微控制器

产品（20,000+)

PIC16HV610-I/ST - 8-Bit MCU 20MHz 1.75KB Flash | Microchip
PIC16HV610-I/ST

PIC16HV610-I/ST - 8-Bit MCU 20MHz 1.75KB Flash | Microchip

The Microchip Technology PIC16HV610-I/ST is an 8-bit PIC® 16F-family flash microcontroller with an integrated high-voltage shunt regulator, delivering 20MHz CPU performance from 1.75KB (1K x 14) of on-chip Flash program memory in a 14-pin TSSOP package. The "HV" prefix indicates a built-in 2.5V-15V shunt voltage regulator that allows the part to operate directly from high-voltage supplies — typically 3.5V to 15V — without an external regulator on the power pin. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash/ROM), data memory (RAM), and a fixed set of peripherals such as timers, comparators, ADCs, and I/O ports. PIC microcontrollers sit within the broader taxonomy of microcontroller -> embedded controller -> integrated circuit -> semiconductor. The PIC16HV610-I/ST belongs to Microchip's mid-range 14-bit instruction word PIC16 family, optimized for low-cost, deterministic embedded control. Key features include 64 bytes of RAM, 12 I/O pins, one 8-bit and one 16-bit timer, an analog comparator, and a 4-channel 10-bit ADC (per datasheet). The integrated high-voltage shunt regulator eliminates external components in mains-derived or battery-stack designs, making this device especially attractive for cost-sensitive white goods, lighting controls, and power-supply front-end controllers. In-system programming via ICSP supports field firmware updates. Typical applications include capacitive-touch user interfaces, LED lighting controllers, sensor signal conditioning, low-power remote controls, and primary-side regulation in AC/DC and DC/DC switch-mode power supplies. The wide operating voltage range (2.0V to 15V for logic) supports direct connection to rectified mains or to multi-cell battery stacks. For design considerations, ensure the shunt regulator current is properly derated for worst-case input voltage, and account for the ICSP/PGD/PGC pin sharing when laying out the PCB. This page synthesizes distributor pricing, parametric comparison with same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC16HV610T-I/ML - 1.75KB Flash 8-Bit MCU with Shunt Regulator | Microchip
PIC16HV610T-I/ML

PIC16HV610T-I/ML - 1.75KB Flash 8-Bit MCU with Shunt Regulator | Microchip

The Microchip Technology PIC16HV610T-I/ML is a 14-pin, Flash-based 8-bit CMOS microcontroller from the PIC16 family, integrating a high-voltage shunt regulator on-chip and housed in a QFN-16 package. Operating up to 20 MHz with 1.75 KB (1K x 14) of Flash program memory and 64 bytes of SRAM, it is engineered for cost-sensitive embedded control nodes that operate directly from a high-voltage rail without an external LDO. The 'HV' family integrates a parallel shunt regulator across the VDD pins, allowing the device to run from inputs as high as the absolute maximum VDD rating while dissipating excess voltage through an external Zener reference. A microcontroller (MCU) is an integrated circuit that combines a CPU core, non-volatile program memory (Flash or ROM), volatile data memory (RAM), and a configurable set of peripherals (timers, ADC, comparators, PWM, communication interfaces) into a single silicon die. The PIC16 mid-range core is one of the foundational 8-bit architectures in the Microchip portfolio, classed within the broader category of microcontrollers -> microcontrollers and microprocessors -> semiconductors -> integrated circuits. Flash-based variants allow in-system re-programming, which makes the PIC16HV610 well-suited for designs that must be firmware-updated in the field. Key features of the PIC16HV610 include a 10-bit ADC with 8 channels, one 8-bit and one 16-bit timer, an enhanced PWM module, an analog comparator with selectable reference, internal 4 MHz and 31 kHz oscillators, and 11 GPIO pins. The device supports in-circuit serial programming (ICSP) and runs across an industrial -40C to +85C temperature range, drawing only a few hundred microamps of quiescent current at low clock rates. The integrated shunt regulator enables direct battery-monitor and battery-stack powered designs that would otherwise require a discrete LDO, reducing BOM cost and PCB area. Typical applications for the PIC16HV610T-I/ML include battery chargers, multi-cell battery monitors, smoke and CO detectors, AC line-powered sensor interfaces, LED lighting controllers, small appliance control, and remote controls. Designers favor this part where a high-voltage supply is already present and a dedicated regulator would consume excessive quiescent current. The QFN-16 package provides a small footprint suitable for compact consumer and industrial products. When designing with this part, place a low-ESR decoupling capacitor close to each VDD pin and ensure the shunt Zener reference resistor is sized to carry worst-case load plus the MCU current at the chosen VDD target. The QFN exposed pad should be soldered to a copper pour to meet thermal and electrical ground requirements. This page combines datasheet-derived specifications, drop-in alternatives in the same QFN-16 footprint, and practical design notes not assembled on the standard distributor listing.

询价 联系我们
PIC16HV610T-I/ST - 8-bit MCU, 1.75KB Flash, 64B RAM, HV 15V | TSSOP-14 | Microchip
PIC16HV610T-I/ST

PIC16HV610T-I/ST - 8-bit MCU, 1.75KB Flash, 64B RAM, HV 15V | TSSOP-14 | Microchip

The Microchip Technology PIC16HV610T-I/ST is an 8-bit PIC RISC flash microcontroller in a 14-pin TSSOP package, featuring an integrated high-voltage shunt regulator that allows direct operation from supplies as high as 15V. It offers 1.75 KB of self-programmable flash program memory, 64 bytes of SRAM, 128 bytes of EEPROM, a 10-bit ADC, and 12 I/O pins. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, RAM, peripherals, and I/O. The PIC16HV610 belongs to the mid-range PIC16 family of 8-bit microcontrollers, characterized by an enhanced 14-bit instruction set, single-cycle hardware multiply (for select variants), and low-power nanoWatt technology. It sits in the hierarchy: 8-bit MCU -> PIC16 family -> mid-range core -> CMOS flash microcontroller -> embedded computing. This high-voltage variant eliminates external 5V regulators in 12V automotive and industrial applications. Key features include a maximum clock speed of 20 MHz, an internal 8 MHz oscillator, an enhanced PWM module, a comparator module, and a 10-bit ADC with up to 8 channels. The high-voltage shunt regulator eliminates the need for an external 5V LDO when the device is powered from 9V-15V rails, reducing BOM cost in automotive and industrial designs. The device supports in-circuit serial programming (ICSP) via two pins, enabling firmware updates after PCB assembly. The PIC16HV610 architecture employs a Harvard bus with separate program and data paths, a 14-bit instruction word, and an 8-level hardware stack. The flash program memory supports 100,000 erase/write cycles and 40-year retention typical. On-chip debug is available through the ICSP interface, allowing breakpoint-based development with Microchip's MPLAB X IDE and ICD debuggers. Typical applications include automotive body controllers, sensor signal conditioning, 12V-powered LED drivers, industrial control loops, and battery monitoring. The 15V shunt regulator input makes it ideal for direct connection to automotive 12V buses without external voltage translation. When designing with this device, ensure the shunt regulator current is sized for the worst-case load plus margin, and route the analog AVCC/DAC reference pins with ground isolation. The TSSOP-14 footprint is also pin-compatible with the standard-voltage PIC16F610 for 5V-only designs. This page synthesizes distributor pricing, drop-in alternatives within the PIC16F610/616/610/616 family, and practical design notes that are not duplicated on the manufacturer datasheet cover page.

