military temperature grade (-55°C to +125°C) ensures reliable operation in extreme environments, and the device is screened in accordance with MIL-STD-883, guaranteeing high reliability and quality. Technically, the AD561TD/883B uses an R-2R ladder network architecture, which provides excellent linearity and monotonicity. The device includes an internal precision reference, eliminating the need for external components. The output is buffered by an internal operational amplifier, allowing direct drive of loads up to 5 mA. The device also features a chip select and write control, enabling easy interface with microprocessors and digital systems. Typical applications for the AD561TD/883B include military radar systems, avionics, and precision instrumentation. Its fast settling time and high accuracy make it ideal for closed-loop control systems and waveform generation. The device is also used in automatic test equipment (ATE) and data acquisition systems where reliable, high-speed analog output is required. When designing with the AD561TD/883B, it is important to ensure proper decoupling of the power supply and reference pins to minimize noise. The output should be buffered if driving loads greater than 5 mA. Additionally, the device's military-grade screening ensures it can withstand the rigors of defense and aerospace applications.

询价 联系我们
AD567SD/883B - 12-Bit DAC, 28-CDIP | Analog Devices
AD567SD/883B

AD567SD/883B - 12-Bit DAC, 28-CDIP | Analog Devices

The AD567SD/883B is a complete high-speed 12-bit digital-to-analog converter (DAC) from Analog Devices, featuring a high-stability buried zener voltage reference and a double-buffered input latch on a single chip. It is packaged in a 28-pin ceramic dual-in-line package (CDIP) and is designed for military and aerospace applications, meeting MIL-STD-883 Class B standards. The device provides a 12-bit resolution with a settling time of typically 500 ns, ensuring fast and accurate analog output for demanding applications. A digital-to-analog converter (DAC) is an electronic component that converts digital binary data into an analog voltage or current. The AD567SD/883B is a voltage-output DAC that uses 12 precision high-speed bipolar current-steering switches and a laser-trimmed thin-film resistor network to achieve high accuracy and fast settling. It is part of the AD567 family of DACs, which are known for their reliability and performance in industrial and military environments. Key features of the AD567SD/883B include a 12-bit resolution, a buried zener reference for low drift, a double-buffered input latch for microprocessor compatibility, and a settling time of 500 ns. The device operates from a +5V and -5V supply, with a full-scale output range of 0V to +10V. It also features a power-on reset that clears the output to zero scale, ensuring predictable startup behavior. The AD567SD/883B is designed for high-reliability applications, with a ceramic package that provides excellent thermal and mechanical stability. The device is fully specified over the military temperature range of -55°C to +125°C, making it suitable for avionics, defense systems, and other harsh environments. Its double-buffered input allows for simultaneous update of multiple DACs, which is critical in multi-channel systems. Typical applications include precision instrumentation, automatic test equipment, military radar systems, and industrial process control. The device's fast settling time and high accuracy make it ideal for waveform generation and closed-loop control systems. When designing with the AD567SD/883B, ensure proper decoupling of the power supplies and a clean analog ground plane to minimize noise. The reference output should be buffered if driving external loads. The device is a mature product and may be subject to obsolescence; verify availability before new designs.

