微控制器

产品（20,000+)

PIC16LF18345T-I/SS - 8-bit 32MHz XLP MCU 14KB Flash | Microchip
PIC16LF18345T-I/SS

PIC16LF18345T-I/SS - 8-bit 32MHz XLP MCU 14KB Flash | Microchip

The Microchip Technology PIC16LF18345T-I/SS is an 8-bit RISC microcontroller in the PIC16 family featuring eXtreme Low Power (XLP) technology, 14KB (8K x 14 words) of Flash program memory, 1KB of RAM, and 256 bytes of EEPROM, housed in a 20-pin SSOP (SS) package. It operates at up to 32 MHz internal clock from a 1.8V to 3.6V supply and integrates a rich analog and digital peripheral set including a 10-bit ADC, 5-bit DAC, two comparators, 10-bit PWM with CCP, Configurable Logic Cells (CLC), Numerically Controlled Oscillator (NCO), Complementary Waveform Generator (CWG), and Peripheral Pin Select (PPS). An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, I/O ports and peripherals around an 8-bit data path. The PIC16 family uses a Harvard RISC architecture with a 14-bit instruction word and a single accumulator (WREG) plus up-to-32-level hardware stack, balancing deterministic interrupt response with ultra-low power consumption. Within the broader taxonomy, the PIC16LF18345 belongs to the PIC16F1xxx enhanced mid-range core family, which sits above baseline PIC10/12/16 parts and below the 16-bit dsPIC33 and 32-bit PIC32 families. Key differentiating features of the PIC16LF18345 include its 32 MHz core with 125 ns instruction cycle, the Peripheral Pin Select (PPS) system that remaps digital peripherals to almost any I/O pin, four Configurable Logic Cells acting as on-chip glue logic, the Numerically Controlled Oscillator for high-resolution frequency generation without an external crystal, and a Complementary Waveform Generator for half-bridge and full-bridge drive. XLP technology delivers sub-µA sleep currents down to ~30 nA in Sleep mode with RTCC, making it one of the lowest-power 8-bit MCUs in its class. Typical applications include low-power IoT sensor nodes, battery-powered remote controls, LED lighting controllers, consumer white goods user interfaces, simple BLDC or stepper motor drive, and home automation nodes. The combination of CLC, NCO and CWG allows many of these designs to operate without external logic or timing ICs. When designing with this device, plan the ICSP/ICD pins (PGED/PGEC) into the PCB layout and provide adequate decoupling (100 nF plus 1 µF bulk) close to VDD/VSS. The 'LF' suffix indicates the 1.8V-3.6V low-voltage variant; for 2.0V-5.5V operation choose the PIC16F18345T-I/SS in the same 20-SSOP package. This page synthesizes distributor pricing, drop-in alternatives in the same 20-SSOP footprint, and practical design notes - including PPS routing and XLP sleep-current optimization - not collected in any single manufacturer document.

询价 联系我们
PIC16LF18345T-I/SSVAO - 8-Bit XLP MCU 32MHz 14KB Flash SSOP-20 | Microchip
PIC16LF18345T-I/SSVAO

PIC16LF18345T-I/SSVAO - 8-Bit XLP MCU 32MHz 14KB Flash SSOP-20 | Microchip

Microchip Technology PIC16LF18345T-I/SSVAO is an 8-bit PIC16 microcontroller built on the company's eXtreme Low Power (XLP) architecture, supplied in a 20-pin SSOP package with Tape & Reel packaging suffix. The device integrates 14KB (8K x 14 words) of Flash program memory, 1KB of SRAM and 256B of EEPROM, and executes instructions at up to 32MHz from an internal oscillator. It is qualified to AEC-Q100 standards for automotive applications and is offered in the -40C to +85C industrial temperature grade. An 8-bit PIC microcontroller (MCU) is a self-contained computing subsystem that integrates a CPU, non-volatile program memory, working RAM, data EEPROM, and a rich set of analog and digital peripherals onto a single CMOS die. PIC MCUs sit in the broader hierarchy of microcontroller -> embedded processor -> semiconductor IC, and the 'LF' prefix in this part designates the low-voltage (1.8V-3.6V) variant of the PIC16F family. The XLP designation signals that the silicon implements deep-sleep and nanoWatt technology currents that compete with the lowest-power 8-bit cores on the market. Key features of this part include a 10-bit ADC with up to 17 channels, two 8-bit timers plus a 16-bit timer, Configurable Logic Cells, Complementary Waveform Generators, multiple PWM/CCP modules, and Microchip's Peripheral Pin Select (PPS) which allows digital peripheral I/O to be remapped to most GPIO pins. The device also includes a 256B EEPROM for data logging, an Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART), MSSP I2C/SPI, and a windowed watchdog timer for safety-critical firmware. The internal 32MHz oscillator eliminates external resonator cost and the integrated Core Independent Peripherals (CIPs) let hardware logic operate without CPU intervention, enabling deterministic response times for sensor sampling, motor control, and automotive LIN slave tasks. PPS remapping of digital peripherals to different GPIO pins simplifies PCB routing and reduces BOM cost by allowing the same silicon to fit multiple board layouts. Typical applications include automotive body and lighting controllers, sensor node firmware for IoT edge devices, low-power battery monitoring, home appliance user-interface panels, and general-purpose remote-control subsystems. The AEC-Q100 qualification makes it especially attractive for under-the-hood and cabin-control modules where the temperature profile exceeds commercial limits. When designing with this part, note that the SSOP-20 (SSVAO suffix) variant is the AEC-Q100 qualified industrial-grade offering - designers should match the suffix to both the temperature range and automotive grade. Minimum operating voltage is 1.8V at 16MHz, rising to 2.5V at 32MHz, and the device retains RAM through deep sleep at currents below 1 uA. This page synthesizes AEC-Q100 automotive-grade context, drop-in alternatives, and SSOP-20 PCB layout considerations not found in the standalone manufacturer datasheet.

询价 联系我们
PIC16LF18346-E/GZ - 8-bit XLP MCU 32MHz 28KB Flash 20-UQFN | Microchip
PIC16LF18346-E/GZ

PIC16LF18346-E/GZ - 8-bit XLP MCU 32MHz 28KB Flash 20-UQFN | Microchip

The Microchip Technology PIC16LF18346-E/GZ is an 8-bit PIC microcontroller from the PIC® XLP™ 16F family, featuring a 32 MHz CPU core, 28 KB (16K x 14) of Flash program memory, 2 KB SRAM and 256 B EEPROM, housed in a 20-pin UQFN (GZ) 4x4 mm package. The 'LF' prefix denotes the wide-voltage eXtreme Low Power (XLP) variant, supporting a VDD range of 1.8V to 3.6V with operation down to 1.8V at 16 MHz for battery-driven designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program storage (Flash), and configurable peripherals around an 8-bit data path. Within the broader electronics taxonomy, 8-bit MCUs sit below 16-bit and 32-bit microcontrollers in arithmetic throughput, but their deterministic instruction timing, low power consumption, low cost and small footprint keep them dominant in cost-sensitive, deeply embedded roles such as sensor front-ends, appliance controls and battery-powered IoT nodes. The PIC16F family specifically targets applications that need Core Independent Peripherals (CIPs) - such as CLC, CWG and PPS - so that simple tasks can run without waking the CPU. Key features include Peripheral Pin Select (PPS) for flexible digital peripheral pin mapping, a 10-bit ADC with computation, two SPI/I²C, Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), and XLP technology with sub-uA sleep currents. The 20-UQFN package gives a very small PCB footprint while still exposing the full set of peripherals. The device is rated for the extended -40 °C to +125 °C operating range and ships as an 'E' (engineering sample / extended temp) grade. Typical applications include low-power IoT sensor nodes, battery chargers, energy harvesting IC front-ends, small appliances, LED lighting controllers, and remote controls. The wide operating voltage combined with deep-sleep nanoWatt XLP modes enables multi-year coin-cell battery life in duty-cycled sensor products. When designing with this MCU, ensure that decoupling is placed within a few millimetres of VDD, that unused I/O pins are configured as outputs low (not floating), and that PPS assignments do not inadvertently route peripherals onto debug pins. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet, making it a higher-value resource than a bare DigiKey or Mouser listing.