询价 联系我们
PIC16HV616-E/ML - 8-Bit 20MHz MCU 3.5KB Flash | Microchip
PIC16HV616-E/ML

PIC16HV616-E/ML - 8-Bit 20MHz MCU 3.5KB Flash | Microchip

The Microchip Technology PIC16HV616-E/ML is an 8-bit Flash-based CMOS microcontroller from the PIC16 family, featuring 3.5KB (2K x 14) of Flash program memory, 128 bytes of RAM, and a maximum CPU clock of 20MHz in a 16-pin QFN (4x4 mm) exposed-pad package. It belongs to the PIC16F610/616/HV610/HV616 device group, distinguished by its integrated shunt regulator (HV suffix) that allows direct operation from high-voltage supplies up to 15V without an external LDO. A microcontroller (MCU) is a single-chip computer containing a processor core, non-volatile program memory, volatile data memory, and programmable I/O peripherals. The PIC16 family uses a RISC-based Harvard architecture with a 14-bit instruction word and is aimed at cost-sensitive embedded control. Within the PIC taxonomy, the PIC16HV616 sits below the PIC18 and dsPIC families in capability but above baseline PIC10/12 devices in peripheral integration. Microchip's mid-range 8-bit cores are widely deployed in appliance controls, sensor interfaces, lighting ballasts, and battery-powered nodes where deterministic real-time response and low quiescent current matter more than raw throughput. Key differentiating specifications include 3.5KB self-programmable Flash (100K erase/write cycles typical), 128 bytes SRAM, an internal 8MHz high-speed oscillator, an integrated 5-bit DAC and 10-bit ADC with up to 8 channels, two 8-bit timers plus one 16-bit timer, an enhanced PWM/Capture/Compare module, an on-chip voltage reference, and a unique shunt regulator capable of supplying the internal 3.3V logic from a 2V-15V supply rail. The integrated HV shunt eliminates an external LDO, reducing BOM cost and PCB area in 12V-15V industrial and automotive subsystems. Architecturally the device uses Microchip's enhanced mid-range core (49 instructions, 16-level hardware stack) with a 14-bit program word and 8-bit data path. The high-voltage shunt regulator uses a Zener-referenced pass element that clamps excess input voltage as heat, so thermal management at the exposed pad is important for HV variants. The ADC supports an internal bandgap reference plus an external Vref+ pin, and the comparator has a programmable on-chip reference for analog signal conditioning without external resistors. Typical applications include 12V-15V industrial sensor nodes, automotive courtesy and lighting modules, LED lighting ballasts, smoke and gas detector signal chains, white-goods control boards, and battery charging monitors. The wide VIN range and integrated shunt make the HV616 particularly useful wherever a regulated 3.3V rail is needed from a noisy or unregulated 12V bus. When designing with this device, place a low-ESR ceramic bypass cap directly on VDD and use a low-impedance trace on the shunt shunt to the input rail. The exposed thermal pad must be soldered to a sufficiently large copper pour to dissipate the shunt regulator's power loss; expect roughly (VIN - 3.3V) x ISHUNT of heat that must flow through the PCB. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC16HV616-E/P - 8-Bit MCU, 3.5KB Flash, 20MHz | Microchip
PIC16HV616-E/P

PIC16HV616-E/P - 8-Bit MCU, 3.5KB Flash, 20MHz | Microchip

The Microchip Technology PIC16HV616-E/P is an 8-bit PIC RISC microcontroller featuring 3.5KB Flash program memory, 128 bytes RAM, and an integrated high-voltage shunt regulator, all housed in a 14-pin PDIP through-hole package. It operates at up to 20MHz clock speed with a 14-bit instruction set, 35 instructions, and supports operating voltages of 2.0V to 5.5V with the HV variant enabling direct connection to 3.5V-15V supplies. A microcontroller (MCU) is a single-chip computer containing a CPU, memory (Flash/RAM/EEPROM), and programmable I/O peripherals. The PIC16HV616 belongs to Microchip's PIC16 mid-range family, positioned in the taxonomy: PIC16HV616 -> PIC16F616 (low-voltage cousin) -> PIC16F family -> 8-bit PIC -> PIC microcontroller -> MCU -> embedded processor. The HV prefix denotes the integrated shunt voltage regulator that lets the device operate directly from higher-voltage buses. Key features include 12 I/O pins, an 8-channel 10-bit ADC, two comparators, enhanced PWM module, and an internal 8MHz oscillator. The integrated HV shunt regulator eliminates the need for an external 5V LDO when powered from 12V or higher rails - a significant BOM cost and board-space saver in cost-sensitive designs. The device also includes nanoWatt power management for low-power sleep modes down to sub-microamp currents. Architecturally, the PIC16HV616 uses a Harvard RISC core with separate program and data buses, allowing simultaneous instruction fetch and operand access in a single cycle (except for branches). The high-voltage shunt regulator is implemented as a parallel (shunt) element rather than a series LDO, providing robust overvoltage tolerance at the cost of continuous quiescent dissipation. This topology suits battery charging, LED string driving, and other applications where a series regulator is impractical. Typical applications include 12V LED lighting controllers, battery management, capacitive-touch user interfaces, motor control loops, and low-cost consumer appliances. The wide input voltage tolerance and small footprint make it ideal for distributed nodes in industrial sensor networks. When designing with this device, verify the shunt regulator's power dissipation budget (VIN - 5V) * I_LOAD + I_QUIESCENT, since the shunt element must sink the worst-case excess current while keeping the regulated rail within tolerance.

询价 联系我们
PIC16HV616-E/SL - 8-Bit 20MHz MCU 3.5KB Flash HV | Microchip
PIC16HV616-E/SL

PIC16HV616-E/SL - 8-Bit 20MHz MCU 3.5KB Flash HV | Microchip

The Microchip Technology PIC16HV616-E/SL is an 8-bit Flash-based CMOS microcontroller with an integrated shunt regulator, designed for high-voltage (HV) operation directly from battery or rectified mains rails. It features 3.5KB (2K x 14) of Flash program memory, 128 bytes of RAM, and operates at up to 20 MHz across an industrial temperature range. The device is housed in a 14-pin SOIC (SL) package and is part of the PIC16HV616 mid-range MCU family with on-chip high-voltage support. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable I/O peripherals. The PIC16HV616 belongs to the broader category of 8-bit microcontrollers, sitting under the hierarchy of embedded microcontrollers, microprocessors, and finally semiconductors. The 'HV' family is a specialized subset that includes an internal shunt regulator, allowing direct connection to unregulated high-voltage DC supplies without an external LDO - a feature that simplifies power supply design in cost-sensitive applications. Key features include an internal 8 MHz high-speed oscillator with PLL option to reach 20 MHz, a 10-bit Analog-to-Digital Converter (ADC) with up to 8 channels, dual comparators, and a 16-bit PWM module. The integrated shunt regulator supports supply voltages up to 15V, eliminating the need for an external voltage regulator in many designs. Additional peripherals include an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), I2C/SPI, and a 16-bit timer with capture/compare. The PIC16HV616's enhanced mid-range core delivers 49 instructions with 16-level hardware stack and interrupt capability. The architecture provides deterministic instruction execution of 200 ns per instruction at 20 MHz, making it suitable for real-time control loops. The internal oscillator calibration eliminates external crystals in many designs, reducing BOM cost and PCB area. The 14-bit instruction word and Harvard architecture separate program and data memory paths for predictable real-time response. Typical applications include LED lighting drivers, battery chargers, motor control in small appliances, smart sensor nodes, and industrial control modules. The wide operating voltage range makes it particularly suitable for 12V automotive, 24V industrial, and offline rectified supplies where an integrated regulator simplifies design. Designers also use the PIC16HV616 in capacitor discharge circuits and energy-harvesting systems that require direct HV input capability. When designing with this part, note that the shunt regulator dissipates excess voltage as heat - at 15V supply and 10 mA load, expect up to 150 mW dissipation that must be accounted for in thermal calculations. The 14-pin SOIC package provides 12 GPIO pins with multiplexed peripheral functions, allowing flexible pin assignments but requiring careful peripheral-to-pin mapping during firmware development. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet, providing engineers with a single source for selection, sourcing, and design-in guidance for the PIC16HV616-E/SL.

