集成电路

子分类

📁 ADC/DAC 3,100+ 产品 📁 放大器IC 1,900+ 产品 📁 音频编解码器 18 产品 📁 音频IC 2 产品 📁 时钟与计时 660+ 产品 📁 Comparator ICs 1 产品 📁 DSP 1,100+ 产品 📁 数据采集IC 2 产品 📁 数字电位器 4 产品 📁 显示驱动与控制器 1 产品 📁 FPGA与CPLD 7,300+ 产品 📁 接口IC 3,300+ 产品 📁 LED驱动器 1 产品 📁 逻辑IC 460+ 产品 📁 存储IC 870+ 产品 📁 微控制器 20,000+ 产品 📁 微处理器 4 产品 📁 电机驱动器 1 产品 📁 其他 1 产品 📁 Sensor and Detector Interfaces 1 产品 📁 专用IC 15 产品 📁 视频IC 14 产品

产品（39,000+)

PI7C9X760BBLE - I2C/SPI to UART Bridge | Diodes Incorporated
PI7C9X760BBLE

PI7C9X760BBLE - I2C/SPI to UART Bridge | Diodes Incorporated

Diodes Incorporated PI7C9X760BBLE is an integrated interface controller that bridges I2C/SPI serial interfaces with a UART interface. The device is identified as a serial communication controller with 16 terminals and is offered in a TSSOP package. Its primary function is to provide a protocol-conversion path between a host serial bus and UART-based peripheral equipment, allowing embedded systems to connect otherwise incompatible serial interfaces without implementing the complete conversion in host firmware. The PI7C9X760BBLE belongs to the interface-controller product class. Interface ICs sit within the broader integrated-circuit hierarchy and provide the hardware boundary between processors, sensors, transceivers, and communication equipment. A bridge such as this device is useful when a system already uses I2C or SPI on one side but requires a UART interface for a module, debugger, display, sensor, or communication peripheral on the other side. Diodes Incorporated describes the PI7C9X760BBLE as an I2C/SPI-to-UART bridge controller. The related PI7C9X760BBLEX listing identifies the same device family in a 16-TSSOP package, while the related PI7C9X760BCLE listing identifies a TSSOP-16 variant. The verified component information confirms the controller function, industrial temperature grade, gull-wing terminal form, 16 terminals, and TSSOP package code. Detailed electrical timing, supply-voltage, and current-limit values require confirmation from the manufacturer datasheet before final circuit release. Typical uses include industrial instrumentation, embedded control boards, test equipment, and communication adapters where a processor bus must connect to a UART peripheral. Because the bridge is intended for serial protocol translation, the host interface, UART logic levels, baud-rate behavior, and electrical standards should be checked against the specific system requirements. The 16-TSSOP format is suitable for compact surface-mount assemblies but requires careful layout around the fine-pitch leads and adequate soldering clearance. Design work should begin with the manufacturer datasheet, including the pin-description table, recommended operating conditions, timing diagrams, and application circuit. The exact pin assignments cannot be reproduced from the product listings alone. Confirm the device's supply requirements, interface voltage levels, reset or enable behavior, and supported baud-rate range before selecting decoupling, pull-up, and level-shifting components. This page provides practical engineering context for the PI7C9X760BBLE, including its bridge role, package identity, sourcing links, and the key design checks that should be completed before PCB release.

询价 联系我们
PI7C9X760BCLE - 33Mbps I2C/SPI to UART Bridge | Diodes
PI7C9X760BCLE

PI7C9X760BCLE - 33Mbps I2C/SPI to UART Bridge | Diodes

Diodes Incorporated PI7C9X760BCLE is an I2C-bus and SPI to single-channel UART bridge controller rated for data rates up to 33 Mbps, with support for up to eight additional programmable GPIO pins and a 16-pin TSSOP package. The device combines two serial host-side interfaces with one high-performance UART channel, making it suitable for embedded systems that need to translate between peripheral buses and a conventional UART endpoint. An I2C/SPI-to-UART bridge is an interface-controller IC that allows a host processor or another digital subsystem to communicate with a UART peripheral through a serial bus that the host already supports. In the electronic-component hierarchy, the PI7C9X760 belongs to interface controllers, interface ICs, and integrated circuits. This bridge architecture can reduce peripheral connection requirements in handheld, battery-operated, embedded, and cost-sensitive equipment. Key features include support for both I2C and SPI host-side buses, one high-performance UART channel, operation at data rates up to 33 Mbps, and low operating and sleeping current. The manufacturer identifies up to eight programmable GPIO pins as an additional expansion capability. These features make the controller useful when a design must expose legacy UART equipment through a compact serial interface while retaining peripheral control connections. The PI7C9X760BCLE is supplied in a 16-pin TSSOP package. Its small surface-mount format supports compact assemblies, while the tube packaging identified for this ordering code is intended for production handling through automated assembly equipment. Because the bridge is intended for space-constrained equipment, careful attention to interface levels, signal routing, clocking, and supply decoupling remains important during PCB implementation. Typical applications include industrial serial gateways, handheld test and measurement equipment, battery-powered data loggers, embedded control systems, serial protocol adapters, and embedded service interfaces. In each case, the bridge can provide a defined path between I2C or SPI system buses and UART-compatible downstream equipment. Selection should include checking protocol support, baud-rate requirements, logic thresholds, pin mapping, and package compatibility against the host platform. Design the PCB with short, continuous signal paths and place decoupling capacitance close to the device supply pins. Confirm the exact electrical limits, configuration method, clock requirements, and UART signaling details in the manufacturer datasheet before schematic release. The use of a known package footprint alone does not establish complete functional equivalence when replacing an existing bridge. This product page combines the manufacturer's PI7C9X760 architecture information with package, ordering, sourcing, and practical interface-design guidance. It also distinguishes documented drop-in replacements from general cross-reference tools, helping engineers evaluate compatibility before committing to a board revision.

询价 联系我们
PI7C9X760BZDE - 33Mbps I2C/SPI to UART Bridge | Diodes
PI7C9X760BZDE

PI7C9X760BZDE - 33Mbps I2C/SPI to UART Bridge | Diodes

Diodes Incorporated PI7C9X760BZDE is an I2C-bus/SPI to single-channel high-performance UART bridge controller designed for compact embedded systems. It supports data rates up to 33 Mbps, provides 64-byte transmit and receive FIFOs, and offers eight additional programmable general-purpose I/O pins. The device operates from 1.8 V, 2.5 V, or 3.3 V supply rails and is offered in a 24-pin TQFN package measuring 4 mm by 4 mm. An I2C/SPI-to-UART bridge is an interface controller that translates data between a synchronous serial bus and an asynchronous UART channel. Within the broader semiconductor hierarchy, it belongs to the bridge-controller and interface-controller family, where it connects a microcontroller or processor to an external UART endpoint. This protocol conversion allows a host with I2C or SPI connectivity to communicate with UART peripherals without implementing each side of the serial interface in host firmware. The PI7C9X760 family supports operating and sleeping current optimized for cost-efficient, handheld, and battery-operated equipment. Its maximum data rate of 33 Mbps supports high-speed serial links, while the 64-byte TX and RX FIFOs help decouple host-bus transactions from UART timing. Eight programmable GPIO pins add flexible auxiliary digital signals without requiring another small controller. The available supply-voltage options also allow the device to fit common 1.8 V, 2.5 V, and 3.3 V embedded power systems. The PI7C9X760 uses an I2C-bus or SPI host interface on one side and a single UART channel on the other. This architecture is useful when a system already exposes a host-side serial bus but needs a conventional asynchronous serial port for a modem, sensor, display, or other peripheral. The FIFO depth improves handling of short bursts, although the host must still configure baud rate, framing, parity, flow control, and protocol-specific behavior through the device registers. Typical uses include battery-powered data collection, compact industrial modules, serial-port adapters, handheld test equipment, and embedded accessories that require an I2C or SPI master interface alongside one UART channel. The 24-TQFN 4 mm by 4 mm package helps reduce board area in space-constrained designs. The exposed thermal pad assists heat transfer, but correct layout and exposed-pad soldering remain essential for reliable thermal and electrical performance. Designers should follow the PI7C9X760 manufacturer datasheet for the complete pin description, recommended decoupling, register map, clock requirements, electrical limits, and exposed-pad layout. Confirm the target UART baud rate, host-bus voltage, GPIO use, and power budget before PCB release. The 33 Mbps maximum data rate should not be interpreted as an unrestricted system-throughput guarantee because host-bus overhead and UART framing affect effective payload throughput. This product page consolidates the verified manufacturer and distributor facts for the PI7C9X760BZDE, including protocol capability, data rate, FIFO capacity, GPIO resources, supply options, package format, sourcing information, and design-oriented selection guidance. Use the linked manufacturer datasheet as the controlling document for implementation details and production releases.

