微控制器

产品（19,000+)

DSPIC33EP32GS202T-I/MM - 16-bit 70 MIPS Digital Power DSC | Microchip
DSPIC33EP32GS202T-I/MM

DSPIC33EP32GS202T-I/MM - 16-bit 70 MIPS Digital Power DSC | Microchip

The Microchip Technology DSPIC33EP32GS202T-I/MM is a 16-bit digital signal controller (DSC) delivering 70 MIPS performance with 32KB of flash memory, integrated in a 28-pin QFN-S (6x6x0.9 mm) surface-mount package with exposed pad, optimized specifically for digital power conversion applications. A digital signal controller combines the computational throughput of a DSP with the peripheral set and ease of use of a microcontroller. Within the power-management hierarchy, the DSC sits between a general-purpose MCU and a dedicated digital power IC, providing programmable control loops for switched-mode power supplies, power factor correction, and motor drive systems. Key features include the dsPIC33EP core executing at 70 MIPS, DSP engine with single-cycle MAC and 40-bit accumulators, and connectivity peripherals covering I2C, SPI, UART/USART, IrDA, and LINbus. The GS variant targets digital power with dedicated SMPS peripherals, and per LCSC listing the device supports a 3V to 3.6V supply range with internal clocking up to 280 MHz for high-resolution PWM timing. Architecturally, the dsPIC33EP family uses an enhanced Harvard architecture with a 16-bit data path, pipelined instruction execution, and interrupt latency low enough to close current-mode control loops at switching frequencies in the hundreds of kilohertz. Brown-out detection and a supervisory circuit improve robustness in noisy power-electronics environments. Typical applications include interleaved power factor correction (Microchip references an interleaved PFC design producing up to 350W from universal AC input), semi-bridgeless PFC with ZVS full-bridge converters in 750W AC-DC designs, digital AC-DC power supplies, and DC-DC converters for industrial and server power. A key design consideration: the QFN exposed pad acts as the primary thermal and ground path, so it must be soldered to a solid PCB ground plane with thermal vias to realize datasheet thermal performance. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design guidance not consolidated in the manufacturer datasheet alone.

询价 联系我们
DSPIC33EP32GS202T-I/MX - 70 MIPS Digital Power DSC | Microchip
DSPIC33EP32GS202T-I/MX

DSPIC33EP32GS202T-I/MX - 70 MIPS Digital Power DSC | Microchip

The Microchip DSPIC33EP32GS202T-I/MX is a 16-bit digital signal controller (DSC) delivering 70 MIPS from its dsPIC33EP core, with 32KB of FLASH program memory, 3.3V operation, and a 28-pin UQFN (6x6 mm) package with exposed pad. It is specifically optimized for switch-mode power supply (SMPS) and digital power conversion applications. A digital signal controller combines the computational throughput of a digital signal processor with the peripheral integration and control-oriented architecture of a microcontroller. Within the power management hierarchy, DSCs sit between general-purpose MCUs and dedicated digital power ASICs, offering programmable flexibility for multi-loop control schemes such as voltage-mode, current-mode, and multi-phase regulation used in modern power electronics. Key features include high-speed PWM peripherals purpose-built for power conversion, an analog front end with comparators and programmable gain amplifier (PGA) inputs feeding a high-speed ADC, and Peripheral Pin Select (PPS) for flexible I/O remapping. The devices also carry Functional Safety (FuSa) support documentation, making them suitable for safety-relevant industrial power designs. Architecturally, the dsPIC33EP core pairs a 16-bit MCU pipeline with DSP instructions (MAC, DSP multiply) that accelerate control-law computation such as PID and compensator routines executed at switching frequencies of hundreds of kilohertz. Deterministic interrupt latency ensures tight loop timing critical to loop stability in digital power supplies. Typical applications include AC-DC power supplies, interleaved power factor correction (PFC), DC-DC converters, LED drivers, and solar micro-inverters. Microchip's Interleaved PFC reference design (universal input up to 350W) demonstrates the family directly. Design consideration: ensure adequate decoupling on VDD/AVDD and keep the analog ground return path for the ADC/PGA separate from high-current PWM switching loops to preserve analog accuracy. This page synthesizes distributor pricing, drop-in alternatives, datasheet sourcing, and practical digital power design notes not found on the manufacturer product page alone.

询价 联系我们
DSPIC33EP32GS202T-I/SO - 16-bit 70 MIPS DSC 32KB | Microchip
DSPIC33EP32GS202T-I/SO

DSPIC33EP32GS202T-I/SO - 16-bit 70 MIPS DSC 32KB | Microchip

The Microchip Technology DSPIC33EP32GS202T-I/SO is a 16-bit digital signal controller (DSC) from the dsPIC33EP GS-series for digital power applications, delivering 70 MIPS performance with 32KB of on-chip FLASH memory in a 28-pin SOIC (0.295 inch, 7.50mm width) surface-mount package, operating from 3V to 3.6V across -40C to +85C. A digital signal controller combines the compute architecture of a microcontroller with the mathematical throughput of a DSP. In the power-management hierarchy, a DSC sits between a general-purpose MCU and a dedicated DSP: it runs firmware, supervises communication, and executes the fast control loops (current-mode, voltage-mode, PFC) that switching power supplies and motor drives demand. Microchip positions the dsPIC33EP family squarely in this embedded control tier. Key features of the GS-series variant include a 70 MIPS dsPIC33E core, 32KB (32K x 8) FLASH program memory, and the high-resolution digital power peripherals that distinguish GS from GP parts, making it purpose-built for switch-mode power supply control. The device belongs to Microchip's Functional Safety (FuSa) supported dsPIC33EP lineup, easing IEC-oriented safety documentation for industrial products. Architecturally, the controller couples the 16-bit dsPIC CPU with DSP multiply-accumulate instructions, enabling single-cycle MAC operations used in digital loop compensation filters. The GS202 family data sheet (document DS70005208E) covers the dsPIC33EPXXGS202 family shared by this part. Typical applications include interleaved power factor correction (Microchip's 350W universal-input PFC reference design targets this controller family), digital SMPS and LLC power conversion, and digital lighting or motor-adjacent power control. The 28-SOIC package suits board-level power controllers where wave-solderable, hand-inspectable packages are preferred. Design consideration: budget the core regulator capacitor on the VCAP pin and decouple the 3.3V rail close to the supply pins; keep the high-frequency PWM routing away from the analog inputs used for current sensing. This page synthesizes distributor stock, pricing tiers, drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

询价 联系我们
DSPIC33EP32GS502-E/MM - 16-bit 70 MIPS DSC 32KB Flash | Microchip
DSPIC33EP32GS502-E/MM

