微控制器

产品（20,000+)

PIC18F06Q40-E/ST - 64KB Flash 8-bit MCU, 14-TSSOP | Microchip
PIC18F06Q40-E/ST

PIC18F06Q40-E/ST - 64KB Flash 8-bit MCU, 14-TSSOP | Microchip

The Microchip Technology PIC18F06Q40-E/ST is an 8-bit PIC18 microcontroller delivering 64 MHz CPU performance, 64 KB of Flash program memory, and 4 KB of SRAM, housed in a 14-pin TSSOP package. It integrates Core Independent Peripherals (CIPs) including a 12-bit ADC with Computation, two 8-bit DACs, and 16-bit PWM channels, making it a compact solution for real-time control and sensor interface designs. What is a PIC18 microcontroller? The PIC18 family is Microchip's high-performance 8-bit microcontroller line, succeeding the PIC16 architecture with enhanced instruction set, larger memory addressing, and richer peripherals. PIC18F06Q40 belongs to the PIC18-Q40 sub-family, which targets space-constrained IoT, medical, and industrial designs by combining the legacy PIC18 core with modern CIPs. Within the broader taxonomy, PIC18 MCUs sit alongside PIC16 (mid-range) and PIC24/dsPIC (16-bit) families as foundational building blocks for embedded control. Key features include 64 KB self-programmable Flash, 4 KB SRAM, 512 bytes EEPROM, an internal 64 MHz oscillator, and a wide 1.8V to 5.5V operating voltage. The 12-bit ADC with Computation supports up to 200 ksps conversion rate with automated post-processing (averaging, oversampling, threshold comparison) that offloads CPU work. Two 8-bit DACs, configurable PWM, CWG, SMT, and UART/SPI/I2C peripherals round out the integration. Peripherals such as the Configurable Logic Cell (CLC) and Peripheral Pin Select (PPS) provide flexible signal routing at runtime. The PIC18F06Q40-E/ST uses the enhanced mid-range PIC18 core with a 16-bit instruction word and a 31-level hardware stack, executing most instructions in one instruction cycle (4 clock cycles). Its internal voltage regulator and high-frequency oscillator (HFINTOSC up to 64 MHz) simplify BOM by eliminating external clock components. The 14-pin TSSOP package keeps the design footprint under 30 mm². Typical applications include sensor conditioning, motor control loops, IoT edge nodes, LED lighting drivers, and consumer white goods. The combination of small package, accurate ADC, and built-in DACs makes the device especially suitable for closed-loop control in industrial sensor modules. When designing, leverage MPLAB X IDE with XC8 compiler for code development. Use Microchip's MPLAB Code Configurator (MCC) to initialize CIPs graphically and minimize firmware overhead. Confirm that the E temperature grade (-40C to +125C) matches your deployment environment; the -I grade offers 0C to +85C only. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and application notes not found in the manufacturer datasheet alone, giving procurement and embedded engineers a single reference for the PIC18F06Q40-E/ST.

询价 联系我们
PIC18F06Q40-I/SL - 8-bit 64MHz 64KB Flash MCU | Microchip
PIC18F06Q40-I/SL

PIC18F06Q40-I/SL - 8-bit 64MHz 64KB Flash MCU | Microchip

The Microchip PIC18F06Q40-I/SL is an 8-bit PIC18 microcontroller built on the high-performance PIC18-Q40 family, running up to 64MHz and integrating 64KB of Flash program memory, 4KB of SRAM, and 512 bytes of EEPROM in a 14-pin SOIC package. The "I" suffix denotes the industrial temperature grade of -40C to +85C, and the "SL" package code designates the narrow-body 14-SOIC 150-mil footprint optimized for cost-sensitive designs. Core peripherals include a 12-bit ADC with Computation (ADC2), two 8-bit DACs, 16-bit PWM modules, configurable logic cells (CLC), and zero-cross detection, making it well suited for real-time control and sensor-interface applications. A microcontroller is a single-chip computer that integrates a CPU core, program and data memory, and configurable peripherals onto one die. The PIC18 family uses a modified Harvard architecture with an enhanced 8-bit RISC instruction set, 31-level stack, and hardware multiplier, occupying a middle tier in the taxonomy microcontroller -> embedded MCU -> integrated circuit -> semiconductor. The PIC18-Q40 specifically targets low-pin-count, low-cost designs in the 14-/20-pin segment. Key features include a 12-bit differential ADC2 with up to 140 ksps conversion rate, two 8-bit DACs for setpoint generation, 16-bit PWM with center-aligned and complementary output modes, and dedicated peripherals such as CLC, NCO, and DSM for signal conditioning without external logic. The device supports serial connectivity via I2C, SPI, and UART/USART plus LIN-bus master mode, and is supported by the MPLAB X IDE, MCC code generator, and XC8 compiler toolchain. Architecturally, the PIC18F06Q40 integrates Core Independent Peripherals (CIPs) that execute deterministic functions without CPU intervention, reducing firmware complexity and improving real-time response. The 64MHz internal oscillator with 4x PLL enables 16 MIPS throughput while an internal 32kHz oscillator supports low-power sleep modes. Typical applications include LED lighting controls, BLDC/PMSM ceiling-fan motor control, sensor-signal conditioning front-ends, IoT edge nodes, and small home appliances. Compact 14-pin packaging suits space-constrained PCBs where a Cortex-M0+ would be over-spec and a smaller PIC16 would lack CIP richness. When designing, reserve pins RA0/RA1 for the high-speed ADC to avoid signal-integrity loss, and follow Microchip's AN2944 layout guide for analog/digital ground separation. The internal 64MHz HFINTOSC typically eliminates the need for an external crystal, simplifying BOM and reducing cost. This page consolidates distributor pricing, drop-in alternatives, and practical design notes that are not present in the manufacturer datasheet, helping procurement and embedded engineers evaluate the PIC18F06Q40-I/SL quickly.

询价 联系我们
PIC18F06Q40-I/ST - 64KB Flash 8-bit MCU | Microchip | TSSOP-14
PIC18F06Q40-I/ST

PIC18F06Q40-I/ST - 64KB Flash 8-bit MCU | Microchip | TSSOP-14

The Microchip PIC18F06Q40-I/ST is an 8-bit PIC microcontroller from the PIC18-Q40 family, offering 64KB Flash, 4KB SRAM, and 512B EEPROM in a 14-pin TSSOP package. It operates up to 64MHz and is built around Microchip's enhanced mid-range core with a hardware multiplier, delivering up to 16 MIPS while supporting 1.8V to 5.5V operation. The device integrates a 12-bit ADC with Computation (ADC^2) for automated signal averaging, two 8-bit DACs, configurable logic cells (CLC), and Core Independent Peripherals (CIPs) such as the Complementary Waveform Generator (CWG) and Numerically Controlled Oscillator (NCO). A microcontroller (MCU) is a single-chip computer containing a CPU, memory (Flash/SRAM/EEPROM), and programmable peripherals. The PIC18 architecture belongs to the Modified Harvard 8-bit RISC family and sits within the broader category of embedded microcontrollers. The PIC18-Q40 sub-family specifically targets real-time control and sensor-interface applications by integrating analog peripherals, math accelerators, and CIPs that reduce CPU overhead and BOM cost. The 14-pin TSSOP package places this part in the small-outline surface-mount family, suitable for compact sensor nodes and space-constrained designs. Key differentiating features include the ADC^2 engine (automated oversampling, averaging, and threshold-comparison), two CLC blocks that let designers wire digital logic from on-chip peripherals without external glue, and a 32-bit CRC with memory scan for safety-critical firmware integrity checks. Communication options include I2C, SPI, UART with LIN support, and configurable IO. The on-chip 8-bit DACs and op-amp modules are useful for sensor excitation and bias generation. The device is designed for deterministic real-time control. Its interrupt structure supports hardware-priority levels, allowing time-critical peripheral events to preempt the main loop. The 16 MIPS throughput, combined with the CWG and PWM modules, suits motor, lighting, and switched-mode power control loops, while the ADC^2 reduces software complexity for sensor fusion. Typical applications include IoT sensor nodes, home-automation peripherals, battery chargers, LED lighting controllers, low-end BLDC fan drivers, small appliance control boards, and HVAC sensor interfaces. Automotive-grade variants (PIC18F06Q40-E/ST) are available for under-hood and cabin electronics requiring higher temperature tolerance. When designing with this MCU, reserve the ADC channels first, since the 14-pin TSSOP exposes a limited number of dedicated analog pins. Use the internal FVR as the ADC reference to reduce external component count, and verify interrupt priorities against your real-time deadline budget before locking the firmware architecture. This page synthesizes distributor pricing across multiple sources, pin-compatible drop-in alternatives from the same PIC18-Q40 family, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC18F06Q40T-I/SL - 8-Bit 64MHz MCU 64KB Flash 14-SOIC | Microchip
PIC18F06Q40T-I/SL