询价 联系我们
PI7C9X762BLE - Dual UART Bridge Controller | Diodes Incorporated
PI7C9X762BLE

PI7C9X762BLE - Dual UART Bridge Controller | Diodes Incorporated

Diodes Incorporated PI7C9X762BLE is an I2C-bus/SPI to dual-channel UART bridge controller supporting data rates up to 33 Mbps, 64-byte transmit and receive buffers, and as many as eight programmable GPIO pins in a 28-TSSOP package. It operates from 1.8 V, 2.5 V, or 3.3 V supply rails, making it suitable for compact embedded and handheld systems. An interface bridge or protocol converter is an interface IC that translates commands and data between digital communication protocols. The PI7C9X762 belongs to the UART interface family and connects an I2C-bus or SPI controller with two UART channels. This hierarchy places it within interface controllers and, more broadly, within digital semiconductors and embedded communication systems. The controller combines a dual-channel UART architecture with I2C/SPI host-side connectivity. Its headline capabilities include two UART channels, operation to 33 Mbps, 64-byte TX/RX buffering, and up to eight additional programmable GPIO pins. Low operating and sleeping current are emphasized by the manufacturer, supporting cost-efficient, battery-operated equipment where serial conversion must consume limited board area. The PI7C9X762 register set is backward-compatible with the widely used 16C450 UART, according to the manufacturer datasheet. Additional functions include automatic hardware and software flow control, automatic RS-485 support, fractional baud-rate support, and software reset. The software-reset capability allows firmware to reset the UART independently of the hardware reset signal, which can simplify recovery after a communication fault. Typical uses include portable data-collection equipment, industrial serial gateways, handheld test instruments, and embedded systems that must expose two high-speed UART channels through a host-controlled I2C or SPI interface. The dual-channel architecture reduces the need for separate UART devices, while the 28-TSSOP package supports conventional surface-mount PCB assembly. Designers should verify the complete pin map, register behavior, electrical limits, and timing margins against the PI7C9X762 datasheet before layout release. Particular attention should be paid to I2C pull-up placement, SPI signal integrity, UART baud-rate accuracy, RS-485 direction control, and supply sequencing across the 1.8 V, 2.5 V, and 3.3 V operating options. This product record combines the verified manufacturer specifications, distributor identification, package data, protocol capabilities, and sourcing links in one engineering-oriented reference. It also distinguishes confirmed device attributes from data that must be obtained from the full datasheet or authorized distributor records before a production design is released.

询价 联系我们
PI7C9X762BLEX - I2C/SPI to 2-Channel UART Bridge | Diodes
PI7C9X762BLEX

PI7C9X762BLEX - I2C/SPI to 2-Channel UART Bridge | Diodes

Diodes Incorporated PI7C9X762BLEX is an I2C/SPI-to-UART bridge controller that converts a synchronous serial interface into two independent UART channels. The device is packaged in a 28-pin TSSOP and is specified as a standard 3000-piece package. It is designed for embedded systems where a microcontroller needs to add legacy UART ports without consuming additional host I2C or SPI pins. An I2C/SPI-to-UART bridge is a serial interface controller within the broader UART interface IC and interface-controller hierarchy. It sits between a host processor and one or more asynchronous serial peripherals. The host communicates through I2C or SPI, while the bridge manages framing, baud-rate configuration, data transfer, and status reporting for the UART side. This approach reduces host pin count and centralizes protocol conversion in a dedicated device. The PI7C9X762BLEX provides two UART channels and supports both I2C and SPI host-side operation. Its 28-pin TSSOP package suits compact industrial and embedded control assemblies where surface-mount construction is required. The manufacturer identifies the device as an I2C/SPI-to-2-channel UART bridge with a 3,000-unit standard package quantity. The architecture separates the synchronous host interface from the asynchronous UART channels, allowing one host controller to service multiple serial devices. Each UART path can function as a communications endpoint for sensors, modems, test equipment, or industrial peripherals. I2C operation is useful when several low-to-medium-rate devices share a wired bus, while SPI provides a dedicated, higher-rate host connection for point-to-point embedded links. Typical uses include automotive infotainment interfaces, industrial instrumentation, communications modules, and embedded controllers that need legacy serial ports. The device is also appropriate for prototype and production systems that need a compact protocol-conversion stage between an SPI-capable controller and two UART peripherals. Designers should confirm the host-side logic levels, supported baud-rate range, parity format, flow-control method, and interrupt behavior against the manufacturer datasheet before layout. Because two UART channels share one host interface, firmware must also avoid simultaneous transactions that exceed the bridge's command and status-handling capacity.

询价 联系我们
PI7C9X762BZHE - I2C/SPI to Dual UART Bridge | Diodes Incorporated
PI7C9X762BZHE

PI7C9X762BZHE - I2C/SPI to Dual UART Bridge | Diodes Incorporated

The Diodes Incorporated PI7C9X762BZHE is an I2C-bus and SPI to dual-channel UART bridge controller with a 32-pin TQFN package measuring 5 mm by 5 mm. It supports I2C and SPI host-side communication on one side and two UART channels on the other, making it suitable for embedded systems that need to connect serial peripherals, sensors, or modules to a processor with a different serial protocol. An interface bridge is a semiconductor device that translates commands and data between incompatible communication protocols while presenting a defined electrical interface to the host system. In this case, the PI7C9X762 family belongs to the interface IC hierarchy and bridges I2C or SPI buses to dual UART ports. The manufacturer describes the controller as a high-performance bridge with data rates up to 33 Mbps and low operating and sleeping current. The PI7C9X762BZHE includes support for up to eight additional programmable general-purpose I/O pins, expanding its usefulness in compact embedded products where connector count and board area are constrained. The device can operate from 1.8 V, 2.5 V, or 3.3 V supply rails, allowing integration into low-voltage portable and battery-operated equipment. Its dual-UART architecture can also reduce the number of separate protocol-conversion components required in a system. Typical applications include industrial control modules, handheld test equipment, battery-powered instruments, communications equipment, and embedded systems that expose an I2C or SPI peripheral through conventional UART connections. The small 32-TQFN package supports compact layouts, but its exposed pad and high-speed serial interfaces require careful PCB planning. Power, ground, and signal-return paths should be arranged to minimize switching noise and data errors. When selecting this controller, verify the electrical levels, protocol timing, UART baud-rate requirements, GPIO usage, and package pin assignment against the manufacturer datasheet. The exact PI7C9X762BZHE ordering code determines the lead-free package, temperature, and production configuration, so related family members should not be substituted without checking their suffix codes and pin definitions. This product page consolidates the manufacturer function description, package information, interface characteristics, application guidance, and verified sourcing information into a technical reference for engineers evaluating the PI7C9X762BZHE.