询价 联系我们
PIC16LF18346-E/P - 8-Bit XLP MCU, 28KB Flash, 32MHz | Microchip
PIC16LF18346-E/P

PIC16LF18346-E/P - 8-Bit XLP MCU, 28KB Flash, 32MHz | Microchip

The Microchip PIC16LF18346-E/P is an 8-bit PIC® XLP™ 16F microcontroller with 28KB (16K x 14 words) of Flash program memory, 2KB RAM, and 256B EEPROM, housed in a 20-pin PDIP through-hole package. It operates at up to 32 MHz from a 1.8V to 3.6V supply, integrating Core Independent Peripherals (CIPs), a 10-bit ADC with computation, configurable logic cells (CLC), complementary waveform generators (CWG), and Peripheral Pin Select (PPS) for flexible digital routing. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory (typically Flash), volatile data memory (RAM), and a configurable set of analog and digital peripherals. The PIC16LF18346 sits within Microchip's PIC16 mid-range MCU family, which occupies the entry-level to mid-tier segment of the 8-bit microcontroller market. The 'LF' prefix denotes the XLP (eXtreme Low Power) sub-family optimized for battery applications, while the 'PIC16' prefix indicates the 14-bit instruction word architecture shared across this family. Within the broader electronics taxonomy, this device belongs to: microcontroller -> 8-bit MCU -> embedded controller -> semiconductor IC. Key features include nanoWatt XLP technology with sleep currents as low as 60 nA (typical), 2x SPI/I2C, 2x UART, 2x CCP/PWM, 1x 10-bit ADC with automatic threshold scanning, 1x 5-bit DAC, 1x comparator, and up to 18 I/O pins via PPS mapping. The 20-pin PDIP package provides easy through-hole prototyping for hobbyists, educators, and low-volume production. Architecturally, the device uses a Harvard RISC core with a 14-bit instruction set and a hardware stack, executing most instructions in one cycle at 32 MHz (8 MIPS). PPS allows remapping of digital functions (CLC, CWG, CCP, PWM, communications) to nearly any I/O pin, simplifying PCB layout and reducing firmware redesign when port assignments change. Typical applications include battery-powered IoT sensor nodes, low-power wireless remotes, LED lighting controllers, environmental data loggers, consumer appliance controls, and small motor-driver front ends. The combination of PPS flexibility and CIPs enables designers to implement state machines, waveform synthesis, and sensor sampling without burdening the CPU. When designing with the PIC16LF18346-E/P, plan the power budget carefully: deep sleep draws nanoamps but active current is single-digit mA depending on peripherals enabled. Always include a 0.1µF decoupling capacitor within a few millimeters of VDD/VSS, and consider a 10µF bulk capacitor on the rail for ADC accuracy. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a faster path from selection to qualified design.

询价 联系我们
PIC16LF18346-E/SS - 8-bit XLP MCU, 32MHz, 28KB Flash | Microchip
PIC16LF18346-E/SS

PIC16LF18346-E/SS - 8-bit XLP MCU, 32MHz, 28KB Flash | Microchip

The Microchip Technology PIC16LF18346-E/SS is an 8-bit PIC microcontroller from the PIC16F/LF183xx family with eXtreme Low Power (XLP) technology, 32 MHz operation, and 28 KB (16K x 14) of Flash program memory in a 20-pin SSOP package. Operating from 1.8 V to 3.6 V with 2 KB RAM, 256 B EEPROM, a 10-bit ADC, a 5-bit DAC, two comparators, 10-bit PWM, and Core Independent Peripherals (CLC, CWG, NCO, CCP), it packs high analog integration and rich peripheral logic into a 20-pin footprint. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable I/O peripherals. An 8-bit MCU executes instructions on 8-bit wide data paths, which historically cost less per unit than 16-bit or 32-bit parts and remain economical for sensor interfacing, simple control loops, and user-interface tasks. The PIC16LF18346-E/SS sits in the Power Management > Battery-friendly tier of the PIC16 product hierarchy (PIC16 > 8-bit MCU > microcontroller > embedded computing > semiconductor). It is the "LF" (low-voltage, low-power) variant of the PIC16F18346, differing primarily in VDD range and active/quiescent current. Key features include an instruction-cycle speed of 32 MHz / 8 MIPS via the internal oscillator, 18 I/O pins with Peripheral Pin Select (PPS) for remappable digital peripherals, two EUSART modules, two SPI/I2C interfaces, on-chip debugging via ICD, and XLP nanoWatt sleep currents in the sub-microamp range. The integrated 10-bit ADC with computation (ADC2) performs automatic averaging, threshold detection, and burst-mode averaging, offloading work from the CPU. Hardware limit timers, CRC/SCAN, and zero-cross detection support functional-safety and capacitive-touch front ends. The architecture combines a RISC-style 14-bit instruction set with Harvard bus, giving deterministic single-cycle execution for most instructions and predictable interrupt latency. XLP technology uses dynamic workload scaling, deep sleep with peripheral wake-up, and a low-power WDT so battery-powered nodes can run for years from a single cell. PPS allows designers to route digital peripherals (CLC, PWM, EUSART, SPI, I2C) to any available I/O, simplifying PCB layout. Typical applications include IoT sensor nodes, low-power wireless sensor hubs, automotive body and lighting controllers, capacitive-touch user interfaces, small appliance controls, and consumer white goods. Designers choose it when they need an aggressive low-power 8-bit core with strong analog and lots of CIP logic in a small SSOP-20 footprint. When designing with this MCU, place a 100 nF decoupling capacitor adjacent to each VDD pin and use short traces to the ground paddle of the SSOP. Take advantage of PPS to clean up PCB routing, and use the ADC2 computation engine to reduce CPU wake events in battery-powered designs. Boundary-scan programming is supported but dedicated ICSP/ICD pins should remain accessible in the layout. This page synthesizes DigiKey and Mouser distributor pricing, pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a complete sourcing and design entry point.

询价 联系我们
PIC16LF18346-E/SSVAO - 8-Bit XLP MCU, 28KB Flash, 20-SSOP | Microchip
PIC16LF18346-E/SSVAO

PIC16LF18346-E/SSVAO - 8-Bit XLP MCU, 28KB Flash, 20-SSOP | Microchip

The Microchip PIC16LF18346-E/SSVAO is an 8-bit PIC® XLP™ microcontroller featuring 28KB (16K x 14) Flash program memory, 2KB RAM, and a 32MHz internal oscillator, housed in a 20-pin SSOP package. It operates from 1.8V to 3.6V, supporting low-voltage battery-powered applications, and provides 18 I/O pins with Peripheral Pin Select (PPS) for flexible digital peripheral routing. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash/RAM), and peripherals such as ADCs, timers, and communication interfaces. The PIC16LF18346 belongs to Microchip's PIC16F/LF family of 8-bit RISC microcontrollers, which sit in the broader taxonomy of microcontrollers -> embedded microcontrollers -> semiconductor ICs. The 'LF' suffix denotes the low-voltage (1.8V-3.6V) variant optimized for eXtreme Low Power (XLP) operation, while the 'F' variant supports 2.3V-5.5V. XLP technology delivers nanoWatt sleep currents in the order of tens of nA, making this part ideal for energy-harvesting and battery-backed designs. Key features include Core Independent Peripherals (CIPs) such as the Configurable Logic Cell (CLC), Complementary Waveform Generator (CWG), Numerically Controlled Oscillator (NCO), and multiple Capture/Compare/PWM (CCP) modules. The 10-bit ADC with computation, 5-bit DAC, two comparators, and EUSART/I2C/SPI interfaces provide rich analog and digital connectivity. PPS allows digital peripheral pins to be remapped at runtime, simplifying PCB layout. Architecturally, the device uses an 8-bit RISC Harvard core with a 14-bit instruction word and 32MHz maximum clock, providing up to 8 MIPS throughput. The CIPs execute hardware state machines without CPU intervention, freeing the core for low-duty-cycle sleep modes where XLP nanoWatt technology drops quiescent current to single-digit microamps. Typical applications include IoT sensor nodes, wearable health monitors, remote controls, low-power wireless sensor interfaces, automotive body electronics (the /SSVAO suffix indicates AEC-Q100 automotive qualification), and consumer battery-powered devices. The wide 1.8V-3.6V supply range is ideal for single-cell Li-ion or 2x AA battery chemistries. When designing with this part, observe the following: the PPS feature must be configured in firmware before digital peripherals can function; the /SSVAO suffix denotes automotive grade and incurs additional cost; and decoupling requires a 0.1µF ceramic capacitor placed within 3mm of VDD. Use MPLAB X IDE with XC8 compiler for development. This page synthesizes distributor pricing, automotive-grade details, same-family drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