PIC18F06Q40T-I/SL - 8-Bit 64MHz MCU 64KB Flash 14-SOIC | Microchip

The Microchip Technology PIC18F06Q40T-I/SL is an 8-bit PIC18 microcontroller running at up to 64 MHz, integrating 64 KB of Flash, 4 KB of SRAM, and 512 bytes of EEPROM in a 14-pin SOIC package. It belongs to the PIC18-Q40 family, a compact high-performance product line aimed at real-time control and sensor-driven designs. Core peripherals include a 12-bit ADC with Computation (ADC2), two 8-bit DACs, and a 16-bit PWM module with complementary outputs and center-aligned capability. A microcontroller (MCU) is a single-chip computer containing a CPU, program memory, working RAM, data EEPROM, and on-chip peripherals such as ADC, DAC, timers, PWM, and communication interfaces. PIC18F MCUs use Microchip's enhanced Harvard architecture and modified RISC instruction set, positioning them within the broader taxonomy: MCU -> 8-bit MCU -> PIC18 -> PIC18F -> PIC18-Q40. The Q40 sub-family specifically targets analog-intensive closed-loop control with built-in op-amp-style analog peripherals and digital signal conditioning that reduce the need for external components. Key features include 64 KB self-programmable Flash with device information area, 4 KB SRAM supporting hardware multiplier operations, and 512 bytes of EEPROM for non-volatile user data. Communication options include UART, SPI, and I2C, while the 12-bit ADC2 with computation engine supports automated averaging, oversampling, and threshold comparisons - reducing CPU overhead in sensor applications. Two 8-bit DACs and one 16-bit PWM with multiple modes support motor, lighting, and power-supply control loops. The 14-pin SOIC package provides a small footprint suitable for compact designs while exposing five ADC channels, two DAC outputs, PWM outputs, and standard communication pins. CIP (Core Independent Peripherals) such as CWG, NCO, and the CRC scanner further offload the CPU, enabling deterministic response times even under heavy interrupt load. Typical applications include sensor signal conditioning, LED lighting control, closed-loop fan or small motor control, appliance user interfaces, and IoT edge nodes. The 16-bit PWM and dual DACs also support cost-sensitive power-conversion and battery-management tasks. When designing with the PIC18F06Q40T-I/SL, ensure the decoupling network uses a 100 nF ceramic capacitor on VDD and a bulk capacitor (typically 10 uF) near the IC. Programming and debugging are supported via ICSP (In-Circuit Serial Programming) on PGED/PGEC pins and the MPLAB ICD tools. The -I grade supports -40C to +85C operation, suitable for industrial environments. This page synthesizes distributor pricing, drop-in alternatives from the same Microchip family, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC18F06Q40T-I/ST - 8-Bit MCU, 64KB Flash, 64MHz, 14-TSSOP | Microchip
PIC18F06Q40T-I/ST

PIC18F06Q40T-I/ST - 8-Bit MCU, 64KB Flash, 64MHz, 14-TSSOP | Microchip

The Microchip Technology PIC18F06Q40T-I/ST is an 8-bit PIC18 microcontroller featuring 64KB of Flash program memory, 4KB of SRAM, and 512 bytes of EEPROM, executing instructions at up to 64MHz from a 1.8V to 5.5V supply in a 14-pin TSSOP package. The part is qualified to the -40C to +85C industrial temperature range, comes in tape-and-reel packaging, and integrates peripherals designed for real-time control and sensor-interface applications. An 8-bit microcontroller (MCU) is a compact, single-chip computer built around an 8-bit data path. It belongs to the microcontroller family, itself a subcategory of microprocessors and embedded computing. 8-bit MCUs such as the PIC18 series remain widely deployed in cost-sensitive, deterministic control applications where predictable interrupt latency, low power, and ease of use outweigh the throughput of 32-bit devices. The PIC18 line specifically extends Microchip's legacy PIC16 architecture with a larger 16-bit instruction word, linear memory model, hardware multiplier, and C-friendly compiler support, occupying a tier between simple PIC16 parts and high-end dsPIC/PIC32 devices. Key features of the PIC18F06Q40 include a 12-bit ADC with Computation (ADC2) for automated averaging, threshold detection and oversampling, two 8-bit DAC outputs, a 16-bit PWM module, DMA, Peripheral Pin Select (PPS) for flexible signal routing, and standard serial interfaces (UART, SPI, I2C). The integrated 12-bit ADC2 with up to 12 channels reduces external signal-conditioning parts, while PPS allows designers to remap digital peripherals to almost any I/O pin, easing PCB layout. The device targets real-time control and sensor-interface designs: motor and lighting control loops, IoT end nodes, white-goods HMIs, battery-powered sensor hubs, and industrial sensor-conditioning front ends. Designers migrating from smaller PIC16F or PIC18F/K parts can move to the Q40 family to gain ADC2 automation, DMA, and PPS without changing toolchains, since the part is supported by MPLAB X IDE, XC8 compilers, and the MPLAB Code Configurator (MCC). For new designs, place a 100nF decoupling capacitor close to VDD, respect the 1.8V to 5.5V supply range, and configure unused pins as outputs low to minimize current draw. The TSSOP-14 footprint allows hand-soldering-friendly prototypes but also supports standard reflow profiles for volume assembly. This page consolidates distributor pricing, package-level drop-in alternatives, and design notes that go beyond what the manufacturer datasheet alone provides, helping engineers compare, qualify, and source the part efficiently.

询价 联系我们
PIC18F06Q41-E/SL - 64KB Flash 8-bit MCU, 14-SOIC | Microchip
PIC18F06Q41-E/SL

PIC18F06Q41-E/SL - 64KB Flash 8-bit MCU, 14-SOIC | Microchip

The Microchip PIC18F06Q41-E/SL is a compact, high-performance 8-bit PIC18 microcontroller with 64KB Flash, 4KB RAM, and 512B EEPROM, running at up to 64MHz in a 14-pin SOIC package. It belongs to the PIC18-Q41 family, an analog-focused product line targeting sensor and real-time control applications, and integrates advanced peripherals including a 12-bit ADC with Computation (ADCC), two 8-bit DACs, an on-chip operational amplifier, 16-bit PWM, and configurable logic. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), non-volatile storage (EEPROM), and a rich set of peripherals (ADC, timers, communication ports, PWMs) onto one package. Within the MCU hierarchy, the PIC18F06Q41 belongs to the 8-bit microcontroller class (vs. 16-bit dsPIC or 32-bit ARM Cortex-M0/M4), which prioritizes deterministic real-time response, low cost, and ease of programming over raw throughput. The PIC18-Q41 family specifically layers analog-domain features (12-bit ADCC, on-chip op-amp, dual 8-bit DACs) on top of the classic PIC18 RISC core, making it a superset of the broader PIC microcontroller line. Key features of the PIC18F06Q41-E/SL include 64KB self-programmable Flash, 4KB SRAM, 512B EEPROM, a 64MHz internal oscillator, a 12-bit ADC with Computation supporting capacitive voltage divider (CVD), two 8-bit DACs, an on-chip op-amp, four 16-bit PWMs, multiple communication peripherals (UART, SPI, I2C), and up to 12 I/O pins in this 14-pin SOIC variant. The integrated op-amp enables small-signal conditioning without external analog components, while the ADCC automates averaging, oversampling, and threshold comparison to offload the CPU. Technically, the PIC18F06Q41 uses Microchip's enhanced mid-range 8-bit RISC core with a 16-bit instruction word, single-cycle execution for most instructions, and a hardware multiplier. The device supports wide operating voltages from 1.8V to 5.5V, multiple clock sources (internal 64MHz HFINTOSC, external crystal, and low-power LFINTOSC), and CIP (Core Independent Peripherals) that allow tasks such as signal generation, conversion, and timing to run without CPU intervention - critical for low-power sensor nodes. Typical applications include capacitive touch sensing, sensor signal conditioning, LED lighting control, battery-powered IoT end nodes, small motor and fan control, and medical or industrial sensor front-ends. The high level of analog integration is particularly valuable in space-constrained designs where external op-amps and ADCs would push BOM cost and PCB area beyond budget. When designing with this device, plan pin allocation carefully because the 14-SOIC variant exposes only 12 I/O pins; for designs requiring more I/O, consider the 20-pin SOIC/SSOP variant (PIC18F16Q41). Also budget for proper decoupling (100nF plus 1uF) close to VDD/VSS, and verify the ADC reference voltage against your sensor output range to avoid gain errors. This page synthesizes distributor pricing, parametric alternatives, and design considerations for the PIC18F06Q41-E/SL that are not collected in any single manufacturer document, helping procurement teams and design engineers evaluate the part with maximum context.

