微控制器

产品（19,000+)

PIC18F47Q83-I/P - 8-bit 64MHz 128KB Flash MCU | Microchip
PIC18F47Q83-I/P

PIC18F47Q83-I/P - 8-bit 64MHz 128KB Flash MCU | Microchip

The Microchip Technology PIC18F47Q83-I/P is an 8-bit PIC microcontroller from the PIC18-Q83 family operating at up to 64 MHz, featuring 128 KB of Flash program memory, 13 KB of SRAM, and 1 KB of Data EEPROM in a 40-pin PDIP through-hole package. The device integrates an extensive set of Core Independent Peripherals (CIPs) including a 12-bit ADC, a 12-bit DAC, a Digital Signal Modulator (DSM), multiple PWM modules, and a built-in CAN 2.0B controller for industrial and automotive networking. An 8-bit microcontroller (MCU) is a single-chip computer that uses an 8-bit data bus architecture, combining a CPU, memory, and configurable peripherals on a single silicon die. Within the broader semiconductor taxonomy, an MCU belongs to the microcontroller family, which sits under embedded processors and semiconductors. The PIC18 family specifically targets cost-optimized general-purpose embedded designs that benefit from deterministic instruction execution and a rich peripheral set without the overhead of higher-bit architectures. Key features of the PIC18F47Q83 include up to 36 I/O pins, multiple communication interfaces (I2C, SPI, UART), DMA, two comparators, two watchdog timers, and nine timers. The integrated CAN module makes it well-suited for industrial nodes that previously required an external CAN transceiver companion IC, while the 12-bit ADC and DAC reduce the bill of materials for sensor-conditioning and analog-output designs. The architecture uses Microchip's enhanced mid-range 8-bit CPU core with hardware multiply and a 16-bit instruction word, providing a balance of code density and execution speed. With 128 KB of self-programmable Flash, the device supports field firmware updates via the bootloader-friendly architecture and ICSP (In-Circuit Serial Programming) interface. Typical applications include industrial sensor nodes, automotive body and lighting controllers (CAN-connected), appliance control boards, building automation, and low-cost instrumentation. The wide operating voltage range and integrated peripherals make it especially useful in designs that previously required multiple discrete ICs to achieve CAN connectivity plus analog signal conditioning. When designing with this device, plan for a robust decoupling strategy (100 nF plus 10 uF bulk), keep CAN bus traces short and impedance-controlled, and reserve the ICSP/PGD/PGC pins for in-system programming access. The PDIP-40 footprint is breadboard-friendly, simplifying prototyping before moving to surface-mount variants. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that are not consolidated on a single datasheet page, giving engineers a faster path from selection to prototype.

询价 联系我们
PIC18F47Q83-I/PT - 64MHz 128KB Flash CIP MCU | Microchip
PIC18F47Q83-I/PT

PIC18F47Q83-I/PT - 64MHz 128KB Flash CIP MCU | Microchip

The Microchip Technology PIC18F47Q83-I/PT is a 64 MHz 8-bit PIC18 microcontroller with 128 KB Flash, 13 KB SRAM and 1 KB EEPROM, integrated into a 44-pin TQFP (10x10 mm) industrial-temperature package. It combines the PIC18 enhanced mid-range core with Core Independent Peripherals (CIPs) and a hardware CAN FD controller for robust in-vehicle and industrial networking. The device operates from 2.5 V to 5.5 V across the industrial -40C to +85C range and is housed in a TQFP-44 package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and peripheral subsystems on one silicon die. The PIC18 architecture belongs to the modified Harvard 8-bit family, where program and data memory use separate buses for predictable instruction throughput. Within the broader taxonomy, the PIC18F47Q83 sits between general-purpose 16-bit MCUs and 32-bit ARM Cortex-M parts - offering higher peripheral integration than baseline PIC16 devices while keeping the deterministic interrupt model of the PIC18 core. The PIC18F47Q83 targets CAN-connected and CIP-driven designs where software offloading to hardware saves code space and CPU cycles. Key features include 128 KB self-programmable Flash with device firmware upgrade support, 13 KB SRAM, 1 KB EEPROM, 36 MHz internal oscillator (HFINTOSC) and PLL, hardware CAN FD peripheral, up to 35 channels of 12-bit ADC with computation, 5-bit/8-bit DAC, op-amp core, configurable logic cells (CLC), DMA, multiple UART/SPI/I2C, and 10-bit/12-bit PWM with complementary outputs. The 44-pin TQFP exposes 36 I/O pins with 5V-tolerant digital interfaces. Typical applications include industrial automation controllers, automotive body and sensor ECUs, appliance and white-goods control boards, IoT gateways with CAN node connectivity, and battery management systems requiring deterministic CAN traffic. When designing with this device, ensure proper decoupling (100 nF ceramic plus bulk) on each VDD/VSS pair, follow Microchip AN1255 for Q83 family CIP configuration, and reserve a dedicated CAN transceiver footprint such as the MCP2562FD.

询价 联系我们
PIC18F47Q83T-I/PT - 128KB Flash 8-bit MCU w/ CAN | Microchip
PIC18F47Q83T-I/PT