询价 联系我们
PIC16HV616-I/P - 8-bit MCU 3.5KB Flash 20MHz | Microchip
PIC16HV616-I/P

PIC16HV616-I/P - 8-bit MCU 3.5KB Flash 20MHz | Microchip

The Microchip Technology PIC16HV616-I/P is an 8-bit RISC flash microcontroller with integrated high-voltage shunt regulator support, packaged in a 14-pin PDIP through-hole format. The device features 3.5KB (2K x 14) of Flash program memory, 128 bytes of RAM, and executes instructions at speeds up to 20MHz, delivering up to 5 MIPS of throughput. The 'HV' suffix denotes the high-voltage variant that includes an internal shunt regulator suitable for applications operating directly from a 3.5V to 15V supply without external regulation. What is a PIC microcontroller? A PIC (Peripheral Interface Controller) microcontroller is a family of 8/16/32-bit RISC-based microcontrollers from Microchip Technology built on a Harvard architecture with separate program and data buses. Within the PIC taxonomy, the PIC16HV616 belongs to the mid-range PIC16F family, which provides a balance of cost, peripheral integration, and code efficiency for embedded control tasks. Key features include 12 I/O pins, three timers, two analog comparators, a 10-bit PWM module, a 10-bit ADC, Brown-Out Detect (BOD), Power-On Reset (POR), and a Watchdog Timer (WDT). The integrated high-voltage shunt regulator allows direct connection to unregulated 12V supplies, simplifying power architecture in appliance and industrial applications. The PIC16HV616 uses a 14-bit instruction word with a RISC instruction set optimized for C and assembly code density. Its nanoWatt technology provides flexible power management with multiple idle and sleep modes, enabling extended battery life in low-duty-cycle applications. The internal oscillator reduces BOM cost by eliminating the need for external clock components in many designs. Typical applications include LED lighting controls, battery chargers, SMPS primary-side control, fan speed controllers, small appliance controls, and battery-powered sensor interfaces. The high-voltage capability makes it especially suitable for 12V-24V system designs where a separate regulator would otherwise be required. When designing with this device, ensure the shunt regulator configuration matches the supply voltage range. The internal shunt regulator requires proper sizing of the external dropping resistor to limit current at minimum VIN. Refer to the Microchip datasheet 41288F for shunt regulator application circuits and thermal considerations. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes not found on any single distributor page, helping engineers evaluate the PIC16HV616-I/P against same-package drop-in equivalents and cross-family alternatives.

询价 联系我们
PIC16HV616-I/ST - 8-Bit 20MHz MCU 4KB Flash | TSSOP-14
PIC16HV616-I/ST

PIC16HV616-I/ST - 8-Bit 20MHz MCU 4KB Flash | TSSOP-14

The Microchip Technology PIC16HV616-I/ST is an 8-bit Flash-based CMOS microcontroller in a 14-pin TSSOP package, featuring an integrated shunt regulator that allows direct operation from a 2V to 5V supply without a separate voltage regulator. The device integrates 4KB (2K x 14 words) of Flash program memory, 128 bytes of RAM, and 256 bytes of EEPROM, with a 20MHz internal oscillator and Microchip's enhanced mid-range core with 35 instructions and 8 stack levels. Its peripheral set includes a user-configurable comparator with hysteresis, an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), an MSSP module supporting SPI and I2C, up to 11 I/O pins with 25mA source/sink capability, and an internal 4/8MHz oscillator selectable via configuration bits. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable I/O peripherals on one die. The PIC16HV616 belongs to the Microchip PIC16 enhanced mid-range family, which sits in the 8-bit microcontrollers -> microcontrollers -> embedded ICs -> integrated circuits taxonomy and is widely deployed for low-cost, low-power deterministic control. The HV suffix denotes the integrated shunt regulator that converts a wide input voltage to the chip's internal logic supply. Key differentiating specifications include the on-chip shunt regulator (eliminating the need for an external LDO in many battery and bus-powered applications), 25mA high-current I/O for direct LED or relay driving, the user-configurable comparator with internal reference and hysteresis, and a wide supply range of 2.0V to 5.5V. The 8-bit Enhanced Mid-Range core delivers deterministic interrupt response and single-cycle instruction execution on this device family. Typical applications include LED lighting controllers, battery chargers, sensor signal conditioning, simple sensor nodes, and low-power IoT endpoints where the integrated shunt regulator simplifies the power tree. The high-current 25mA I/O also makes the part attractive for driving LEDs, relays, or small solenoids directly without external driver transistors. According to the manufacturer datasheet, the PIC16HV616 family is part of Microchip's enhanced mid-range 8-bit portfolio optimized for cost-sensitive embedded control. When designing with this part, ensure the shunt regulator resistor RVDD is sized to provide at least 5mA of bias current (typically 100kohm to VDD) and to limit shunt current under worst-case input voltage conditions. The comparator output can be routed internally to timers for advanced capture/compare functions, eliminating external glue logic. This page synthesizes distributor pricing, drop-in TSSOP-14 alternatives, and practical design notes not found in the standalone manufacturer datasheet.

询价 联系我们
PIC16HV616T-I/ML - 8-bit MCU, 20MHz, 3.5KB Flash, 16-QFN | Microchip
PIC16HV616T-I/ML

PIC16HV616T-I/ML - 8-bit MCU, 20MHz, 3.5KB Flash, 16-QFN | Microchip

The Microchip Technology PIC16HV616T-I/ML is an 8-bit RISC microcontroller IC with 20 MHz CPU speed, 3.5 KB (2K x 14) of Flash program memory and 128 bytes of RAM, housed in a 16-pin QFN (4x4 mm) package with industrial temperature grade (-40C to +85C). It belongs to Microchip's PIC16HV616 family, the "HV" prefix denoting an integrated high-voltage shunt regulator that allows direct operation from a 2V to 5V supply without an external regulator, simplifying low-power and battery-fed designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, peripherals and I/O on one silicon die. Within the broader taxonomy, the PIC16HV616 sits at: PIC microcontroller -> mid-range 8-bit PIC -> enhanced mid-range core -> embedded microcontroller -> semiconductor IC. Its RISC (Reduced Instruction Set Computer) Harvard architecture separates program and data buses, allowing simultaneous instruction fetch and data access for deterministic 20 MHz throughput. Key features that distinguish this part include 12 I/O pins with interrupt-on-change support, an internal 8 MHz oscillator (calibrated for +/-1% accuracy), 10-bit ADC with up to 8 channels, two 8-bit timers plus a 16-bit timer, an enhanced PWM module with complementary outputs, an analog comparator with rail-to-rail inputs, and the on-chip HV shunt regulator. Memory endurance is rated at 100K erase/write cycles and data EEPROM retention is 40 years minimum. Typical applications include low-power battery chargers, LED lighting drivers, smoke detectors, remote controls, smart sensors, and IoT edge devices that need a few pins and a small footprint. The 4x4 mm QFN package is footprint-compatible with other PIC16F6xx family members, easing PCB migration between pin-counts. When designing with this device, ensure that the GP3/MCLR pin is correctly biased (internal pull-up enabled by default) and that unused I/O are configured as outputs to minimize sleep current. Decoupling VDD with a 0.1 uF ceramic capacitor placed within 3 mm of the pin is required for ADC accuracy. This page synthesizes distributor pricing, application guidance and drop-in alternative analysis not found in the standalone Microchip datasheet, providing engineers with a single reference for sourcing and substitution decisions.