询价 联系我们
PIC18F06Q41-I/ST - 64KB Flash 8-bit MCU 14-TSSOP | Microchip
PIC18F06Q41-I/ST

PIC18F06Q41-I/ST - 64KB Flash 8-bit MCU 14-TSSOP | Microchip

The Microchip Technology PIC18F06Q41-I/ST is a compact 8-bit PIC18 microcontroller from the PIC18-Q41 family, delivering 64KB Flash, 4KB SRAM and 512B EEPROM in a 14-pin TSSOP package. It integrates a 12-bit ADC with Computation (ADCC), two 8-bit DAC modules, an on-chip operational amplifier, and 16-bit PWM peripherals tuned for sensor and real-time control loops. An 8-bit microcontroller (MCU) is a microprocessor whose data path, registers, and ALU operate on 8 bits at a time; it sits inside the broader taxonomy of microcontrollers -> embedded processors -> semiconductors -> integrated circuits. 8-bit MCUs are favored for cost-sensitive, deterministic, low-power applications because the CISC-style PIC18 instruction set keeps interrupt latency short and code density high, while the Q41 family layers modern analog and CIP (Core Independent Peripheral) blocks onto the legacy architecture. Key features include 64MHz operation (16 MIPS), 12-bit ADCC with up to 22 channels (shared with package pins), two 8-bit DACs, an on-chip op-amp, configurable logic cells, multiple 16-bit PWMs with complementary outputs, and CIP peripherals that automate capacitive voltage divider (CVD) touch sensing without CPU intervention. Memory-protection, hardware limit timers, and math accelerators further reduce firmware load. The Q41 silicon uses a CIP-rich architecture that lets peripherals (ADC, PWM, op-amp, CLC) cooperate without waking the CPU, enabling deterministic sub-microsecond control loops in motor, lighting, and sensor-conditioning designs. The 12-bit ADCC oversampling/threshold block performs averaging and decision logic in hardware, allowing unattended sensor polling at very low average current. Typical applications include capacitive touch user interfaces, LED lighting drivers, sensor signal conditioning, low-cost motor control (BLDC/PMSM FOC with external gate drivers), battery-powered IoT edge nodes, and small home appliances. The integrated op-amp plus dual DAC lets a single MCU implement analog front-end plus actuator drive. When designing with this part, note that the 14-pin TSSOP exposes a limited I/O count (about 12 usable GPIO once programming and crystal pins are reserved), so plan pin assignments before schematic capture. Always use the latest PIC18-Q41 family programming spec and errata before locking production firmware. This page synthesizes verified distributor pricing, drop-in TSSOP-14 alternatives from the same PIC18-Q41 family, and practical design notes not found in the standalone datasheet PDF.

询价 联系我们
PIC18F06Q41T-I/SL - 8-bit 64MHz MCU 64KB Flash 14-SOIC | Microchip
PIC18F06Q41T-I/SL

PIC18F06Q41T-I/SL - 8-bit 64MHz MCU 64KB Flash 14-SOIC | Microchip

The Microchip Technology PIC18F06Q41T-I/SL is an 8-bit PIC18 microcontroller running up to 64 MHz with 64 KB Flash, 4 KB SRAM and 512 bytes EEPROM, housed in a 14-pin SOIC package. It belongs to the PIC18-Q41 family, which combines a high-performance PIC18 core with Core Independent Peripherals (CIPs) and advanced analog blocks for sensor and real-time control designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile working memory (RAM), and a configurable set of peripherals such as timers, ADC, DAC, communication interfaces and CIPs. PIC18F devices sit at the top of Microchip's 8-bit portfolio with an enhanced instruction set, 16-bit-wide instruction path and vectored interrupt architecture, while the Q41 sub-family layers analog-rich peripherals on top of this core. Key features of the PIC18F06Q41T-I/SL include a 12-bit ADC with Computation (ADCC), two 8-bit DACs, a 16-bit PWM module, an on-chip operational amplifier, zero-cross detection, a hardware limit timer and Configurable Logic Cell (CLC) blocks. CIPs allow AD conversion, threshold comparison and signal generation without CPU intervention, easing deterministic firmware in motor, lighting and sensor-interface products. The part operates from 1.8 V to 5.5 V VDD, supports up to 64 MHz internal or external clocking, and offers multiple low-power modes (Doze, Idle and Sleep with <100 nA typical). Integrated DMA and vectored interrupts keep latency predictable when the analog front-end and PWM are active simultaneously, which is critical for tight-loop control. Typical applications include LED lighting drivers, BLDC/PMSM motor control, sensor signal conditioning, industrial control loops, medical wearables, IoT end-nodes, and battery-powered instrumentation. The 14-SOIC footprint makes it attractive where PCB area is constrained but analog performance is non-negotiable. When designing with this device, mind the 14-pin pinout: only one dedicated I/O port is available, so prioritizing which peripherals map to which pins is essential during schematic capture. Always refer to the Microchip PIC18F06/16Q41 datasheet for pin muxing, IDDx limits and programming/debug interface requirements. This page synthesizes distributor pricing, drop-in alternatives and engineering notes that go beyond the manufacturer datasheet, helping procurement and design engineers converge on the right 8-bit MCU faster.

询价 联系我们
PIC18F06Q41T-I/ST - 8-bit 64MHz MCU 64KB Flash | Microchip
PIC18F06Q41T-I/ST

PIC18F06Q41T-I/ST - 8-bit 64MHz MCU 64KB Flash | Microchip

The Microchip Technology PIC18F06Q41T-I/ST is an 8-bit PIC18 microcontroller operating at up to 64MHz, integrating 64KB of Flash program memory, 4KB SRAM, and 512 bytes of EEPROM in a 14-pin TSSOP package. The device belongs to the analog-rich PIC18-Q41 family designed for sensor and real-time control applications, featuring a 12-bit ADC with Computation (ADCC) that automates Capacitive Voltage Divider (CVD) techniques, two 8-bit DAC modules, an on-chip operational amplifier, a 16-bit PWM, DMA, and configurable Peripheral Pin Select (PPS). An 8-bit microcontroller (MCU) is a microprocessor integrated with program memory, RAM, peripherals, and I/O on a single silicon die, using an 8-bit data path. Within the broader taxonomy, this PIC18 sits under microcontroller -> embedded controller -> digital IC -> semiconductor. The 8-bit class excels in deterministic real-time control, low power consumption, and low cost per unit, making it the preferred choice for appliance controls, sensor hubs, and human-interface designs where 32-bit performance is unnecessary. Key features include 64KB self-programmable Flash with 256-byte block erase, 4KB linear SRAM, 512 bytes EEPROM emulation, a 12-bit ADCC with up to 12 channels, two 8-bit DACs with rail-to-rail output, an integrated 5MHz op-amp, six 16-bit timers, DMA controller for peripheral-to-memory transfers, and three DMA channels. Communication peripherals include UART, SPI, and I2C, all routed via PPS to most I/O pins. The PIC18-Q41 architecture uses a modified Harvard structure with a 16-bit instruction word and an 8-bit data path, executed through a 2-stage pipeline. The on-chip op-amp enables single-supply signal conditioning without external analog ICs, while the ADCC supports hardware-averaged oversampling and threshold comparisons that offload CPU cycles. PPS allows remapping of digital peripherals to nearly any I/O, simplifying PCB layout. Typical applications include capacitive touch sensing using CVD, low-power sensor nodes, LED lighting controls with 16-bit PWM dimming, and small appliance controls such as coffee makers and fans. With the integrated op-amp, the device can directly interface with analog sensors, including thermistors and photodiodes, eliminating external signal-conditioning stages. When designing with this MCU, ensure VDDCORE decoupling (100nF plus 1uF) is placed within 2mm of the pin, route MCLR with a 10k pull-up, and use PPS to optimize PCB routing. For low-power operation, take advantage of the Sleep mode with peripheral wake-on-touch. This page synthesizes verified distributor pricing, drop-in alternative cross-references, and practical design notes that complement the manufacturer datasheet.