PIC18F47Q83T-I/PT - 128KB Flash 8-bit MCU w/ CAN | Microchip

The Microchip Technology PIC18F47Q83T-I/PT is a 64 MHz 8-bit PIC microcontroller with 128 KB Flash, 13 KB SRAM, and 1 KB EEPROM, housed in a 44-pin TQFP (10x10 mm) tape-and-reel package. It integrates Core Independent Peripherals (CIPs) including a CAN FD controller, a 12-bit ADC with Computation (ADC2), a 5-bit DAC, DSM (Data Signal Modulator), PWM modules, and CIPS, alongside I2C, SPI, and UART serial interfaces. An 8-bit PIC microcontroller (MCU) is a Harvard-architecture RISC processor widely used in embedded control for its deterministic instruction execution, low power consumption, and rich peripheral integration. Within the broader MCU taxonomy, 8-bit MCUs sit below 16-bit and 32-bit Cortex-M devices in computational capability but excel in cost-sensitive, real-time control applications. The PIC18 family adds enhanced peripherals, larger memory, and C compiler support (MPLAB XC8) while remaining pin-compatible with the legacy PIC16 baseline, making it a workhorse for industrial, automotive, and IoT designs. Key features of the PIC18F47Q83T-I/PT include 128 KB self-programmable Flash with device ID protection, a 10-bit slope ADC2 with automated averaging, oversampling, and threshold comparison, a 5-bit DAC with internal reference, and four 16-bit PWM outputs. The device also exposes 36 digital I/O pins, four CWG (Complementary Waveform Generator) channels, and a Hardware Limit Timer for deterministic motor and lighting control. Operating voltage is 2.5 V to 5.5 V, and the operating temperature range is -40C to +85C (industrial grade). The PIC18F47Q83 architecture combines the legacy PIC18 instruction set with modern CIP blocks, allowing developers to offload logic such as signal conditioning, motor commutation, and protocol handling from the CPU. The device supports up to 64 MHz operation from an internal 64 MHz HFINTOSC, eliminating external crystals in many designs, and integrates a CAN FD peripheral for automotive and industrial networking. Typical applications include CAN node endpoints in industrial automation, BLDC motor control, LED lighting drivers, IoT sensor hubs, and USB-to-CAN bridges. The combination of CAN FD, PWM, and ADC2 with computation makes the PIC18F47Q83 particularly well-suited to sensor-rich, real-time control systems. When designing with this MCU, budget carefully for the 44-pin TQFP footprint's thermal envelope. Although the part is low-power (typical active current below 10 mA at 64 MHz), high GPIO toggle rates and ADC sampling can raise junction temperature in enclosed housings. Decouple VDD with 100 nF ceramic caps adjacent to each power pin, and reserve RA5 as MCLR with a 10 kohm pull-up per Microchip's recommendation. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet, enabling faster sourcing and design decisions.

询价 联系我们
PIC18F47Q84-E/P - 64MHz 8-bit MCU, 128KB FLASH, CAN-FD | Microchip
PIC18F47Q84-E/P

PIC18F47Q84-E/P - 64MHz 8-bit MCU, 128KB FLASH, CAN-FD | Microchip

The Microchip PIC18F47Q84-E/P is an 8-bit RISC microcontroller in the PIC18-Q84 family, featuring a PIC18 CPU core running up to 64MHz, 128KB (64K x 16) of FLASH program memory, 12.8KB of data RAM, and 1024 Bytes of data EEPROM, all housed in a 40-pin PDIP through-hole package. The part includes 36 I/O lines, an integrated 12-bit ADC, 8 DMA channels, and 11 timer channels, and operates from 1.8V to 5.5V across the -40C to +125C industrial temperature range. What is a PIC18-Q84 microcontroller? The PIC18-Q84 is Microchip's cost-optimized 8-bit MCU family that combines an extensive array of Core Independent Peripherals (CIPs) with a Controller Area Network Flexible Data-rate (CAN FD) controller. CIPs are hardware peripherals that can execute tasks autonomously without CPU intervention, freeing the core for application code. Within the broader taxonomy, this places the part at: PIC18F47Q84 -> PIC18-Q84 family -> PIC18 microcontrollers -> 8-bit MCUs -> embedded controllers -> semiconductor IC. These features make PIC18-Q84 devices well suited for automotive body electronics, industrial control, and smart-sensor networks. Key differentiating features include integrated CAN FD for high-throughput automotive networking, XLP (eXtreme Low Power) technology for sleep currents in the nanoampere range, 8 DMA channels that offload peripheral-to-memory transfers, and a CLC (Configurable Logic Cell) plus multiple waveform generators that implement custom glue logic in hardware without external gates. The PIC18-Q84 architecture pairs the legacy PIC18 instruction set with modern peripherals such as a 12-bit differential ADC, complementary waveform generators for motor or power-converter control, and zero-cross detection. Compared with older PIC18F46K22-class parts, the Q84 adds CAN FD, DMA, and significantly higher RAM, enabling larger protocol stacks and richer state machines on the same 8-bit core. Typical applications for PIC18F47Q84-E/P include CAN-FD body-control modules in vehicles, industrial PLC digital I/O cards, building-automation sensor hubs, BLDC/PMSM motor-control subsystems, and battery-management secondary protection boards. The combination of 36 I/O, 12-bit ADC, and CAN FD in a 40-pin PDIP makes it convenient for through-hole prototyping and field-service replacement boards. When designing with this device, plan the ICSP clocking and ICSPDAT/ICSPCLK shared with the I/O pins, and use the DMA-driven ADC for high-throughput sampling. The -E suffix denotes the -40C to +125C extended temperature grade, suitable for underhood and outdoor enclosures. This page synthesizes verified distributor pricing, drop-in alternative parts sharing the 40-pin PDIP footprint, and practical design notes not assembled on the manufacturer datasheet.

询价 联系我们
PIC18F47Q84-E/PT - 8-bit 64MHz MCU, 128KB Flash, CAN FD | Microchip
PIC18F47Q84-E/PT