询价 联系我们
AD5700-1ACPZ - HART FSK Modem IC | Analog Devices
AD5700-1ACPZ

AD5700-1ACPZ - HART FSK Modem IC | Analog Devices

The AD5700-1ACPZ is a single-chip HART FSK half-duplex modem from Analog Devices, designed to comply with the HART physical layer requirements. It integrates all necessary filtering, signal detection, modulation, demodulation, and signal generation functions, requiring few external components. The device operates over a supply voltage range of 2.7V to 5.5V and is available in a 24-lead LFCSP-WQ (4x4 mm) package. It features a maximum supply current of 115 µA, making it ideal for loop-powered applications. The AD5700-1 variant includes an integrated 0.5% precision oscillator, saving board space and external component count. A HART modem is a specialized integrated circuit that enables digital communication over analog 4-20 mA current loops, commonly used in industrial process automation. It modulates and demodulates Frequency Shift Keying (FSK) signals at 1200 Hz and 2200 Hz, allowing digital data to be superimposed on the analog signal without interference. The HART protocol is a hybrid analog/digital standard widely adopted in smart transmitters, actuators, and control systems. The AD5700-1ACPZ belongs to the category of communication ICs, specifically modems, and is a key component in industrial communication systems. Key features include a 0.5% precision oscillator, low power consumption of 115 µA, and compliance with HART physical layer specifications. The device supports both master and slave configurations, making it versatile for various applications. It also includes an internal voltage reference and a carrier detect output, simplifying system design. The operating temperature range is -40°C to +125°C, suitable for harsh industrial environments. Technically, the AD5700-1 uses a digital signal processing architecture to achieve reliable FSK modulation and demodulation. The integrated oscillator eliminates the need for an external crystal, reducing component count and board space. The device also features a UART interface for easy connection to microcontrollers. The LFCSP package provides excellent thermal performance and a compact footprint, ideal for space-constrained designs. Typical applications include smart transmitters, process control systems, field instruments, and HART-based communication interfaces. The low power consumption and integrated oscillator make it particularly suitable for loop-powered devices where power is limited. The device is also used in HART master systems, such as handheld communicators and control room equipment. When designing with the AD5700-1ACPZ, ensure proper decoupling of the power supply and careful layout of the analog front-end to minimize noise. The device requires a few external components, including a coupling capacitor and a protection circuit for the HART signal path. Refer to the datasheet for recommended application circuits and layout guidelines.

询价 联系我们
AD5700-1BCPZ - HART FSK Modem IC | Analog Devices
AD5700-1BCPZ

AD5700-1BCPZ - HART FSK Modem IC | Analog Devices

The AD5700-1BCPZ is a single-chip HART FSK half-duplex modem from Analog Devices, designed to comply with the HART physical layer requirements. It integrates all necessary filtering, signal detection, modulation, demodulation, and signal generation functions, requiring few external components. The device operates from a 2.7V to 5.5V supply and features an internal oscillator, eliminating the need for an external crystal. It is available in a compact 24-lead LFCSP-WQ (4x4 mm) package, making it ideal for space-constrained industrial applications. A HART modem is a specialized integrated circuit that enables communication over legacy 4-20 mA analog loops by superimposing a digital frequency-shift keying (FSK) signal. The HART protocol uses two frequencies: 1200 Hz for logic '1' and 2200 Hz for logic '0', allowing simultaneous analog and digital communication. The AD5700-1BCPZ is part of the HART modem product family, which falls under the broader category of industrial communication ICs, specifically interface ICs for process automation. Key features of the AD5700-1BCPZ include a low power consumption of 1 mA typical, an integrated receive band-pass filter that can be bypassed, and an internally buffered HART output with high drive capability. The device also includes an internal 2.5V reference and supports a wide operating temperature range of -40°C to +125°C. The LFCSP package provides excellent thermal performance and a small footprint, suitable for high-density designs. Technically, the AD5700-1BCPZ uses a digital signal processing (DSP) architecture to implement the HART modem functions, ensuring accurate and reliable communication. The integrated filter eliminates the need for external components, simplifying the design and reducing bill of materials cost. The device is fully compliant with the HART physical layer specification, ensuring interoperability with other HART-compliant devices. Typical applications include industrial process control, smart transmitters, valve positioners, and other field instruments that require HART communication. The low power consumption and small package make it suitable for loop-powered devices where power budget is critical. The internal oscillator further reduces component count, making it an excellent choice for compact designs. When designing with the AD5700-1BCPZ, ensure proper decoupling of the power supply and careful layout of the analog and digital sections to minimize noise. The device requires a few external components, including a coupling capacitor and a protection circuit for the HART signal path. Refer to the datasheet for detailed application circuits and recommended component values.