询价 联系我们
PIC18F1220-E/P - 8-bit MCU 4KB Flash 16 I/O 18-DIP | Microchip
PIC18F1220-E/P

PIC18F1220-E/P - 8-bit MCU 4KB Flash 16 I/O 18-DIP | Microchip

The Microchip Technology PIC18F1220-E/P is a high-performance 8-bit CMOS flash-based microcontroller with 4KB of program memory, 256 bytes of SRAM, and 128 bytes of EEPROM, housed in a 18-pin PDIP (DIP-18) through-hole package. It executes instructions at 200 ns (10 MIPS at 40 MHz) using the PIC18 RISC architecture and operates from 2.0V to 5.5V across the -40C to +125C industrial temperature range. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data bus and CISC/RISC core, integrating CPU, RAM, non-volatile program memory, peripherals and I/O on one die. The PIC18F1220 belongs to the PIC18 family -> PIC microcontrollers -> 8-bit microcontrollers -> microcontrollers -> integrated circuits (semiconductors). It targets applications needing deterministic real-time control with on-chip analog and serial peripherals. Key differentiating features of this device include 7 channels of 10-bit Analog-to-Digital conversion, an Addressable Universal Asynchronous Receiver Transmitter (AUSART) module, a Capture/Compare/PWM (CCP) peripheral, self-programming flash, ICD (In-Circuit Debug), and Microchip's nanoWatt advanced low-power modes with multiple oscillator options including a 31 kHz low-power secondary oscillator. These integrated peripherals eliminate most external components in typical embedded designs. Architecturally, the PIC18F1220 uses a 16-bit instruction word with an 8-bit data path and 21 interrupt sources, supporting linear program memory up to 2 MB via table reads. Its wide operating voltage (2.0V-5.5V) and 16 I/O pins with individual direction control make it suitable for both 3.3V and 5V designs, while the nanoWatt technology provides <1 uA sleep current for battery-powered applications. Typical applications include industrial control logic, sensor signal conditioning, low-power remote sensor nodes, automotive body and climate subsystems, and small appliance control panels. Its 16 I/O and 7 ADC channels cover most 8-bit embedded designs without external muxing. When designing with this part, route VDD/VSS pairs with low-ESR decoupling (100 nF plus 10 uF bulk) and keep analog signals short to AVss/Vdd. For low-power operation, use the nanoWatt sleep modes plus the 31 kHz secondary oscillator; do not exceed 40 MHz on Fosc to avoid oscillator-amplifier failure modes. This page synthesizes current distributor pricing, pin-compatible drop-in alternatives from the PIC18F family and cross-brand 8-bit MCU landscape, and practical design notes not aggregated in the manufacturer datasheet.

询价 联系我们
PIC18F1220-E/SS - 8-bit MCU, 4KB Flash, 25MHz, SSOP-20 | Microchip
PIC18F1220-E/SS

PIC18F1220-E/SS - 8-bit MCU, 4KB Flash, 25MHz, SSOP-20 | Microchip

The Microchip Technology PIC18F1220-E/SS is an 8-bit high-performance RISC microcontroller with 4KB (2K x 16) of Enhanced Flash program memory, 256 bytes of RAM, and 128 bytes of EEPROM, housed in a 20-pin SSOP package. It executes instructions in 200 ns at a 25 MHz clock and integrates 10-bit Analog-to-Digital conversion, AUSART, capture/compare/PWM, and nanoWatt low-power modes. An 8-bit microcontroller (MCU) is a small computer on a single integrated circuit that contains a CPU, RAM, non-volatile program memory, and peripherals. MCUs sit within the broader category of microcontrollers -> embedded processors -> semiconductors. The PIC18F1220-E/SS belongs to the PIC18 family, which combines a RISC core with Enhanced Flash memory to deliver 200 ns instruction execution while maintaining C-compiler-friendly architecture for efficient code development. It belongs to the wider product taxonomy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. Key features include seven channels of 10-bit A/D, self-programmability via ICSP, an internal oscillator option that can reduce BOM cost, and a 2.0V to 5.5V operating voltage range suited to battery-powered applications. Power consumption drops to as low as 0.1 microamp in standby. The device supports flash endurance of 100K cycles and EEPROM endurance of 1M cycles typical, giving long field-life in industrial control nodes. Architecturally, the PIC18F1220-E/SS uses a 16-bit wide instruction word with an 8-bit data path, a 31-level hardware stack, and an interrupt controller supporting both edge- and level-triggered sources. The AUSART block supports RS-232/RS-485 asynchronous links, while the CCP module generates PWM for motor or LED control, all inside a compact 20-pin SSOP outline. Typical applications include low-power sensor nodes, battery management front-ends, small motor control, white-goods user interfaces, and remote-control peripherals where the wide 2.0-5.5V supply range and nanoWatt sleep modes extend operating life from coin cells or two-AA stacks. Designers also use it as a cost-down companion to larger PIC18F parts in cost-sensitive consumer goods. When designing, choose the 'E' (Extended) temperature grade -40C to +125C variant for outdoor or industrial enclosures. Provide a 100 nF decoupling capacitor close to VDD, route the MCLR line away from switching traces to avoid spurious resets, and verify ICSP pins (RB6/RB7) are not loaded by external pull-ups that would block in-circuit programming. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC18F1220-H/ML - 4KB Flash 8-bit MCU, 28-QFN | Microchip
PIC18F1220-H/ML

PIC18F1220-H/ML - 4KB Flash 8-bit MCU, 28-QFN | Microchip

The Microchip Technology PIC18F1220-H/ML is an 8-bit RISC PIC18 microcontroller with 4 KB of Flash program memory, 256 bytes of SRAM and 128 bytes of EEPROM, housed in a 28-pin QFN package with exposed thermal pad. It operates across 2.0V to 5.5V with nanoWatt power management, integrates 7 channels of 10-bit ADC, AUSART, MSSP, two capture/compare/PWM modules, and supports up to 16 digital I/O pins. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), non-volatile data storage (EEPROM), and a rich set of peripherals. The PIC18F1220 sits in the PIC18 family of high-performance 8-bit RISC microcontrollers, above the baseline PIC10/12/16 families in instruction width and peripheral capability, and below PIC24/dsPIC in 16-bit performance. Within Microchip's taxonomy, this part is a member of the power-managed, self-programming, ADC-rich nanoWatt class targeted at cost-sensitive embedded applications. Key features include a 25 MIPS execution speed at 40 MHz oscillator, hardware multiplier, 16-bit instructions with 8-bit data path, self-programming Flash, in-circuit debugging (ICD), and nanoWatt sleep/idle modes for battery-powered designs. The integrated 10-bit ADC provides 7 analog input channels at up to 30 ksps conversion rate, sufficient for sensor monitoring and process control. The PIC18F1220 architecture combines Harvard bus structure with C-compiler-optimized instruction set. Code is executed from Flash with single-cycle access for most instructions, and 4 KB of program space supports mid-complexity embedded firmware. Hardware CCP and ECCP modules simplify motor, lighting, and power-converter control loops. Typical applications include low-power sensor nodes, white-goods and appliance control, lighting ballast controllers, low-end motor control, automotive body electronics, and battery-powered instrumentation where nanoWatt sleep currents extend operating life. When designing with the PIC18F1220-H/ML, observe QFN thermal pad soldering guidelines and route MCLR, VDD, VSS and decoupling capacitance to the exposed pad to ensure reliable operation in noisy industrial environments. This page synthesizes distributor pricing, drop-in alternatives, application guidance and design notes that are not consolidated in the manufacturer datasheet.