DSPIC33EP32GS502-E/MM - 16-bit 70 MIPS DSC 32KB Flash | Microchip

The Microchip Technology DSPIC33EP32GS502-E/MM is a 16-bit Digital Signal Controller (DSC) from the dsPIC33EP GS family, engineered specifically for digital power applications. It executes up to 70 MIPS from 32KB (32K x 8) of Flash program memory and integrates interconnected high-speed PWM, high-speed ADC with Programmable Gain Amplifier (PGA), DAC and comparators in a 28-QFN-S (6x6 mm) exposed-pad package rated -40C to +125C. A Digital Signal Controller combines the computational throughput of a Digital Signal Processor (DSP) with the peripheral set and deterministic control of a microcontroller (MCU). Within the power-management hierarchy, a DSC such as the dsPIC33EP32GS502 replaces discrete analog control loops, closing voltage and current feedback digitally to achieve tighter regulation, programmable protection and software-defined topologies in Switched-Mode Power Supplies (SMPS). Key features include the interconnected high-speed PWM module with advanced switching modes (complementary, push-pull, phase-shifted, multi-phase) supporting dead-time insertion and fault handling; a high-speed 10-bit ADC with PGA enabling direct connection of low-amplitude current-shunt signals; on-chip comparators and DAC for hardware-based cycle-by-cycle current limiting; and DMA for low-overhead data transfer. Architecturally, the device belongs to the dsPIC33EP series (AEC-Q100 qualified, Functional Safety FuSa supported per DigiKey), built on a 16-bit modified Harvard core with DSP instructions (barrel shifter, MAC), operating from a 3.0V to 3.6V supply. The GS (digital power) variant distinguishes itself from the GP (general purpose) family through its power-specific analog and PWM interconnect fabric. Typical applications include SMPS digital power supplies, 350W interleaved Power Factor Correction (PFC) reference designs from Microchip, DC-DC converters, LED drivers, battery chargers, solar micro-inverters, and automotive power modules. Design consideration: use the exposed pad as the primary ground path on the PCB, and leverage the PGA to reduce external analog front-end cost; verify loop stability by sampling at PWM-frequency-synchronized rates. This page synthesizes distributor pricing, drop-in family alternatives, pin-level guidance and design notes not consolidated in the manufacturer datasheet.

询价 联系我们
DSPIC33EP32GS502-E/SO - 16-bit 60MIPS DSC 32KB | Microchip
DSPIC33EP32GS502-E/SO

DSPIC33EP32GS502-E/SO - 16-bit 60MIPS DSC 32KB | Microchip

The Microchip Technology DSPIC33EP32GS502-E/SO is a 16-bit Digital Signal Controller (DSC) delivering up to 60 MIPS from 32 KB (32K x 8) of FLASH program memory, housed in a 28-pin SOIC (SO) package with an extended -40C to +125C operating temperature range. It belongs to the dsPIC33EP GS (General Purpose, SMPS) family, purpose-built for digital power supplies and switch-mode power conversion. A Digital Signal Controller combines the computational throughput of a DSP with the peripheral set and ease of use of a microcontroller. In the power-management hierarchy, the DSC sits at the heart of a closed-loop SMPS system, replacing analog control loops with firmware-based digital control, enabling adaptive algorithms, soft-start profiles, and real-time telemetry in a single power management IC. Key features of the DSPIC33EP32GS502 include an interconnected high-speed PWM module designed for power conversion topologies, a high-speed analog-to-digital converter, on-chip DACs, programmable gain amplifiers (PGA), and analog comparators - the interconnected analog front end the manufacturer datasheet highlights as 'interconnected High-Speed PWM, ADC, PGA and Comparators.' The part also carries Microchip's Functional Safety (FuSa) support designation. Architecturally, the dsPIC33EP core executes an enhanced 16-bit instruction set with DSP multiply-accumulate instructions, allowing single-cycle MAC operations for control-law computation. Tight coupling between the ADC and PWM enables trigger-synchronized sampling at the midpoint of the switching period, minimizing control-loop latency in peak-current-mode or voltage-mode converters. Typical applications include AC-DC power supplies, power factor correction (PFC) stages, DC-DC converters, digital lighting ballasts, battery chargers, and solar micro-inverters. Microchip publishes an interleaved PFC reference design for this family. Design consideration: the -E temperature variant (-40C to +125C) makes this part suitable for automotive-adjacent and industrial environments; confirm decoupling and SOIC thermal pad copper area for high switching-frequency designs. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
DSPIC33EP32GS502-I/2N - 16-bit 70 MIPS DSC 32KB Flash | Microchip
DSPIC33EP32GS502-I/2N

DSPIC33EP32GS502-I/2N - 16-bit 70 MIPS DSC 32KB Flash | Microchip

The Microchip Technology DSPIC33EP32GS502-I/2N is a 16-bit digital signal controller (DSC) from the dsPIC33EP GS family, delivering 70 MIPS performance with 32KB of on-chip FLASH memory, a 3V to 3.6V supply range, and operation from -40C to +85C, housed in a 28-pin UQFN (6x6 mm) exposed-pad package. A digital signal controller combines the computing capabilities of a microcontroller with the signal-processing acceleration of a digital signal processor. Within the power-management hierarchy, the dsPIC DSC sits above general-purpose MCUs for control-loop-heavy tasks: it executes the fast PID and compensator math needed to close current and voltage loops inside switching power supplies, making it a cornerstone device class in digital switched-mode power supply (SMPS) design. Key features of the DSPIC33EP32GS502-I/2N include its 16-bit dsPIC33EP core clocked at up to 70 MIPS, 32KB (32K x 8) of FLASH program memory, a high-speed analog-to-digital converter tailored for power conversion sampling, and a DAC for comparator/reference duties. The GS series is Microchip's digital-power-optimized family, pairing fast ADC sampling with PWM peripherals designed for SMPS topologies such as buck, boost, LLC, and power factor correction stages. The part belongs to the Functional Safety (FuSa) qualified dsPIC 33EP series, supporting safety-conscious industrial designs. Architecturally, the device executes DSP-class instructions (MAC, divide) for control algorithms while retaining full PIC MCU peripheral compatibility. The exposed-pad UQFN-28 package improves thermal dissipation and gives short analog trace paths for the high-speed ADC inputs - important when sampling switch-node waveforms at hundreds of kilohertz. Typical applications include digital AC/DC and DC/DC power supplies, interleaved power factor correction (PFC), battery chargers, LED drivers, and digitally controlled lighting or telecom power stages. Microchip's own reference design uses the dsPIC33EP32GS502 family for an interleaved PFC application, demonstrating its fit in high-performance power conversion. When designing with this DSC, budget careful attention to ADC sampling timing versus PWM update rates - the whole point of the GS family is deterministic loop closure - and use the exposed thermal pad for ground return of the analog domain. This page synthesizes distributor pricing, drop-in same-family alternatives, practical design notes, and comparison data not found in the manufacturer datasheet alone.