询价 联系我们
PIC16HV616T-I/ST - 8-bit MCU 3.5KB Flash 20MHz HV | Microchip
PIC16HV616T-I/ST

PIC16HV616T-I/ST - 8-bit MCU 3.5KB Flash 20MHz HV | Microchip

The Microchip PIC16HV616T-I/ST is a flash-based 8-bit CMOS microcontroller with an integrated shunt regulator, packaged in a 14-pin TSSOP. It delivers 3.5KB (2K x 14) of Flash program memory, 128 bytes of RAM, and 12 I/O pins, while operating from an internal 8 MHz oscillator that can be software-tuned up to 20 MHz instruction throughput. The 'HV' (high-voltage) silicon supports direct operation from loosely regulated or unregulated supplies up to 15 V nominal via an internal Zener-shunt regulator, eliminating the need for an external regulator in simple power-supply-fed designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash/ROM), working RAM, peripherals, and I/O on one die. PIC microcontrollers use a modified Harvard RISC architecture: program memory is accessed on a separate bus from data memory, allowing instruction fetch and operand read in a single cycle. The PIC16 family sits in the entry-level tier of Microchip's 8-bit line, balancing low cost, low power, and deterministic interrupt latency for cost-sensitive embedded control. PIC MCUs are widely used in white goods, sensor signal conditioning, lighting controls, and battery management front-ends. Key features of the PIC16HV616T-I/ST include the NanoWatt XLP (eXtreme Low Power) technology, an internal 8 MHz precision oscillator (factory calibrated to +/-1 percent typical), a 10-bit ADC with up to 8 channels, two 8-bit timers and one 16-bit timer, an enhanced PWM/capture/compare module, and an on-chip shunt regulator that allows direct connection to high-voltage buses. The device also integrates an 8 MHz internal RC, a comparator, and supports in-circuit serial programming (ICSP) via two pins. Operating voltage spans 2.0 V to 5.5 V on the regulated logic rail, with the HV shunt regulator handling the higher supply levels. The PIC16HV616T-I/ST is typically used in appliance controls, power-supply front ends, smart battery chargers, LED lighting drivers, and industrial sensor interface boards. Its 12 I/O and 3.5KB Flash comfortably support state-machine designs, simple PWM loops, and slow-protocol slave implementations. The combination of TSSOP-14 small footprint and integrated shunt regulator reduces BOM cost versus PIC16F616 designs that need an external LDO. When designing with this part, derate the shunt regulator dissipation carefully: at VIN = 12 V and 5 mA logic current, the regulator absorbs roughly 60 mW, which is fine for TSSOP copper but demands a copper-pour heat-spreader above 25 mA. Always add a series resistor on the HV pin to set shunt current, and provide a low-ESR bypass of at least 0.1 uF on VDD.

询价 联系我们
PIC16HV753-E/ML - 8-bit MCU, 3.5KB Flash, 20MHz, HV Shunt | Microchip
PIC16HV753-E/ML

PIC16HV753-E/ML - 8-bit MCU, 3.5KB Flash, 20MHz, HV Shunt | Microchip

The Microchip Technology PIC16HV753-E/ML is an 8-bit PIC16-family Flash microcontroller with integrated high-voltage shunt regulator, offering 3.5KB (2K x 14) of self-read/write Flash program memory, 128 bytes of SRAM, and a 16-QFN (4x4) package rated for the -40C to +125C extended industrial temperature range. The part executes instructions from a 14-bit word, runs up to 20MHz from the internal 8MHz oscillator with PLL multiplication, and integrates peripherals tailored for power-conversion and analog-control loops. What is a PIC16 Mid-Range microcontroller? The PIC16 mid-range family is a category of 8-bit RISC microcontrollers from Microchip Technology using a 14-bit instruction set. It occupies the middle tier of Microchip's PIC microcontroller portfolio - above the baseline PIC10/12/14/16 baseline (12-bit) and below the PIC18 enhanced (16-bit) architecture - and is widely used in cost-sensitive embedded designs where deterministic timing, low power, and integrated analog peripherals matter more than raw throughput. Key features of the PIC16HV753-E/ML include an internal 8MHz oscillator (with PLL), one op-amp, two high-speed analog comparators with 50ns propagation delay, one Capture/Compare/PWM (CCP) module, eight 10-bit ADC channels with internal voltage reference, and a 9-bit DAC. The 'HV' in the part number designates the integrated high-voltage shunt regulator that allows operation directly from a high-voltage rail, eliminating the need for an external low-dropout regulator. The device is built on CMOS technology and uses the standard PIC mid-range core. Its 35 instruction set with 200ns instruction cycle at 20MHz yields predictable, deterministic timing for motor control and power-supply loop tasks. The 16-QFN EP package includes an exposed thermal pad that must be soldered to the PCB ground plane to meet the datasheet's thermal specifications. Typical applications include LED lighting drivers, battery chargers, smart battery packs, power-supply primary-side controllers, motor-control signal conditioning, and industrial sensor transmitters. The 'HV' shunt regulator allows the MCU to be powered from a 2V to a much higher DC bus after a current-limiting resistor, simplifying isolated and non-isolated SMPS designs. When designing with this part, ensure the exposed pad on the QFN package is soldered to a sufficient copper pour (typically 1 square inch of 2oz copper) to keep junction temperature within safe limits. Verify that the high-voltage shunt regulator's input current limit resistor is sized for worst-case VIN, since excessive dissipation in this resistor can exceed package ratings. This page synthesizes distributor pricing, same-package drop-in alternatives (including the automotive-screened PIC16HV753-E/MLVAO and the legacy PIC16F753-E/ML), and practical design notes not consolidated on any single distributor page.

询价 联系我们
PIC16HV753-E/P - 8-bit MCU, 3.5KB Flash, HV Shunt | Microchip
PIC16HV753-E/P

PIC16HV753-E/P - 8-bit MCU, 3.5KB Flash, HV Shunt | Microchip

The Microchip Technology PIC16HV753-E/P is an 8-bit PIC16 microcontroller featuring 3.5KB (2K x 14) of Flash program memory, 128 bytes of RAM, and an integrated high-voltage shunt regulator, housed in a 14-pin PDIP (0.300 inch, 7.62mm) through-hole package. It operates from 2.0V to a regulated 5V internal supply derived from the on-chip HV shunt regulator accepting inputs up to 13.5V typical, with 20 MHz CPU performance from a 32 MHz internal oscillator and 4 PWM channels plus a 9-bit DAC. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash/RAM), and programmable peripherals. The PIC16HV753 belongs to the PIC16F family of 8-bit RISC microcontrollers, which sit in the broader hierarchy of embedded microcontrollers -> microprocessors -> semiconductors. The 8-bit RISC Harvard architecture executes most instructions in a single clock cycle, simplifying deterministic timing for control applications. Key features include 12 ADC channels with 10-bit resolution, four hardware PWM outputs, a 9-bit DAC, two comparators, a high-voltage shunt regulator for direct connection to 12V battery rails, and Enhanced Mid-Range Core with 49 instructions plus 16-level hardware stack. The integrated HV shunt eliminates the need for external regulation when powered from unregulated DC sources. The PIC16HV753-E/P uses an Enhanced Mid-Range 8-bit core built on Microchip's proprietary process, supporting in-circuit serial programming (ICSP) via two pins and self-programmable Flash for bootloader-style firmware updates. The HV shunt regulator provides a regulated 3.3V or 5V supply to internal logic, enabling direct connection to 12V lead-acid or similar unregulated rails without an external LDO. Typical applications include battery charging controllers, LED drivers, DC-DC converters, 12V industrial sensors, and consumer appliance controls where the high-voltage shunt simplifies the power tree and reduces external components. When designing with this part, configure the MCLR pin as input by tying it through a resistor to VDD to avoid unintentional resets in noisy environments, and provide adequate decoupling (100nF) close to the VDD pin. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC16HV753-E/ST - 8-Bit MCU, 3.5KB Flash, 20MHz, 14-TSSOP | Microchip
PIC16HV753-E/ST