询价 联系我们
PIC18F1220-H/SO - 8-bit 25MHz 4KB Flash MCU | Microchip
PIC18F1220-H/SO

PIC18F1220-H/SO - 8-bit 25MHz 4KB Flash MCU | Microchip

The Microchip PIC18F1220-H/SO is an 8-bit PIC18 RISC microcontroller running at up to 25 MHz, integrating 4 KB of Flash program memory (2K x 16 words), 256 bytes of SRAM, and 128 bytes of EEPROM in a high-temperature grade (-40C to +150C) variant housed in an 18-pin SOIC package. The H temperature suffix designates the high-temperature AEC-Q100-style extended range commonly used in automotive under-hood and industrial environments, distinguishing it from the industrial I grade (-40C to +85C). A microcontroller is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and a rich set of peripherals (timers, ADC, communication ports, GPIO) into one package. Within the PIC18 family from Microchip Technology, the PIC18F1220 sits at the low-pin-count end of the high-performance enhanced-Flash line, sitting below the PIC18F1320 and above the base PIC16F series. It is engineered for cost-sensitive, deterministic embedded control where an 8-bit architecture, small footprint, and low power consumption matter more than raw MIPS. Key features include an enhanced 16-bit instruction set with 75 instructions and an 8 x 8 hardware multiplier, self-programmability for in-field firmware upgrades, an ICD (In-Circuit Debug) interface, capture/compare/PWM modules, 7 channels of 10-bit Analog-to-Digital conversion, an Addressable USART (AUSART), and advanced low-power modes controlled by Microchip's nanoWatt Technology. The 18-SOIC (0.295 inch / 7.50 mm body) gives designers a widely available, easy-to-protoboard package. Architecture-wise, the PIC18F1220 uses a 14-bit-wide Flash path and a 16-bit instruction word that yields an 8 MIPS throughput at 25 MHz (4-clock-per-instruction pipeline). Peripherals share the same interrupt vector with priority levels and a software-selectable oscillator source (internal RC, external crystal, HS, or EC modes), simplifying BOM cost when an external crystal can be eliminated entirely. Typical applications include automotive body and chassis modules, HVAC and climate controls, small appliance motor control (CCP/PWM-driven), sensor signal conditioning with the 10-bit ADC, low-cost user-interface controllers, and battery-powered industrial sensors. The high-temp H grade opens under-hood, white-goods, and outdoor equipment markets that the I-grade PIC18F1220-I/SO cannot address. When designing with this part, choose decoupling capacitors per the datasheet (typically 100 nF on VDD plus a bulk 10 uF) and pay attention to the ICSP/ICD pin sharing to avoid contention with the application circuit. The Flash endurance is rated at 100K cycles minimum, so EEPROM emulation should be reserved for rarely-changed parameters. This page synthesizes distributor pricing, drop-in alternatives drawn from the same Microchip PIC18 family, and practical design notes that complement rather than copy the manufacturer datasheet, helping procurement and engineering teams quickly decide whether the PIC18F1220-H/SO is the right MCU for their BOM.

询价 联系我们
PIC18F1220-H/SS - 8-bit 25MHz 4KB Flash MCU | Microchip
PIC18F1220-H/SS

PIC18F1220-H/SS - 8-bit 25MHz 4KB Flash MCU | Microchip

The Microchip Technology PIC18F1220-H/SS is an 8-bit RISC PIC18 microcontroller with a 25 MHz core, 4 KB (2K x 16) of Flash program memory, 256 bytes of SRAM and 128 bytes of EEPROM, housed in a 20-pin SSOP package rated for the automotive (-H) temperature grade of -40C to +150C. It targets cost-sensitive embedded control nodes that need a self-programmable Flash, an ICD debug port and a small analog footprint in one of the smallest PIC18 packages. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile data memory (SRAM), a small amount of byte-erasable EEPROM, and a set of on-chip peripherals (timers, ADC, communications ports, I/O). The PIC18F family extends the PIC16 baseline with a 16-bit instruction word, linear addressing and a richer interrupt controller, placing the PIC18F1220 in the broader hierarchy: MCU -> 8-bit MCU -> PIC18 family -> enhanced Flash microcontrollers. This positioning explains why the PIC18F1220 still ships today: it covers applications that need 8-bit simplicity but require more code space and EEPROM than a baseline PIC16 can provide. Key features include 16 general-purpose I/O pins, 7 channels of 10-bit Analog-to-Digital converter (ADC), an Addressable USART (AUSART) for RS-232/RS-485, capture/compare/PWM modules and nanoWatt Technology with six software-controlled power-managed modes that drop standby current to approximately 0.1 uA. The 'C' compiler-friendly architecture (16-bit instructions, linear data memory) allows the device to be programmed in standard C with the MPLAB XC8 toolchain, reducing time-to-prototype versus assembly-only PIC16 designs. Typical applications include automotive body and chassis nodes (the -H temperature grade qualifies this part), low-power remote sensor transmitters, household appliance control boards, lighting controllers, and industrial interface modules that previously used PIC16F parts but have outgrown their Flash budget. Two independent analog comparators plus a 10-bit ADC make the device a common choice for battery management front-ends and fan/PWM closed-loop control. When designing with this MCU, choose between the internal 8 MHz oscillator and an external crystal; the PLL block is not present, so system clock is capped at 25 MHz from the PLL-less 4x branch. Brown-out reset and watchdog timer are configured in configuration words - do not leave them at factory defaults. For applications that demand more memory or more pins, migrate to PIC18F1320 or PIC18F24K20 rather than attempting to externally bank the 4 KB Flash.

询价 联系我们
PIC18F1220-I/ML - 8-bit MCU, 4KB Flash, 40MHz | Microchip
PIC18F1220-I/ML

PIC18F1220-I/ML - 8-bit MCU, 4KB Flash, 40MHz | Microchip

The Microchip Technology PIC18F1220-I/ML is an 8-bit PIC18 enhanced flash microcontroller running at up to 40 MHz, integrating 4 KB of flash program memory (2K x 16), 256 bytes of SRAM, and 128 bytes of EEPROM in a 28-pin QFN (6x6 mm) package (package designator ML). It operates across a wide 2.0 V to 5.5 V supply range, supports 16 general-purpose I/O pins, and offers seven channels of 10-bit analog-to-digital conversion, an Addressable USART (AUSART), capture/compare/PWM peripherals, and an in-circuit debugger interface. An 8-bit microcontroller (MCU) is a small, self-contained computing core that integrates CPU, RAM, non-volatile program memory, timers, and I/O peripherals onto a single silicon die. PIC18F-series parts are mid-range 8-bit MCUs in the broader microcontroller taxonomy (8-bit MCU -> microcontroller -> embedded controller -> semiconductor). They are favored where deterministic execution, low power, and a Harvard RISC architecture matter more than raw compute throughput. Key features of the PIC18F1220 include nanoWatt Technology with six software-controlled power-managed modes, standby current as low as 0.1 microamp, self-programmability, an ICD (in-circuit debugger) interface, and 10-bit ADC. The ML package is the lead-free 28-pin QFN variant with an exposed thermal pad, suitable for compact surface-mount designs where the SOIC, SSOP, or DIP variants would consume too much PCB area. The PIC18F1220 employs an enhanced Harvard RISC architecture with a 16-bit instruction word and 8-bit data path, an 8 x 8 hardware multiplier, and a vectored interrupt controller. The flash memory supports self-programming via ICSP, allowing in-application firmware updates without an external programmer, and the nanoWatt modes include Run, Idle, Sleep, and several timer-driven wake variants for battery-optimized duty cycles. Typical applications include battery-powered sensor nodes, low-cost motor control (small DC brushed or stepper drivers via PWM + ADC), small appliances and white goods, capacitive-touch front panels using the AUSART for communication, USB-to-UART bridges when paired with an external PHY, and lighting ballast control. The wide 2.0-5.5 V range means a single part can run from a 3.3 V LDO or directly from a 2-cell AA pack. When designing with this part, verify the ICSP/ICD pin assignments (PGC/PGD/MCLR) match your programming header and that the AUSART pins are not remapped onto I/O lines used by the ADC channels you need. The QFN exposed pad must be soldered to a sufficiently large copper pour for thermal and electrical performance.