PIC18F47Q84-E/PT - 8-bit 64MHz MCU, 128KB Flash, CAN FD | Microchip

The Microchip Technology PIC18F47Q84-E/PT is an 8-bit PIC18 microcontroller running at up to 64 MHz with 128 KB of Flash, 13 KB of RAM, 1 KB of EEPROM and integrated Core Independent Peripherals (CIPs) plus a CAN FD controller, all packaged in a 44-pin TQFP (10x10 mm). It targets cost-optimised embedded designs that need automotive-grade connectivity and high analog integration in an industrial temperature grade. An 8-bit PIC microcontroller is a Harvard-architecture MCU built around an enhanced PIC18 CPU core, combining deterministic real-time control with rich on-chip peripherals. The PIC18-Q84 family expands the 8-bit MCU portfolio by pairing CAN Flexible Data Rate (CAN FD) networking with CIPs such as 12-bit ADC, 5-bit DAC, DSM, configurable CLC, PWM, and math accelerator. Within the broader taxonomy this device sits as: PIC18F47Q84 -> PIC18F47Q84 family -> PIC18-Q84 series -> PIC18 microcontrollers -> 8-bit MCUs -> Microcontrollers (MCU) -> Integrated Circuits (ICs) -> Semiconductors. Key features include 128 KB (64K x 16) self-programmable Flash, 13 KB SRAM, 1 KB EEPROM, a 12-bit ADC with computation, a 5-bit DAC, DSM, multiple PWM modules, configurable logic cells, I2C/SPI/UART interfaces, JTAG boundary scan, and a math accelerator. The CAN FD peripheral supports higher bandwidth than classic CAN, enabling modern automotive and industrial sensor networks while the CIPs offload tasks from the CPU. The device operates from 1.8 V to 5.5 V across the -40 C to +125 C industrial temperature range. The 64 MHz internal oscillator combined with peripheral clock scaling allows fine-grained power tuning through nanoWatt XLP technology. The 44-pin TQFP (10x10 mm) package exposes 36 I/O pins with multiple interrupt-on-change capable ports. Typical applications include automotive body and sensor nodes, CAN FD sensor networks, industrial automation controllers, building automation, low-power IoT gateways, and consumer appliances requiring deterministic control with networking. The combination of CAN FD and CIPs reduces external component count and BOM cost. When designing with this part, allocate adequate decoupling (100 nF + bulk) near each VDD/VSS pair, follow the oscillator layout guidance in section 4 of the datasheet (avoid noisy traces near OSCI/OSCO), and ensure CAN bus termination and shielding match ISO 11898-1 requirements for reliable operation. This page synthesises distributor pricing, drop-in alternatives, application notes and practical design guidance not found in the manufacturer datasheet alone, giving engineers a single reference for sourcing and integrating the PIC18F47Q84-E/PT.

询价 联系我们
PIC18F47Q84-I/P - 8-Bit 64MHz 128KB Flash MCU w/ CAN FD | Microchip
PIC18F47Q84-I/P

PIC18F47Q84-I/P - 8-Bit 64MHz 128KB Flash MCU w/ CAN FD | Microchip

The Microchip Technology PIC18F47Q84-I/P is an 8-bit PIC18 microcontroller with 128KB Flash, 13KB RAM, 1KB EEPROM and integrated CAN FD controller, housed in a 40-pin PDIP (DIP-40) through-hole package. It operates up to 64MHz internal clock and includes a 12-bit ADC with computation (ADCC), a 5-bit DAC, a DSM (Data Signal Modulator), multiple CCP/PWM channels, plus I2C/SPI/UART communication peripherals. This -I/P variant is the industrial temperature grade (-40C to +85C). An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, program memory (Flash), data memory (SRAM), non-volatile EEPROM, and a rich set of on-chip peripherals. The PIC18 family belongs to the Modified Harvard architecture class of microcontrollers, executing one instruction per clock cycle (except branches) for predictable real-time performance. Within the broader taxonomy: MCU -> 8-bit MCU -> PIC18 family -> PIC18-Q84 sub-family (which is optimized for CAN-FD connectivity and Core Independent Peripherals). Key features of the PIC18F47Q84 include Core Independent Peripherals (CIPs) such as CLC, CCP, PWM, NCO, CWG, and DSM that operate without CPU intervention - reducing firmware complexity and BOM cost. The 12-bit ADCC (ADC with Computation) provides oversampling and automated averaging/threshold comparison. CAN FD enables higher throughput automotive/industrial networking at up to 5 Mbps nominal bit rate. The device also integrates two UARTs, two SPI, two I2C, and a generous complement of timers. Architecturally, the PIC18F47Q84 is built on an enhanced PIC18 core with a hardware multiplier, 31-level stack, and a vectored interrupt controller supporting prioritized interrupts. Its CIPs are interconnected through a flexible signal routing matrix, allowing hardware-based state machines, waveform generation, and sensor signal conditioning (via the DSM module). The wide 1.8V-5.5V VDD range (with integrated voltage regulator) supports both 3.3V and 5V designs. Typical applications include CAN-FD automotive body and chassis ECUs, industrial sensor hubs, motor control (BLDC/PMSM), building automation nodes (HVAC/lighting), USB-to-CAN bridges, and battery management systems. The 40-pin PDIP package is especially suited for development, prototyping, and through-hole assembly where socket-based or hand-soldered replacement may be desired. When designing with this device, ensure decoupling capacitor placement (100nF close to VDD/AVDD/VBAT plus bulk 1-10uF) per the datasheet's PCB layout guidelines. Configure the ICD pins (ICSPCLK/ICSPDAT) for in-circuit serial programming - the device supports both PICKit and MPLAB debug tools. This page synthesizes distributor stock, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC18F47Q84-I/PT - 64MHz 128KB Flash CAN-FD 8-bit MCU | Microchip
PIC18F47Q84-I/PT