询价 联系我们
PI7C9X762CLE - 33Mbps Dual UART Bridge | Diodes
PI7C9X762CLE

PI7C9X762CLE - 33Mbps Dual UART Bridge | Diodes

Diodes Incorporated PI7C9X762CLE is a dual-channel high-performance UART bridge controller that connects I2C-bus or SPI serial interfaces to two UART channels. The device supports data rates up to 33 Mbps, includes up to eight additional programmable general-purpose I/O pins, and is supplied in the compact 28-pin TSSOP package. It is intended for cost-efficient embedded systems where an existing serial processor must communicate through one or more UART peripherals. An I2C/SPI-to-UART bridge is an interface controller within the broader interface IC category. I2C and SPI use clocked, host-oriented buses, while UART provides independent asynchronous serial channels. A bridge controller allows a host processor to configure, monitor, and exchange data with UART-connected sensors, displays, modems, or industrial equipment without implementing every low-level protocol conversion in host firmware. The PI7C9X762 therefore belongs to the serial-interface-controller and embedded communication-controller hierarchy. The PI7C9X762 family provides dual-channel UART bridging, operation up to 33 Mbps, and as many as eight programmable GPIO pins. According to the Diodes Incorporated product page, the controller is designed around low operating and sleeping current, making it suitable for compact, cost-sensitive equipment. Its small TSSOP-28 package also supports space-constrained PCB layouts where a larger bridge or discrete level-shifting circuitry would be inconvenient. The manufacturer describes the PI7C9X762 as an I2C-bus/SPI to dual-channel high-performance UART bridge controller. This architecture allows the host-side I2C or SPI connection to coexist with two UART channels in one package. The exact electrical limits, register map, operating-voltage range, and pin-level signal assignments are not included in the supplied verified excerpts, so engineers should consult the manufacturer datasheet before finalizing a board or power design. Typical uses include industrial data acquisition, handheld test equipment, programmable serial adapters, embedded control panels, and battery-operated instruments. In these systems, the bridge can manage UART traffic while the host processor communicates through I2C or SPI. The dual-channel architecture may reduce external UART component count, while the maximum stated data rate of 33 Mbps supports communication well above common low-speed serial-console rates. Design planning should account for protocol-specific level translation, signal integrity, device configuration, and firmware ownership of the bridge registers. The manufacturer indicates low operating and sleeping current, but the supplied data does not publish exact current values. Confirm supply voltage, absolute maximum ratings, UART logic levels, reset requirements, and all 28 pin assignments in the official datasheet before production release. This product record combines the manufacturer description with verified distributor pricing, package, and order information. It also distinguishes verified PI7C9X762CLE availability from related ordering codes and unverified substitutes, helping engineers make sourcing and design decisions without relying on incomplete cross-reference listings.

询价 联系我们
PI7C9X762CLEX - I2C/SPI to UART Bridge | Diodes Incorporated
PI7C9X762CLEX

PI7C9X762CLEX - I2C/SPI to UART Bridge | Diodes Incorporated

The Diodes Incorporated PI7C9X762CLEX is an I2C bridge controller with I2C/SPI-to-UART interface conversion, housed in a 28-pin TSSOP package. The device is identified as a UART interface IC and SPI bridge, providing a serial-protocol conversion function for embedded systems. Its 28-TSSOP package supports compact PCB integration, while the ordering suffix X identifies the tape-and-reel configuration listed for a standard quantity of 3,000 units. An I2C bridge controller is an interface IC that connects serial protocols whose electrical and transaction formats differ. In this case, the PI7C9X762CLEX is positioned as an I2C/SPI-to-UART bridge rather than a general-purpose microcontroller or standalone UART transceiver. Such devices are useful when one subsystem communicates through I2C or SPI while another expects serial UART traffic, helping designers avoid implementing a complex protocol-conversion layer in host firmware. The principal verified features are the combined I2C/SPI-to-UART function, UART interface classification, and 28-pin TSSOP package. The PI7C9X762CLEX is available in a tape-and-reel production format, and the manufacturer part-number listing confirms it as the X ordering variant. Detailed operating voltage, clock limits, UART data-rate range, I2C rates, SPI rates, and logic-level specifications require confirmation in the manufacturer datasheet before a circuit is finalized. Protocol-bridge designs normally depend on consistent command formats, electrical levels, timing margins, and deterministic reset behavior. The PI7C9X762CLEX should therefore be evaluated as part of a complete host-to-target interface chain rather than only by its bridge description. Designers should confirm which side of the device is intended to originate transactions, how register access is implemented across each supported protocol, and whether the available serial rates satisfy the latency and bandwidth needs of the target equipment. Typical uses include industrial control modules, serial protocol adapters, embedded instrumentation, automated test equipment, and communication subsystems that need I2C or SPI connectivity presented through a UART-oriented controller interface. It may also be used in legacy equipment where an established UART backbone must accommodate a modern serial peripheral without changing the external connector architecture. Before layout, verify the complete pin assignment, power rails, ground requirements, and decoupling recommendations in the manufacturer datasheet. Keep high-speed or exposed serial traces short, provide a continuous ground reference, and follow the device's recommended input and output arrangements. Confirm logic thresholds against every connected host before committing the PCB layout. This page consolidates the exact ordering information, package and packaging facts, protocol-interface identity, sourcing details, pin-compatible ordering option, and application guidance for PI7C9X762CLEX. It also highlights the parameter fields that engineers should verify in the manufacturer datasheet, helping accelerate component selection and design review.

询价 联系我们
PI7C9X762CZHE - SPI-UART Bridge | Diodes Incorporated
PI7C9X762CZHE

PI7C9X762CZHE - SPI-UART Bridge | Diodes Incorporated

Diodes Incorporated PI7C9X762CZHE is a UART interface controller and SPI-to-UART bridge with support for I2C-to-UART operation, supplied in a 32-lead TQFN surface-mount package measuring 5 mm by 5 mm. The device provides a register-compatible interface with the widely used 16C450 UART, allowing legacy serial-control software to be adapted without redesigning the complete host-driver structure. A UART bridge is an interface integrated circuit that translates a parallel or synchronous host-bus transaction into serial data using a standard UART framing format. The PI7C9X762 belongs to the broader UART controller, interface IC, serial-communication semiconductor, and embedded-interface hierarchy. It is intended for systems in which a host processor needs to reach UART-based peripherals while using a synchronous serial connection on the host side. The PI7C9X762 adds automatic hardware and software flow control to its 16C450-compatible register set. It also provides automatic RS-485 support, fractional baud-rate generation, and software reset. Fractional baud-rate support allows the interface to represent baud rates that are not exact integer multiples of a conventional base clock. Software reset permits the UART to be reinitialized independently of the hardware reset signal, improving recovery after configuration errors or peripheral communication failures. The serial architecture combines an SPI or I2C host-side transaction mechanism with UART transmit and receive functions. Internal registers organize baud-rate generation, modem-control signals, interrupt identification, flow-control status, and buffer management. This arrangement allows embedded systems to connect a processor using a compact synchronous bus to an external UART peripheral without implementing a complete UART state machine in programmable logic or software. Typical uses include industrial serial adapters, test and measurement equipment, embedded control panels, point-of-sale terminals, printers, scanners, and RS-485 equipment. The automatic RS-485 feature can simplify designs that require driver-enable behavior, while automatic flow control helps prevent transmitter overrun when a connected device cannot accept data at the selected baud rate. Board design should preserve the exact pin assignments, power-supply requirements, and recommended decoupling specified in the manufacturer datasheet. Because the package exposes both synchronous host-side signals and UART signals, careless routing near high-current outputs or long external lines can introduce noise or ringing. The SPI or I2C traces should be kept compact, while external UART and RS-485 routes require suitable termination and protection according to the connected cable and interface environment. This product page consolidates the identified PI7C9X762CZHE package information, supported bridge functions, UART compatibility, comparison details, and practical interface-design guidance. It also distinguishes the directly documented same-package family alternative from unverified substitutes so engineers can make a PCB-compatible sourcing decision without treating generic cross-reference results as guaranteed drop-ins.