PIC16HV753-E/ST - 8-Bit MCU, 3.5KB Flash, 20MHz, 14-TSSOP | Microchip

The Microchip PIC16HV753-E/ST is an 8-bit PIC16F-family flash microcontroller featuring 3.5KB (2K x 14 words) of program memory, 128 bytes of SRAM, and an integrated high-voltage shunt regulator, housed in a 14-pin TSSOP package. According to the manufacturer datasheet, the device operates from an internal 8MHz oscillator (with selectable 31kHz LF oscillator), supports up to 20MHz instruction execution, and integrates a 9-bit DAC, internal voltage reference, comparators, ADC, and CCP/PWM peripherals for mixed-signal embedded designs. What is an 8-bit PIC microcontroller? An 8-bit PIC (Peripheral Interface Controller) is a Harvard-architecture RISC microcontroller from Microchip Technology whose ALU and data paths are 8 bits wide. The PIC16F family is the mid-range tier within this hierarchy (PIC -> PIC16 -> PIC16HV753), optimized for low-cost, low-power mixed-signal embedded control in industrial, consumer, and automotive sensor-interface applications. The PIC16HV753 adds an integrated shunt regulator, allowing direct operation from high-voltage rails (up to 15V nominal). Key features of the PIC16HV753 include nanoWatt XLP extreme-low-power technology with <50 nA sleep current, a 9-bit DAC for bias or trim voltages, two rail-to-rail comparators with programmable references, a 10-bit ADC with up to 8 channels, and integrated mTouch capacitive-sensing support. The internal shunt regulator eliminates the need for an external 3.3V or 5V LDO when the device is powered from industrial 12V or 24V rails, reducing BOM and PCB area. The PIC16HV753 uses a 14-bit instruction word and a RISC pipeline, providing deterministic interrupt response and predictable execution timing critical for sensor sampling and motor control loops. Enhanced mid-range core features include a hardware stack, table reads/writes to Flash, and a wide operating voltage range enabled by the internal shunt regulator. The high-voltage shunt operates with external resistors on a wide input voltage range, ideal for distributed sensor nodes. Typical applications include battery chargers, LED lighting controllers, smart sensor nodes, industrial 4-20mA loop powered devices, and consumer appliance control. The shunt regulator makes the PIC16HV753 particularly well suited for direct connection to 12V automotive or industrial buses without an external voltage regulator stage. When designing with this device, ensure the shunt resistor is sized correctly for the expected input voltage range and load current. Program memory is self-programmable via ICSP, and debugging is supported through the ICD 3 toolchain. Pin-compatible PIC16F753 variants without the shunt regulator are drop-in alternatives for designs that already use external regulation.

询价 联系我们
PIC16HV753-I/ML - 8-bit MCU 20MHz 3.5KB Flash 16-QFN | Microchip
PIC16HV753-I/ML

PIC16HV753-I/ML - 8-bit MCU 20MHz 3.5KB Flash 16-QFN | Microchip

The Microchip Technology PIC16HV753-I/ML is an 8-bit RISC PIC16 microcontroller operating up to 20 MHz, integrating 3.5 KB (2K x 14) of self-read/write FLASH program memory and 128 bytes of RAM in a 16-pin QFN (4x4 mm) package. The "HV" family variant includes a built-in shunt (High-Voltage) regulator that allows direct operation from a high-voltage supply up to 15 V without an external LDO, while the standard PIC16F753 variant requires a regulated 2.0-5.5 V supply. The part is qualified over the industrial -40C to +85C temperature range. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, data RAM, and on-chip peripherals such as timers, ADC, communication interfaces, and GPIO. The PIC16 mid-range core is one of Microchip's classic 8-bit architectures using a 14-bit instruction word optimized for deterministic interrupt response and low-power operation. The PIC16HV753 sits inside the broader hierarchy: 8-bit MCU -> microcontroller -> embedded IC -> semiconductor device, and is the PIC family member optimized for high-voltage direct-supply applications like LED lighting, battery chargers, and motor control where eliminating an external regulator saves cost and board area. Key features include an 8-channel 10-bit ADC, a 9-bit DAC, two high-speed analog comparators (50 ns response), an op-amp module, one Capture/Compare/PWM (CCP) peripheral, and a 32 kHz-to-20 MHz internal oscillator with 8 MHz factory calibration. The device also provides enhanced PWM, multiple timers, a watchdog timer, an on-chip voltage reference, and in-circuit serial programming (ICSP) via two pins. High-voltage variants integrate a 15 V shunt regulator on the supply pin so the chip can be powered directly from 9 V or 12 V rails. Architecturally, the PIC16HV753 uses a Harvard RISC core with separate program and data buses, allowing instruction fetch and operand access in a single cycle. The high-voltage analog front-end is decoupled from the digital core through an internal regulator that generates the 2.0-5.5 V supply used by the core logic, giving designers a single-chip solution for direct-supply, mixed-signal embedded control. Typical applications include AC mains-powered LED lighting drivers, switch-mode power supply (SMPS) primary-side control, sealed lead-acid battery chargers, 12 V fan/motor controllers, and industrial sensor signal conditioning where the on-chip op-amp, comparators, and ADC provide a complete analog front-end without external analog ICs. When designing with this device, ensure the high-voltage supply current does not exceed the shunt regulator's load capability (typically a few mA) and place a 0.1 uF + 10 uF decoupling network close to the VDD pin. For in-circuit programming, dedicate the ICSPCLK/ICSPDAT pins and protect them from contention with application circuitry. This page synthesizes distributor pricing, drop-in PIC16 family alternatives, application reference designs, and practical design notes not collected in the manufacturer datasheet alone.

询价 联系我们
PIC16HV753-I/P - 8-Bit MCU, 3.5KB Flash, HV Shunt Reg | Microchip
PIC16HV753-I/P

PIC16HV753-I/P - 8-Bit MCU, 3.5KB Flash, HV Shunt Reg | Microchip

The Microchip Technology PIC16HV753-I/P is an 8-bit PIC16-family RISC microcontroller with an integrated high-voltage shunt regulator, packaged in a 14-pin PDIP (0.300", 7.62 mm) through-hole package. It delivers up to 20 MHz CPU performance, contains 3.5 KB (2K x 14) of Flash program memory, 128 bytes of RAM, and integrates a 9-bit Digital-to-Analog Converter (DAC) plus an internal 8 MHz oscillator. The integrated shunt regulator allows direct operation from high-voltage rails (typically 2V to user-defined VDD up to a user-programmable limit) without an external regulator, simplifying isolated or battery-stack designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory and peripherals on one die. The PIC16 family belongs to the RISC (Reduced Instruction Set Computer) class of 8-bit microcontrollers; in the broader product taxonomy, MCUs sit inside embedded microcontrollers, which sit inside microprocessors, which sit inside semiconductor ICs. The 'HV' in the part number indicates the high-voltage shunt-regulator feature, which in the broader power management hierarchy corresponds to a linear regulator function co-integrated with the digital logic. Key differentiating features include nanoWatt XLP technology for ultra-low power consumption, 9-bit DAC with internal bandgap reference, 4-channel 10-bit ADC, enhanced Capture/Compare/PWM (ECCP) module, and integrated shunt regulator for direct high-voltage operation. The 14-pin PDIP package offers ease of prototyping and breadboarding compared to surface-mount variants. The PIC16HV753's architecture combines a 14-bit instruction word with a Harvard bus, providing deterministic interrupt response and compact code density. The 9-bit DAC can be operated in 5-bit, 7-bit or 9-bit resolution modes and supports ramp generation for closed-loop control. Internal peripherals include up to 11 I/O pins, two 8-bit timers, one 16-bit timer, and an Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART) for serial communication. Typical applications include LED drivers and lighting control, battery charging management, sensor signal conditioning, low-power remote sensors, and industrial control loops. The internal shunt regulator enables direct 12V or 24V industrial-rail operation in a single chip. When designing with this part, note that the shunt regulator dissipates excess voltage as heat; ensure adequate PCB copper or thermal relief at the VDD/REG pin. The PDIP package supports easy in-circuit programming via the ICSP interface but consumes more board area than SOIC-14 or QFN-16 alternatives. This page synthesizes distributor pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet alone, providing engineering-grade context for sourcing and design decisions.