询价 联系我们
PIC18F1220-I/P - 8-bit 40MHz 4KB Flash MCU | Microchip DIP-18
PIC18F1220-I/P

PIC18F1220-I/P - 8-bit 40MHz 4KB Flash MCU | Microchip DIP-18

The Microchip Technology PIC18F1220-I/P is an 8-bit PIC18 microcontroller running at up to 40 MHz, integrating 4 KB of Flash program memory (2K × 16), 256 bytes of RAM and 128 bytes of EEPROM in an 18-pin PDIP (DIP-18, 0.300 inch / 7.62 mm) through-hole package. The device features the high-performance RISC PIC18 core, an internal oscillator, a 10-bit ADC with up to 7 channels, an AUSART, capture/compare/PWM peripherals, self-programming Flash and In-Circuit Debug (ICD). NanoWatt Technology power management adds multiple low-power modes for battery-driven designs. A PIC microcontroller is a compact programmable computing device built around a Harvard-architecture RISC core with on-chip Flash, RAM and peripherals; it sits in the broader hierarchy of microcontroller -> embedded computing subsystem -> semiconductor IC. The PIC18 family specifically targets higher-performance 8-bit applications where code density, deterministic timing and rich peripherals matter more than raw CPU frequency. Differentiating features include seven 10-bit ADC channels for mixed-signal sensing, AUSART for asynchronous serial communications, configurable CCP modules for PWM and timing, an internal oscillator that often eliminates the external crystal, and 16 general-purpose I/O pins. Self-programming allows field firmware upgrades, while the ICD interface supports real-time debug without removing the part from the board. The architecture uses a 16-bit instruction word with an 8-bit data path, an 8 × 8 hardware multiplier and a hardware stack that simplifies interrupt handling. The 40 MHz internal clock (10 MHz instruction rate with the 4-F cycle) delivers approximately 10 MIPS of throughput, while nanoWatt modes cut quiescent current below microamp levels for sleep-heavy applications. Typical uses include small motor control, sensor front-ends, automotive body electronics, hobby robotics, white-goods user interfaces, low-cost consumer appliances and industrial sensor nodes where the DIP-18 footprint simplifies prototyping. The wide operating temperature range suits outdoor and industrial deployments. When designing with the PIC18F1220-I/P, plan decoupling with a 100 nF ceramic plus bulk capacitor near VDD, reserve an unused port bit for ICD or programming, and respect the 5.5 V absolute-maximum VDD to avoid latch-up during hot-plug events. This page combines distributor pricing, drop-in same-package alternatives and practical engineering notes that go beyond the manufacturer datasheet alone to accelerate part selection and BOM risk reduction.

询价 联系我们
PIC18F1220-I/SS - 8-bit MCU, 4KB Flash, 40MHz, SSOP-20 | Microchip
PIC18F1220-I/SS

PIC18F1220-I/SS - 8-bit MCU, 4KB Flash, 40MHz, SSOP-20 | Microchip

The Microchip Technology PIC18F1220-I/SS is an 8-bit high-performance enhanced flash microcontroller delivering 40 MHz (10 MIPS) CPU performance from 4KB of program memory and 256 bytes of SRAM in a 20-pin SSOP package. It features a wide 2.0V to 5.5V supply range, nanoWatt Technology power management, and 16 digital I/O pins suitable for compact embedded designs. What is an 8-bit microcontroller? An MCU (microcontroller unit) is a single-chip computer integrating a CPU core, program memory (Flash/ROM), data memory (RAM), and programmable peripherals (timers, ADC, communication blocks). PIC18F-series MCUs use Microchip's enhanced Harvard RISC architecture with 16-bit instructions and 8-bit data, fitting into the broader taxonomy: microcontroller -> embedded processor -> semiconductor IC. They balance low cost, low power, and rich peripherals for high-volume consumer and industrial products. Key features include 128 bytes of EEPROM, seven 10-bit ADC channels, an AUSART serial port, capture/compare/PWM modules, self-programming support, and ICD (In-Circuit Debugger) capability. nanoWatt Technology offers six software-controlled power-managed modes with standby current as low as 0.1 microampere, enabling battery-friendly operation in always-on or sleep-dominant applications. The PIC18F1220 uses a pipelined 8-bit RISC core with 16-bit wide instructions, a hardware multiplier, and a C-compiler-friendly instruction set. The integrated 10-bit ADC (7 channels) supports mixed-signal sensing, while AUSART enables RS-232/RS-485 communication. The 16 I/O pins are 5V-tolerant and source/sink up to 25 mA per pin, suitable for direct LED drive or simple relay/transistor interfaces. Typical applications include consumer appliances, low-end industrial controls, sensor signal conditioning nodes, and battery-powered instrumentation. Its compact 20-pin SSOP footprint and broad peripheral set make it especially attractive where PCB area is constrained but ADC, communication, and PWM are all required. When designing with this device, ensure the ICSP/ICD pins (RB6/RB7) are reserved for programming/debug access or isolated with jumpers to avoid contention with the application circuit. Use Microchip's MPLAB X IDE with XC8 compiler for full toolchain support, and choose the LF variant (PIC18LF1220) for strict 2.0-3.6V-only designs. This page synthesizes distributor pricing, drop-in package-compatible alternatives, and practical design notes not collected in a single place in the manufacturer datasheet.

询价 联系我们
PIC18F1220T-I/ML - 8-bit 40MHz MCU 4KB Flash | Microchip
PIC18F1220T-I/ML

PIC18F1220T-I/ML - 8-bit 40MHz MCU 4KB Flash | Microchip

The Microchip Technology PIC18F1220T-I/ML is an 8-bit PIC microcontroller from the PIC18F family, featuring a 40 MHz operating frequency, 4 KB (2K x 16) Flash program memory, and 256 bytes of RAM, housed in a 28-pin QFN (6x6 mm) package. This industrial-temperature ("-I") tape-and-reel variant delivers enhanced flash programmability and nanoWatt Technology power management with six software-controlled modes for ultra-low standby current down to 0.1 uA. The wide operating voltage range of 2.0V to 5.5V supports both 3.3V and 5V system designs without level translation. An 8-bit microcontroller is a single-chip computer built around an 8-bit data bus and CISC architecture, integrating CPU core, non-volatile program memory, working RAM, peripheral set, and I/O pins into one package. Microcontrollers in this category typically serve as the embedded control brain in low-to-mid complexity products where deterministic timing, low power, and small footprint outweigh the throughput of 32-bit cores. Within the broader taxonomy, PIC18F parts sit at the high-performance end of the 8-bit family, sitting below 16-bit PIC24/dsPIC and 32-bit PIC32M/PIC32MX parts, all under the umbrella of microcontrollers, embedded controllers, and finally semiconductor ICs. Key features include 16 digital I/O pins, a 10-bit analog-to-digital converter, hardware USART, ICSP (In-Circuit Serial Programming) for in-field firmware updates, and an internal 8 MHz RC oscillator with PLL. The device also integrates nanoWatt power-managed modes such as Sleep, Idle, and several software-configurable low-power states ideal for battery-powered applications. The 28-pin QFN package offers a 6x6 mm PCB footprint with an exposed thermal pad for improved thermal dissipation in space-constrained layouts. The PIC18F1220 is built on Microchip's enhanced Harvard architecture, featuring a 16-bit wide instruction word with 8-bit data path, hardware multiplier, and C compiler-friendly instruction set. The enhanced core delivers up to 10 MIPS at 40 MHz while remaining code-compatible with the larger PIC18F family, allowing straightforward migration to higher-pin-count or higher-memory siblings without firmware rework. Typical applications include sensor signal conditioning, low-power remote controls, battery management controllers, HVAC thermostat controls, consumer appliance interfaces, and small appliance motor control where the device's combination of nanoWatt Technology, 10-bit ADC, and compact QFN footprint provides an optimal cost/performance balance. The wide voltage range also suits automotive body electronics and industrial sensor nodes operating from unregulated supplies. When designing with this part, ensure decoupling capacitors (typically 100 nF plus 10 uF bulk) are placed within 5 mm of the VDD/VSS pins and that the exposed thermal pad is soldered to a sufficient ground copper pour to meet thermal and EMI requirements. The PIC18F1220T-I/ML is intended for industrial temperature operation (-40C to +85C). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC18F1220T-I/SO - 8-Bit 40MHz 4KB Flash MCU 18-SOIC | Microchip
PIC18F1220T-I/SO