询价 联系我们
AD5700-1BCPZ-RL - HART Modem IC with Oscillator | Analog Devices
AD5700-1BCPZ-RL

AD5700-1BCPZ-RL - HART Modem IC with Oscillator | Analog Devices

The AD5700-1BCPZ-RL is a single-chip HART FSK half-duplex modem from Analog Devices, designed to comply with the HART physical layer requirements. It integrates all necessary filtering, signal detection, modulation, demodulation, and signal generation functions, requiring few external components. The device operates from a 2.7V to 5.5V supply and features an integrated oscillator, eliminating the need for an external crystal. It is available in a compact 24-lead LFCSP-WQ (4x4 mm) package, suitable for space-constrained industrial applications. A HART modem is a specialized integrated circuit that enables communication over legacy 4-20 mA analog loops by superimposing a frequency-shift keying (FSK) digital signal. The AD5700-1 is part of the HART modem product family, which falls under the broader category of industrial communication ICs. These devices are essential in process automation, allowing digital configuration and diagnostics without disrupting analog measurement signals. Key features include a low-power design with a typical supply current of 86 µA in listen-only mode, an integrated receive band-pass filter that can be bypassed, and an internally buffered HART output for high drive capability. The device also includes an internal reference, a RESET pin for power-down mode, and a REF_EN pin to control the internal reference. The integrated oscillator provides a precise 1.2 MHz clock, simplifying the design and reducing component count. The AD5700-1 uses a digital signal processing (DSP) architecture to implement the HART protocol, ensuring reliable communication over long cable runs. The device supports data rates of 1200 bps, the standard HART speed, and is fully compliant with the HART physical layer specification. The LFCSP package offers excellent thermal performance and a small footprint, making it ideal for loop-powered transmitters and other compact field instruments. Typical applications include industrial process control, smart transmitters, valve positioners, and other field instruments that require HART communication. The device interfaces easily with Analog Devices' industrial converters, such as the AD5421 loop-powered current-output DAC, enabling complete smart transmitter solutions. When designing with the AD5700-1, ensure proper decoupling on the supply pins and follow the recommended layout in the datasheet to minimize noise. The RESET pin can be used to place the device in power-down mode, reducing current consumption to 1 µA, which is critical for loop-powered applications.

询价 联系我们
AD5700-1BCPZ-RL7 - Low Power HART Modem | Analog Devices
AD5700-1BCPZ-RL7

AD5700-1BCPZ-RL7 - Low Power HART Modem | Analog Devices

The AD5700-1BCPZ-RL7 is a single-chip HART FSK half-duplex modem from Analog Devices, designed to meet HART physical layer requirements for industrial field instrumentation. Housed in a 24-LFCSP-WQ (4x4) package, this low-power modem operates from a 1.71 V to 5.5 V supply and draws a maximum of 115 µA in receive mode, making it suitable for loop-powered and intrinsically safe applications. The AD5700-1 variant integrates a precision internal oscillator, eliminating the need for an external crystal and reducing component count and board area. A HART modem is a communication IC that superimposes digital Frequency Shift Keying (FSK) signals onto a 4-20 mA analog current loop, using 1200 Hz and 2200 Hz sinusoidal tones to represent logic '1' and logic '0'. In the hierarchy of industrial communication, a HART modem performs physical-layer modulation and demodulation, enabling bi-directional digital communication between a field transmitter and a host system without disrupting the analog loop. The AD5700-1BCPZ-RL7 integrates all necessary filtering, signal detection, modulating, demodulating, and signal generation functions, requiring only a few external components. Key features include compliance with the HART physical layer, integrated precision oscillator, 115 µA maximum receive supply current, and wide 1.71 V to 5.5 V operating range. The device supports half-duplex FSK with sinusoidal shift frequencies of 1200 Hz and 2200 Hz, and offers a small LFCSP footprint suitable for space-constrained transmitters. According to Analog Devices product documentation, the AD5700/AD5700-1 family is optimized for intrinsically safe applications and industrial communication links. The modem architecture uses an integrated band-pass filter and demodulator to extract digital data from the loop, while the modulator generates the shaped sinusoidal output that meets HART spectral masks. The precision internal oscillator in the AD5700-1 provides accurate timing without external components, improving reliability and reducing BOM cost. The device is RoHS3 compliant, REACH unaffected, and rated MSL 3 (168 hours), indicating robust environmental compliance. Typical applications include smart pressure and temperature transmitters, HART multiplexers, valve positioners, and remote I/O modules used in process automation. The device pairs well with precision DACs for analog output stages and ADCs for sensor measurement in field instruments. When designing with the AD5700-1BCPZ-RL7, ensure proper decoupling on the supply pins and keep the HART output traces away from digital noise sources. Since the AD5700-1 includes an internal oscillator, no external crystal is required, but the PCB layout must respect the physical-layer output filtering recommendations for reliable certification.