询价 联系我们
PIC16HV753-I/SL - 8-Bit MCU 20MHz 3.5KB Flash 14-SOIC | Microchip
PIC16HV753-I/SL

PIC16HV753-I/SL - 8-Bit MCU 20MHz 3.5KB Flash 14-SOIC | Microchip

The Microchip Technology PIC16HV753-I/SL is a high-voltage 8-bit RISC PIC16 microcontroller built on a CMOS process, integrating an internal shunt regulator that allows direct operation from a high-voltage supply (typically up to 15V regulated from higher rails). The device delivers 20 MHz instruction execution from 3.5 KB (2K x 14) of flash program memory and 128 bytes of data RAM, housed in a 14-pin SOIC (SL) industrial-temperature (-40C to +85C) package. A PIC microcontroller is a compact, low-power embedded controller that combines a CPU core, non-volatile flash memory for program storage, volatile RAM for data, and a rich mix of peripherals (ADC, timers, PWM, comparators, communication ports) on a single die. Within the broader taxonomy, the PIC16HV753 belongs to the PIC16F/HV family of mid-range 8-bit microcontrollers, itself a subcategory of embedded microcontrollers, which fall under integrated circuits for power management and control. The mid-range PIC16 core uses a 14-bit instruction word optimized for deterministic, single-cycle execution. Key features of the PIC16HV753 include 35 KB of total flash (using the same flash cell as the F-variant, of which 3.5 KB is available to user code), an internal 8 MHz high-precision oscillator, hardware 9-bit DAC, multiple 10-bit PWM modules, configurable logic cells, and on-chip comparators. The internal shunt regulator eliminates the need for an external 5V LDO in many high-voltage applications, simplifying the BOM. The industrial temperature grade (-40C to +85C) makes the part suitable for harsh-environment deployments. In circuit terms, the HV753 integrates its own high-voltage regulator so that downstream analog and digital blocks operate from a clean, internally regulated rail regardless of upstream supply variation between 2V and the user-set VDDIO. The 9-bit DAC and op-amp peripherals support analog signal generation and conditioning without external components. Typical applications include LED lighting controllers with analog dimming, battery chargers for portable systems, intelligent battery management, power-conversion feedback loops, and consumer/industrial control nodes. The wide operating voltage and integrated regulator cut part count versus discrete MCU + LDO designs. When designing with the PIC16HV753, ensure the shunt regulator current limit is configured correctly using the internal resistor divider and that decoupling SL holds at 100 nF plus 10 uF bulk placed within 5 mm of VDD. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC16HV753-I/ST - 8-Bit 20MHz MCU 3.5KB Flash 14-TSSOP | Microchip
PIC16HV753-I/ST

PIC16HV753-I/ST - 8-Bit 20MHz MCU 3.5KB Flash 14-TSSOP | Microchip

The Microchip Technology PIC16HV753-I/ST is an 8-bit flash-based CMOS microcontroller built on the enhanced PIC16 mid-range core, offering 3.5 KB of program Flash, 128 bytes of RAM, and an integrated high-voltage shunt regulator that permits direct operation from supply rails up to 15 V without external regulation. Housed in a 14-pin TSSOP package, it operates at up to 20 MHz instruction rate, integrates a 9-bit DAC, an internal 8 MHz oscillator, and supports a wide 2.0 V to user-defined operating range thanks to the integrated high-voltage shunt. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and a rich set of on-chip peripherals such as timers, ADC/DAC, communication interfaces, and I/O. The PIC16 family sits in the 8-bit microcontroller category within the broader semiconductor device taxonomy (8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC). The PIC16HV753 specifically belongs to the high-voltage sub-family, distinguished by an internal shunt regulator that allows direct connection to high-voltage rails. Key features include 3.5 KB self-programmable Flash program memory with 2K x 14 organization, 128 bytes SRAM, 8-level hardware stack, internal 8 MHz oscillator (factory calibrated to +/-1%), 9-bit DAC module with 5-bit comparator, 10-bit ADC, two 8-bit timers (TMR0/TMR2) and one 16-bit timer (TMR1), enhanced PWM with dedicated timer, I2C/SPI (MSSP) and AUSART (EUSART) serial interfaces, and 11 general-purpose I/O pins. The integrated shunt regulator accepts VIN up to 15 V, removing the need for external regulator ICs. The enhanced mid-range core adds hardware multiply, context-saving interrupts, and a hardware stack capable of 8-level deep call nesting. Debug support via ICD and an on-chip in-circuit debugger interface is included. The high-voltage shunt regulator with feedback loop provides low-cost digital programmability and stable system voltage reference, allowing the MCU to replace analog regulator functions in simple closed-loop systems. Typical applications include AC line-voltage sensing and control, lighting ballast control, battery chargers, smart fan/motor control with back-EMF sensing, and simple closed-loop constant-current/constant-voltage (CC/CV) converters where the shunt regulator and 9-bit DAC combine to form a complete digital power-supply controller. When designing with this device, mind the thermal envelope of the shunt regulator. The shunt dissipates (VIN - VDD) * ISHUNT continuously; at 12 V VIN with the internal regulator dropping 10 V at 20 mA load, dissipation is 200 mW, well within TSSOP ratings. Use bulk capacitance on the HV input and follow datasheet layout notes to avoid regulator instability. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC16HV753T-I/SL - 8-Bit MCU 3.5KB Flash HV Shunt | Microchip
PIC16HV753T-I/SL

PIC16HV753T-I/SL - 8-Bit MCU 3.5KB Flash HV Shunt | Microchip

The Microchip PIC16HV753T-I/SL is an 8-bit PIC16-family RISC microcontroller with 3.5KB Flash program memory, integrated high-voltage shunt regulator, and 14-pin SOIC package (SO-14/SL suffix) supplied on tape and reel. It belongs to the PIC16F753/HV753 device family and operates from a wide 2.0V to 5.5V VDD range, with the HV (high-voltage) variant supporting input rails up to 15V through its on-chip shunt regulator. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash/ROM), data memory (RAM), and a rich set of peripherals such as timers, ADC, comparators, and communication interfaces. The PIC16 HV family specifically targets applications where the MCU can derive its own low-voltage supply directly from a high-voltage DC bus (such as 12V or 15V) using only an external series resistor and a small decoupling capacitor. Within the broader taxonomy, the PIC16HV753 sits inside the 8-bit PIC16 architecture, itself a member of Microchip's mid-range PIC microcontroller family, used widely in cost-sensitive embedded control. Key features include a 20 MHz internal oscillator, 12-bit ADC with internal voltage reference, two operational amplifiers/comparators, a 9-bit DAC, enhanced PWM module, and zero-crossing detection. The device integrates a 5.1V shunt regulator that allows direct connection to 12V battery rails typical in automotive and industrial control without an external LDO, simplifying BOM and reducing board area. The PIC16HV753 uses a Harvard RISC architecture with a 14-bit instruction word, single-cycle execution except for branches, and a hardware stack of 16 levels. Its nanopower technology offers ultra-low sleep currents, making it well suited for battery-backed or energy-harvesting designs that spend long periods in standby and wake periodically. Typical applications include LED lighting controllers, battery management, smart shunt regulators, 12V automotive body modules, AC line voltage monitoring, capacitive touch front-ends, and compact DC-DC converter control. The wide Vin range plus analog-rich peripherals make it especially attractive for analog-loop control loops where most competing MCUs need external ADCs. When designing with this part, observe the absolute maximum VDD of 5.5V on the regulated rail; the HV front end can accept higher voltages but the shunt regulator must dissipate the excess power. Always size the external series resistor to limit shunt current below the package's thermal limits during worst-case line conditions. This page synthesizes distributor pricing, drop-in alternatives, and design notes that complement the Microchip datasheet for faster BOM and sourcing decisions.

询价 联系我们
PIC16HV753T-I/ST - 3.5KB Flash 8-bit MCU w/ Shunt Reg | Microchip
PIC16HV753T-I/ST