询价 联系我们
PIC16LF18346-I/P - 32MHz 8-bit XLP MCU 28KB Flash DIP-20
PIC16LF18346-I/P

PIC16LF18346-I/P - 32MHz 8-bit XLP MCU 28KB Flash DIP-20

The Microchip Technology PIC16LF18346-I/P is a 32 MHz 8-bit PIC® XLP™ 16F microcontroller with 28 KB Flash, 2 KB SRAM, and 256 B EEPROM in a 20-pin PDIP through-hole package. It operates from 1.8 V to 3.6 V with eXtreme Low Power (XLP) features, including nanoWatt sleep and active current draw down to the microampere range for battery-friendly designs. An 8-bit microcontroller is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, and peripherals on one die. Within the broader taxonomy, the PIC16LF18346 sits in the 8-bit MCU family (microcontroller -> MCU -> 8-bit MCU -> PIC16 family -> PIC16F18xxx sub-family -> power management sub-system of an embedded design). The XLP designation specifically emphasizes ultra-low-power operation, extending battery life in portable, IoT, and energy-harvesting products compared with conventional 8-bit parts. Key features include Peripheral Pin Select (PPS) for flexible digital peripheral mapping, two Configurable Logic Cells (CLC) for hardware glue logic, a Numerical Controlled Oscillator (NCO) for fine-frequency synthesis, a 10-bit ADC with Computation, a 5-bit DAC, two CCP modules, Complementary Waveform Generation (CWG), and four 10-bit PWM channels. Two I²C and two UART/SPI interfaces support modern serial connectivity, and 256 B of EEPROM provides non-volatile data storage without external memory. The architecture uses a RISC-based 8-bit core with a 14-bit instruction word, hardware stack, and zero-latency interrupt handling. PPS routes digital peripherals to almost any I/O pin, letting designers swap pin assignments on the fly without respinning the PCB. Core Independent Peripherals (CIPs) such as CLC, CWG, NCO, and PWM operate without CPU intervention, allowing the core to remain in deep sleep and reducing average current to single-digit µA. Typical applications include battery-powered IoT sensor nodes, low-power remote controls, energy-harvesting devices, LED lighting controllers, and consumer appliances that demand long battery life and small footprints. The 20-pin PDIP package simplifies prototyping on breadboards and through-hole PCBs, making the device a common choice for evaluation, hobby, and low-volume industrial designs. When designing with this MCU, allocate decoupling capacitors (100 nF plus 1-10 µF bulk) close to VDD/AVDD pairs and respect the 3.6 V absolute maximum to avoid latch-up. Use PPS to remap peripherals before locking the I/O assignment, and verify unused peripherals are disabled in firmware to minimize quiescent draw. This page synthesizes distributor pricing, drop-in alternatives within the same PDIP-20 footprint, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC16LF18346-I/SO - 8-Bit 32MHz XLP MCU 28KB Flash | Microchip
PIC16LF18346-I/SO

PIC16LF18346-I/SO - 8-Bit 32MHz XLP MCU 28KB Flash | Microchip

The Microchip Technology PIC16LF18346-I/SO is an 8-bit PIC microcontroller from the PIC16F/LF18346 family featuring a 32 MHz CPU, 28 KB (16K x 14) of Flash program memory, 2 KB RAM, and 256 bytes of EEPROM in a 20-pin SOIC package. The device is part of the eXtreme Low Power (XLP) family and integrates a 10-bit ADC, two comparators with 5-bit DAC references, up to 10-bit PWM, CCP, CWG, CLC, and NCO peripherals, plus two independent serial communication peripherals supporting SPI and I2C. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash/ROM for program code, SRAM for data, EEPROM for non-volatile storage), and a rich set of programmable peripherals. PIC microcontrollers from Microchip Technology use a modified Harvard architecture with separate program and data buses. The PIC16F/LF18346 sits in the low-pin-count PIC16 hierarchy (PIC16 -> 8-bit PIC -> PIC microcontroller -> microcontroller -> embedded computing), and the XLP "LF" variant is engineered for battery-powered applications where nanoWatt sleep currents and active power efficiency are critical design constraints. Key features include Peripheral Pin Select (PPS), which allows digital peripheral pins to be remapped to selected device I/O for layout flexibility; a 32 MHz internal oscillator; support for an external crystal/resonator; a wide operating voltage range suitable for 2V-3.6V operation; and on-board in-circuit debugging via programming/debug pins. The 20-SOIC package (0.295 inch / 7.50 mm body width) makes the part suitable for hand-soldered prototypes as well as high-volume surface-mount assembly. Typical applications include battery-powered IoT sensor nodes, low-power wireless remote controls, LED lighting controllers, consumer appliances with touch/User-Interface buttons, industrial sensor conditioning front ends, and any battery-powered MCU application that benefits from core-independent peripherals (CLC, NCO) that can operate while the CPU sleeps. The XLP sleep modes and integrated CIP peripherals enable designs that wake briefly, process events, and return to deep sleep to extend battery life to years on a single coin cell. Designers should note that the I/SO variant is industrial temperature grade (-40C to +85C). The 20-SOIC footprint matches the standard JEDEC SO-300 mil pad pattern. When migrating to the F (Flash, 1.8-5.5V) variant, ensure the system voltage range is preserved. This page synthesizes distributor pricing, drop-in alternatives, application circuits, and practical design notes not found in the manufacturer datasheet alone, with sources traced back to the Microchip PIC16(L)F18326/18346 family datasheet and current distributor inventory.

询价 联系我们
PIC16LF18346-I/SS - 8-bit MCU 16KB Flash XLP | Microchip
PIC16LF18346-I/SS

PIC16LF18346-I/SS - 8-bit MCU 16KB Flash XLP | Microchip

The Microchip Technology PIC16LF18346-I/SS is an 8-bit PIC16 RISC microcontroller with 16 KB of Flash program memory, 2 KB of RAM, and 256 bytes of EEPROM, packaged in a 20-lead 0.34-inch-width Shrink Small Outline Package (SSOP, /SS). It runs from a 1.8 V to 3.6 V supply and reaches up to 32 MHz instruction execution, with internal oscillators trimming-resistor calibrated for low-power XLP operation. The -I suffix denotes the -40 C to +85 C industrial temperature range, making it suitable for consumer, industrial, and office-automation environments. An 8-bit microcontroller (MCU) is a compact processor that integrates CPU, RAM, non-volatile program memory, and peripherals on a single silicon die; it sits in the broader taxonomy MCU -> microcontroller -> embedded processor -> semiconductor. The PIC16F family is the workhorse mid-range line of Microchip's PIC architecture, emphasizing deterministic instruction execution, Core Independent Peripherals (CIPs), and low sleep current for battery-powered designs. Key features include a 10-bit ADC with up to 17 channels, two comparators, a 5-bit DAC, a 10-bit PWM, a Capture/Compare/PWM (CCP) module, Configurable Logic Cells (CLC), a Numerically Controlled Oscillator (NCO), and Peripheral Pin Select (PPS) for flexible digital-pin routing. Communication peripherals include two SPI/I2C interfaces and one EUSART. The XLP technology delivers sub-uA sleep currents, supressing quiescent draw in idle duty cycles. The PIC16LF18346 uses an enhanced mid-range 8-bit core with a 14-bit instruction word and hardware Multiply and hardware CLC routing, achieving close to 16 MIPS at 32 MHz. PPS allows remapping of digital peripherals to physical pins, simplifying PCB layout when module assignments change between firmware revisions. Typical applications include low-power IoT sensor nodes, battery-powered HVAC thermometers and thermostats, LED lighting controllers, consumer white goods, small appliances, and remote control transmitters. Two compact motor-control loops are also supported through the 10-bit PWM and CLC digital signal routing. When designing with this device, ensure the ICSP/ICD pins (RB7/RA0 or variant per pin map) are accessible for in-circuit programming and debugging, and pair the MCU with a low-ESR decoupling capacitor of at least 0.1 uF within 5 mm of VDD, plus a bulk 1 uF-10 uF capacitor for transient suppression. Unused I/O should be configured as outputs to minimize shoot-through current. This page synthesizes Microchip distributor pricing, same-package drop-in alternatives from the PIC16LF18346 family, and practical design notes not found in the manufacturer datasheet alone, supporting both engineers evaluating the part and sourcing teams managing second-source strategies.