PIC18F47Q84-I/PT - 64MHz 128KB Flash CAN-FD 8-bit MCU | Microchip

The Microchip Technology PIC18F47Q84-I/PT is an 8-bit PIC18 microcontroller with 128 KB Flash, 13 KB RAM, and 1 KB EEPROM, housed in a 44-pin TQFP (10x10 mm) package. It integrates Controller Area Network with Flexible Data Rate (CAN FD), Core Independent Peripherals (CIPs), a 12-bit ADC, 5-/10-bit DAC, DSM (Digital Signal Modulator), and Configurable Logic Cells (CLC), targeting connected industrial and automotive nodes. The PIC18F47Q84 family is described by Microchip as "cost optimized MCUs with time-saving CIPs in up to 48 pins" with explicit CAN FD support. An 8-bit microcontroller (MCU) is a programmable processor that integrates CPU, non-volatile program memory (Flash), volatile data memory (SRAM), EEPROM, and a set of on-chip peripherals into a single IC. Within the broader taxonomy, an MCU belongs to the embedded controller class, which sits beneath microprocessors (no on-chip memory) and above digital logic ICs. The PIC18 core is a Harvard-architecture 8-bit CPU with a 16-bit instruction word, providing higher code density than baseline PIC16 cores and one of the longest-lived 8-bit MCU architectures in the industry. The PIC18F47Q84 adds the CIP block set that lets hardware peripherals operate without CPU intervention, freeing the core for communications or higher-level tasks. Key features of the PIC18F47Q84-I/PT include a 64 MHz internal oscillator, up to 16 MIPS throughput, hardware CAN FD controller, four 16-bit timers, multiple PWM/SCCP modules, 12-bit ADC with computation, two 5-/10-bit DAC outputs, and peripheral pin select (PPS) for flexible signal routing. The 44-pin TQFP package exposes up to 36 digital I/O pins, supports 5 V operation, and is qualified for industrial temperature range (-40C to +85C for the -I suffix). Architecturally, the PIC18F47Q84 uses the enhanced mid-range core (PIC18) with a hardware multiplier, hardware divider, and 31-level stack. Power management includes nanoWatt XLP technology with multiple idle/sleep modes, brown-out reset (BOR), and low-power watchdog timer, making it suitable for battery-powered sensor nodes and always-on industrial endpoints. Typical applications include CAN FD body and chassis nodes in vehicles, industrial sensor hubs with fieldbus, building automation HVAC controllers, motor control front-ends, USB-CAN bridges, and general-purpose embedded control. The wide operating voltage range and the CIP-driven peripheral set also suit mains-powered white goods and appliance control boards. Design consideration: when routing CAN FD signals, keep the bus stubs short and place the optional CAN transceiver on the same PCB edge as the bus connector. Use the device's internal 64 MHz oscillator for clock accuracy, or provide an external crystal if CAN FD timing margins are critical to your network design. This page synthesizes distributor pricing, drop-in alternatives from the same PIC18-Q84 family, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC18F47Q84T-I/PT - 64MHz 8-bit CAN-FD MCU 128KB Flash | Microchip
PIC18F47Q84T-I/PT

PIC18F47Q84T-I/PT - 64MHz 8-bit CAN-FD MCU 128KB Flash | Microchip

The Microchip Technology PIC18F47Q84T-I/PT is a 64 MHz 8-bit PIC18 microcontroller integrating 128 KB Flash, 13 KB SRAM, and 1 KB EEPROM with CAN Flexible Data Rate (CAN FD) connectivity in a 44-pin TQFP (10x10 mm) package. It combines Core Independent Peripherals (CIPs) such as a 12-bit ADC with Computation, 12-bit DAC, DSM, PWM, and CIPS I/O with 1.8 V to 5.5 V wide operating voltage. An 8-bit microcontroller (MCU) is a compact computing-on-a-chip that integrates a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and a rich set of peripherals into a single IC. PIC18-series 8-bit MCUs from Microchip sit within the broader 8-bit PIC MCU family (PIC10 -> PIC12 -> PIC16 -> PIC18) and the wider category of embedded microcontrollers, which is a sub-category of microprocessors and semiconductors. The PIC18 architecture is well-suited for real-time control due to its deterministic instruction set, prioritized interrupts, and powerful peripheral set. Key features include an integrated CAN FD controller for high-throughput automotive and industrial networking, a 12-bit ADC with Computation (ADC2) for automated analog signal conditioning without CPU intervention, a 12-bit DAC for waveform generation, and a Device Service Manager (DSM) for tethered system updates. The high-pin-count TQFP-44 package exposes multiple UART, SPI, I2C, and PWM channels, enabling flexible multi-sensor and multi-actuator designs. The architecture is built on an enhanced PIC18 Harvard core with hardware multiply and a 31-level stack, paired with a peripheral pin-select (PPS) engine that remaps digital I/O functions to almost any I/O pin. This decoupling of peripheral and pin assignment dramatically simplifies PCB routing when system requirements change late in the design cycle. Typical applications include automotive body and chassis networks with CAN FD, industrial sensor hubs, motor control, building automation, and low-power IoT edge nodes. The wide 1.8 V to 5.5 V range allows direct Li-ion battery and 3.3 V/5 V mixed-rail operation. When designing with this device, allocate sufficient decoupling on VDD/AVDD pins and use Microchip's MPLAB X IDE with XC8 compiler and MCC code configurator. Plan CAN FD bus termination and bit-timing per ISO 11898-1, and use the integrated DSM module for secure in-field firmware updates. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC18F55K42-E/MV - 8-bit MCU, 32KB Flash, 48-pin UQFN | Microchip
PIC18F55K42-E/MV

PIC18F55K42-E/MV - 8-bit MCU, 32KB Flash, 48-pin UQFN | Microchip

The Microchip PIC18F55K42-E/MV is an 8-bit PIC18 RISC microcontroller with 32KB Flash, 2KB SRAM and 256B EEPROM, housed in a 48-pin UQFN-EP package with operating voltage range of 2.5V/3.3V/5V. According to the Microchip product page, it integrates core-independent peripherals (CIPs), intelligent analog (12-bit ADC2, 5-bit DAC, comparators), DMA, vector interrupts, and Device Information Area (DIA) storage. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), and a rich set of on-chip peripherals. The PIC18 family uses Microchip's enhanced 8-bit RISC architecture with hardware multiplier and 16-bit instructions, sitting above baseline PIC10/12/16 parts in capability. The K42 sub-family targets low-power XLP-class designs while adding a high-resolution PWM and 12-bit ADC2 analog front-end, making it a power-management IC class part for embedded control nodes. Key features include 32KB self-programmable Flash with code protection, configurable oscillator modes up to 64MHz internal, 12-bit ADC2 with Computation (ADCC) capability, 10-bit DAC, multiple Zero-Cross Detect comparators, Complementary Waveform Generator (CWG), and 4 Slices of Capture/Compare/PWM (CCP). Communications include UART, I2C, SPI, and CLC (Configurable Logic Cell) for hardware glue logic. Architecturally, the PIC18F55K42-E/MV uses an 8-bit data path with a 16-bit instruction word Harvard architecture, featuring 31-level stack hardware call/return, priority-vector interrupt controller with shadow register sets, and Peripheral Pin Select (PPS) for flexible I/O mapping. The 12-bit ADCC provides averaging, oversampling, and burst-averaging modes that offload CPU cycles. Typical applications include IoT sensor nodes, BLDC motor control (FOC firmware) using the CWG and PWM peripherals, industrial HMI/touch sensing, and home appliance control panels. The wide-voltage 2.3V–5.5V range with XLP eXtreme Low Power support enables long battery-life designs. When designing with this MCU, reserve PPS mapping early because most peripherals share pins. The UQFN-EP package requires thermal vias under the exposed pad to dissipate up to 0.6W and meet solder-joint reliability. This page synthesizes Microchip product-page data, drop-in alternatives within the PIC18FxxK42 family, and practical design notes not consolidated on a single distributor page.