询价 联系我们
PI7C9X794FCE - Quad UART with 64-Byte FIFO | Diodes Incorporated
PI7C9X794FCE

PI7C9X794FCE - Quad UART with 64-Byte FIFO | Diodes Incorporated

Diodes Incorporated PI7C9X794FCE is a four-channel UART interface controller with a 64-byte FIFO, operating from 1.62 V to 3.6 V and packaged in a 64-LQFP measuring 10 mm by 10 mm. The device integrates RS485 controller and IrDA 1.1 functions, providing a compact interface solution for systems that need multiple serial channels, buffered data transfer, and industrial or infrared connectivity. A UART, or universal asynchronous receiver/transmitter, is a serial communication controller that converts parallel data into framed serial signals and reconstructs received data. The PI7C9X794FCE belongs to the UART interface IC and RS485 controller hierarchy within the broader interface IC and semiconductor categories. Its four channels can reduce the number of external serial controllers required in embedded, industrial, networking, and data-acquisition equipment. Key features include four UART channels, a 64-byte FIFO, an RS485 controller, IrDA 1.1 support, and a 1.62 V to 3.6 V operating-voltage range. The 64-byte FIFO supports buffering between the host interface and serial transmitter or receiver, helping accommodate bursts of incoming or outgoing data without requiring an external FIFO memory. Its 64-LQFP package provides a conventional surface-mount integration option for compact controller boards. The part is presented by DigiKey as an RS485 controller, IrDA 1.1, UART interface with a 64-LQFP package, while Mouser describes it as a quad UART with a 64-byte FIFO. These descriptions place it between a general-purpose multi-channel UART and a dedicated serial transceiver: the on-chip interface manages channel and FIFO functions, while an external line driver or receiver may still be required for physical RS485 or IrDA links. Typical uses include industrial serial concentrators, programmable logic controllers, embedded data loggers, infrared data-transfer equipment, and multiport service interfaces. The four-channel architecture is especially useful where a central processor must exchange data with several peripherals while avoiding one separate UART controller per port. System designers should still verify signal levels, transceiver requirements, timing, and pin-level functions against the manufacturer documentation before layout release. For reliable implementation, place the controller close to its supported peripherals, provide the decoupling and clock circuitry required by the datasheet, and keep long external transmission lines away from sensitive digital nodes. The operating range of 1.62 V to 3.6 V allows integration with 1.8 V and 3.3 V systems, but input levels, output levels, and attached transceivers must remain electrically compatible. Availability, detailed pin assignments, throughput, and electrical limits not shown in the supplied verified results should be checked against the current manufacturer datasheet.

询价 联系我们
PI7C9X794FCEX - Quad UART Interface IC | Diodes Incorporated
PI7C9X794FCEX

PI7C9X794FCEX - Quad UART Interface IC | Diodes Incorporated

Diodes Incorporated PI7C9X794FCEX is a quad UART interface IC operating from 1.62 V to 3.6 V, with four UART channels and a 64-byte FIFO, packaged in a 64-pin LQFP measuring 10 mm by 10 mm. The device is identified as an RS485 controller with IrDA 1.1 support, making it suitable for embedded systems that require multiple serial communication paths. A UART, or universal asynchronous receiver/transmitter, is an interface controller that converts parallel data from a processor into serial data and converts incoming serial data into parallel data for host processing. UART interface ICs sit within the broader category of interface ICs and provide protocol timing, buffering, framing, and status handling for serial links. The PI7C9X794FCEX combines four such channels with a compact surface-mount package. The principal feature of the PI7C9X794FCEX is its four-channel UART architecture. Each channel benefits from dedicated transmit and receive buffering, while the documented 64-byte FIFO supports burst-oriented host traffic and helps separate the processor from individual byte transfers. Its 1.62 V to 3.6 V operating range covers common low-voltage embedded and communications systems while allowing operation from both 1.8 V and 3.3 V supply environments. The RS485 controller and IrDA 1.1 designation broadens the device beyond a basic UART. An RS485-capable channel can support differential industrial serial links when used with suitable external transceiver circuitry, while IrDA-compatible operation addresses short-range infrared data-transfer systems. These functions place the IC between a host processor and physical-layer interface circuits, with the exact line-driver requirements determined by the selected external components. Typical uses include industrial control boards, multiport serial concentrators, embedded test equipment, data-acquisition systems, and communication peripherals requiring several independent UART channels. The four-channel organization can reduce the number of discrete interface devices and simplify firmware multiplexing. Designers should still allocate pins for interrupt, modem-control, and interface-specific signals according to the manufacturer pin-description table. Thermal and layout planning are important in dense designs. Place the device away from heat sources, provide a continuous ground plane, and route high-speed or externally exposed communication signals with appropriate return paths. Decoupling capacitors should be positioned close to the corresponding supply and ground pins according to the manufacturer layout recommendations. This product page consolidates the confirmed electrical, interface, package, and ordering characteristics into an engineering-focused reference. It also distinguishes verified pin-compatible substitutions from broader functional alternatives, helping designers assess replacement risk without assuming that every similarly described UART interface shares the same footprint.

询价 联系我们
PI7C9X7954BFDE - PCIe Quad UART Bridge 128-LQFP | Diodes Inc
PI7C9X7954BFDE

PI7C9X7954BFDE - PCIe Quad UART Bridge 128-LQFP | Diodes Inc

The Diodes Incorporated PI7C9X7954BFDE is a PCI Express to Quad UART (Universal Asynchronous Receiver-Transmitter) I/O bridge delivered in a 128-pin LQFP (14x14 mm) package. It integrates a PCIe Gen1 x1 upstream link with four 16550-compatible UART channels, each with a 128-byte FIFO, and operates from 1.8V and 3.3V supply rails. A PCIe-to-UART bridge is a serial interface controller that converts a PCI Express bus transaction into legacy-style asynchronous serial communication. In the system hierarchy, it sits between the interface controller family and the broader categories of communication ICs and bridge ICs, allowing modern PCIe-only CPU platforms to retain multi-channel RS-232/RS-485 serial ports without a legacy PCI bus. Key features include four independent UART channels, 128-byte transmit and receive FIFOs per channel for reduced CPU interrupt overhead, a PCI Express x1 upstream interface, and dual 1.8V core / 3.3V I/O operation. The lead-free (Pb-free) construction and reduced 14x14 mm package size address modern system requirements for high performance and compact PCB footprints. Architecturally, the device bridges PCIe configuration and memory-mapped transactions to the internal UART register set, maintaining 16550 register compatibility so standard OS serial drivers can operate the ports. The deep FIFOs decouple bursty processor access from slower serial line rates, improving throughput in multi-port systems. Typical applications include remote access servers, industrial automation and process control, instrumentation, point-of-sale (POS) terminals, ATMs, and multi-port RS-232 cards. Design consideration: verify the PCIe reference clock and reset sequencing against the manufacturer datasheet, and provide adequate decoupling on both 1.8V and 3.3V rails. This page synthesizes distributor pricing context, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PI7C9X7954BFDE-MOXA - PCIe Quad UART Bridge | Diodes
PI7C9X7954BFDE-MOXA