PIC16HV753T-I/ST - 3.5KB Flash 8-bit MCU w/ Shunt Reg | Microchip

The Microchip PIC16HV753T-I/ST is an 8-bit PIC® RISC microcontroller with integrated shunt regulator, 3.5KB Flash program memory, 128 bytes RAM, and a 9-bit DAC, housed in a 14-pin TSSOP package. It runs up to 20MHz instruction cycle from a wide 2.0V-5.5V supply and integrates 12 I/O pins, a 9-bit DAC, op-amp, comparators, and a 14-bit resolution-capable ADC. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, peripherals, and I/O. The PIC16HV753 belongs to the enhanced mid-range PIC® family, which sits in the broader 8-bit MCU taxonomy alongside AVR and 8051 architectures. PIC® MCUs use a Harvard architecture with separate program and data buses and a RISC instruction set optimized for deterministic, low-power embedded control. The HV prefix denotes an integrated shunt regulator that derives the internal VDD from an external high-voltage source through a series resistor - simplifying design in 9V/12V battery and constant-current LED drive applications. Key features include 3.5KB (2K x 14) self-programmable Flash, 128 bytes RAM, on-chip 9-bit DAC, internal 8MHz oscillator with PLL options, two comparators with hysteresis, an op-amp, 8/14-bit ADC, and ICSP debug support. The integrated shunt regulator eliminates an external LDO in many battery and current-source circuits, reducing BOM cost and PCB area. Architecturally, the device uses an enhanced mid-range 14-bit instruction set with 49 instructions, single-cycle execution (200ns @ 20MHz), and vectored interrupts. On-chip peripherals share dedicated I/O pins configurable through PPS-like alternate mapping, while the NanoWatt XLP power management suite provides multiple sleep modes drawing microamp-level currents. This combination supports low-duty-cycle battery designs spanning years of operation. Typical applications include LED lighting drivers, battery chargers, power management controllers, sensor signal conditioning, and 4-20mA current loops. The TSSOP-14 footprint and TSSOP package variant simplify hand-soldering for prototypes and low-volume production. When designing with this part, confirm that the PIC16HV753's integrated shunt regulator is appropriate for the supply range - the non-HV PIC16F753 variant is preferred for low-voltage (<=5.5V) designs. Use the on-chip op-amp and 9-bit DAC for closed-loop current control to minimize external component count. This page synthesizes distributor pricing, same-package alternatives, and practical design notes not collected in the manufacturer datasheet alone.

询价 联系我们
PIC16HV785-E/ML - 8-Bit 20MHz 3.5KB Flash MCU with HV Shunt Reg | Microchip
PIC16HV785-E/ML

PIC16HV785-E/ML - 8-Bit 20MHz 3.5KB Flash MCU with HV Shunt Reg | Microchip

The Microchip Technology PIC16HV785-E/ML is a 20 MHz 8-bit Flash-based CMOS microcontroller integrating a high-voltage shunt regulator, two operational amplifiers, two high-speed comparators, and a two-phase asynchronous-feedback PWM generator in a single 20-pin QFN (4x4 mm) package. According to the manufacturer datasheet, the device ships with 3.5 KB (2K x 14) of Flash program memory, 128 bytes of RAM, and 256 bytes of EEPROM, and is supported by 14-bit wide instructions and 18 general-purpose I/O pins. The integrated shunt regulator accepts input bus voltages from approximately 3.5 V to 15 V, eliminating the need for an external regulator when the MCU is powered directly from a high-voltage rail such as 12 V or a multi-cell battery stack. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path and a Harvard or von Neumann memory architecture; the PIC16 family belongs to Microchip's PIC mid-range lineup and sits at the foundation of the company's product hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. Mid-range PIC MCUs are widely used in cost- and power-sensitive embedded designs because they combine deterministic instruction execution, low quiescent current, and rich on-chip peripherals in small packages. Key features of the PIC16HV785 include two on-chip op-amps suited for current sensing in switch-mode power supplies, two high-speed comparators for cycle-by-cycle current limiting, an 8-bit ADC with 12 channels, a Capture/Compare/PWM (CCP) module plus an Enhanced CCP (ECCP), and the aforementioned dual-phase asynchronous-feedback PWM generator. The -E temperature grade spans -40 C to +125 C, supporting industrial and harsh-environment deployments. Architecturally, the device uses a RISC-style 14-bit instruction set with 35 single-word instructions and a two-stage pipeline, achieving near-1 MIPS/MHz throughput. The on-chip shunt regulator sources the core VDD from a high-voltage bus through an external resistor, allowing the MCU to operate directly from rectified mains or battery stacks. Typical applications include primary-side control of AC/DC and DC/DC switch-mode power supplies (SMPS), LED lighting drivers with analog dimming, battery chargers, smart sensors, and motor-control auxiliary circuits. The integrated op-amps are commonly configured for primary-side current sensing, while the dual comparators implement over-current protection (OCP). When designing with the PIC16HV785-E/ML, engineers should size the HV shunt resistor to limit inrush current, ensure the EP thermal pad is soldered for proper dissipation, and reserve the I2C/SPI/UART pins carefully because some peripherals share the same I/O. The QFN-20 (4x4) footprint is among the smallest in the mid-range PIC family, allowing direct drop-in reuse of layouts originally designed for PIC16F785 or PIC16HV785-I/ML variants. This page synthesizes distributor pricing, parametric alternatives, and practical design notes that go beyond what the manufacturer datasheet alone provides, including a drop-in replacement analysis for engineers facing allocation issues on this specific MPN.

询价 联系我们
PIC16HV785-E/SO - 8-Bit MCU, 3.5KB Flash, 20-SOIC | Microchip
PIC16HV785-E/SO

PIC16HV785-E/SO - 8-Bit MCU, 3.5KB Flash, 20-SOIC | Microchip

The Microchip Technology PIC16HV785-E/SO is a 20-pin flash-based 8-bit CMOS microcontroller from the PIC16 mid-range family, integrating a wide-voltage shunt regulator, dual high-speed comparators, and dual operational amplifiers on-chip, housed in a 20-SOIC (0.295 inch / 7.50 mm width) package. The "HV" suffix denotes an integrated high-voltage shunt regulator that lets the device run directly from supplies up to 15 V without an external 5 V regulator, while the "E" temperature grade marks the enhanced industrial range of -40 C to +125 C. What is a PIC16 mid-range 8-bit microcontroller? It is a RISC-architecture MCU from Microchip that executes one instruction per clock cycle (excluding branches) using a Harvard memory layout with separate program and data buses. The PIC16HV785 specifically belongs to a hybrid family that pairs the standard PIC16F785 mid-range core with an integrated high-voltage shunt regulator, eliminating the need for an external 5V LDO when powered from 12 V or 24 V rails. This product family (PIC16HV785) sits within the broader PIC16 -> PIC mid-range -> 8-bit microcontroller -> microcontroller -> embedded MCU -> semiconductor hierarchy. Key features of the PIC16HV785 include 3.5 KB of flash program memory, 256 bytes of RAM, a 20 MHz internal oscillator equivalent (8 MHz FOSC with 4x PLL, or external crystal), two on-chip op-amps, two high-speed comparators with a programmable reference, a 14-bit resolution Enhanced Capture/Compare/PWM (ECCP) module plus a standard CCP, 10-bit ADC with up to 12 channels, and an integrated high-voltage shunt regulator accepting 3.5 V to 15 V on Vdd with the HV pin sinking excess current to ground. The device supports In-Circuit Serial Programming (ICSP) via PGD/PGC pins and offers nanoWatt power management with multiple idle and sleep modes. The architecture is built on a RISC core with 35 single-word instructions and a 14-bit instruction word. Compared to the PIC16F785 (which lacks the HV regulator), the PIC16HV785 trades analog flexibility for integrated high-voltage tolerance, making it a single-chip solution for switching power supply control, LED drivers, and battery chargers. The ECCP module supports half-bridge, full-bridge, and multi-phase PWM topologies essential for offline and DC-DC converter designs. Typical applications include offline and AC-DC switched-mode power supplies (SMPS) using the on-chip comparators for primary-side regulation, LED lighting drivers with analog dimming via the op-amps, sealed lead-acid battery chargers, motor control subsystems, and any 12 V or 24 V industrial node that benefits from the integrated HV regulator. The on-chip analog peripherals minimize external component count, which is critical for cost-sensitive power electronics. A key design consideration is that the HV shunt regulator regulates by sinking excess current, so the input supply must provide adequate headroom current; bulk decoupling of at least 1 uF on Vdd and a low-ESR capacitor on the HV pin are required for stable regulation. The ECCP module's dead-band control and the comparator programmable hysteresis should be configured in firmware to match the chosen topology (buck, boost, flyback, or PFC). This page synthesizes Microchip datasheet specifications, real distributor pricing and stock as of 2026-09-22, drop-in alternatives within the PIC16HV785 family, and practical design notes for power-supply topologies not consolidated in any single source.