询价 联系我们
AD570SD/883B - 8-Bit ADC, 25us, MIL-STD-883B | Analog Devices
AD570SD/883B

AD570SD/883B - 8-Bit ADC, 25us, MIL-STD-883B | Analog Devices

The AD570SD/883B is a monolithic 8-bit successive approximation analog-to-digital converter (ADC) manufactured by Analog Devices, processed to MIL-STD-883B Class B for military and high-reliability applications. It integrates a DAC, voltage reference, clock, comparator, successive approximation register, and output buffers on a single chip, requiring no external components for a full-accuracy 8-bit conversion in 25 microseconds. The device operates from -15 V and +5 V supplies (also functional with -12 V) and is packaged in a side-brazed ceramic DIP-18 (SBDIP) with an operating temperature range of -55°C to +125°C. An analog-to-digital converter (ADC) is an electronic component that converts continuous analog signals into discrete digital numbers, enabling digital systems to process real-world signals. The AD570 is a successive approximation ADC, a type that uses a binary search algorithm to converge on the digital representation, balancing speed and resolution. It belongs to the broader category of data converters, which are essential in signal processing chains bridging analog sensors and digital processors. Key features include 8-bit resolution, a conversion time of 25 microseconds, and a parallel output interface with 8-bit access. The device offers unipolar and bipolar input ranges, with full-scale calibration and offset adjustments. It is guaranteed to operate with -15 V and +5 V supplies, and also supports -12 V operation. The military-grade processing ensures reliability in harsh environments, with a temperature range of -55°C to +125°C. Technically, the AD570 integrates all conversion functions on a single chip, eliminating the need for external clock or reference components. The successive approximation architecture provides a deterministic conversion time, making it suitable for real-time sampling. The device features a tri-state output buffer for bus-oriented systems, and its bipolar input capability allows direct connection to bipolar analog signals without external level shifting. Typical applications include military avionics, industrial process control, data acquisition systems, and test and measurement equipment where high reliability and wide temperature operation are critical. The AD570SD/883B is particularly suited for legacy military systems requiring a drop-in replacement for the original AD570. When designing with this device, ensure proper supply decoupling and consider the input impedance and settling time for accurate conversions. The device's parallel interface simplifies connection to microprocessors, but timing requirements must be observed for reliable data transfer.

询价 联系我们
AD571SD/883B - 10-Bit A/D Converter | Analog Devices | Military
AD571SD/883B