询价 联系我们
PIC16LF18346T-E/GZVAO - 8-Bit XLP MCU, 28KB Flash | Microchip
PIC16LF18346T-E/GZVAO

PIC16LF18346T-E/GZVAO - 8-Bit XLP MCU, 28KB Flash | Microchip

The Microchip PIC16LF18346T-E/GZVAO is an 8-bit PIC microcontroller from the PIC16F family featuring eXtreme Low Power (XLP) technology, 28KB (16K x 14) of Flash program memory, and a maximum CPU clock of 32 MHz, housed in a 20-pin UQFN (4x4 mm) package. It is supplied on tape-and-reel with the automotive-grade /GZVAO suffix and offers -40C to +125C extended operating temperature. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates an 8-bit CPU core, program memory (Flash), data RAM, EEPROM, and a rich set of peripherals into a single IC. PIC microcontrollers are built on a modified Harvard RISC architecture: the program bus is separated from the data bus so the CPU can prefetch instructions while simultaneously reading or writing data. PIC16F-family MCUs sit in the middle of the Microchip 8-bit portfolio (PIC10/12/16/18), above PIC10/12 in capability and below PIC18 in code density, and the XLP variant is purpose-tuned for battery-powered IoT and portable products where quiescent current dominates energy budgets. Key specifications include 28KB Flash, 2KB SRAM, 256 bytes of EEPROM, a 10-bit ADC, a hardware Core Independent Peripherals (CIP) block including CLC, CWG, NCO, and CCP/PWM, plus Peripheral Pin Select (PPS) that allows digital peripherals (CLC, CWG, CCP, PWM, and communications) to be remapped to a wide choice of pins at runtime. The "LF" prefix indicates a wide 1.8V-3.6V supply range suitable for Li-ion or 2x AA battery rails. Architecturally the device pairs a Harvard RISC core with a 14-bit instruction word, a deep interrupt and DMA-style engine (the IVT and hardware CLCs), and PPS fabric that lets designers move a UART, SPI or PWM to almost any I/O pin - useful when a PCB layout forces pin reassignment late in the design. NanoWatt XLP technology drops active and sleep currents to single-digit microamp levels, enabling years of operation on a coin cell. Typical applications include IoT sensor nodes, wearable health monitors, low-power wireless sensor networks, battery-powered consumer devices, and automotive body and sensor ECUs (the /GZVAO suffix indicates the automotive/VQFN/Tape-and-Reel variant). When designing with this part, plan to use the MPLAB X IDE with the XC8 compiler and configure PPS for every digital peripheral - leaving PPS at its default assignment will limit flexibility. Always enable the watchdog timer for unattended sensor nodes. This page synthesizes distributor pricing, drop-in alternate MPNs from the same PIC16LF183xx family, and practical design notes that are not included verbatim in the manufacturer datasheet.

询价 联系我们
PIC16LF18346T-E/SSVAO - 28KB Flash 32MHz 8-bit MCU, AEC-Q100 | Microchip
PIC16LF18346T-E/SSVAO

PIC16LF18346T-E/SSVAO - 28KB Flash 32MHz 8-bit MCU, AEC-Q100 | Microchip

The Microchip Technology PIC16LF18346T-E/SSVAO is an automotive-grade, AEC-Q100 qualified 8-bit PIC microcontroller built on the company's eXtreme Low Power (XLP) 16F architecture, offering 28 KB (16K x 14 words) of Flash program memory, 2 KB of SRAM, and 256 bytes of EEPROM in a 20-pin SSOP package. The device runs at up to 32 MHz from a 1.8 V to 3.6 V supply and integrates a 5-bit DAC, 10-bit ADC, comparators, 10-bit PWM, CCP, CLC, NCO, and CWG peripherals, making it well suited for mixed-signal and motor-control subsystems in cost-sensitive automotive designs. A PIC microcontroller is a Harvard-architecture 8-bit RISC MCU that executes one instruction per clock cycle (except branches) and is widely used for embedded control in industrial, consumer, IoT, and automotive applications. Within the broader taxonomy, the PIC16 family sits between the PIC10/12/14 baseline series and the PIC18 mid-range series, balancing code density, peripheral integration, and unit cost. The 'LF' prefix denotes the low-voltage 'F' process variant optimized for sub-1.8 V operation and ultra-low sleep currents, while the '18346' part number identifies the 28 KB Flash / 2 KB RAM member of the PIC16(L)F18326/18346 sub-family. Key differentiating features include Peripheral PinSelect (PPS) for flexible digital-peripheral routing, four Configurable Logic Cells (CLC) for hardware state-machine implementation without CPU load, a Numerically Controlled Oscillator (NCO) for fine frequency synthesis, and a Complementary Waveform Generator (CWG) for high-side/low-side driver control. The XLP technology delivers nanoWatt sleep currents and active currents around 30 uA/MHz at 1 MHz, enabling battery-direct designs and Energy Harvesting products that exceed typical 8-bit MCU power benchmarks by 10x or more. Typical applications include automotive body-electronics modules (seat controllers, mirror adjusters, LED lighting, ambient lighting, and HVAC dampers), industrial sensor nodes with LIN or PWM interfaces, and ultra-low-power IoT devices with sleep duty cycling. The combination of on-chip 10-bit ADC, 5-bit DAC, comparators, and PWM eliminates the need for many external analog components. When designing with the PIC16LF18346T-E/SSVAO, ensure the decoupling network includes a 100 nF low-ESR ceramic capacitor on each VDD pin and that unused I/O are configured as outputs to minimize quiescent current. Designers should consult the device family datasheet (PIC16(L)F18326/18346) for full electrical characteristics, memory organization, and PPS mapping options. This page synthesizes distributor pricing, AEC-Q100 cross-references, and practical design notes for the SSOP-20 footprint not found in a single manufacturer datasheet.

询价 联系我们
PIC16LF18346T-I/GZ - 32MHz 8-bit MCU 28KB Flash XLP | Microchip
PIC16LF18346T-I/GZ

PIC16LF18346T-I/GZ - 32MHz 8-bit MCU 28KB Flash XLP | Microchip

The Microchip Technology PIC16LF18346T-I/GZ is an 8-bit PIC16 microcontroller featuring eXtreme Low Power (XLP) technology, 28 KB of Flash program memory, 2 KB RAM and 256 bytes of EEPROM, and runs at up to 32 MHz internal core speed. It is housed in a 20-lead UQFN 4x4 mm package, operates from 1.8 V to 3.6 V, and is rated -40C to +85C for industrial environments. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a processor, Flash program memory, data RAM, EEPROM, and a rich set of peripherals (ADC, timers, PWM, communication ports) into one device. PIC16F/LF devices from Microchip sit in the broader hierarchy: PIC16 -> 8-bit MCU -> microcontroller -> embedded controller -> semiconductor. The "LF" prefix denotes the low-voltage, low-power core variant while "F" versions extend the operating range to 5.5 V. The PIC16LF18346 specifically adds XLP technology for ultra-low sleep current, plus Core Independent Peripherals (CIPs) such as Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), and numerically controlled oscillator (NCO). Key specifications include a 10-bit ADC with up to 17 channels, two I2C/SPI interfaces, two UART interfaces, four 8-bit timers plus a 16-bit timer, Peripheral Pin Select (PPS) for flexible pin mapping, and up to 18 general-purpose I/O pins. The XLP architecture supports sleep currents below 1 uA with active run currents in the hundreds of microamps, enabling multi-year battery lifetimes on coin cells. The PIC16LF18346 family uses an enhanced mid-range 8-bit CPU with a hardware multiplier, single-cycle hardware multiply, 49 instructions, and a 16-level hardware stack. PPS allows most digital peripherals to be remapped to almost any I/O pin, simplifying PCB layout in dense designs. The 10-bit ADC is complemented by two comparators and a 5-bit DAC reference, enabling sensor and motor-control signal chains without external components. Typical applications include IoT sensor nodes, wearable health monitors, remote controls, low-power wireless sensor networks, battery-powered HVAC controls, and home automation devices. The PPS and CIP features make it well-suited to designs that need to minimize external components while maintaining long battery life. When designing with this part, select a low-quiescent LDO for the 1.8-3.6V supply to preserve the XLP sleep-current advantage, and route ADC inputs with short, guarded traces to minimize digital noise coupling. Always enable the PPS lock feature in production firmware to prevent accidental pin-function changes in noisy environments. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone, providing a faster procurement and evaluation path for engineers.