询价 联系我们
PIC16HV785-E/SS - 8-Bit MCU, 20MHz, 3.5KB Flash, 20-SSOP | Microchip
PIC16HV785-E/SS

PIC16HV785-E/SS - 8-Bit MCU, 20MHz, 3.5KB Flash, 20-SSOP | Microchip

The Microchip Technology PIC16HV785-E/SS is an 8-bit Flash-based CMOS microcontroller with integrated high-voltage (HV) shunt regulator support, dual operational amplifiers, and dual high-speed comparators, delivering 20MHz CPU performance in a 20-pin SSOP package. It includes 3.5KB (2K x 14) of Flash program memory, 128 bytes of RAM, and 18 digital I/O pins. The PIC16HV785 is part of the PIC16F/HV mid-range family and is optimized for closed-loop analog control applications. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and peripherals on one silicon die. MCUs belong to the broader category of microcontrollers, which fall under embedded processors, semiconductors, and integrated circuits. The 8-bit architecture executes instructions one byte (or one word) at a time, making it cost-effective and deterministic for low-power control tasks. Key features include a two-phase asynchronous feedback PWM module, two on-chip op-amps with rail-to-rail inputs, two high-speed comparators with programmable reference, internal 8MHz oscillator, and an integrated shunt regulator supporting operation directly from 3.5V to 15V supplies without an external regulator. The device supports In-Circuit Serial Programming (ICSP) and In-Circuit Debug (ICD). The PIC16HV785 uses a RISC-style Harvard design with 35 single-word instructions, providing deterministic interrupt response and low interrupt latency. The on-chip op-amps can be configured for active filtering, current sensing, or signal conditioning, while the comparators support overcurrent and zero-cross detection. Together they enable compact, single-chip SMPS, LED driver, and motor-control implementations. Typical applications include DC-DC converters, LED lighting drivers, battery chargers, solar micro-inverters, motor control, and intelligent power management. The HV regulator eliminates an external LDO, reducing BOM cost in line-powered embedded designs. When designing with this MCU, the on-chip op-amps have limited output swing and bandwidth - check the analog loop bandwidth against the switching frequency of the converter. Use the MSSP module for SPI/I2C peripheral expansion where additional memory or DACs are required. This page synthesizes distributor pricing, drop-in pin-compatible alternatives (PIC16F785, PIC16HV785-I/SS, PIC16HV785-I/SO), and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC16HV785-I/SS - 20MHz 8-bit MCU 3.5KB Flash 20-SSOP | Microchip
PIC16HV785-I/SS

PIC16HV785-I/SS - 20MHz 8-bit MCU 3.5KB Flash 20-SSOP | Microchip

The Microchip Technology PIC16HV785-I/SS is an 8-bit PIC mid-range microcontroller with 3.5KB (2K x 14) of Flash program memory, 128 bytes of RAM, and 18 digital I/O pins, housed in a 20-pin SSOP package. The "HV" prefix indicates an integrated shunt voltage regulator, enabling direct operation from a 2.0V-15V supply without external regulation. The device runs at up to 20 MHz instruction rate and includes dual operational amplifiers, dual high-speed comparators, an Enhanced Capture/Compare/PWM module, and a Two-Phase Asynchronous Feedback PWM controller on-chip. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and peripheral interfaces on a single die. Within the broader taxonomy, the PIC16HV785 sits in the 8-bit MCU class, which belongs to the microcontroller family, itself a subcategory of microcontrollers -> microprocessors -> digital ICs -> semiconductors. 8-bit MCUs dominate cost-sensitive, low-power, deterministic-control applications such as motor drive, lighting, and simple sensor conditioning because they offer predictable instruction timing, low current draw, and easy programming via the ICSP interface. Key features include one 10-bit ADC with 14 channels, one 8-bit ADC with 14 channels, two op-amps with 3 MHz gain bandwidth, two comparators with a 40 ns response time, an internal 31 kHz oscillator, and a hardware Two-Phase Asynchronous Feedback PWM block targeting switch-mode power supply (SMPS) and full-bridge converter topologies. The integrated shunt regulator accepts 2.0V-15V at the HV pin and delivers a regulated 3.3V or 5V (selectable via CONFIG) to the internal logic, simplifying power design in battery and bus-powered systems. The PIC16HV785 architecture implements the Microchip mid-range 14-bit instruction set with a single accumulator W and a 16-deep hardware stack. Peripherals share I/O pins via PPS-like multiplexers; the on-chip op-amps can be cascaded with the PWM comparators to implement current-mode control loops with no external analog components. Typical applications include primary-side control of AC-DC or DC-DC converters, LED lighting drivers, battery chargers, BLDC motor commutation, and industrial sensor signal conditioning. Because the "HV" variant integrates a shunt regulator, it is preferred over the non-HV PIC16F785 in 12V bus designs. When designing with this part, ensure the HV supply current limit resistor is sized per the datasheet's shunt regulator curve, otherwise the regulator will enter foldback. For SMPS designs, the Two-Phase Asynchronous Feedback PWM block requires external MOSFET drivers because the GPIO cannot directly drive power FETs above a few hundred milliamps. This page consolidates distributor stock, parametric drop-in equivalents, and application guidance synthesized from the Microchip PIC16HV785 datasheet, Mouser/DigiKey listings, and PIC family reference designs.

询价 联系我们
PIC16HV785T-I/ML - 8-Bit 20MHz 3.5KB Flash MCU w/ Shunt Regulator | Microchip
PIC16HV785T-I/ML

PIC16HV785T-I/ML - 8-Bit 20MHz 3.5KB Flash MCU w/ Shunt Regulator | Microchip

The Microchip Technology PIC16HV785T-I/ML is an 8-bit Flash-based CMOS microcontroller from the PIC16F family, integrating a built-in shunt voltage regulator that allows direct operation from high-voltage rails up to 15V without an external regulator. Housed in a 20-pin QFN (4x4 mm) package, it runs at 20 MHz instruction rate with 3.5 KB (2K x 14) of Flash program memory and 128 bytes of RAM, targeting mixed-signal applications such as lighting, battery charging, and power conversion. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data RAM, and peripheral set on one die; the PIC16 family uses a 14-bit wide instruction word and Harvard architecture, providing deterministic single-cycle execution for embedded control loops. The PIC16F785 specifically adds analog peripherals - two op-amps, two high-speed comparators, a 12-channel 10-bit ADC, and a two-phase asynchronous feedback PWM - that make it a system-on-chip for closed-loop analog control. The HV prefix denotes the integrated shunt regulator. Key specifications include 18 digital I/O pins, a wide operating voltage range driven by the internal shunt regulator, an internal 8 MHz oscillator with PLL options, NanoWatt power management for low standby current, on-chip EEPROM emulation, and an enhanced mid-range core with 33 instructions. The 20-QFN (4x4) package measures 4x4 mm with a thermal pad, enabling compact PCB layouts in space-constrained designs. The on-chip shunt regulator is the architectural differentiator: a typical PIC requires a regulated 2.0-5.5 V supply, but the HV785 can accept an unregulated high-voltage input (up to 15 V) and internally derive the core logic supply through a parallel-pass (shunt) topology, similar to a Zener reference. The two op-amps and comparators can be wired into closed-loop current-mode or voltage-mode control, while the two-phase PWM drives synchronous buck/boost/SEPIC stages. This integration removes external regulator and analog components, reducing BOM cost and PCB area for SMPS and LED driver designs. Typical applications include LED lighting drivers (constant-current buck/boost), battery chargers (CC/CV topologies), DC-DC converters (buck, boost, SEPIC, flyback), motor control for low-power BLDC fans, and smart power modules. The combination of analog + PWM + high-voltage input suits any closed-loop power-conversion design. When designing with the PIC16HV785, ensure the shunt regulator has a current-limiting resistor or active pass element rated for the input voltage, since the shunt sinks the difference between input current and MCU current. The op-amp outputs share package pins with comparator inputs - review the pin allocation table in the datasheet carefully. For firmware development, Microchip's MPLAB X IDE with XC8 compiler and PICkit programmers are the standard toolchain. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design considerations not found in the manufacturer datasheet alone - a complete engineering reference for selecting the PIC16HV785T-I/ML for next-generation lighting, charging, and power-conversion designs.

询价 联系我们