询价 联系我们
DSPIC33EP32GS502T-E/MX - 16-bit 60MIPS Digital Power DSC | Microchip
DSPIC33EP32GS502T-E/MX

DSPIC33EP32GS502T-E/MX - 16-bit 60MIPS Digital Power DSC | Microchip

The Microchip Technology DSPIC33EP32GS502T-E/MX is a 16-bit digital signal controller (DSC) from the dsPIC33EP GS (digital power) family, delivering up to 70 MIPS-class performance (60 MIPS at 3.3V operation per the GS50x family), 32KB of Flash program memory, and a dedicated high-speed PWM module for digital power conversion, housed in a 28-pin UQFN (6x6 mm) exposed-pad package with extended temperature range. A digital signal controller combines the computational throughput of a DSP with the peripheral integration and control peripherals of a microcontroller. Within the power-management hierarchy, the dsPIC33EP GS family sits between general-purpose MCUs and dedicated digital power ICs: it runs closed-loop control firmware for switch-mode power supplies, power factor correction stages, and motor drives, replacing analog control loops with software-defined control. Key differentiating features include the interconnected high-speed PWM module designed for power topologies such as buck, boost, half-bridge, and interleaved PFC; an ADC with programmable gain amplifier (PGA) and comparators that can trigger PWM updates without CPU intervention; and AEC-Q100 automotive qualification with an extended -40C to +125C operating range denoted by the E temperature suffix. Architecturally, the device uses the enhanced dsPIC33E 16-bit core with DSP instruction support (MAC, multiply-divide) for fast control-loop execution, plus DMA for autonomous data movement between the ADC and RAM. The GS family datasheet (document 70005127) describes the interconnected PWM, ADC, PGA, and comparator resources designed specifically for digital power applications. Typical applications include interleaved power factor correction (Microchip's 350W Interleaved PFC reference design uses this family), DC-DC converters, LED drivers, and AC-DC power supplies requiring software-controlled feedback loops. Design consideration: the 28-UQFN exposed pad must be soldered to a solid ground plane for thermal and electrical performance; follow the GS50x family datasheet layout guidance for the analog (AVDD/AVSS) supply filtering to preserve ADC accuracy. This page synthesizes distributor listings, drop-in same-package alternatives, and digital-power design notes not consolidated on the manufacturer product page.

询价 联系我们
DSPIC33EP32GS502T-E/SO - 16-bit 60 MIPs DSC 32KB | Microchip
DSPIC33EP32GS502T-E/SO

DSPIC33EP32GS502T-E/SO - 16-bit 60 MIPs DSC 32KB | Microchip

The Microchip Technology DSPIC33EP32GS502T-E/SO is a 16-bit dsPIC33EP (GS series) Digital Signal Controller delivering 60 MIPS from 32KB (32K x 8) FLASH and 4KB RAM, housed in a 28-pin SOIC (7.50 mm width) surface-mount package. It operates from a 3V to 3.6V supply, offers 21 I/O pins, and is rated from -40C to +125C with AEC-Q100 automotive qualification and Functional Safety (FuSa) documentation support. A Digital Signal Controller (DSC) is a hybrid device class that merges the control-path familiarity of a general-purpose microcontroller with the arithmetic throughput of a digital signal processor. Within the power-management IC hierarchy, DSCs sit above simple analog controllers and alongside MCUs and DSPs, serving as the intelligent core of switching power supplies, motor drives, and digital power conversion systems. Key features include the 70 MIPS-class dsPIC33EP core running at 60 MHz (60 MIPs), on-chip high-speed PWM peripherals purpose-built for SMPS control, DSP engine instructions with barrel shifter support, boundary-scan (JTAG) debug, and multiple low-power modes. The GS (digital power) variant adds specialized analog and timing blocks tailored to power conversion loops. Architecturally, the dsPIC33E core uses a modified Harvard pipeline with DSP multiply-accumulate instructions, enabling deterministic loop execution for current-mode and voltage-mode control. The E/SO temperature suffix and T (tape-and-reel) packing target automated assembly in industrial and automotive builds. Typical applications include interleaved power factor correction (Microchip's 350W universal-input interleaved PFC reference design targets this device family), LLC and buck/boost digital power supplies, BLDC/PMSM motor control, and digital lighting ballasts. Design tip: budget the 3.3V rail carefully - the device is specified at 3V to 3.6V only, and core voltage is internally regulated from VCAP, so decoupling and VCAP capacitance must follow the datasheet exactly. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
DSPIC33EP32GS502T-I/MM - 70MIPS DSC, 32KB Flash | Microchip
DSPIC33EP32GS502T-I/MM

DSPIC33EP32GS502T-I/MM - 70MIPS DSC, 32KB Flash | Microchip

The Microchip Technology DSPIC33EP32GS502T-I/MM is a 16-bit digital signal controller (DSC) delivering 70 MIPS core performance with 32 KB of Flash program memory, housed in a 28-pin QFN-S (6x6 mm, MM) surface-mount package with exposed pad. It operates from a 3.0 V to 3.6 V supply and targets digital power conversion. A digital signal controller combines the computational throughput of a digital signal processor (DSP) with the peripheral integration and control-oriented architecture of a microcontroller. Within the power-management hierarchy, the dsPIC33EP GS family sits at the heart of digital switch-mode power supplies (SMPS), replacing analog control loops with firmware-executed control laws executed at high interrupt rates. Key features of the GS-series DSC include the 70 MIPS dsPIC33E core, high-resolution PWM modules purpose-built for power topologies, fast ADC sampling for current-loop feedback, and connectivity via I2C, SPI, UART/USART, IrDA, and LINbus. The 32 KB Flash accommodates full closed-loop control firmware plus communication stacks, while the industrial temperature grade (-40C to +85C, I-suffix) suits embedded power electronics. Architecturally, the device pairs a 16-bit modified Harvard core with DSP instruction support and zero-overhead loops, allowing deterministic execution of proportional-integral control loops. The Peripheral Trigger Generator coordinates ADC sampling with PWM events, minimizing loop latency - the critical metric in peak-current-mode and voltage-mode digital control. Typical applications include interleaved power factor correction (PFC) up to 350 W, semi-bridgeless PFC with ZVS full-bridge converters up to 750 W (per Microchip reference designs), digital AC-DC supplies, and motor control drives. The QFN-28 6x6 footprint keeps solutions compact for power-density-sensitive designs. Design consideration: route the exposed thermal pad to a solid ground plane and keep high dv/dt switch nodes away from the ADC reference pins to preserve current-sense accuracy. This page synthesizes distributor pricing, drop-in family alternatives, and practical digital-power design notes not found in the manufacturer datasheet, with pricing as of 2026-09-25.