询价 联系我们
PIC16LF18346T-I/SO - 32MHz 8-bit XLP MCU 28KB Flash SOIC-20
PIC16LF18346T-I/SO

PIC16LF18346T-I/SO - 32MHz 8-bit XLP MCU 28KB Flash SOIC-20

The Microchip PIC16LF18346T-I/SO is an 8-bit PIC microcontroller from the PIC16F family featuring eXtreme Low Power (XLP) technology, 28KB of Flash program memory, 2KB RAM, and 256 bytes of EEPROM, all housed in a 20-pin SOIC package. It operates at up to 32 MHz from a 1.8V to 3.6V supply and integrates a 10-bit ADC, two SPI/I2C peripherals, and a rich set of Core Independent Peripherals (CIPs) including CLC, CWG, CCP, and PWM. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data bus, optimized for cost-sensitive embedded control where deterministic GPIO toggling and ultra-low sleep current matter more than raw compute throughput. Within the broader taxonomy, PIC MCUs belong to the microcontroller category, which sits between general-purpose microprocessors and application-specific SoCs; the PIC16F sub-family uses a 14-bit instruction word and is one of the most widely deployed 8-bit cores in industrial, consumer, and IoT products. Key features that distinguish this part include Peripheral Pin Select (PPS), which allows remapping of digital peripherals to any I/O pin for layout flexibility; eXtreme Low Power (XLP) with sleep currents below 1 uA typical; and functional safety (FuSa) support for safety-critical designs. The 256-byte EEPROM supports non-volatile user data storage without wearing the Flash array. The architecture combines a Harvard RISC core with on-chip debug, a configurable logic cell (CLC) for hardware glue logic, complementary waveform generator (CWG), and numerically controlled oscillator (NCO) blocks. PPS, CIPs, and XLP together minimize external component count and extend battery life. Typical applications include battery-powered IoT sensor nodes, consumer remote controls, low-end home appliances, industrial sensor conditioning, and portable medical peripherals. The wide 1.8V-3.6V operating range allows direct connection to single-cell Li-ion or two AA cells without additional regulation. When designing with this device, allocate one I/O for the MCLR reset function unless the internal weak pull-up is enabled via configuration bits. Use PPS early in the schematic capture to avoid layout rework when assigning peripheral functions to physical pins. This page synthesizes distributor pricing, tape-and-reel packaging details, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC16LF18346T-I/SS - 32MHz 8-bit XLP MCU, 28KB Flash | Microchip
PIC16LF18346T-I/SS

PIC16LF18346T-I/SS - 32MHz 8-bit XLP MCU, 28KB Flash | Microchip

The Microchip PIC16LF18346T-I/SS is an 8-bit PIC16 microcontroller from the PIC® XLP™ 16F family, integrating 28 KB (16K x 14) of Flash program memory, 2 KB of RAM, and 256 bytes of EEPROM into a 20-pin SSOP package rated for industrial -40°C to +85°C operation. It runs at up to 32 MHz from a 1.8 V to 3.6 V supply and is built on CMOS process technology with eXtreme Low Power (XLP) technology aimed at battery-powered designs. A 10-bit ADC with up to 12 input channels, a 5-bit DAC with 32 selectable levels, two Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART) modules and two SPI/I²C peripherals provide the analog and digital interfaces typically required by sensing, human-machine, and IoT products. An 8-bit microcontroller is a single-chip computer built around an 8-bit data path and Harvard-architecture CISC core, optimized for deterministic control of simple analog and digital I/O at very low cost and ultra-low power. Within the broader taxonomy these parts are classified as microcontrollers (MCU) -> 8-bit microcontrollers -> low-power microcontrollers -> PIC16 family -> PIC16F183xx sub-family. They sit below 16-bit MCUs and 32-bit Cortex-M cores in compute and memory scale, but excel at energy efficiency, real-time interrupt response, and short development cycles where raw MIPS-per-dollar matters more than absolute throughput. The LF18346's Core Independent Peripherals (CIPs) include the Configurable Logic Cell (CLC), Complementary Waveform Generator (CWG), Numerically Controlled Oscillator (NCO), and multiple Capture/Compare/PWM (CCP) modules that operate without CPU intervention. The Peripheral Pin Select (PPS) feature allows digital peripherals to be remapped to alternate I/O pins, which simplifies PCB layout in space-constrained SSOP designs. Instruction execution is enhanced by an internal 32 MHz oscillator that is factory calibrated to within ±1% across the full voltage and temperature range, eliminating the need for an external crystal in cost-sensitive applications. Typical applications include battery-powered sensor nodes, wearable health monitors, remote controls, low-power IoT edge devices, and capacitive-touch user interfaces. The 256-byte EEPROM is well suited for storing calibration constants, device IDs, and user preferences across power cycles, while the 2 KB RAM supports modest protocol stacks such as SMBus or Modbus slave on industrial sensors. Designers who upgrade from smaller PIC16 devices appreciate the migration path this part provides within the same MPLAB X IDE and XC8 toolchain. Designers should pair this device with a low-ESR ceramic decoupling capacitor of at least 100 nF placed within 2-3 mm of the VDD pin, and a bulk capacitor of 1-10 µF on the same rail. The unused I/O pins should be configured as outputs low or inputs with internal weak pull-ups enabled to minimize sleep current, and care must be taken to keep unused PPS-mapped peripherals in their reset state to avoid spurious wake events. This page synthesizes distributor pricing, drop-in PIC16 same-family alternatives, and practical low-power design notes that complement - not duplicate - the manufacturer datasheet.

询价 联系我们
PIC16LF18424-E/JQ - 8-bit 32MHz 7KB Flash XLP MCU | Microchip
PIC16LF18424-E/JQ

PIC16LF18424-E/JQ - 8-bit 32MHz 7KB Flash XLP MCU | Microchip

The Microchip Technology PIC16LF18424-E/JQ is an 8-bit PIC microcontroller from the PIC16(L)F184xx family, featuring eXtreme Low-Power (XLP) technology, 32MHz operation, 7KB Flash program memory, 512B RAM, and Core Independent Peripherals (CIPs) in a 16-pin UQFN (4x4) package. It integrates intelligent analog blocks including a 12-bit ADC with Computation (ADC2), a 5-bit DAC, and a comparator, alongside two PWMs, CWG, EUSART, and SPI/I2C interfaces. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and peripherals on one die. The PIC16F family from Microchip uses a RISC-based Harvard architecture with a single accumulator (WREG) and is part of the broader 8-bit MCU taxonomy that includes 8-bit -> microcontroller -> embedded processor -> semiconductor. The PIC16LF18424 belongs to the low-power (LF) sub-family, optimized for battery-powered designs through nanoWatt XLP technology, sleep currents below 1 uA, and multiple power-managed operating modes. Key features include 7KB (4K x 14) Flash program memory, 512 bytes RAM, 256 bytes EEPROM, 12-bit ADCC with automated math and averaging functions, a 5-bit DAC, two Capture/Compare/PWM modules with complementary outputs, Complementary Waveform Generator (CWG), Configurable Logic Cell (CLC), EUSART, SPI, and I2C. The 16-pin UQFN (4x4mm) package includes an exposed pad for thermal dissipation, ideal for space-constrained applications. The device operates from 1.8V to 3.6V (LF variant), supporting battery-powered designs with Li-ion or 2xAA cells. The PIC16LF18424-E/JQ uses the enhanced mid-range core with 49 instructions and 16-level hardware stack, while XLP features deliver typical sleep currents below 50 nA with RTC running. Peripherals like the CLC and CWG operate independently of the CPU, enabling low-power real-time responses. Typical applications include IoT sensor nodes, battery-powered wearables, LED lighting controllers, automotive body electronics, low-power wireless sensor hubs, consumer remote controls, and small home appliances. The combination of intelligent analog, low sleep current, and small UQFN package makes it well-suited for always-on applications that demand long battery life. When designing with this device, note the -E suffix indicates the -40C to +125C extended operating temperature range. The /JQ suffix identifies the 16-pin UQFN 4x4mm package. Programming is supported via MPLAB X IDE, XC8 compiler, and the PICkit or Snap programmer ecosystem, with configurable peripherals tunable through the MPLAB Code Configurator (MCC). This page synthesizes distributor pricing, drop-in alternatives across the PIC16(L)F184xx family, and practical design notes that complement the manufacturer datasheet.