PIC18F1220T-I/SO - 8-Bit 40MHz 4KB Flash MCU 18-SOIC | Microchip

The Microchip Technology PIC18F1220T-I/SO is an 8-bit PIC18F-series Flash microcontroller running at up to 40 MHz with 4 KB (2K x 16) of program memory and 256 bytes of SRAM, housed in an 18-pin SOIC (SO) package supplied on tape-and-reel (T suffix). It integrates a 10-bit analog-to-digital converter, enhanced flash program memory, and nanoWatt Technology power management with standby current as low as 0.1 µA across an operating voltage range of 2.0 V to 5.5 V. The device is rated -40 °C to +85 °C (industrial grade, I suffix) and supports in-circuit serial programming (ICSP) for field upgrades. Its compact 18-SOIC footprint targets cost-sensitive embedded designs where 8-bit performance, low power, and small PCB area are required. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, data memory, and integrated peripherals such as timers, communication interfaces, and ADCs. The 8-bit category groups MCUs whose internal datapath is 8 bits wide; PIC18F devices extend the 8-bit PIC line with enhanced 16-bit instruction words, hardware multiplier, and a linear program memory map, positioning them between classic baseline PIC and 16-bit dsPIC families. They sit within the broader embedded MCU hierarchy: 8-bit MCU -> microcontroller -> semiconductor -> integrated circuit. Key differentiating features of the PIC18F1220 include 4 KB self-programmable flash, 256 bytes SRAM, 16 I/O lines multiplexed with peripheral functions, 10-bit ADC, capture/compare/PWM modules, enhanced USART, and nanoWatt Technology with six software-controlled power-managed modes. These features reduce bill-of-materials cost by integrating analog, timing, and serial functions on-chip, eliminating external ADC or driver ICs in simple control loops. The PIC18F1220T-I/SO uses a modified Harvard architecture with separate program and data buses, allowing simultaneous instruction fetch and operand access. The enhanced 16-bit instruction set supports hardware multiply, bit manipulation, and direct register addressing, delivering approximately 10 MIPS at 40 MHz. Self-programmable flash allows in-application updates without external programmers, and the nanoWatt sleep modes enable battery-friendly standby operation. Typical applications include consumer appliance control, low-cost sensor signal conditioning, USB-to-UART bridges (with external transceiver), battery-powered instruments, white-goods user interfaces, and industrial monitoring nodes. The combination of nanoWatt low power and an integrated 10-bit ADC makes the device especially attractive for periodic-sampling sensor applications such as temperature, humidity, or simple process-variable readouts. When designing with this part, allocate at least two I/O lines for ICSP (PGD/PGC) plus a dedicated MCLR reset line, even in production firmware, to allow in-circuit firmware updates. Use decoupling of 100 nF plus 10 µF close to VDD, and place the ICSP connector so production programming does not require board removal. This page synthesizes distributor pricing, drop-in same-package alternatives drawn from the Site MPN list and verified web data, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC18F1220T-I/SS - 8-Bit MCU, 4KB Flash, 16 I/O, SSOP-20 | Microchip
PIC18F1220T-I/SS

PIC18F1220T-I/SS - 8-Bit MCU, 4KB Flash, 16 I/O, SSOP-20 | Microchip

The Microchip PIC18F1220T-I/SS is an 8-bit PIC18 high-performance RISC microcontroller with 4KB of Enhanced Flash program memory and 256 bytes of SRAM, housed in a 20-pin SSOP package. The suffix "T" indicates tape-and-reel packaging, the "I" denotes the industrial temperature grade (-40C to +85C), and "/SS" specifies the 20-pin SSOP form factor. It operates at up to 40 MHz (10 MIPS) with a wide supply voltage range of 2.0 V to 5.5 V, making it ideal for both 3.3 V and 5 V systems. A PIC microcontroller is a programmable, single-chip computer built around Harvard architecture - separate program and data buses - and executes one instruction per clock cycle. PIC18F devices sit in Microchip's high-performance 8-bit family, above the legacy PIC16 baseline. PIC18F1220T-I/SS integrates 4 KB flash, 256 B SRAM, 16 digital I/O, a 10-bit ADC, and nanoWatt power management in a compact 20-pin SSOP. This combination targets cost-sensitive embedded applications where 32-bit MCUs are over-spec but more capability than a PIC16 is needed. Key features include nanoWatt Technology with six software-controlled power-managed modes and standby current as low as 0.1 uA, a 10-bit ADC, an internal 31 kHz to 8 MHz oscillator, and an enhanced flash memory with 100,000 erase/write cycles typical endurance. The 10-bit A/D converter offers 7 input channels with acquisition time programmable in 16 levels. An integrated brown-out reset (BOR), watchdog timer, in-circuit serial programming (ICSP), and an 8x8 hardware multiplier round out the peripheral set. Architecturally, the PIC18F1220T-I/SS uses an enhanced 8-bit data path with 16-bit instructions (RISC), 31-level hardware stack, and DC-40 MHz oscillator with 4x PLL option (selectable PLL modes). Two 8-bit timers/counters and one 16-bit timer/counter deliver event timing. Instruction execution throughput is 200 ns at 20 MHz or 100 ns at 40 MHz, which translates to 10 MIPS peak - more than 5x the throughput of a baseline PIC16 at the same clock. Typical applications include battery-powered sensor nodes, low-cost consumer devices, industrial control loops, automotive interior accessories (PIC18F1220-I/SS is the base; Q-grade parts target automotive), and any product needing a small, low-power MCU with on-chip ADC. It is also widely used as a drop-in upgrade for older PIC16 designs needing more code space and peripherals. Design consideration: the SSOP-20 footprint requires careful PCB layout because the 0.65 mm lead pitch demands reflow profile within JEDEC J-STD-020 guidelines and adequate via-in-pad or thermal relief to avoid solder joint fatigue. This page synthesizes distributor pricing, drop-in alternatives (same-brand first, then cross-brand), and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC18F1230-E/P - 8-bit 4KB Flash MCU 40MHz DIP-18 | Microchip
PIC18F1230-E/P

PIC18F1230-E/P - 8-bit 4KB Flash MCU 40MHz DIP-18 | Microchip

The Microchip Technology PIC18F1230-E/P is an 8-bit enhanced flash microcontroller with 4 KB of program memory, packaged in a 18-pin PDIP (DIP-18, 0.300-inch) through-hole form factor. Operating from a 4.2 V to 5.5 V supply and clocked at up to 40 MHz, the device delivers 10 MIPS instruction throughput and integrates a 10-bit A/D converter, a high-performance PWM module, and nanoWatt power management. The PIC18F1230-E/P suffix denotes the Extended (-40C to +125C) operating temperature grade and PDIP package. An 8-bit PIC microcontroller belongs to the class of reduced-instruction-set computing (RISC) microcontrollers based on Harvard architecture, where program and data buses are physically separate. This architecture, combined with a 16-bit instruction word, allows most instructions to execute in a single instruction cycle. PIC microcontrollers sit within the broader category of microcontrollers (MCUs), embedded computing subsystems that integrate CPU, RAM, Flash, and peripherals on a single silicon die. The PIC18F family is Microchip's mid-range 8-bit line, positioned between baseline PIC10/12/16 families and high-pin-count PIC24/dsPIC parts, offering a balance of performance, peripheral integration, and cost for general embedded designs. Key features of the PIC18F1230-E/P include 4 KB Flash program memory, 256 bytes of RAM, 16 I/O pins, a 10-bit A/D converter with multiple channels, an enhanced PWM module with dedicated 14-bit resolution for motor-control-class waveforms, and nanoWatt Technology sleep/Idle modes that reduce quiescent current to microampere levels. The integrated power-management PWM makes this part particularly suited to switched-mode and digital-motor-control applications where a separate PWM controller would otherwise be required. Architecturally, the PIC18F1230 leverages a modified Harvard core with a 16-bit wide program memory bus and an 8-bit data bus, a hardware multiplier for 8x8 unsigned operations in one cycle, and an interrupt controller with multiple priority levels. The 40 MHz oscillator drives a four-phase instruction pipeline, achieving 10 MIPS peak throughput. The 10-bit successive-approximation A/D converter supports up to 8 channels with automatic acquisition timing. Typical applications include DC motor control (BLDC, brushed, and stepper), power-conversion control loops, low-cost PWM-driven LED dimming, and general-purpose embedded control where the integrated high-resolution PWM eliminates the need for an external PWM IC. The 18-pin PDIP footprint also makes it attractive for hobbyist, educational, and through-hole prototyping applications. When designing with the PIC18F1230-E/P, ensure that the ICSP programming header is accessible and that decoupling capacitors (typically 100 nF ceramic) are placed as close as possible to VDD/VSS pins. The Extended temperature grade (-40C to +125C) makes this specific variant suitable for industrial and automotive-under-hood applications, but a less expensive Industrial (-40C to +85C) grade is also available in the same package. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC18F1230-E/SO - 8-bit MCU 4KB Flash 25MHz 18-SOIC | Microchip
PIC18F1230-E/SO