询价 联系我们
DSPIC33EP32GS504-E/ML - 60 MIPS 16-bit DSC 44-QFN | Microchip
DSPIC33EP32GS504-E/ML

DSPIC33EP32GS504-E/ML - 60 MIPS 16-bit DSC 44-QFN | Microchip

The Microchip Technology DSPIC33EP32GS504-E/ML is a 16-bit Digital Signal Controller (DSC) delivering up to 60 MIPS performance, 32 KB (32K x 8) of Flash program memory, and integrated high-speed analog peripherals, housed in a 44-pin QFN (8x8 mm) surface-mount package. It belongs to the dsPIC33EP GS50X family purpose-built for digital power (SMPS) applications. A Digital Signal Controller combines the computational architecture of a microcontroller with DSP features such as single-cycle multiply-accumulate and hardware divide, making the dsPIC DSC category a middle tier between general-purpose MCUs and dedicated DSPs. Within the power-management hierarchy, it acts as the digital control engine that closes feedback loops for converters and supplies. Key features include a 16-bit dsPIC33EP core, high-speed 12-bit ADC with multiple sample-and-hold modules for simultaneous sampling, on-chip comparators and DACs dedicated to power-conversion feedback, PWM modules with advanced timing for SMPS topologies, and Functional Safety (FuSa) support per Microchip's product classification. The -E temperature suffix denotes extended operation from -40C to +125C, suiting harsh industrial environments. Technically, the GS series integrates peripherals such as the High-Speed PWM with fault protection, 3.3V operation, and in-circuit programming (ICSP) via the PGC/PGD pins. The 44-QFN exposed-pad package offers low inductance and good thermal performance for dense power boards. Typical applications include AC-DC and DC-DC digital power supplies, power factor correction (PFC) stages, LED drivers, and battery charging systems. Design consideration: allocate PWM/ADC peripheral pin mapping early, since the analog input multiplexing constrains which pins can sense feedback signals. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
DSPIC33EP32GS504-I/ML - 16-Bit 70 MIPS DSC 32KB Flash | Microchip
DSPIC33EP32GS504-I/ML

DSPIC33EP32GS504-I/ML - 16-Bit 70 MIPS DSC 32KB Flash | Microchip

The Microchip Technology DSPIC33EP32GS504-I/ML is a 16-bit digital signal controller (DSC) from the dsPIC33EP32GS504 family for digital power applications, delivering 70 MIPS performance, 32KB (32K x 8) of Flash memory, and 4K x 8 of RAM in a 44-pin QFN (8x8 mm) package with exposed pad. It integrates an interconnected high-speed PWM module, high-speed 12-bit ADC, DAC, programmable gain amplifiers (PGA), and analog comparators tailored for switch-mode power supply control. A digital signal controller combines the computational throughput of a DSP core with the deterministic interrupt architecture and peripheral set of a microcontroller. Within the power-management hierarchy, the dsPIC33EP family occupies the role of the digital control loop engine in SMPS, PFC, and power-conversion systems, replacing analog control ICs where flexibility, adaptive algorithms, and communication are required. Key differentiating features include a 70 MIPS dsPIC33E core operating at 3.3V, seven high-resolution PWM channels with advanced timing for peak current mode control, a 12-bit ADC capable of sampling up to 4 Msps in specific configurations, and hardware support for functional safety (FuSa) development. The interconnected PWM-ADC-comparator fabric minimizes control-loop latency, a decisive parameter in digital power conversion where loop delay directly limits achievable bandwidth. The architecture couples a 16-bit modified Harvard core with DSP instructions (MAC, DSP multiply) executed in single cycle, plus an internal fast RC oscillator and PLL for clock generation. Operating temperature for the -I suffix is -40C to +85C (industrial), with supply voltage of 3.0V to 3.6V. Typical applications include AC-DC and DC-DC digital power supplies, power factor correction stages, solar micro-inverters, battery chargers, LED drivers, and embedded motor control. Microchip's 750W AC-DC reference design (semi-bridgeless PFC followed by peak-current-controlled ZVS full-bridge with digital slope compensation) is based on this family. Design consideration: budget PWM resolution against converter switching frequency - at 70 MIPS, effective PWM resolution degrades at very high switching frequencies, so verify step size per the family datasheet. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical digital-power design notes beyond what the manufacturer datasheet provides.

询价 联系我们
DSPIC33EP32GS504T-I/ML - 16-bit 70 MIPS DSC 32KB | Microchip
DSPIC33EP32GS504T-I/ML

DSPIC33EP32GS504T-I/ML - 16-bit 70 MIPS DSC 32KB | Microchip

The Microchip DSPIC33EP32GS504T-I/ML is a 16-bit digital signal controller (DSC) delivering 70 MIPS performance with 32KB (32K x 8) of FLASH program memory, housed in a 44-pin QFN (8x8 mm) exposed-pad package rated from -40C to +85C. A digital signal controller combines the compute throughput of a DSP with the peripheral integration and control-oriented architecture of a microcontroller. Within the power-management hierarchy, the dsPIC33EPXXGS50X family sits at the intersection of digital signal processors and SMPS control ICs, replacing analog control loops with high-resolution digital feedback for switch-mode power supplies. Key features include the interconnected high-speed PWM module designed for multi-loop digital power conversion, a high-speed 12-bit ADC with multiple sample-and-hold circuits, on-chip comparators and a programmable gain amplifier (PGA), plus I2C, SPI, IrDA, UART and USART serial interfaces. The device provides 35 I/O pins, brown-out detect/reset, power-on reset and a watchdog timer for robust standalone operation. Technically, the dsPIC33EP core executes an enhanced instruction set with DSP multiply-accumulate instructions, enabling tight control-loop execution at fixed intervals. According to the dsPIC33EPXXGS50X family datasheet (70005127d), the interconnected PWM, ADC and comparator blocks can trigger each other without CPU intervention, minimizing loop latency in peak-current-mode converters. Typical applications include interleaved power factor correction (PFC) up to 350W, 750W semi-bridgeless PFC plus ZVS full-bridge AC-DC converters, LLC resonant supplies, solar micro-inverters, and battery chargers, where deterministic digital control at high PWM resolution is required. Design consideration: the 3V-3.6V supply range requires a clean 3.3V rail; decouple VDD/VDDCORE per the datasheet and verify the 44-QFN exposed pad is well soldered to a ground plane for thermal and EMI performance. This page synthesizes verified distributor data, drop-in alternatives, pricing tiers, and digital-power design notes not found on the manufacturer product page alone.