询价 联系我们
PIC18F55K42-E/PT - 32KB Flash 8-bit MCU 48-TQFP | Microchip
PIC18F55K42-E/PT

PIC18F55K42-E/PT - 32KB Flash 8-bit MCU 48-TQFP | Microchip

The Microchip Technology PIC18F55K42-E/PT is an 8-bit PIC microcontroller built on the enhanced mid-range core with a 64 MHz CPU speed, integrating 32 KB of Flash, 2 KB of SRAM, and 256 bytes of EEPROM in a 48-pin TQFP-EP (7x7 mm) package with exposed thermal pad. It belongs to the PIC18FxxK42 family and features the eXtreme Low Power (XLP) technology plus intelligent analog and Core Independent Peripherals (CIPs). An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash/RAM/EEPROM), peripherals, and I/O on one die. The PIC18FxxK42 family sits within the 8-bit PIC18 hierarchy under Microchip's broader MCU portfolio, targeting cost-sensitive embedded designs where deterministic real-time behavior, low power, and rich analog integration matter more than raw computational throughput. Designers select 8-bit PICs when they need reliable behavior in noisy environments with minimal external components. Key specifications include a 12-bit ADC with Computation (ADC2), a 5-bit DAC, two comparators with selectable references, multiple PWM modules with complementary outputs, DMA controller, Memory Access Partition (MAP) for bootloader write protection, Device Information Area (DIA), vectored interrupts with programmable priority, and a programmable Interrupt Vector Table. The 48-TQFP-EP package exposes a thermal pad enabling higher dissipation in industrial temperature grades. The architecture features the enhanced mid-range 8-bit CPU executing most instructions in a single cycle, yielding up to 16 MIPS at 64 MHz. Hardware DMA moves data between memory and peripherals without CPU intervention, freeing the core for application logic. CIPs such as the CWG, NCO, and configurable logic cells let signal generation, timing, and glue logic run autonomously. Typical applications include industrial sensing nodes, motor control with FOC, IoT edge sensor hubs, consumer white goods, smart metering, and automotive body controllers. The combination of vectored interrupts and CIPs makes the part well suited to deterministic control loops. The 32 KB Flash and 256-byte EEPROM suit moderate code sizes with runtime-tunable parameters. When designing with the PIC18F55K42-E/PT, place decoupling capacitors close to every VDD/VSS pair, route the exposed pad to a continuous ground copper pour for thermal relief, and reserve the MAP region early in firmware planning if a bootloader is required. This page synthesizes distributor pricing, cross-family alternatives within the PIC18 K42/Q43 generations, and practical design notes not consolidated in the manufacturer datasheet.

询价 联系我们
PIC18F55K42-I/MV - 8-Bit 64MHz MCU, 32KB Flash, 48-UQFN | Microchip
PIC18F55K42-I/MV

PIC18F55K42-I/MV - 8-Bit 64MHz MCU, 32KB Flash, 48-UQFN | Microchip

The Microchip Technology PIC18F55K42-I/MV is an 8-bit RISC microcontroller from the PIC18 XLP family, delivering 64 MHz CPU performance with 32 KB Flash, 2 KB SRAM, and 256 bytes EEPROM in a 48-pin UQFN (6x6 mm) package with exposed pad. It integrates Core Independent Peripherals (CIPs), a 12-bit ADC2 with Computation, DMA, Vector Interrupts, Memory Access Partition (MAP), Device Information Area (DIA), a 5-bit DAC, comparators, and PWM peripherals on-chip. An 8-bit PIC microcontroller is a Harvard-architecture RISC CPU with separate program and data buses, optimized for deterministic real-time control. Within Microchip's taxonomy the part belongs to PIC18 (high-performance 8-bit) -> PIC microcontroller -> microcontroller -> embedded controller -> semiconductor. The XLP (eXtreme Low Power) family extends this lineage with nanoWatt sleep modes that allow battery-powered nodes to remain active for years on a single cell. Key differentiating features include DMA-capable peripherals that move data without CPU intervention, a vectored interrupt controller with two programmable priority levels, two-level hardware context saving, and CIPs such as CLC, NCO, PWM and the configurable logic cell that let designers build state machines in hardware. The 12-bit ADC2 includes automated averaging, threshold comparison, and zero-crossing detection that offload typical signal-chaining math from the core. The architecture uses a 16-bit instruction word with 8-bit data path and an internal 64 MHz oscillator; instruction execution is four clock cycles. The MV package suffix denotes the 48-pin UQFN (MV) industrial-grade (-40 C to +85 C) variant, distinguished from the low-power PIC18LF55K42 sibling only by its operating voltage range (2.3-5.5 V vs 1.8-3.6 V). Hardware CTE (code-protection) and ICD/ICSP debug pins are present. Typical applications include consumer appliance control, IoT sensor hubs, low-power wireless gateways (paired with RN2483 or MRF24XA), USB-CDC human-interface devices, industrial LED drivers, and small motor-control BLDC fans. The high pin count makes the device well-suited to systems that previously required 40-pin parts but now need more I/O for capacitive touch or segmented displays. A practical design tip: place a 100 nF decoupling capacitor on every VDD/AVDD pair and a bulk 10 uF near the package exposed pad; the EP must be soldered to the ground plane for thermal dissipation and signal integrity. Use the MAP feature to lock the bootloader region from accidental erase. This page consolidates current distributor pricing, drop-in alternatives, and practical design notes not gathered in the manufacturer datasheet alone, allowing engineers to evaluate the PIC18F55K42-I/MV against modern 8-bit and 32-bit alternatives before committing to a BOM line.