PI7C9X7954BFDE-MOXA - PCIe Quad UART Bridge | Diodes

The Diodes Incorporated PI7C9X7954BFDE-MOXA is a PCI Express to Quad UART (Universal Asynchronous Receiver-Transmitter) I/O bridge that integrates four 16C550-compatible UART channels behind a PCIe x1 interface, housed in a 128-pin LQFP (14x14 mm) package. It is manufactured lead (Pb)-free and is the customer-specific variant built for MOXA, a serial-device and industrial networking vendor. A UART bridge is a type of serial interface controller that sits in the broader hierarchy of interface ICs: UART -> serial controller -> I/O bridge IC -> PCI Express peripheral device. Its role in a system is to translate the high-speed, packet-based PCIe bus into multiple legacy asynchronous serial ports, allowing modern PCIe-only host platforms to drive RS-232, RS-422, and RS-485 links that would otherwise require PCI or cardbus legacy slots. Key features include four independent UART channels that are fully software compatible with 16C550-type device drivers, meaning standard operating-system serial drivers work without vendor-specific code. The device supports configurable RS-232, RS-422, and RS-485 operating modes, an EEPROM interface for storing configuration data, and hardware pin straps that pre-program selected registers to simplify system initialization. The PCIe x1 upstream link targets high-performance, reduced-footprint designs. From an architecture standpoint, the PI7C9X7954 buffers and arbitrates serial traffic across its four channels, with each UART providing transmit and receive FIFOs in the 16C550 tradition to reduce CPU interrupt overhead. Register-level compatibility means BIOS, Windows, Linux, and embedded RTOS serial stacks enumerate the device as a standard multi-port serial controller. Typical applications include remote access servers, factory automation and process control equipment, instrumentation, POS terminals, ATMs, and multi-port RS-232 cards - precisely the markets MOXA serves with serial device servers and multi-port communication boards. Design consideration: verify serial signaling levels externally - the bridge provides logic-level UART signals, so RS-232 transceivers or RS-485 drivers must be added per port; budget them into the BOM and layout. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PI7C9X7954BFDEX - PCIe x1 to 4-Port UART Bridge | Diodes Inc.
PI7C9X7954BFDEX

PI7C9X7954BFDEX - PCIe x1 to 4-Port UART Bridge | Diodes Inc.

The Diodes Incorporated PI7C9X7954BFDEX is a PCI Express x1 to quad UART bridge controller that adds four high-speed 16550-compatible serial ports through a single PCIe lane, housed in a 128-pin LQFP (14x14 mm) package. It integrates a PCIe endpoint function, a serial-port controller block, and four industry-standard UARTs, allowing legacy COM-port devices such as POS peripherals, industrial terminals, and medical instruments to connect to modern PCIe-only host platforms. A UART (universal asynchronous receiver-transmitter) is a serial interface block that converts parallel bus data into asynchronous serial data frames. In the interface-IC hierarchy, this device belongs to the bridge-controller class: PCIe on the host side, UART on the device side. Bridges like the PI7C9X7954BFDEX are the standard way to preserve RS-232/RS-485 connectivity on motherboards, backplanes, and add-in cards that no longer expose legacy ISA or PCI slots. Key features include four 16550-compatible UART channels with 64-byte transmit and receive FIFOs for reduced interrupt overhead, a PCIe x1 Gen1 (2.5 GT/s) host interface, support for cardbus/legacy COM-port register mapping, and industrial-grade temperature operation indicated by the EX suffix. Programmable baud-rate generators support standard and extended data rates, and flow-control options include RTS/CTS hardware handshaking and XON/XOFF software flow control. Architecturally, the bridge maps each UART's register set into PCI/PCIe memory or I/O space, presenting four standard COM ports to the operating system without vendor-specific drivers on most platforms. Interrupt handling is consolidated through a single MSI or legacy INTx signal, simplifying host interrupt routing in dense multi-port designs. Typical applications include industrial PCs and embedded controllers requiring multiple serial devices, point-of-sale terminals driving receipt printers and barcode scanners, network-equipment management consoles, and medical instrument serial links. Its LQFP-128 footprint suits both add-in cards and on-board solutions. Design consideration: the 128-LQFP has an 0.4 mm-class pin pitch (per package outline), so verify fab capability and design the PCIe 100 MHz reference clock distribution with clean, low-jitter routing to the host clock source. This page synthesizes distributor pricing, availability, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PI7C9X798ME - 8-Channel UART Bridge | Diodes Incorporated
PI7C9X798ME

PI7C9X798ME - 8-Channel UART Bridge | Diodes Incorporated

Diodes Incorporated PI7C9X798ME is an octal universal asynchronous receiver and transmitter controller, or 8-channel UART bridge, for high-bandwidth communication systems. It operates from 1.62 V to 3.6 V, accepts 5 V-tolerant serial modem inputs, and is offered in a 100-MQFP package measuring 14 mm by 20 mm. The device consolidates eight UART channels and their associated control into one high-integration interface IC. A UART is a serial communication interface that converts parallel data from a processor or controller into a framed serial stream and receives framed serial data in parallel form. Within the interface-controller hierarchy, a multi-channel UART bridge extends the basic UART function across eight channels, allowing one integrated circuit to connect a host system to multiple serial endpoints. This integration can reduce the number of discrete interface devices and simplify control of communications equipment. The PI7C9X798 family's global interrupt source register provides interrupt-status information for all eight channels, helping firmware identify the source of an interrupt more quickly. Its 1.62 V to 3.6 V core supply range supports low-voltage embedded systems, while the 5 V-tolerant serial inputs broaden its usefulness in boards that expose older modem or serial interfaces. The operating architecture is designed around a 16C550-compatible octal UART, as identified by the distributor product listings. Typical uses include industrial serial concentrators, multi-port communications equipment, data acquisition systems, embedded control platforms, and legacy peripheral bridges. In a multi-channel design, the PI7C9X798ME can terminate several serial links while presenting a consolidated device to the host processor. Designers should confirm channel-clocking, interrupt, electrical-interface, and protocol requirements against the complete manufacturer datasheet before releasing a PCB. Layout planning is especially important for a 100-lead MQFP because its fine pitch requires careful escape routing and reliable assembly processes. Input and output interfaces must also satisfy the voltage limits of the target serial links. Although the core operates below 3.6 V, the stated 5 V tolerance applies specifically to the serial modem inputs and should not be generalized to every supply or control pin. This page combines verified distributor pricing, package information, family-level specifications, practical integration considerations, and verified-source links. It also distinguishes confirmed product attributes from electrical details that still require confirmation from the manufacturer datasheet, helping engineers evaluate the PI7C9X798ME without filling missing data with assumptions.

询价 联系我们
PI7C9X9208SLFDE - 8-Ch Video Decoder Bridge | Diodes
PI7C9X9208SLFDE

PI7C9X9208SLFDE - 8-Ch Video Decoder Bridge | Diodes

Diodes Incorporated PI7C9X9208SLFDE is a PCIe eight-channel video and audio decoder bridge with an LQFP package. The verified distributor listings identify the device as an IC for PCIe eight-channel video/audio decoding and describe the package as LQFP; other distributor records identify a 128-LQFP package measuring 14 mm by 14 mm. The available verified data does not provide the complete electrical timing table, operating-voltage range, clock requirements, or pin-level definitions. A video decoder bridge is an interface IC that receives digital video streams and associated audio or control data, converts or routes those streams into a system-facing interface, and helps bridge legacy display or multimedia paths to PCIe-based host systems. In the product hierarchy, this component belongs to video processing and interface ICs, with PCIe connectivity as its host-facing transport. It is intended for systems requiring eight-channel video/audio decoding rather than a general-purpose display controller. The PI7C9X9208SLFDE is specifically associated with PCIe eight-channel video/audio decoder functionality. Its LFDE ordering suffix is supplied exactly as shown by the verified distributor records, while the package evidence identifies a 128-pin LQFP. The supplied sources do not state whether the part is currently active, whether it is obsolete, or whether a particular lifecycle designation applies. It also does not provide verified pricing, stock, lead time, or a complete set of electrical limits. Typical design use is an embedded video system, digital signage controller, video capture appliance, or PCIe expansion card where multiple decoded video/audio channels must be transferred through a PCIe interface. The decoder should be validated against the host PCIe topology, display timing, audio routing, reference clock, and board-level signal-integrity requirements. Because the verified data does not specify those details, engineers should consult the manufacturer datasheet before finalizing clocking, lane configuration, termination, or firmware assumptions. The most important design consideration is to avoid treating distributor search snippets as a substitute for the complete datasheet. In particular, verify the supported input formats, output interface, electrical timing, reset requirements, power rails, package drawing, exposed-pad treatment, and absolute maximum ratings. PCB layout should preserve high-speed signal return paths and provide the required decoupling and grounding according to the complete manufacturer documentation. This page consolidates verified distributor identity, package information, sourcing links, and the available cross-reference context. It intentionally distinguishes confirmed facts from unavailable specifications rather than filling engineering gaps with assumptions.