询价 联系我们
DSPIC33EP32GS504T-I/PT - 70MIPS 32KB Flash DSC 44-TQFP | Microchip
DSPIC33EP32GS504T-I/PT

DSPIC33EP32GS504T-I/PT - 70MIPS 32KB Flash DSC 44-TQFP | Microchip

The Microchip Technology DSPIC33EP32GS504T-I/PT is a 16-bit dsPIC33EP digital signal controller (DSC) delivering 70 MIPS from a 32KB (32K x 8) Flash memory, housed in a 44-pin TQFP (10x10 mm) package, operating at 3.3V across the industrial -40C to +125C temperature range. A digital signal controller combines the compute throughput of a DSP with the peripheral integration and deterministic control of a microcontroller. Within the power-management hierarchy, the DSC sits at the top of embedded control ICs, closing high-bandwidth feedback loops for switch-mode power conversion where a general-purpose MCU cannot meet loop-update-rate requirements. Key features include the SMPS-oriented dsPIC33EP GS core rated at 70 MIPS, a high-speed 12-bit ADC with multiple sample-and-hold circuits for simultaneous multi-rail sensing, on-chip DAC comparators, and high-resolution PWM (HRPWM) peripherals purpose-built for digital power. The GS (General Purpose SMPS) family also integrates DMA, UART, SPI, and I2C for supervisory communication, and the device is part of Microchip's Functional Safety (FuSa) offering per DigiKey classification. Architecturally, the DSP engine provides single-cycle MAC and dual 40-bit accumulators, enabling execution of compensator and filter code within tight PWM interrupt budgets. The Flash-based program memory supports in-circuit self-programming, and the peripheral ecosystem is shared across the dsPIC33EP family for code reuse. Typical applications include AC-DC power supplies, interleaved power factor correction (Microchip's 350W Interleaved PFC reference design targets this device), DC-DC converters, digital lighting ballasts, and battery chargers. When designing with this device, budget the ADC sampling and compensator execution against the 70 MIPS core so loop bandwidth and PWM update rates are met with margin. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
DSPIC33EP32GS505T-E/PT - 16-bit DSC 70MIPS Digital Power | Microchip
DSPIC33EP32GS505T-E/PT

DSPIC33EP32GS505T-E/PT - 16-bit DSC 70MIPS Digital Power | Microchip

The Microchip Technology DSPIC33EP32GS505T-E/PT is a 16-bit Digital Signal Controller (DSC) for digital power applications, delivering up to 70 MIPS from 32 KB of Flash memory in a 48-pin TQFP with exposed pad (7x7 mm), qualified for -40C to +125C extended temperature operation. A Digital Signal Controller merges the computational throughput of a DSP with the peripheral integration and control-oriented architecture of a microcontroller, sitting in the product hierarchy between a general-purpose MCU and a dedicated DSP. The dsPIC33EP family executes an enhanced 16-bit core with DSP multiply-accumulate instructions, making it a power-management IC controller rather than a power device itself: it generates the control loops that drive converters, PFC stages and inverters. Key differentiating features include an interconnected high-speed PWM module purpose-built for switching power supplies, on-chip high-speed analog comprising ADC inputs with an integrated Programmable Gain Amplifier (PGA) and analog comparators, and a 3.0 V to 3.6 V supply range. The extended -40C to +125C rating of the /E temperature suffix supports industrial and automotive-adjacent environments. Architecturally, the interconnected PWM, ADC/PGA and comparator blocks are designed to operate together with minimal CPU intervention, enabling fast inner current loops in peak-current-mode or average-current-mode topologies. This interconnect offloads the 70 MIPS core, allowing a single controller to manage multiple power stages with deterministic latency. Typical applications include interleaved power factor correction, as demonstrated in Microchip's 350 W universal-input Interleaved PFC reference design built on the dsPIC33EP32GS505, plus LLC and phase-shifted full-bridge DC-DC converters, solar micro-inverters, and digital lighting ballasts. When designing, reserve the dedicated PWM and analog-capable pins early in layout, since the interconnected PWM routing is pin-position dependent; decouple the 3.3 V rail locally at each supply pin pair. This page synthesizes distributor pricing, same-family drop-in options, and practical digital-power design notes not consolidated in the manufacturer datasheet.

询价 联系我们
DSPIC33EP32GS506-E/PT - 16-bit DSC 70MIPS 32KB Flash | Microchip
DSPIC33EP32GS506-E/PT

DSPIC33EP32GS506-E/PT - 16-bit DSC 70MIPS 32KB Flash | Microchip

The Microchip Technology DSPIC33EP32GS506-E/PT is a 16-bit digital signal controller (DSC) from the dsPIC33EP32GS506 family optimized for digital power applications, delivering up to 70 MIPS performance with 32 KB of Flash program memory in a 64-pin TQFP (PT) package with extended temperature range (-40C to +125C). A digital signal controller combines the computational capability of a digital signal processor with the peripheral set and ease of use of a microcontroller. Within the power-management hierarchy, a DSC sits between a general-purpose MCU and a dedicated DSP: it executes closed-loop control algorithms such as power factor correction, LLC resonant control, and interleaved buck conversion at switching frequencies that general MCUs cannot sustain. Key features include a high-speed 12-bit ADC (up to 10 Msps) with up to 16 channels for simultaneous multi-rail current and voltage sensing, an on-chip high-speed PWM module with dedicated time base and complementary outputs purpose-built for SMPS topologies, DAC outputs for comparator references, and the dsPIC33E core running at up to 70 MIPS from a 3.3V supply. The device is identified by Microchip as Functional Safety (FuSa) capable. Architecturally, the dsPIC33E core uses a modified Harvard pipeline with DSP-style multiply-accumulate (MAC) instructions and a barrel shifter, enabling single-cycle execution of the PID and filter mathematics at the heart of digital power loops. Boundary scan and multiple PGECx/PGEDx ICSP pairs simplify in-circuit debug and programming. Typical applications include AC-DC power supplies with interleaved power factor correction, DC-DC converters, solar micro-inverters, LED drivers, battery chargers, and uninterruptible power supplies. Microchip provides an interleaved PFC reference design specifically for this SMPS DSC family. Design consideration: connect every VDD and VSS pin pair on the 64-TQFP and pair PGECx with its matching PGEDx for programming; mismatched ICSP pairs are a common bring-up failure. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
DSPIC33EP32MC202-H/SS - 16-bit DSC, 32KB Flash, 60MIPS | Microchip
DSPIC33EP32MC202-H/SS