询价 联系我们
PIC18F55K42-I/PT - 8-Bit 64MHz 32KB Flash MCU 48-TQFP-EP | Microchip
PIC18F55K42-I/PT

PIC18F55K42-I/PT - 8-Bit 64MHz 32KB Flash MCU 48-TQFP-EP | Microchip

The Microchip Technology PIC18F55K42-I/PT is a 48-pin PIC18 XLP 8-bit microcontroller built on a RISC architecture with a 64 MHz CPU speed (16 MIPS), integrating 32 KB Flash, 2 KB SRAM, 256 B EEPROM, and a 12-bit ADC with computation (ADC2) in a 48-pin TQFP-EP (7x7 mm) package. As part of the PIC18FxxK42 family, the device combines core independent peripherals (CIPs), intelligent analog, and XLP extreme low-power technology in a single chip, targeting both battery-powered and line-powered embedded designs. A PIC microcontroller (Programmable Interface Controller, or MCU) is a compact, low-cost, low-power embedded computer built around a Harvard-architecture RISC core with on-chip Flash, RAM, EEPROM, and a peripheral set (timers, ADC, communications). It belongs to the microcontroller > embedded MCU > semiconductor hierarchy and serves as the central processing unit of countless consumer, industrial, automotive, and IoT systems. PIC18F devices are Microchip's mid-range 8-bit family with 16-bit instructions and rich interrupt handling, bridging the gap between PIC16 baseline parts and PIC24/dsPIC 16-bit devices. Key features of the PIC18F55K42 include 49 digital I/O pins, multiple serial interfaces (UART, SPI, I2C), 12-bit ADC2 with up to 43 analog channels, multiple 8/16-bit timers, DMA controller, vectored interrupt controller, and an on-chip 64 MHz internal oscillator. The XLP technology delivers nanoWatt sleep currents suitable for battery applications, while core independent peripherals (CLC, NCO, PWM, SMT, CCP) can operate without CPU intervention. Typical applications include industrial sensor nodes, low-power IoT edge devices, home appliance control boards, automotive body and lighting modules, USB/HID peripherals, and consumer electronics requiring 5 CAN communication over multiple serial protocols. The wide 2.5 V to 5.5 V supply range and small TQFP-EP footprint simplify layout in space-constrained multi-layer PCBs. When designing with the PIC18F55K42-I/PT, allocate adequate ground copper under the exposed pad (EP) to dissipate package thermal power and to provide a low-impedance ground return. Use Microchip's MPLAB X IDE and XC8 compiler for code development; the device is supported by all major PIC programmers/debuggers including ICD 4, PICkit 4, and MPLAB SNAP. This page synthesizes verified distributor pricing, drop-in same-package alternatives (PIC18F46K42, PIC18F56K42, PIC18F57K42 from the same family), and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC18F55K42T-I/MV - 32KB Flash 8-bit MCU, 48-UQFN | Microchip
PIC18F55K42T-I/MV

PIC18F55K42T-I/MV - 32KB Flash 8-bit MCU, 48-UQFN | Microchip

The Microchip Technology PIC18F55K42T-I/MV is an 8-bit PIC microcontroller in the PIC18 XLP 18K family, featuring 32KB Flash, 2KB RAM, and 256B EEPROM, packaged in a 48-pin UQFN (6x6 mm) with exposed pad. It operates at up to 64MHz across a 2.5V to 5.5V supply range and is supplied on tape and reel (T-I/MV suffix). This device integrates rich core-independent peripherals including DMA, vector interrupts, Memory Access Partition (MAP), Device Information Area (DIA), 12-bit ADC2, 5-/8-bit DAC, comparators with hysteresis, Zero-Cross Detect (ZCD), and a configurable Fixed Voltage Reference (FVR) at 1.024V, 2.048V, and 4.096V levels. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile data memory (RAM), small EEPROM for settings, and a rich set of on-chip peripherals such as timers, ADCs, communication controllers and interrupt logic. Within the broader taxonomy, the PIC18F55K42 belongs to the PIC18 8-bit RISC family, which itself sits under the Microchip 8-bit MCU line, ultimately a subset of microcontrollers -> microprocessors -> semiconductor devices. This category hierarchy helps place the part in the engineering knowledge graph alongside competing 8-bit families such as AVR and 8051 cores. Key differentiating features include XLP (eXtreme Low Power) technology with nanoWatt XLP sleep currents, programmable DMA for background data movement that offloads the CPU, vectored interrupts with hardware context saving, and CIP (Core Independent Peripherals) such as the 12-bit ADC2 with computation, CWG (Complementary Waveform Generator) and NCO (Numerically Controlled Oscillator). These features let designers implement complex timing, signal generation and sensor-processing tasks without CPU intervention. Architecturally, the part is built on an enhanced PIC18 Harvard RISC core with a 16-bit instruction word and 8-bit data path, augmented by a peripheral bus for DMA. The 64MHz internal oscillator (with PLL) provides instruction cycle throughput of 16 MIPS, while the 12-bit ADC2 supports up to 35 input channels depending on package, enabling direct interface to multiple analog sensors in industrial and consumer applications. Typical applications include industrial control panels, home appliance user interfaces, low-power IoT sensor nodes, automotive body and interior modules, LED lighting controllers, and small motor control boards. The wide 2.5V-5.5V supply range allows direct operation from a 3.3V or 5V rail, including battery or USB-derived supplies, while the exposed-pad UQFN package gives good thermal performance for sustained peripheral activity. When designing with this MCU, ensure the exposed pad is soldered to a sufficient copper pour for thermal relief and ground reference. Use the MAP feature to protect bootloader regions from accidental application writes, and leverage DMA to keep the CPU in XLP sleep for power-critical battery applications. The T-I/MV suffix indicates tape-and-reel packaging in the 48-pin UQFN. This page synthesizes distributor pricing, drop-in alternatives from the same PIC18 K42 family, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC18F55Q43-E/6LX - 32KB Flash 8-bit MCU w/ 12-bit ADCC | Microchip
PIC18F55Q43-E/6LX