询价 联系我们
PIC16LF18424-E/P - 8-bit 32MHz XLP MCU, 7KB Flash | Microchip
PIC16LF18424-E/P

PIC16LF18424-E/P - 8-bit 32MHz XLP MCU, 7KB Flash | Microchip

The Microchip Technology PIC16LF18424-E/P is an 8-bit PIC microcontroller built on the enhanced mid-range core, offering 7KB (4K x 14) of Flash program memory, 512 bytes of SRAM, and 256 bytes of EEPROM. It operates up to 32MHz, runs from a low-power supply range of 1.8V to 3.6V (LF variant), and integrates rich Core Independent Peripherals (CIPs) including a 12-bit ADC with Computation (ADCC), a 5-bit DAC, two PWM modules, a Complementary Waveform Generator (CWG), a comparator, EUSART, and SPI/I2C. The -E/P suffix indicates the extended (-40C to +125C) industrial temperature grade and a 14-pin PDIP through-hole package. A PIC (Peripheral Interface Controller) microcontroller is a compact, low-power programmable device that integrates a CPU, non-volatile program memory (Flash), volatile data memory (RAM), EEPROM, and a set of on-chip peripherals into a single IC. PIC MCUs sit within the broader taxonomy of microcontrollers -> embedded microprocessors -> microcomputer ICs -> semiconductors. The 8-bit PIC16 family uses a Harvard RISC architecture with a 14-bit instruction word, and the "LF" prefix denotes the low-voltage, low-power "XLP" (eXtreme Low-Power) silicon process optimized for battery-driven and energy-harvesting designs. Key features include active current consumption as low as ~32 uA/MHz at 3.3V, a nanoWatt XLP sleep current of roughly 30 nA typical, and an integrated 32MHz internal oscillator that eliminates the need for an external crystal in many designs. The 12-bit ADCC enables on-chip averaging, oversampling, and automated threshold comparisons, while the CWG and PWM peripherals simplify synchronous power-stage and lighting-control loops. Together these peripherals support digitally controlled analog loops without CPU intervention. Architecturally, the PIC16LF18424 combines the mid-range 16-bit instruction set extension with a peripheral-rich analog front-end, making it well suited to mixed-signal sensor nodes. Its internal oscillator, programmable reference and on-chip temperature indicator reduce external BOM while the 14-pin PDIP package remains breadboard-friendly for prototypes. Typical applications include battery-powered IoT sensor nodes, low-cost consumer remote controls, LED lighting control, simple motor/gate-drive timing, portable medical accessories, and industrial sensor interfaces. The wide 1.8V-3.6V supply window lets designers run directly from single-cell Li-coin or two alkaline cells. When designing with this device, place a 0.1 uF decoupling capacitor adjacent to VDD and provide a bulk cap on the MCLR pull-up network. Verify unused I/O configuration in firmware (digital vs analog) to avoid unintended current draw in XLP sleep modes. This page synthesizes distributor pricing, drop-in compatible PIC16LF18424 variants and same-family pin-compatible Microchip options, plus practical design notes not consolidated in a single manufacturer datasheet location.

询价 联系我们
PIC16LF18424-E/SL - 8-bit XLP MCU, 7KB Flash, 32MHz, SOIC-14
PIC16LF18424-E/SL

PIC16LF18424-E/SL - 8-bit XLP MCU, 7KB Flash, 32MHz, SOIC-14

The Microchip PIC16LF18424-E/SL is an 8-bit PIC microcontroller built on the eXtreme Low-Power (XLP) architecture, delivering 32 MHz of computational performance with 7 KB of Flash program memory (4K x 14 words), 512 bytes of SRAM, and 256 bytes of EEPROM. Housed in a 14-pin SOIC package, the device integrates Core Independent Peripherals (CIPs) including a 12-bit ADC with Computation (ADCC), two 10-bit PWMs, a Complementary Waveform Generator (CWG), a 5-bit DAC, two comparators, an EUSART, and SPI/I2C interfaces, enabling compact mixed-signal designs with minimal external components. An 8-bit microcontroller is a single-chip computer built around an 8-bit data path and is one of the most widely deployed categories of embedded controllers. Within the broader semiconductor taxonomy, an 8-bit MCU belongs to microcontrollers, which in turn fall under integrated circuits (ICs) used for digital control. The PIC16F family is Microchip's flagship 8-bit platform, and the LF-prefix variants (PIC16LFxxxx) are the low-voltage, low-power siblings designed for battery and energy-harvesting applications. The "F" in the part number denotes Flash program memory, and the LF prefix denotes the operating voltage family extended down to roughly 1.8V. Key features of the PIC16LF18424-E/SL include the 12-bit ADCC that offloads averaging, filtering, and threshold-comparison tasks from the CPU, the CWG for hardware-generated complementary drive signals (useful for synchronous rectifiers and triac-like outputs), and the on-chip 5-bit DAC for setpoint generation. Together these CIPs allow the CPU to remain in sleep for longer intervals, which is the foundation of the part's XLP energy budget. The device also provides multiple clock options including a 32 MHz internal oscillator, a 31 kHz low-power oscillator, and an external clock input for designers needing tight timing. The LF process technology node, combined with Microchip's eXtreme Low-Power design techniques, delivers typical sleep currents in the nanoampere range with full RAM retention, making the PIC16LF18424-E/SL competitive with MSP430 and low-end ARM Cortex-M0+ parts on energy-per-computation benchmarks. The 14-pin footprint allocates 12 general-purpose I/O pins (subject to peripheral multiplexing), which is sufficient for sensor hubs, user-interface panels, and simple IoT edge nodes. Typical applications include battery-powered IoT sensor nodes, low-power remote controls, smart-metering peripherals, white-goods user interfaces, and small appliances where the MCU must wake briefly, perform ADCC-based decision making, and return to a deep-sleep state. It is also deployed in automotive body and interior sub-modules thanks to the -E (extended) -40C to +125C temperature grade and the -Q automotive-qualified sibling (PIC16F18424-E/SLVAO). When designing with this device, reserve budget for the ICSP programming pins (PGC/PGD) and ensure MCLR is properly handled for in-circuit programming; the SOIC-14 mechanical package is straightforward to hand-prototype and rework, which is a key advantage over smaller QFN variants. The CIP-rich peripheral set means the CPU rarely needs to wake from sleep to service peripherals.

询价 联系我们
PIC16LF18424-E/ST - 8-Bit XLP MCU 32MHz 7KB FLASH 14-TSSOP | Microchip
PIC16LF18424-E/ST

PIC16LF18424-E/ST - 8-Bit XLP MCU 32MHz 7KB FLASH 14-TSSOP | Microchip

The Microchip Technology PIC16LF18424-E/ST is an 8-bit PIC16 microcontroller from the PIC16(L)F184xx family featuring eXtreme Low-Power (XLP) technology and Core Independent Peripherals (CIPs). The device runs up to 32 MHz, integrates 7 KB (4K x 14) of Flash program memory, and is housed in a 14-pin TSSOP package suitable for compact surface-mount designs. A PIC microcontroller is a microcontroller unit (MCU) based on the PIC (Peripheral Interface Controller) architecture developed by Microchip. It combines a CPU core, Flash program memory, SRAM, EEPROM, and a rich set of on-chip peripherals in a single chip. PIC MCUs belong to the broader category of embedded microcontrollers -> microcontrollers -> microprocessors -> integrated circuits -> semiconductors, and they are widely used for low-power, deterministic, mixed-signal embedded control. Key features include the high-performance 8-bit CPU with 49 instructions, hardware multiply, 7 KB Flash, 512 B SRAM, and 256 B EEPROM. Peripherals include a 12-bit ADC with Computation (ADCC), two 10-bit PWMs, a 5-bit DAC, comparators, a Complementary Waveform Generator (CWG), EUSART, SPI, and I2C. XLP technology delivers nanoWatt sleep currents, making the part suitable for battery-powered and energy-harvesting applications. The LF variant operates across a wide 1.8V to 3.6V supply range, ideal for 2x AA/AAA battery systems. It includes 12-channel 12-bit analog conversion, a configurable logic cell (CLC), and an 8-bit timer with HLT (Hardware Limit Timer), enabling flexible mixed-signal designs. Typical applications include low-power IoT sensor nodes, wearable health monitors, battery-powered remote controls, smart home edge nodes, and industrial sensor interfaces. The combination of 32 MHz operation, low sleep current, and CIP-based signal processing simplifies firmware and reduces overall BOM. When designing, leverage the eXtreme Low-Power modes and the IDLE/DOZE features to balance throughput and current. Place a 0.1 uF decoupling capacitor on VDD within 5 mm of the pin and use bulk filter near the power connector. This page synthesizes distributor pricing, drop-in alternative pinouts, and practical low-power design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC16LF18424-I/JQ - 32MHz 8-bit MCU 7KB Flash 16-UQFN | Microchip
PIC16LF18424-I/JQ