DSPIC33EP32MC202-H/SS - 16-bit DSC, 32KB Flash, 60MIPS | Microchip

The Microchip Technology DSPIC33EP32MC202-H/SS is a 16-bit digital signal controller (DSC) from the dsPIC33EP family with a 32KB Flash program memory, 4KB RAM, and a 60 MIPS dsPIC DSC core, housed in a 28-pin SSOP package (0.209 in / 5.30 mm width). A digital signal controller combines the compute throughput of a microcontroller with DSP-grade math acceleration in a single chip. In the power-management hierarchy of embedded systems, a DSC sits between a general-purpose MCU and a dedicated DSP: it executes C code and real-time operating tasks like an MCU while also providing hardware multiply-accumulate and high-resolution PWM peripherals purpose-built for closed-loop control of motors and power converters. Key features of the DSPIC33EP32MC202-H/SS include the 60 MHz (60 MIPS) dsPIC33EP CPU core, 32KB of self-programmable Flash organized as 10.7K x 24-bit instruction words, 4KB of SRAM, four DMA channels, five 16-bit timers, four external interrupt inputs, and a 6-channel 10-bit/12-bit analog-to-digital converter. The MC (Motor Control) variant adds high-resolution Motor Control PWM outputs and comparator inputs suited for field-oriented control (FOC) and sensorless algorithms. The device integrates DSP engine instructions, brown-out reset, power-on reset, and In-Circuit Serial Programming (ICSP) via any PGECx/PGEDx pair. Multiple external interrupt sources and DMA offload the CPU during high-rate ADC sampling, keeping loop closure deterministic for control applications. Typical applications include brushless DC and PMSM motor drives, digital power supplies (LLC, boost, PFC stages), electric tool controls, HVAC blowers, and industrial automation nodes where 3.3V operation and AEC-Q100 qualification matter. Design consideration: this is an H-suffix (automotive/extended screening) part; verify the temperature grade needed for your enclosure before layout, and always tie all VDD/VSS pairs per the datasheet power delivery guidance. This page synthesizes distributor data, same-family drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

询价 联系我们
DSPIC33EP32MC202-I/SO - 70 MIPS Motor Control DSC, 28-SOIC | Microchip
DSPIC33EP32MC202-I/SO

DSPIC33EP32MC202-I/SO - 70 MIPS Motor Control DSC, 28-SOIC | Microchip

The Microchip DSPIC33EP32MC202-I/SO is a 16-bit digital signal controller (DSC) from the dsPIC33EP32MC202 family, delivering 70 MIPS core performance with 32KB (10.7K x 24) of FLASH program memory and 4KB of RAM in a 28-pin SOIC (7.50 mm body width) package rated for -40C to +85C industrial operation. It is purpose-built for high-performance precision motor control and digital power conversion. A digital signal controller (DSC) is a hybrid device that combines the deterministic control strengths of a microcontroller with the high-throughput numeric capabilities of a digital signal processor on a single core. Within the embedded-controller taxonomy, the dsPIC33EP family sits above basic MCUs by adding a DSP engine with single-cycle MAC, high-speed motor-control PWM, and integrated analog peripherals - making it a dedicated motor-control and digital-power platform rather than a general-purpose processor. Key differentiating features include the 70 MIPS dsPIC DSC core, dedicated motor-control PWM (MCPWM) outputs, a quadrature encoder interface (QEI) for rotor position feedback, two integrated operational amplifiers for current sensing, three analog comparators, and a peripheral trigger generator (PTG). These on-chip peripherals reduce external component count in closed-loop motor drives and allow direct interfacing with current-sense shunts and incremental encoders without external glue logic. Architecturally, the dsPIC33E core pairs a 16-bit modified Harvard pipeline with DSP multiply-accumulate instructions and single-cycle MAC, enabling fast execution of control-loop math such as PI, PID, and field-oriented-control algorithms. Operating at up to 60 MHz internal clock speed, it sustains deterministic control-loop times for FOC, sinusoidal commutation, and sensorless observer schemes used in modern BLDC and PMSM drives. Typical applications include brushless DC (BLDC) and permanent magnet synchronous motor (PMSM) drives, switched-mode power supplies and digital power conversion, battery chargers, and industrial automation equipment where precision control and energy efficiency are required. A key design consideration: the -I suffix grades this part for -40C to +85C ambient operation; designs targeting wider industrial or extended-temperature ranges should consider the -E temperature variant of the same die. Program via ICSP using tools such as PICkit 3/4 or MPLAB ICD. This page synthesizes distributor pricing, verified drop-in alternatives in the same 28-SOIC footprint, pinout data, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
DSPIC33EP32MC202T-E/MM - 16-bit 60MIPS DSC 32KB QFN-28 | Microchip
DSPIC33EP32MC202T-E/MM

DSPIC33EP32MC202T-E/MM - 16-bit 60MIPS DSC 32KB QFN-28 | Microchip

The Microchip DSPIC33EP32MC202T-E/MM is a 16-bit digital signal controller (DSC) from the dsPIC33EP family, delivering 60 MIPS performance with 32KB (10.7K x 24) of FLASH program memory and 4KB of RAM, housed in a 28-pin QFN-S (6x6 mm) exposed-pad package rated for -40C to +125C operation. A digital signal controller combines the deterministic control flow of a microcontroller with the math throughput of a DSP. In the power-management hierarchy, the dsPIC33EP family sits between general-purpose MCUs and dedicated DSPs, offering a Harvard-architecture 16-bit core with DSP multiply-accumulate instructions, making it a strong fit for closed-loop control systems such as field-oriented motor control, digital power conversion, and sensor fusion. Key features include the 16-bit dsPIC33E core executing at up to 60 MIPS from internal FLASH, an extended-temperature (-40C to +125C) rating suitable for automotive and harsh industrial environments, and AEC-Q100 qualification. The MC-class variants integrate high-speed PWM peripherals and advanced analog blocks that Microchip designed specifically for precision motor control applications. The device operates from a single 3.0V to 3.6V supply. Technically, the core integrates DSP engine features (single-cycle MAC, dual operand fetch) with the dsPIC instruction set, and the E-generation adds a more capable interrupt architecture and enhanced peripherals versus the older dsPIC33F series. The QFN-28 package with exposed pad provides good thermal performance for a small 6x6 mm footprint. Typical applications include BLDC/PMSM motor drives, digital power supplies (LLC, totem-pole PFC), automotive auxiliary actuators, and industrial sensor interfaces where deterministic 60 MIPS compute is required. Design consideration: decouple VDD with a low-ESR ceramic capacitor close to the pins and always fit the VCAP/VDDCORE capacitor specified in the family datasheet - omitting it prevents core regulation and the device will not start. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in a single manufacturer datasheet.