PIC18F1230-E/SO - 8-bit MCU 4KB Flash 25MHz 18-SOIC | Microchip

The Microchip Technology PIC18F1230-E/SO is a high-performance 8-bit PIC18 RISC flash microcontroller integrating 4 KB program Flash, 256 bytes RAM, and a 25 MHz (40 MHz oscillator input) CPU core in a 18-pin SOIC (SO) package. The -E suffix denotes the extended industrial temperature grade (-40C to +125C), making the part suitable for harsh-environment and automotive-under-hood applications. A PIC18F microcontroller is an 8-bit RISC flash MCU belonging to the PIC (Peripheral Interface Controller) family -> 8-bit microcontroller -> microcontroller -> embedded control IC hierarchy. The PIC18F series adds a 16-bit instruction word, hardware multiplier, linear program memory up to 2 MB, and C-friendly architecture to the classic PIC16 baseline, while remaining code-compatible with smaller PIC devices. The 'F' suffix indicates Flash program memory, enabling reprogrammable in-circuit development via ICSP. Key features include 4 KB (2K x 16) self-programmable Flash, 256 bytes RAM, 16 digital I/O pins, a 10-bit A/D converter, an enhanced 14-bit PWM module with dedicated time-base, and nanoWatt power-managed sleep modes that drop Iq below 1 uA. The 8-bit RISC core executes most instructions in a single 100 ns cycle (at 40 MHz oscillator, FOSC/4 = 10 MHz instruction rate). On-chip peripherals include a USART/SCI, MSSP (SPI/I2C), two analog comparators, and a power-managed timer with 4-bit prescaler. Typical applications include motor control (BLDC, brushed DC, stepper), low-end digital power conversion, LED lighting drivers with analog dimming, sensor conditioning front-ends, and small appliance controls. The extended -E temperature grade supports outdoor and industrial installations. When designing with this device, ensure the 5V supply rail has 4.2V-5.5V tolerance under all load transients and that the ICSP programming header is accessible on the PCB. Place a 100 nF decoupling capacitor within 5 mm of the VDD pin and route the MCLR pull-up close to the IC to avoid spurious resets. This page synthesizes distributor pricing, cross-manufacturer drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers evaluate the PIC18F1230-E/SO for both new designs and legacy system refresh.

询价 联系我们
PIC18F1230-I/ML - 8-bit 40MHz MCU 4KB Flash 28-QFN | Microchip
PIC18F1230-I/ML

PIC18F1230-I/ML - 8-bit 40MHz MCU 4KB Flash 28-QFN | Microchip

The Microchip Technology PIC18F1230-I/ML is an 8-bit PIC18 enhanced flash microcontroller with 4 KB of program memory (2K x 16 words), 256 bytes of RAM, and a 40 MHz maximum CPU clock, housed in a 28-pin QFN package (ML, 6x6 mm). The part integrates a high-performance Power Control PWM module, a 10-bit ADC, three analog comparators, a LIN-capable USART, and nanoWatt technology for low-power operation. An 8-bit microcontroller (MCU) is a single-chip processor with an 8-bit data path, integrated flash program memory, RAM, and on-chip peripherals (ADC, PWM, timers, communication ports). MCUs sit within the broader hierarchy: microcontroller -> embedded processor -> semiconductor. They are widely used to sense, decide, and act in embedded systems ranging from appliances and motor drives to automotive body electronics. The PIC18 family specifically targets high-performance 8-bit applications that benefit from RISC-like instruction execution, hardware multiply, and C-friendly architecture. Key features of the PIC18F1230 include nanoWatt technology for dynamic power management (multiple idle/sleep modes), an internal 8 MHz oscillator, an enhanced 14-bit Power Control PWM module optimized for motor control, a 10-bit A/D converter with up to 8 input channels, three on-chip analog comparators, and a LIN-capable Enhanced USART. The 28-QFN (ML) package provides a compact 6x6 mm footprint with an exposed thermal pad, suiting space-constrained PCB layouts while maintaining adequate heat dissipation for the specified operating range. From an architectural standpoint, the PIC18F1230 uses a Harvard-class RISC core with hardware multiply, single-cycle instruction execution at the oscillator frequency (4 TCY per instruction cycle for a 40 MHz oscillator), and separate program/data buses. The 4 KB flash supports self-programming via the ICSP interface, allowing in-field firmware updates. The combination of high-speed PWM, fast comparators, and ADC allows sensorless and sensored motor-control loops to be closed in firmware without external hardware. Typical applications include single-phase and three-phase brushless DC (BLDC) motor control, switched-mode power supply (SMPS) digital control, LIN-based automotive body electronics (window lift, seat, mirror, lighting), sensor fan control, and small appliance drives. Its LIN USART and PWM make it a frequent choice for low-cost automotive node ECUs. When designing with this device, allow a decoupling capacitor (typically 100 nF plus bulk) on every VDD pin as close to the package as possible, and connect the QFN exposed pad to a solid ground plane for thermal and electrical performance. Programming uses Microchip's ICSP interface; plan header access or test points accordingly. This page synthesizes distributor pricing, drop-in PIC18F family alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a faster path from selection to prototype.

询价 联系我们
PIC18F1230-I/P - 8-Bit 40MHz 4KB Flash MCU 18-PDIP | Microchip
PIC18F1230-I/P

PIC18F1230-I/P - 8-Bit 40MHz 4KB Flash MCU 18-PDIP | Microchip

The Microchip Technology PIC18F1230-I/P is an 8-bit PIC18 microcontroller IC featuring 4KB (2K x 16) of Flash program memory, 256 bytes of RAM, and a 40 MHz maximum CPU clock, housed in an 18-pin PDIP through-hole package. The part integrates a 10-bit A/D converter, a high-performance PWM module, nanoWatt Technology power management, and 16 digital I/O pins for mixed-signal embedded control. It operates from a 4.2 V to 5.5 V supply across the industrial -40 °C to +85 °C temperature range. An 8-bit PIC microcontroller is a Harvard-architecture RISC CPU that executes one instruction per clock cycle (excluding branches) and stores its program code in non-volatile Flash, allowing in-system reprogramming via ICSP. The PIC18 family sits above the baseline PIC16 line with deeper pipelining, a wider 16-bit instruction word, and a richer peripheral set, making it the workhorse tier for cost-sensitive motor control and sensor-interface designs. Key specifications include 4 KB Flash (2K x 16 words), 256 bytes of SRAM, 16 GPIO, the integrated 10-bit A/D converter with multiple input channels, a dedicated Power Control PWM (PCPWM) module suited for driving MOSFETs in half-bridge and full-bridge topologies, and nanoWatt power-saving modes (Idle, Sleep, and oscillator switching). The wide 4.2 V - 5.5 V supply range allows direct regulation from a 5 V rail or a USB-powered bus. Architecturally, the PIC18F1230 shares its silicon die and peripheral set with the 8 KB-flash sibling PIC18F1330; the two parts differ only in program-memory density and are otherwise interchangeable on the same PCB. Internally the CPU executes a 16-bit instruction set, the Flash is self-programmable under software control, and the PCPWM block supports complementary outputs with programmable dead-band delay - a feature rarely found on competing 18-pin MCUs. Typical applications include sensor-conditioned motor control (BLDC, brushed DC, and small 3-phase inverters), power-conversion control loops, fan and pump controllers, low-cost SMPS primary-side regulation, and industrial instrumentation front-ends. In these roles the high-performance PWM and on-chip A/D reduce the BOM by eliminating an external gate-driver logic array. Designers should allocate at least 0.1 µF decoupling on VDD and AVSS, follow Microchip's PCB layout recommendations for the analog section to preserve A/D accuracy, and verify that the chosen oscillator mode meets the 40 MHz FOSC limit. The ICSP/ICD interface uses pins RB6 and RB7, which must be left free of any external driver that would prevent in-circuit programming. This page synthesises distributor pricing, drop-in same-package alternatives (PIC18F1330-I/P, PIC18F1220-I/P, PIC18F1320-I/P), and practical design notes that are not found in a single manufacturer datasheet or distributor listing.

询价 联系我们