询价 联系我们
PIC10F200-E/MC - 8-Bit Flash MCU, 384B, 4MHz, 8-DFN | Microchip
PIC10F200-E/MC

PIC10F200-E/MC - 8-Bit Flash MCU, 384B, 4MHz, 8-DFN | Microchip

The Microchip Technology PIC10F200-E/MC is an 8-bit, fully-static, Flash-based CMOS microcontroller in a 6/8-pin DFN (2x3 mm) package with 384 bytes of program Flash, 16 bytes of RAM, and 4 MHz internal oscillator execution. It integrates a RISC core delivering 33 single-word/single-cycle instructions with 12-bit-wide instruction words, achieving typical 2:1 code compression over competing 8-bit MCUs and 1 MIPS performance from a 4 MHz clock. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, program memory, data memory, and I/O peripherals on a single die; in the broader component taxonomy it sits below microprocessors and above simple logic. The PIC10F200 belongs to the baseline PIC10F family from Microchip Technology - the smallest Flash-programmable 8-bit MCU line in the industry. Unlike 32-bit Cortex-M parts, 8-bit MCUs are optimized for deterministic, low-power, low-cost glue logic replacement in cost-sensitive embedded designs. Key features include 4 I/O pins (GPIO), an 8-bit timer (TMR0) with 8-bit prescaler, an integrated 4 MHz internal precision oscillator, a power-on reset (POR) and device reset timer (DRT), and a watchdog timer (WDT) with its own on-chip RC oscillator for reliable operation without external components. The wide operating voltage range of 2.0V to 5.5V and -40C to +125C extended temperature grade support battery-powered and industrial-grade designs. The PIC10F200-E/MC uses a Harvard RISC architecture with separate program and data buses, executed in a single instruction cycle (4 clocks) except for program branches which take two cycles. The Flash memory supports in-circuit serial programming (ICSP) via two pins (GP0/GP1), enabling firmware updates in the field without removing the device. An 8-bit wide instruction word, 12-bit program memory width, and 8-level hardware stack simplify C and assembly development with the MPLAB XC8 toolchain. Typical applications include low-end logic replacement in consumer appliances, PWM LED dimming, fan/thermostat control in HVAC, battery chargers, and sensor signal conditioning. The 8-DFN (MC) package enables surface-mount designs under 6 mm squared - ideal where PCB area is at a premium. The wide VDD range and small footprint make this part popular as a configurable replacement for discrete 555 timer and CMOS logic circuits in production designs. When designing with this MCU, note that only 4 of the 6 functional pins are brought out as GPIO on the 8-DFN package (the SOT-23 6-pin version exposes all 6). Place a 100 nF decoupling capacitor as close to VDD as possible, and consider the in-circuit serial programming (ICSP) pinout when laying out the PCB. The internal 4 MHz oscillator has a factory calibration of +/- 1% typical, eliminating external crystals in most cost-sensitive designs. This page synthesizes distributor pricing, verified drop-in alternatives within the PIC10F family, and practical PCB layout/design notes that complement the manufacturer datasheet and standard distributor listings.

询价 联系我们
PIC10F200-E/P - 8-bit Flash MCU, 384B, 4MHz | Microchip
PIC10F200-E/P

PIC10F200-E/P - 8-bit Flash MCU, 384B, 4MHz | Microchip

The Microchip Technology PIC10F200-E/P is a low-cost, high-performance, 8-bit, fully static, Flash-based CMOS microcontroller. Housed in an 8-pin PDIP (P) through-hole package, it features 384 bytes of Flash program memory (256 x 12 words), 16 bytes of data RAM, and 4 I/O pins, and operates at up to 4 MHz instruction clock. The device is rated for the -40C to +125C extended industrial temperature range (the "E" suffix denotes the extended temperature grade), making it suitable for harsh-environment designs. What is a PIC10F microcontroller? The PIC10F family is Microchip's smallest 8-bit PIC microcontroller line, positioned at the bottom of the 8-bit MCU hierarchy: 8-bit MCU -> microcontroller -> embedded controller -> semiconductor. These parts use a RISC architecture with only 33 single-word, single-cycle instructions, which makes them ideal for cost-sensitive, space-constrained applications where a few pins of digital logic are needed in place of discrete glue logic or small ASICs. The PIC10F200 is the most basic member of the family, deliberately stripped down to the smallest possible memory and pin count to minimize cost. Key features include an internal 4 MHz oscillator (no external crystal required), a 4-channel 8-bit Analog-to-Digital Converter (ADC) on most family members, an 8-bit timer/counter with prescaler, and a watchdog timer with its own on-chip RC oscillator for reliable operation. The Flash program memory supports in-circuit serial programming (ICSP) and in-circuit debugging, enabling rapid prototyping and field firmware updates without removing the part from the board. The PIC10F200 is fabricated in CMOS technology with a wide 2.0V to 5.5V operating voltage range, allowing direct battery operation. Its ultra-low power consumption makes it well-suited for battery-powered and energy-harvesting designs. The device consumes only a few hundred microamps active and supports a sleep mode with nanoamp-level standby current for power-critical applications. Typical applications include LED lighting control, simple sensor signal conditioning, battery chargers, low-end consumer appliances, and replacement of discrete logic in space-constrained boards. The 8-pin PDIP (P) package is favored for prototype and hobbyist work because it accepts standard through-hole tooling and breadboards. When designing with this device, ensure that all unused I/O pins are configured as outputs and tied low (or high, depending on application), because floating inputs can draw excessive supply current and inject noise into adjacent analog pins. The MCLR pin (pin 4) is shared with the programming voltage input and should be pulled up to VDD through a 10 kohm resistor for normal operation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC10F200-I/MC - 8-bit Flash MCU, 384B Flash, 4MHz, 8-DFN | Microchip
PIC10F200-I/MC