PIC18F55Q43-E/6LX - 32KB Flash 8-bit MCU w/ 12-bit ADCC | Microchip

The Microchip Technology PIC18F55Q43-E/6LX is an 8-bit PIC microcontroller in the PIC18-Q43 family with 32 KB Flash, 2 KB SRAM, and a 64 MHz CPU clock, housed in a 48-pin VQFN (6x6 mm) package. It integrates a 12-bit Analog-to-Digital Converter with Computation (ADCC), a 12-bit DAC, three 16-bit PWMs, six DMA channels, five UARTs, and Configurable Logic Cells (CLCs) for hardware-level customization. A PIC microcontroller (Programmable Integrated Circuit MCU) is a compact single-chip computer that combines a CPU, Flash program memory, SRAM, and configurable peripherals on one silicon die. The PIC18 family sits in Microchip's 8-bit portfolio between the entry-level PIC16 and the 16-bit dsPIC families, offering a balanced mix of low cost, deterministic interrupt handling, and rich peripheral integration. It belongs to the broader category hierarchy MCU -> microcontroller -> embedded processor -> semiconductor IC. The Q43 sub-family emphasizes real-time control through direct-memory-access driven peripherals, allowing sensing, computation, and actuation without CPU intervention. Key features include 1.8V to 5.5V wide operating voltage, eXtreme Low Power (XLP) sleep modes with sub-uA currents, CIP (Core Independent Peripherals) such as the CLC, Zero-Cross Detect, and an 8-bit DAC with 5-bit Filter. Hardware-based capacitive touch sensing is supported via the ADCC's CVD (Capacitive Voltage Divider) front end, eliminating software jitter and reducing CPU load. These features make the part attractive for human-interface designs where deterministic behavior and low standby power both matter. The 64 MHz internal oscillator and 16-bit PWMs enable high-resolution motor, lighting, and power-conversion control loops. The six DMA channels move ADC and communication data autonomously, freeing the CPU for higher-level supervisory tasks. Combined with the CLCs, the device allows the designer to implement custom glue logic in silicon rather than in code, reducing latency and BOM. Typical applications include LED lighting drivers, BLDC motor control, capacitive-touch HMI panels, IoT sensor nodes, and industrial automation controllers. The wide 1.8V-5.5V range also supports battery-powered portable designs including wearables and remote controls. When designing, ensure the 6x6 mm VQFN thermal pad is soldered to a sufficient copper pour for heat dissipation, and review Microchip application note TB3128 for ADCC CVD touch-sensor PCB layout. The part's high peripheral density means firmware architecture should leverage DMA and CLCs to keep the 8-bit CPU from becoming a bottleneck. This page consolidates distributor pricing, drop-in compatible alternatives, and engineering design notes that complement the manufacturer datasheet and speed up the part-selection process.

询价 联系我们
PIC18F55Q43-E/PT - 8-Bit 64MHz 32KB Flash MCU | Microchip
PIC18F55Q43-E/PT

PIC18F55Q43-E/PT - 8-Bit 64MHz 32KB Flash MCU | Microchip

The Microchip PIC18F55Q43-E/PT is an 8-bit PIC18 microcontroller from the PIC18-Q43 family, running at up to 64 MHz with 32 KB of Flash program memory, 2 KB of RAM, and packaged in a 48-pin TQFP (7x7 mm). It integrates Core Independent Peripherals including six DMA controllers, three 16-bit dual PWMs (six PWM outputs), a 12-bit Analog-to-Digital Converter with Computation (ADCC), an 8-bit DAC, and configurable logic cells (CLCs) for hardware-level customization. What is a PIC18 microcontroller? The PIC18 family is Microchip's enhanced 8-bit RISC architecture, sitting between the baseline PIC10/12/16 and the 16-bit dsPIC/PIC24 families. An 8-bit MCU executes one byte per instruction cycle, which is sufficient for cost-sensitive real-time control, sensor interfacing, and user-interface applications where deterministic timing and low power matter more than raw computational throughput. Key features include hardware-automated capacitive touch sensing via CVD techniques built into the ADCC, vectored interrupts with selectable high/low priority and three-cycle fixed latency, and XLP (eXtreme Low Power) technology for battery-friendly designs. The 12-bit ADCC with computation offloads averaging, filtering, oversampling, and threshold detection from the CPU, freeing cycles for application logic. Six DMA channels move data between peripherals and memory without CPU intervention, enabling deterministic response in motor control and power conversion. Typical applications include industrial sensor conditioning, IoT end nodes with capacitive touch interfaces, motor and fan control loops using the 16-bit PWMs, and low-cost user-interface panels. The extended (-40C to +125C) operating temperature and 64 MHz core make it appropriate for both commercial and industrial environments where reliability under thermal stress is required. When designing with this MCU, leave the NRST/MCLR pin accessible for in-circuit debugging and ensure the ADCC reference voltage is properly bypassed. Use the CLCs to implement glue logic in hardware and reduce code overhead, especially when replacing discrete logic or small state machines. This page synthesizes verified distributor pricing, drop-in PIC18 alternatives, and practical design notes beyond the manufacturer datasheet summary, structured for engineers evaluating this part for new designs and as a replacement candidate for legacy PIC18F45K22/PIC18F46K22 sockets.