询价 联系我们
DSPIC33EP32MC203T-E/TL - 16-Bit 60MIPs 32KB DSC | Microchip
DSPIC33EP32MC203T-E/TL

DSPIC33EP32MC203T-E/TL - 16-Bit 60MIPs 32KB DSC | Microchip

The Microchip Technology DSPIC33EP32MC203T-E/TL is a 16-bit digital signal controller (DSC) from the dsPIC33EP32MC20x motor-control family, delivering up to 60 MIPs of core performance with 32KB (10.7K x 24) of FLASH program memory and 2KB of RAM in a 36-pin VTLA (5x5 mm) QFN package with exposed pad, qualified to AEC-Q100 for automotive-grade applications. A digital signal controller combines the computational power of a 16-bit microcontroller with the deterministic execution of a DSP core in a single chip. In the embedded-systems hierarchy, the DSC sits between a general-purpose MCU and a dedicated DSP, making the dsPIC33EP family a natural choice for closed-loop control systems such as field-oriented motor control, digital power conversion, and sensor-fusion algorithms that need both fast math and flexible peripherals. Key features include the 60 MIPs dsPIC33EP core with integrated DSP multiply-accumulate instructions, 32KB of self-programmable FLASH, and hardware support for the motor-control peripherals (complementary PWM, quadrature encoder interfaces, and fast 10/12-bit ADC sampling) that define the MC20x subfamily. The -E temperature grade supports -40C to +125C ambient operation, and the compact 5x5 mm exposed-pad QFN minimizes PCB area in dense power-electronics layouts. Technically, the dsPIC33EP core executes most instructions in a single cycle at up to 60 MIPs from a 3.3V supply, with DSP instructions and hardware dividers accelerating control-loop mathematics. According to the Microchip product page, the family is designed to enable high-performance, precision motor-control systems with integrated DSP and enhanced on-chip peripherals. Typical applications include brushless DC and PMSM motor drives, digital power supplies and LED drivers, automotive auxiliary actuators, and industrial sensor interfaces. The MC20x peripheral set is purpose-built for these control loops, where deterministic PWM update and fast analog sampling directly affect system efficiency and stability. When designing, budget the 2KB RAM carefully for control-state variables and communication buffers, and exploit the exposed pad for ground thermal relief on the 5x5 mm QFN footprint. This page synthesizes distributor pricing context, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet. Pricing shown is an estimate as of 2026-09-25.

询价 联系我们
DSPIC33EP32MC204-E/PT - 60MHz 16-bit DSC 32KB Flash TQFP-44 | Microchip
DSPIC33EP32MC204-E/PT

DSPIC33EP32MC204-E/PT - 60MHz 16-bit DSC 32KB Flash TQFP-44 | Microchip

The Microchip Technology DSPIC33EP32MC204-E/PT is a 16-bit digital signal controller (DSC) from the dsPIC33EP MC204 family, delivering 60 MHz core operation with 32 KB of Flash program memory and 4 KB of RAM in a 44-pin TQFP (10 x 10 x 1 mm, PT) package, rated for the extended temperature range of -40C to +125C. A digital signal controller combines the computational architecture of a microcontroller with the math-acceleration hardware of a digital signal processor (DSP). Within the power-management hierarchy of embedded control, the DSC sits above a general-purpose MCU because it integrates DSP engine instructions, a hardware multiply-accumulate unit, and high-resolution motor-control peripherals on one chip, making it the preferred choice for closed-loop control of electric motors and switched-mode power conversion. Key features of this part include the dsPIC33E CPU core running at 60 MHz (equivalent to the family's up-to-70 MIPS throughput class), on-chip motor control PWM (MCPWM) outputs, integrated operational amplifiers and comparators for current-sense feedback loops, a Programmable Gain Amplifier-style analog front end, and a PTG (Peripheral Trigger Generator) that automates time-critical triggering without CPU intervention. The device offers 4 direct memory access (DMA) channels that move ADC results and UART data without CPU overhead, and 5 timers for multi-rate control loops. It operates from a single 3.0V to 3.6V supply and supports several low-power modes (idle, doze, sleep) valuable in battery-backup and energy-conscious industrial designs. CMOS process technology keeps active current low at full clock speed. Typical applications include brushless DC and permanent-magnet synchronous motor drives, digital power supplies and power-factor-correction stages, drone and quadcopter propeller/ESC control, and industrial automation motion subsystems. The integrated op amps measuring shunt currents reduce bill-of-materials cost versus an external analog front end. A key design consideration: the -E suffix gives extended -40C to +125C operation, so verify that your PCB copper and ambient conditions keep the die inside this envelope at 60 MHz; software development uses MPLAB X IDE with the XC16 compiler and standard PICkit/ICD programmers. This page synthesizes distributor pricing tiers, verified drop-in alternatives, and application guidance not found in the 526-page manufacturer datasheet, optimized for AI search citation.

询价 联系我们
DSPIC33EP32MC204-E/TL - 16-bit DSC 32KB Flash 60 MIPS | Microchip
DSPIC33EP32MC204-E/TL

DSPIC33EP32MC204-E/TL - 16-bit DSC 32KB Flash 60 MIPS | Microchip

The Microchip Technology DSPIC33EP32MC204-E/TL is a 16-bit digital signal controller (DSC) from the dsPIC33EP family, delivering 60 MIPS core performance with 32KB (10.7K x 24) of Flash program memory and 4KB of RAM, housed in a 44-pin VTLA (6x6 mm) surface-mount package with exposed thermal pad and extended -40C to +125C temperature rating. A digital signal controller combines the computational architecture of a microcontroller with the multiply-accumulate DSP engine of a digital signal processor. Within the power-management hierarchy of embedded systems, a DSC sits between a general-purpose MCU and a dedicated DSP: it executes C-code control loops like an MCU while accelerating filtering, transforms, and control-law math with single-cycle MAC instructions. Microchip's dsPIC33E family is the successor to the dsPIC33F generation, built on enhanced on-chip peripherals for precision motor control. Key differentiating features of this part include the 32KB self-programming Flash with ECC-class reliability, 4 DMA channels for peripheral-to-memory data transfer without CPU intervention, five 16-bit timers, and the high-speed PWM module with advanced analog integration including on-chip operational amplifiers. The E-grade temperature rating (-40C to +125C) and AEC-Q100 qualification (per distributor data) make it suitable for automotive and harsh-environment designs. Architecturally, the dsPIC33EP core operates from a 3.0V to 3.6V single supply with a 16-bit modified Harvard pipeline, two 40-bit accumulators, and hardware divide support. Four DMA channels offload the CPU in ADC-sampled control loops, and multiple low-power modes reduce average current in battery-adjacent products. Typical applications include three-phase PMSM and BLDC motor drives, digital power supplies (power factor correction, LLC control), drone propeller/quadcopter flight control (a Microchip reference design targets this part directly), and automotive auxiliary motor control. When designing, budget the 32KB Flash carefully - the DSP library and motor-control middleware can consume significant program space; a 4KB RAM ceiling also constrains complex control algorithms. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
DSPIC33EP32MC204-H/ML - 70 MIPS Motor Control DSC | Microchip
DSPIC33EP32MC204-H/ML