AD571SD/883B - 10-Bit A/D Converter | Analog Devices | Military

The AD571SD/883B is a complete 10-bit successive approximation analog-to-digital converter (ADC) from Analog Devices, designed for high-reliability military and aerospace applications. It integrates a precision voltage reference, clock, and comparator in a single 18-pin side-brazed ceramic DIP (SBDIP) package, offering a compact and robust solution for converting analog signals to digital data. The device accepts either unipolar (0 V to +10 V) or bipolar (-5 V to +5 V) analog inputs, selectable by grounding or opening a single pin, and provides true 10-bit accuracy with no missing codes over its full operating temperature range of -55°C to +125°C. An analog-to-digital converter (ADC) is an electronic component that transforms a continuous analog voltage into a discrete digital number proportional to the amplitude of the signal. The AD571SD/883B is a successive approximation register (SAR) ADC, which uses a binary search algorithm to determine the digital output. SAR ADCs are known for their high speed and moderate resolution, making them suitable for a wide range of data acquisition systems. In the hierarchy of signal processing, the ADC sits between the analog sensor/amplifier and the digital processor, serving as the critical bridge that enables digital systems to interpret real-world analog signals. Key features of the AD571SD/883B include a 10-bit resolution, a maximum conversion time of 25 microseconds, and a parallel digital interface for easy connection to microprocessors and digital logic. The device operates from dual supplies of +5 V and -12 V or -15 V, and includes an internal clock and reference, eliminating the need for external components. The military-grade screening (883B) ensures compliance with MIL-STD-883, providing enhanced reliability for demanding environments. Technically, the AD571SD/883B employs a laser-trimmed thin-film resistor network and a high-speed comparator to achieve its accuracy. The device features a full-scale calibration capability, allowing users to adjust the gain and offset for precise measurements. The bipolar offset and unipolar offset pins provide flexibility in configuring the input range, while the differential nonlinearity is guaranteed to be within ±1 LSB over the entire temperature range. Typical applications include military avionics, radar systems, industrial process control, and high-reliability data acquisition systems. The device's wide operating temperature range and hermetic ceramic package make it ideal for harsh environments where standard commercial ADCs would fail. When designing with the AD571SD/883B, ensure that the analog input is properly buffered and that the power supplies are well-decoupled to minimize noise. The internal reference is trimmed at the factory, but external calibration may be required for absolute accuracy in critical applications.

询价 联系我们
AD573SD - 10-Bit 20 us SAR ADC, 20-CDIP | Analog Devices
AD573SD

AD573SD - 10-Bit 20 us SAR ADC, 20-CDIP | Analog Devices

The Analog Devices AD573SD is a complete 10-bit successive-approximation analog-to-digital converter with a typical conversion time of 20 us, one analog input, and a 20-pin ceramic DIP package. It integrates a DAC, voltage reference, clock, comparator, successive-approximation register, and three-state output buffers. According to the manufacturer data, no external components are required to perform a full-accuracy 10-bit conversion. Performance is guaranteed with +5 V and -12 V or -15 V supplies. The AD573SD uses a 20-CDIP package, while the AD573 family also includes other package configurations, so package and temperature-grade details must be checked when comparing variants. An ADC converts an analog input voltage into a digital code for measurement, control, instrumentation, and industrial signal-processing systems. The AD573 belongs to the SAR ADC family: a successive-approximation register controls an internal DAC while a comparator tests successive bit decisions. SAR converters are useful when a compact, deterministic conversion process and direct digital output are preferred over continuous delta-sigma modulation. The integrated reference, clock, comparator, and output buffers reduce external circuitry and simplify system implementation. The main verified features include 10-bit resolution, no missing codes over temperature, full or 16-bit microprocessor bus-interface capability, fast successive-approximation conversion with 20 us typical timing, operation from +5 V and -15 V supplies, and monolithic construction. The integrated design can reduce board area and assembly complexity. The parallel three-state outputs are useful when the ADC must share a processor data bus or interface directly with digital control logic. The AD573SD is suitable for industrial process measurement, data acquisition, instrumentation, test equipment, and legacy control systems requiring a deterministic parallel ADC. A 20-CDIP package provides through-hole mechanical compatibility for systems designed around ceramic DIP footprints, but it is not interchangeable with a surface-mount package without a PCB change. Supply arrangement, signal conditioning, grounding, and digital-bus timing remain important design considerations. For a new design, use the AD573SD when its 10-bit SAR architecture, integrated functions, parallel interface, and 20-CDIP footprint are specifically required. For higher resolution, different supply architecture, or surface-mount assembly, select a newer ADC whose electrical and pin requirements have been verified. This product page synthesizes verified manufacturer and distributor information, application guidance, and compatibility cautions; missing electrical values are explicitly marked rather than estimated.

询价 联系我们