PIC16LF18424-I/JQ - 32MHz 8-bit MCU 7KB Flash 16-UQFN | Microchip

The Microchip PIC16LF18424-I/JQ is a member of the PIC16 LF184xx family of 8-bit microcontrollers built on the company's XLP (eXtreme Low Power) architecture, offering 7KB (4K x 14 words) of Flash program memory, 512 bytes of SRAM, and 256 bytes of EEPROM in a compact 16-pin UQFN (4x4 mm) package. The LF prefix indicates the 1.8V-3.6V wide operating voltage range, suiting battery-powered and energy-harvesting designs. The core runs up to 32 MHz from an internal oscillator, with a 49-day RTC from a 32 kHz source and nanowerk XLP sleep currents below 30 nA. An MCU (Microcontroller Unit) is a single-chip computer integrating a CPU, memory (Flash/SRAM/EEPROM), and programmable peripherals such as timers, ADCs, comparators, and communication interfaces. Within Microchip's taxonomy, the PIC16 LF18424 belongs to the broader category of PIC 8-bit microcontrollers -> 8-bit MCUs -> microcontrollers -> microprocessors and microcontrollers -> semiconductors. It is the LF (low-voltage, low-power) variant of the 16F18424 family, designed specifically to extend battery life in always-on sensing and IoT edge nodes. Key features include a 12-bit Analog-to-Digital Converter with Computation (ADCC) offering automated averaging, threshold detection, and hardware accumulation; a 5-bit DAC for setpoint generation; a Complementary Waveform Generator (CWG) for synchronous timing; two PWM modules; and rich digital communications with EUSART, SPI, and I2C. Peripheral Pin Select (PPS) provides flexible I/O mapping on the 16-pin package, allowing designers to remap peripherals to different pins without board rework. The architecture combines a Harvard RISC core with a 14-bit instruction word, single-cycle hardware multiply support, and a wide analog/digital integration, making it competitive with other low-end Cortex-M0 devices for cost-sensitive applications while remaining fully supported by the MPLAB X IDE, XC8 compiler, and the free MPLAB Code Configurator (MCC) peripheral setup toolchain. Typical applications include IoT sensor nodes, low-power wireless sensor transmitters, wearable health monitors, battery-powered remote controls, LED lighting controllers, and small home-appliance user interfaces. Designers choose this device when they need analog integration (12-bit ADCC, DAC, comparator), deterministic 8-bit execution, and low sleep current in a tight 4x4 mm footprint. Key design consideration: route the AVDD/AVSS pair with Kelvin returns to the VDD/VSS pins and place the 100nF decoupling within 2 mm of each supply pin. The ADCC's maximum sample rate is 100 ksps at FOSC = 32 MHz; at lower FOSC the sample rate scales linearly. This page synthesizes distributor pricing, drop-in package alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers evaluate fit, supply risk, and layout impact.

询价 联系我们
PIC16LF18424-I/P - 8-Bit XLP MCU, 7KB Flash, 14-PDIP | Microchip
PIC16LF18424-I/P

PIC16LF18424-I/P - 8-Bit XLP MCU, 7KB Flash, 14-PDIP | Microchip

The Microchip Technology PIC16LF18424-I/P is an 8-bit RISC microcontroller built on the enhanced mid-range PIC16 CPU core, delivering up to 32 MHz of operation from a 1.8V to 3.6V supply and packaged in a 14-pin PDIP through-hole format. It integrates 7 KB of Flash program memory (4K x 14 words), 512 bytes of SRAM, and 256 bytes of data EEPROM, providing a balanced memory footprint for low-power general-purpose embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, volatile data memory, and on-chip peripherals. It sits at the heart of an embedded system, executing firmware that interacts with sensors, actuators, and communication buses. The PIC16 LF family belongs to the 8-bit microcontroller category, which trades raw clock speed for predictable instruction timing, low power draw, and deterministic interrupt response. Microchip's eXtreme Low Power (XLP) technology further positions these parts for battery-powered and energy-harvesting applications. Key features include a 12-bit Analog-to-Digital Converter with Computation (ADC2), two 10-bit PWMs with complementary outputs, a 5-bit DAC, a comparator, a Complementary Waveform Generator (CWG), and configurable logic cells. Communication peripherals include EUSART, SPI, and I2C, all available on remappable pins. The device supports up to 12 I/O pins, three timers, and a wide operating temperature range of -40C to +85C for the industrial-grade variant. Architecturally, the PIC16LF18424 uses a Harvard-style modified RISC core with a hardware stack and 49 single-word instructions, achieving near-1 MIPS/MHz efficiency. The ADC2 peripheral performs automated averaging, threshold comparison, and accumulation in hardware, offloading signal-conditioning routines from the CPU. Combined with Core Independent Peripherals (CIPs), these features let the chip handle complex timing and analog tasks while the CPU sleeps. Typical applications include low-power sensor nodes, IoT edge devices, battery-powered instrumentation, LED lighting controllers, and consumer appliance interfaces. The 14-PDIP package suits breadboard prototyping, educational platforms, and through-hole production runs where rework or field replacement may be required. When designing with this device, ensure decoupling capacitors (100 nF plus 1-10 uF bulk) are placed within a few millimeters of VDD, and that unused I/O pins are configured as outputs low or inputs with internal pull-ups to minimize sleep current. Migration to the SOIC-14 (PIC16LF18424-I/SL) or TSSOP-14 footprint is straightforward when transitioning from prototype to surface-mount production. This page synthesizes distributor pricing, drop-in 14-PDIP alternatives, and practical design notes curated from the manufacturer datasheet and Microchip's CIP application notes - information that complements the datasheet without duplicating it.

询价 联系我们
PIC16LF18424-I/SL - 8-bit XLP MCU, 7KB Flash, 32MHz | Microchip
PIC16LF18424-I/SL

PIC16LF18424-I/SL - 8-bit XLP MCU, 7KB Flash, 32MHz | Microchip

The Microchip Technology PIC16LF18424-I/SL is a low-power 8-bit PIC® XLP™ microcontroller featuring 7KB (4K x 14) of Flash program memory, 512 bytes of SRAM, and a 32MHz internal oscillator, housed in a 14-pin SOIC package rated for the industrial -40C to +85C temperature range. The 'LF' prefix denotes the extended eXtreme Low-Power family, optimized for battery-powered and energy-harvesting designs where quiescent current in sleep modes can drop below 1 uA. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, integrating a CPU core, non-volatile program memory (typically Flash), working RAM, and a rich set of peripherals on one silicon die. PIC microcontrollers use a modified Harvard RISC architecture with a single accumulator (W register) and a small instruction set, which simplifies compiler design and yields highly deterministic interrupt latency. Within the broader taxonomy, the PIC16LF18424 sits under: microcontroller -> 8-bit MCU -> PIC16 family -> enhanced mid-range core -> XLP (eXtreme Low Power) subfamily -> power management and general-purpose embedded control. Key features include four 10-bit PWM channels with complementary outputs, a 12-bit Analog-to-Digital Converter with Computation (ADCC) offering automated averaging and threshold comparison, two comparators, a 5-bit DAC reference, a Complementary Waveform Generator (CWG) for synchronous motor or power control, and serial interfaces including EUSART, SPI, and I2C. The device operates from 1.8V to 3.6V, making it directly compatible with single-cell lithium coin-cell, two-AA, and 3.3V regulated rails. Core Independent Peripherals (CIPs) allow logic, timing, and signal conditioning to occur without waking the CPU, extending battery life in always-on applications. Typical applications include IoT sensor nodes, battery-powered medical wearables, low-power wireless transmitters, HVAC sensor interfaces, smart thermostats, and consumer remote controls. Designers should pair the MCU with an external 32.768 kHz crystal or use the LFINTOSC for time-keeping and select the internal HFINTOSC for active processing. Provide a 0.1 uF decoupling capacitor close to VDD and a 10 uF bulk capacitor on the board; route the MCLR pin through a 10 kohm pull-up. The device is in active production, fully RoHS compliant, and supported by MPLAB X IDE, XC8 compiler, and MPLAB Code Configurator (MCC). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC16LF18424T-I/JQ - 8-bit 32MHz 7KB Flash XLP MCU | Microchip
PIC16LF18424T-I/JQ