DSPIC33EP32MC204-H/ML - 70 MIPS Motor Control DSC | Microchip

The Microchip Technology DSPIC33EP32MC204-H/ML is a 16-bit digital signal controller (DSC) from the dsPIC33EP family, delivering up to 70 MIPS performance with 32 KB of Flash program memory and 4 KB of SRAM in a 44-pin QFN package with exposed pad. It operates from a single 3.3 V supply, runs a 60 MHz internal clock, and is qualified to AEC-Q100 for automotive applications. A digital signal controller combines the compute architecture of a microcontroller with the DSP capabilities of a digital signal processor. In the power-management hierarchy of embedded systems, a DSC sits between general-purpose MCUs and dedicated DSPs: it offers deterministic single-cycle multiply-accumulate (MAC) instructions for control-loop math while retaining the peripherals, interrupt structure, and ease of use of a conventional 16-bit MCU. Key features of the DSPIC33EP32MC204-H/ML include the dsPIC33E core executing at 70 MIPS, dedicated motor-control peripherals such as a high-speed PWM module with complementary outputs and dead-time insertion, multiple UART/SPI/I2C communication interfaces, several 16-bit timers, and analog resources including ADC inputs and comparators. The -H suffix denotes an extended operating temperature grade suited to high-reliability environments. Architecturally, the dsPIC33E core uses an enhanced Harvard bus structure with a 17-bit by 17-bit hardware multiplier, 32-bit multiply support, and a flexible DSP engine with two 40-bit accumulators, enabling fast execution of PID, Clarke/Park transforms, and space-vector modulation for precision motor control. Typical applications include three-phase PMSM and BLDC motor drives, drone propeller ESCs (Microchip publishes a dedicated Drone Propeller Reference Design based on this exact device), digital power supplies, and industrial automation nodes. When designing with this device, verify that the 4 KB RAM budget accommodates your control-loop state variables and DSP buffers, and decouple the 3.3 V rail with low-ESR ceramics at both VDD/VDDCORE pins per the Microchip reference layout. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
DSPIC33EP32MC204-I/MV - 70 MIPS 16-Bit Motor Control DSC | Microchip
DSPIC33EP32MC204-I/MV

DSPIC33EP32MC204-I/MV - 70 MIPS 16-Bit Motor Control DSC | Microchip

The Microchip Technology DSPIC33EP32MC204-I/MV is a 16-bit digital signal controller (DSC) from the dsPIC33EP MC (Motor Control) family, delivering 70 MIPS performance with 32 KB (10.7K x 24) of Flash program memory and 4 KB of RAM, housed in a 48-pin UQFN (6x6 mm) package. A digital signal controller combines the compute architecture of a microcontroller with the mathematical acceleration of a DSP. Within the power-management hierarchy, the dsPIC33EP MC family sits at the intersection of MCU and DSP, pairing a 16-bit dsPIC DSC core with DSP instructions (MAC, DSP multiply) and analog peripherals such as op amps and comparators, so a single chip can close high-speed control loops that would otherwise require a microcontroller plus external signal-conditioning ICs. Key features include a 70 MIPS core, dedicated Motor Control PWM (MCPWM) modules, integrated analog op amps and comparators, CAN support, and Microchip's Peripheral Trigger Generator (PTG) for autonomous peripheral sequencing. These peripherals reduce external component count and CPU loading in digital power and motor-drive designs. Architecturally, the dsPIC33EP core executes an enhanced two-stage pipeline at up to 70 MIPS from a 32-bit instruction word, with hardware DSP multiply-accumulate supporting fast PID, Clarke/Park transforms, and current-loop control at tens of kilohertz switching frequencies. Typical applications include three-phase BLDC/PMSM motor drives for drones and quadcopters (Microchip publishes a dsPIC33EP32MC204 Drone Propeller Reference Design, DS70005545), digital power supplies and PFC stages, and industrial motion control. Design tip: budget the 4 KB of RAM carefully, as large control-law buffers and FFT workloads can exhaust it quickly. This page synthesizes distributor availability data, same-package alternatives, and motor-control design guidance not consolidated in the manufacturer datasheet.

询价 联系我们
DSPIC33EP32MC204-I/TL - 16-bit 70 MIPS DSC 32KB Flash | Microchip
DSPIC33EP32MC204-I/TL

DSPIC33EP32MC204-I/TL - 16-bit 70 MIPS DSC 32KB Flash | Microchip

The Microchip Technology DSPIC33EP32MC204-I/TL is a 16-bit digital signal controller (DSC) from the dsPIC33EP family delivering 70 MIPS performance, 32KB (10.7K x 24) of Flash program memory, and a 44-pin VTLA (6x6 mm) QFN package with exposed pad. A digital signal controller combines the control peripherals of a microcontroller with the math acceleration of a digital signal processor in a single chip. In the semiconductor hierarchy, the dsPIC33EP sits under the digital signal controller category, which itself bridges general-purpose microcontrollers and dedicated DSPs, making it a natural choice for closed-loop control systems that also need real-time filtering or transform computation. Key features of the DSPIC33EP32MC204-I/TL include a 16-bit dsPIC DSC core with DSP engine, high-speed PWM modules purpose-built for motor control, DMA controller support, and multiple serial interfaces. The 32KB Flash array is organized as 10.7K x 24-bit instruction words, and the integrated DSP instructions enable efficient execution of FIR/IIR filters and PID loops without an external DSP. Architecturally, the dsPIC33E core supports a modified Harvard bus structure with a 16-bit data path, hardware multiplier, and accumulators suited to fixed-point arithmetic. The motor-control PWM peripherals provide complementary outputs with dead-time insertion, which is the defining feature of the MC (motor control) variant of this family. Typical applications include three-phase brushless DC (BLDC) and permanent magnet synchronous motor (PMSM) drives, as demonstrated in Microchip's official dsPIC33EP32MC204 Drone Propeller Reference Design, plus digital power supplies, sensors with onboard signal processing, and industrial automation nodes. Design consideration: the 44-pin VTLA package has an exposed thermal pad that must be soldered to a grounded copper pour for both electrical and thermal performance; verify the 6x6 mm footprint in your layout before switching from the TQFP-44 (10x10 mm) /PT variant, which is electrically equivalent but not footprint-compatible. This page synthesizes distributor pricing context, drop-in family alternatives, reference-design guidance, and selection notes not found together on the manufacturer datasheet.

询价 联系我们