PIC10F200-I/MC - 8-bit Flash MCU, 384B Flash, 4MHz, 8-DFN | Microchip

The Microchip PIC10F200-I/MC is a low-cost, high-performance, 8-bit, fully static, Flash-based CMOS microcontroller housed in an 8-pin DFN (2x3 mm) package. It features 384 bytes of Flash program memory (256 x 12 words), 16 bytes of RAM, and 4 MHz internal oscillator across a 2.0V to 5.5V operating range. The device uses a RISC architecture with 33 single-word/single-cycle instructions, giving an order-of-magnitude performance advantage over competing 8-bit microcontrollers in its class. An 8-bit microcontroller (MCU) is a small, self-contained computer-on-a-chip that integrates a CPU, RAM, non-volatile program memory, and I/O peripherals into a single IC. Within the broader taxonomy, the PIC10F200 sits in the lowest-pincount tier of 8-bit microcontrollers, classified as an ultra-small Flash MCU; it is a sub-class of microcontrollers, which in turn belong to microprocessors, which belong to integrated circuits and finally to semiconductors. The PIC10F200 family is designed for applications that need real microcontroller functionality at the cost of a discrete logic IC, replacing 555 timers, op-amp sequencers, and small logic packages with programmable intelligence. Key features of the PIC10F200-I/MC include an internal 4 MHz oscillator, 4-bit digital I/O, one 8-bit timer, a Watchdog Timer with on-chip RC oscillator, in-circuit serial programming (ICSP), and Power-on Reset. The device operates from -40C to +85C industrial temperature range, draws microampere-level supply current, and supports CMOS/TTL-compatible I/O. The 8-DFN (Dual Flat No-lead) package measures only 2 mm x 3 mm, making it one of the smallest microcontrollers in volume production. Typical applications include logic-chip replacement (small glue-logic functions), battery chargers, LED flashers, timer substitutes for 555 circuits, sensor-conditioning front-ends, and ultra-low-cost consumer products such as toys and personal-care devices. Four I/O pins provide enough flexibility for most simple sequencing or PWM-style tasks. When designing with this MCU, note that code execution is single-cycle at 4 MHz, giving 1 us instruction time (branches take 2 cycles). Programming is performed through ICSP using two pins (GP0/GP1), which must be accessible on the PCB. Designers upgrading to PIC10F202/204/206 should verify pinout compatibility carefully, as the larger siblings add features but share the same DFN footprint. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes drawn from the manufacturer datasheet and authorized distributor listings.

询价 联系我们
PIC10F200-I/P - 8-bit 4MHz 384B Flash MCU 8-PDIP | Microchip
PIC10F200-I/P

PIC10F200-I/P - 8-bit 4MHz 384B Flash MCU 8-PDIP | Microchip

The Microchip Technology PIC10F200-I/P is a 6-pin (8-PDIP pinout) 8-bit Flash-based CMOS microcontroller delivering 384 bytes of program memory, 16 bytes of RAM, and 4 I/O pins in an 8-pin PDIP through-hole package. The device executes instructions at 4 MHz from its internal 4 MHz RC oscillator and consumes only a few hundred microamperes in active mode for ultra-low-power embedded applications. The "-I" suffix designates an industrial temperature grade of -40C to +85C, while the "/P" suffix denotes the PDIP-8 package. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash/ROM), data memory (RAM), and programmable I/O peripherals. The PIC10F200 belongs to Microchip's 8-bit PIC10F family - the smallest, lowest-cost microcontrollers in the PIC architecture - designed for logic replacement, simple sequencing, and glue logic applications. It employs a RISC architecture with 33 single-word/single-cycle instructions, giving it code density and deterministic execution that outperforms many 8051-class competitors. Within the broader component taxonomy, the PIC10F200 is a microcontroller -> 8-bit MCU -> embedded controller -> semiconductor IC. Key features include 384 bytes of Flash program memory (256 x 12-bit words), 16 bytes of SRAM data memory, an 8-bit timer/counter, an internal 4 MHz oscillator (no external crystal required), wide operating voltage from 2.0V to 5.5V, in-circuit serial programming (ICSP), and a power-on reset with brown-out detection. The 8-PDIP package allows breadboard-friendly through-hole prototyping, which is unusual in this price-and-size class dominated by SOT-23-style surface-mount parts. The architecture combines a Harvard-style program/data memory split with a 12-bit instruction word, delivering typical 2:1 code compression versus 8-bit CISC alternatives. The internal 4 MHz RC oscillator eliminates external clock components while supporting calibration via the OSCCAL register. The single 8-bit timer (TMR0) with optional watchdog timer supports periodic wakeup and event-timing applications. The device supports in-circuit debugging through ICSP and an ICD interface. Typical applications include logic-replacement in appliances and consumer products, LED sequencing and blinking controllers, simple sensor signal conditioning, battery-powered devices, hardware sequencers, fan controllers, and toy electronics. Its 2.0V-5.5V operating range and sub-mA active current make it suitable for coin-cell and 2xAA battery designs. When designing with this part, mind the limitation of only 4 usable I/O pins (GP0-GP3), since pins 5-8 are shared with VDD, VSS, and ICSP functions. Always reserve one I/O for ICSP programming. The internal oscillator accuracy is typically ±1% after calibration, which may be insufficient for UART timing without software compensation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing an engineer-focused reference for selecting the PIC10F200-I/P across cost-sensitive embedded designs.

询价 联系我们
PIC10F200T-E/OT - 8-bit MCU, 384B Flash, SOT-23-6 | Microchip
PIC10F200T-E/OT

PIC10F200T-E/OT - 8-bit MCU, 384B Flash, SOT-23-6 | Microchip

The Microchip Technology PIC10F200T-E/OT is an 8-bit PIC microcontroller in a 6-pin SOT-23-6 surface-mount package with 384 bytes of Flash program memory, 16 bytes of RAM, and 4 I/O pins operating at 4 MHz from a 2.0V to 5.5V supply. The device is rated for the extended industrial temperature range of -40C to +125C and ships on a 3000-piece tape-and-reel carrier with a suffix code /OT denoting the SOT-23-6 package option. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, working RAM, and programmable I/O peripherals. The PIC10F200 sits at the bottom of the 8-bit PIC family hierarchy - microcontroller -> 8-bit MCU -> PIC10 family -> low-cost Flash MCU - and is engineered for applications where BOM cost, PCB area, and predictable performance outweigh raw throughput. Its RISC architecture executes 33 single-cycle (1 us at 4 MHz) instructions from a 12-bit-wide instruction word, delivering roughly 2:1 code density over competing 8-bit cores. Key features include an internal 4 MHz oscillator with no external components required, three usable I/O pins plus one input-only pin (GP3), an 8-bit timer/counter (TMR0) with watchdog, in-circuit serial programming (ICSP), code protection, and an ultra-low 100 nA sleep current for battery-powered duty-cycled designs. The SOT-23-6 footprint is one of the smallest MCU packages available, enabling direct replacement of discrete 555-timer or logic-gate circuits in space-constrained products. The architecture is built around a Harvard-style CPU with separate program and data buses, eight-level hardware stack, and a single-cycle instruction fetch pipeline. This deterministic execution model simplifies real-time firmware, while the wide 12-bit instructions pack more work into each Flash word - reducing total Flash consumption and enabling the 384-byte program budget to host meaningful control loops. Typical applications include LED blink and chase controllers, battery status indicators, appliance timer replacements for 555 circuits, charger indicator logic, toy sound sequencers, and small-sensor interfaces. The wide 2.0V to 5.5V supply range allows direct connection to single-cell Li-ion, two-cell alkaline, or 5V regulated rails without level translation. Designers should note that only three pins (GP0, GP1, GP2) are bidirectional; GP3 is input-only and pin 1 is reserved for ICSP. A 100 nF decoupling capacitor as close as possible to VDD is mandatory, and unused I/O must be configured as outputs low to minimize sleep current. This page consolidates verified distributor pricing, drop-in compatible SOT-23-6 alternatives, and design notes that go beyond the manufacturer datasheet to help engineers evaluate the PIC10F200T-E/OT quickly.