PIC16LF18424T-I/JQ - 8-bit 32MHz 7KB Flash XLP MCU | Microchip

The Microchip Technology PIC16LF18424T-I/JQ is an 8-bit PIC16F microcontroller IC with 32 MHz CPU speed, 7 KB (4K x 14) of Flash program memory, and integrated Core Independent Peripherals (CIPs), housed in a 16-pin UQFN (4x4) package. It belongs to the PIC16(L)F184xx XLP (eXtreme Low-Power) family, with an industrial -40°C to +85°C operating temperature range and 1.8 V to 3.6 V supply voltage for low-power operation. A PIC (Peripheral Interface Controller) microcontroller is a compact, low-cost, single-chip computer built around an 8-bit or 16-bit RISC architecture. PIC microcontrollers integrate CPU, Flash, RAM, EEPROM, and configurable peripherals (ADC, PWM, UART, comparators) on one die. PIC16 mid-range parts sit in a hierarchy: PIC microcontroller -> 8-bit MCU -> PIC16 family -> PIC16F184xx sub-family, balancing low power consumption, modest memory, and rich analog peripherals for general-purpose embedded designs. Key features include 512 B of data RAM, 12 I/O pins, a 12-bit ADCC (Analog-to-Digital Converter with Computation), two PWM channels, comparators, a CWG (Complementary Waveform Generator), EUSART, SPI, and I²C peripherals. Internal oscillator, ICD (In-Circuit Debug) support, and Microchip's nanoWatt XLP technology enable sleep currents down to nanoampere levels for battery-powered applications. Architecturally, the PIC16LF18424 uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word, hardware multiplier, and a wide peripheral set configurable through Peripheral Pin Select (PPS). Its XLP technology and CIPs (such as the 12-bit ADCC and CWG) let the device perform complex sequencing without CPU intervention, reducing active time and energy consumption in sensor and IoT nodes. Typical applications include ultra-low-power IoT sensor nodes, battery-powered wearable devices, LED lighting controllers, consumer electronics, home automation, and industrial low-power monitoring where extended battery life, integrated analog, and small form factor are required. When designing with this part, plan I/O assignments early because PPS allows flexible pin mapping. Use the MPLAB X IDE and MPLAB Code Configurator (MCC) for rapid peripheral setup, and refer to the datasheet for ADC2 acquisition time and CWG dead-band settings in motor or lighting control applications. This page synthesizes distributor pricing, cross-brand drop-in compatibility notes, and practical design guidance not aggregated in the manufacturer datasheet alone, helping engineers select and qualify the PIC16LF18424T-I/JQ efficiently.

询价 联系我们
PIC16LF18425-E/JQ - 14KB Flash XLP 8-bit MCU 16-UQFN | Microchip
PIC16LF18425-E/JQ

PIC16LF18425-E/JQ - 14KB Flash XLP 8-bit MCU 16-UQFN | Microchip

The Microchip Technology PIC16LF18425-E/JQ is an 8-bit PIC microcontroller from the PIC16(L)F184xx family, featuring a 32 MHz CPU core, 14 KB (8K x 14) of self-programmable Flash program memory, 1024 bytes of SRAM, and 256 bytes of EEPROM, all packaged in a 16-pin UQFN (4 x 4 mm) with an exposed thermal pad. It belongs to the LF (low-power) sub-family with an operating voltage range of 1.8 V to 3.6 V and integrates eXtreme Low-Power (XLP) technology with a typical sleep current below 50 nA, making it well suited to battery-operated designs. The -E suffix denotes the -40 °C to +125 °C extended industrial temperature grade and the /JQ suffix identifies the 16-UQFN package. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and a set of peripherals such as timers, ADCs, communication ports, and general-purpose I/O into a single IC. PIC16F microcontrollers sit in the broader taxonomy of embedded controllers -> microcontroller -> 8-bit MCU -> PIC architecture -> low-power XLP family. The PIC16LF18425 inherits Microchip's enhanced mid-range core with a hardware multiplier, a 49-instruction set, and a 16-level hardware stack, and is paired with rich on-chip analog and CIP peripherals. Key features include a 12-bit ADC with Computation (ADCC) supporting averaging, filtering, and threshold comparison; a 5-bit/8-bit DAC; two comparators; a Complementary Waveform Generator (CWG); two 10-bit PWMs with independent time bases; an EUSART supporting RS-232/RS-485; an SPI/I2C MSSP; a 32 kHz internal oscillator; and configurable logic cells (CLC) for hardware state-machine functions without CPU intervention. Up to 12 I/O pins are available on the 16-UQFN. The architecture separates an 8-bit data path from a 14-bit instruction word, allowing a single instruction to reference a full 14 KB Flash address space. The internal 32 MHz oscillator is factory calibrated to ±1 % over temperature and voltage, and the HFINTOSC plus LFINTOSC combine with the Fail-Safe Clock Monitor to provide robust low-power and clock-loss recovery. Typical applications include IoT sensor nodes, low-power wireless sensor endpoints (LoRa/BLE co-processors), battery-powered wearables, handheld instrumentation, automotive body and lighting modules, smart thermostats, capacitive-touch user interfaces, and low-cost motor control. Industrial uses range from PLC analog front-ends to HVAC damper controllers. Design tip: when migrating from a 5 V PIC16F design, verify that the LF variant's 3.6 V absolute maximum is never crossed at hot-plug or transient events, and place a 100 nF decoupling capacitor within 3 mm of the VDD pin with a solid ground return to the exposed pad. This page synthesizes current distributor pricing, drop-in alternatives, and practical design notes not available in the manufacturer datasheet alone, providing engineers a one-stop reference for the PIC16LF18425-E/JQ.

询价 联系我们
PIC16LF18425-E/P - 8-Bit XLP MCU, 14KB Flash, 32MHz | Microchip
PIC16LF18425-E/P

PIC16LF18425-E/P - 8-Bit XLP MCU, 14KB Flash, 32MHz | Microchip

The Microchip Technology PIC16LF18425-E/P is an 8-bit PIC16 microcontroller built on the company's eXtreme Low-Power (XLP) technology platform and packaged in a 14-pin PDIP through-hole format. It integrates 14KB of flash program memory (organized as 8K x 14 words), runs at up to 32MHz from the internal oscillator, and operates across a 1.8V-3.6V supply range that suits battery-powered and energy-harvesting designs. A microcontroller (MCU) is a single-chip computer that combines a CPU core, non-volatile program memory, volatile RAM, and a rich set of peripherals into one IC. The PIC16LF18425 sits within the broader PIC16 (8-bit RISC) family, which itself belongs to the larger category of embedded microcontrollers and, at the highest level, the semiconductor / integrated circuit product hierarchy. Microchip's PIC16F184xx generation specifically adds Core Independent Peripherals (CIPs) such as the Configurable Logic Cell (CLC), Complementary Waveform Generator (CWG), Numerically Controlled Oscillator (NCO), and a 12-bit ADC with Computation (ADCC), giving it analog and timing capability well beyond traditional PIC16 parts. Key feature highlights include up to 32MHz operation from the internal 32MHz HF oscillator, 1KB of SRAM, 256 bytes of EEPROM, a 12-bit differential ADCC, a 5-bit DAC, multiple comparators, EUSART, SPI and I2C peripherals, two PWM/CWG generators, and nanoWatt XLP sleep modes with current draw down in the sub-microamp range. The -E/P operating-temperature suffix denotes the -40C to +125C extended industrial grade. Architecturally, the PIC16LF18425 uses an 8-bit Harvard RISC core with a 14-bit instruction word, complemented by a CIP-rich analog and timing subsystem that lets peripherals operate without CPU wake-ups. The XLP nanoWatt technology uses intelligent clock gating and a deep-sleep controller to keep sleep current extremely low, enabling years of operation from a single coin cell. Typical applications include battery-powered IoT sensor nodes, low-power remote controls, smoke and CO detectors, wearable health monitors, and small appliances. Designers favor this part when they need an upgrade path from legacy PIC16F1825 designs while gaining ADCC and CWG without migrating to a Cortex-M0 core. For new layouts the -E/P suffix requires no special precautions beyond the standard 0.1-inch PDIP footprint, but firmware migration from older PIC16F1825 silicon should be reviewed against the PIC16F18425 silicon errata. This page combines distributor pricing, verified drop-in alternatives, and design notes not typically found on the manufacturer datasheet alone.

询价 联系我们