询价 联系我们
PIC10F202-E/P - 8-Bit 4MHz 768B Flash MCU | Microchip
PIC10F202-E/P

PIC10F202-E/P - 8-Bit 4MHz 768B Flash MCU | Microchip

The Microchip Technology PIC10F202-E/P is a low-cost, high-performance, 8-bit, fully-static, Flash-based CMOS microcontroller housed in an 8-pin PDIP through-hole package. It features 768 bytes of Flash program memory (512 x 12 words), 24 RAM bytes, 4 MHz internal oscillator, and 4 I/O pins. According to Microchip product page data, the device operates across a 2.0V to 5.5V supply range and delivers 33 single-word/single-cycle RISC instructions for compact, deterministic code execution. A Flash microcontroller is a self-contained computing IC that combines a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), and peripherals on a single die. The PIC10F202 belongs to the 8-bit microcontroller family in the broader category of microcontrollers (MCU) within integrated circuits, sitting under the RISC architecture umbrella and optimized for cost-sensitive embedded control. Compared to competing 8-bit CISC architectures in the same price bracket, the PIC10F202 delivers roughly an order-of-magnitude higher MIPS performance due to its 1-instruction-per-cycle pipeline, with most instructions executing in 1 us at 4 MHz. Key differentiating features include 6 I/O lines shared with 4 I/O functions (one input-only pin, one output-only pin, two bidirectional), one 8-bit timer (Timer0), a watchdog timer with on-chip RC oscillator, an internal 4 MHz calibrated oscillator, and in-circuit serial programming (ICSP) capability. The device draws a typical active current under 1 mA at 4 MHz and supports a power-saving Sleep mode with wake-up on pin change. It is rated for the -40C to +125C extended industrial temperature range as indicated by the -E suffix. Architecturally, the PIC10F202 uses a Harvard-style RISC core with a 12-bit wide instruction word, providing 2:1 typical code compression versus competing 8-bit MCUs in its class. Its 4 MHz internal oscillator eliminates external clock components, reducing BOM cost and PCB area. A precision bandgap reference and on-chip POR/Brown-out Reset (BOR) improve system reliability in noisy industrial environments. Typical applications include low-cost consumer appliances, battery-powered devices, LED lighting controllers, simple sensor interfaces, and automotive accessory modules. The wide operating voltage and industrial temperature range also make it suitable for harsh-environment sensor conditioning and IoT edge nodes. In -E/P form it is supplied in a through-hole PDIP-8 package suited for prototyping, breadboarding, and field-replaceable designs. When designing with this part, note that the 4 I/O pins are shared with GP0, GP1, GP2, GP3 and the output-only GP4/GP5 functions; GP3 is input-only. The device lacks an analog comparator or ADC, so applications requiring analog signal acquisition need an external ADC companion. Programming is performed via ICSP using the ICSPCLK/ICSPDAT pins shared with GP0/GP1. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes not found on a single manufacturer datasheet page.

询价 联系我们
PIC10F202-I/P - 8-bit Flash MCU, 768B, 4MHz, 8-PDIP | Microchip
PIC10F202-I/P

PIC10F202-I/P - 8-bit Flash MCU, 768B, 4MHz, 8-PDIP | Microchip

The Microchip Technology PIC10F202-I/P is a low-cost, high-performance, 8-bit, fully-static, Flash-based CMOS microcontroller in an 8-pin PDIP through-hole package. It features 768 bytes of Flash program memory (512 x 12 words), 24 bytes of RAM, 4 MHz internal oscillator, and 4 I/O pins, with an industrial operating temperature range of -40C to +85C. The device operates from 2.0V to 5.5V and carries AEC-Q100 automotive qualification per the datasheets.com parametric record. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash, RAM, EEPROM), and peripherals onto one die. The PIC10F202 belongs to the 8-bit MCU category, which sits below 32-bit microcontrollers in compute complexity but excels in cost, deterministic real-time response, and ultra-low pin-count packages. Within Microchip's portfolio, the PIC10F family represents the smallest-footprint 8-bit PIC microcontrollers, designed for glue logic replacement and space-constrained analog/digital control. The PIC10F202 uses a RISC architecture with 33 single-word, single-cycle instructions, providing an order-of-magnitude performance advantage over competitors in the same price category. Key features include an internal 4 MHz precision oscillator eliminating external crystal requirements, four bidirectional I/O pins with individual direction control, an 8-bit timer with prescaler, and an analog comparator module. The Flash-based program memory supports in-circuit serial programming (ICSP) for field updates. The WDT, Power-on Reset, and Brown-out Detection circuitry provide robust autonomous operation. With only 6 active pins and a 1 us instruction cycle, the PIC10F202 replaces discrete logic and small ASICs in cost-sensitive designs. Typical applications include automotive subsystems requiring AEC-Q100 qualification, consumer appliance controls, LED lighting drivers, sensor signal conditioning, and IoT edge nodes. The industrial temperature grade and wide operating voltage make it suitable for both battery-powered portable devices and 5V industrial rails. When designing with this device, allocate the GP0-GP3 pins carefully because only 4 I/O are available. Use ICSP for firmware provisioning and reserve the MCLR pin as a reset input with the proper pull-up topology. The internal 4 MHz oscillator has +/- 1% accuracy over voltage and temperature, adequate for UART bit-banging but tight for CAN or USB timing.

询价 联系我们
PIC10F202T-E/OT - 8-Bit 4MHz 768B Flash MCU | Microchip | SOT-23-6
PIC10F202T-E/OT

PIC10F202T-E/OT - 8-Bit 4MHz 768B Flash MCU | Microchip | SOT-23-6

The Microchip Technology PIC10F202T-E/OT is a low-cost, high-performance 8-bit fully-static Flash-based CMOS microcontroller housed in a 6-pin SOT-23-6 package, delivering 4 MHz CPU performance with 768 bytes (512 x 12 words) of program Flash and 24 bytes of RAM in one of the industry's smallest microcontroller footprints. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, RAM, and peripherals. Within the semiconductor taxonomy, the PIC10F202T-E/OT belongs to the 8-bit microcontroller family -> RISC architecture microcontroller -> embedded controller -> semiconductor IC. It uses a 12-bit instruction word and executes 33 single-word/single-cycle instructions, with all instructions completing in 1 µs (except program branches, which take 2 µs). The device supports an operating voltage range of 2.0 V to 5.5 V, making it compatible with both 2.5 V/3.3 V and 5 V system rails. Key features include an internal 4 MHz RC oscillator (no external crystal required), 3 general-purpose I/O pins (GP0, GP1, GP2) with individual direction control, an 8-bit real-time clock/counter (TMR0) with 8-bit programmable prescaler, a watchdog timer with its own on-chip RC oscillator for reliable operation, and in-circuit serial programming (ICSP) capability. Power management features include low-power sleep mode, internal weak pull-ups, and configurable I/O wake-up-on-change. The integrated Power-on Reset (POR) and Device Reset Timer (DRT) eliminate the need for external reset circuitry. The PIC10F202 architecture leverages Microchip's enhanced mid-range core with single-cycle instruction execution, providing approximately 2:1 code compression compared to competing 8-bit MCUs. The Harvard-style separate program and data buses allow simultaneous instruction fetch and data access. In-circuit debugging is supported via the ICD interface on dedicated pins, although the small 6-pin package limits debug availability on the smallest variants. Typical applications include low-cost consumer electronics (toys, remote controls, personal care devices), LED lighting controllers, battery chargers, sensor signal conditioning, simple motor control (small fans, vibration motors), and automotive AEC-Q100 subsets (interior lighting, seat controls, accessory modules) where minimal PCB footprint and low unit cost are paramount. The wide 2.0 V to 5.5 V supply range also suits single-cell lithium-ion and two-cell alkaline battery-powered designs. When designing with the PIC10F202T-E/OT, careful pin allocation is essential because the 6-pin SOT-23-6 package exposes only 4 functional I/O/ICSP pins after VDD and VSS. The GP3 pin is input-only and used for ICSP/MCLR, while GP0, GP1, and GP2 are bidirectional. For designs requiring more I/O or peripherals, consider migrating to the pin-compatible PIC10F322 family, which offers more memory and peripherals in the same SOT-23-6 footprint. This page synthesizes distributor pricing, drop-in alternatives from the PIC10F200/PIC10F204/PIC10F220 family, and practical design notes not consolidated in the Microchip datasheet, helping engineers select the right 6-pin Flash MCU for cost-sensitive embedded designs.

询价 联系我们