询价 联系我们
PIC18F55Q43-I/6LX - 64MHz 8-bit MCU 32KB Flash 48-VQFN | Microchip
PIC18F55Q43-I/6LX

PIC18F55Q43-I/6LX - 64MHz 8-bit MCU 32KB Flash 48-VQFN | Microchip

The Microchip Technology PIC18F55Q43-I/6LX is a 64 MHz 8-bit PIC microcontroller in the PIC18-Q43 family, offering 32 KB Flash, 2 KB RAM, and 48-pin VQFN (6x6 mm) packaging for space-constrained designs. It integrates a 12-bit Analog-to-Digital Converter with Computation (ADCC), three 16-bit PWMs, a 6-channel DMA, configurable logic cells (CLCs), and on-chip 8-bit DAC with comparator for advanced signal conditioning. A microcontroller (MCU) is a single-chip computer containing a CPU, memory (Flash/RAM), and programmable peripherals. Within the broader taxonomy, this PIC18 part sits in the 8-bit MCU category -> microcontroller -> embedded processor -> semiconductor. The Q43 family emphasizes Core Independent Peripherals (CIPs) that execute hardware functions without CPU intervention, freeing the core for higher-level tasks and reducing firmware complexity for real-time control. Key features include 64 MHz operation, 32 KB self-programmable Flash, 2 KB SRAM, 256 bytes EEPROM, 36 I/O pins, and a 12-bit ADCC with up to 140 ksps conversion rate. The device also offers XLP (eXtreme Low Power) technology with sub-uA sleep currents suitable for battery-powered applications. The architecture combines an enhanced mid-range 8-bit CPU with a 32-level hardware stack, deterministic interrupt latency, and direct memory access that offloads data movement from the core. CIPs like the CLC, PWM, and ADCC enable autonomous sensor interfacing and motor control loops, which traditionally required external logic or heavy CPU code. Typical applications include capacitive touch sensing, LED lighting control, sensor signal conditioning, low-power IoT endpoints, and real-time motor drives. The wide operating voltage (1.8 V to 5.5 V) and small VQFN package suit compact, battery-powered or backplane-mounted designs. When designing with this part, allocate sufficient PCB copper under the exposed pad for thermal dissipation and verify VQFN-48 reflow profile. Consider using MPLAB X IDE with MCC (MPLAB Code Configurator) to graphically configure CIPs and accelerate firmware bring-up. This page combines distributor pricing, drop-in alternatives, and practical design guidance that supplements the Microchip datasheet (DS40002170E) with engineer-facing analysis.

询价 联系我们
PIC18F56K42-E/MV - 64KB Flash 8-Bit MCU 48-UQFN | Microchip
PIC18F56K42-E/MV

PIC18F56K42-E/MV - 64KB Flash 8-Bit MCU 48-UQFN | Microchip

The Microchip Technology PIC18F56K42-E/MV is an 8-bit PIC microcontroller from the PIC18FxxK42 family, featuring 64KB of Flash program memory, 4KB of SRAM, and 256 bytes of EEPROM, all housed in a 48-pin UQFN (6x6 mm) package. It runs at a maximum clock of 64 MHz and integrates an extensive set of Core Independent Peripherals (CIPs) including a 12-bit ADC with Computation (ADC2), 8-bit DAC, multiple comparators, PWM modules, and Direct Memory Access (DMA) controllers. The device operates across a wide voltage range and supports the eXtreme Low Power (XLP) feature set for battery-friendly designs. What is a PIC18 microcontroller? PIC18 microcontrollers are 8-bit reduced instruction set (RISC) microcontrollers from Microchip Technology built on an enhanced Harvard architecture with 16-bit instructions and an 8-bit data path. They sit at the upper tier of the 8-bit PIC family, offering higher performance (up to 16 MIPS at 64 MHz), larger memory, and more peripherals than the baseline PIC10/12/16 families. They belong to the broader category of microcontrollers (MCU), which are single-chip computers containing CPU, memory, and I/O. PIC18 MCUs are widely used in industrial control, automotive body electronics, consumer appliances, and IoT edge nodes where deterministic 8-bit performance is preferred over 32-bit complexity. Key features include: 64KB self-programmable Flash, 4KB SRAM, 256B EEPROM, 12-bit ADC2 with automated averaging and threshold comparison, up to 36 I/O pins, multiple UART/SPI/I2C interfaces, 8-bit DAC, complementary output generators, and zero-cross detection. The CIPs allow many functions to run without CPU intervention, freeing the core for application logic and reducing firmware complexity. From a technical depth perspective, the PIC18F56K42 builds on a modified Harvard architecture with a 16-bit wide instruction word and an 8-bit data bus. It includes a configurable instruction cache, hardware multiplier, and an interrupt controller with vectored interrupts and a Peripheral Interrupt Controller with DMA. The 12-bit ADC2 supports automatic threshold compare, oversampling, and accumulation, while the DMA engine can move data between peripherals and memory without waking the CPU, supporting XLP sleep currents down to nanoampere levels. Typical applications include industrial sensor nodes, automotive body and climate control modules, low-power IoT edge devices, battery-powered instrumentation, and consumer white goods. The combination of low-power XLP modes and rich peripherals makes it ideal for always-on sensor hubs that must periodically wake, capture data, and return to deep sleep. When designing with this part, ensure the UQFN-48 (MV) PCB land pattern matches Microchip's recommended footprint and that exposed pad soldering follows the IPC-7351 thermal land guidelines. Choose the industrial -40C to +125C temperature grade for harsh environments, or the extended -40C to +85C variant for commercial/industrial consumer use. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the standalone Microchip product page, with cross-references to compatible PIC18FxxK42 family members already documented on XAIPART.

询价 联系我们
PIC18F56K42-E/PT - 8-Bit 64MHz 64KB Flash MCU | Microchip
PIC18F56K42-E/PT

PIC18F56K42-E/PT - 8-Bit 64MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18F56K42-E/PT is an 8-bit PIC microcontroller from the PIC18(L)FxxK42 family, featuring a 64 MHz CPU, 64 KB Flash program memory, 4 KB SRAM, and 1 KB EEPROM, housed in a 48-pin TQFP-EP (7x7 mm) package with exposed thermal pad. It operates from 2.3V to 5.5V across the -40C to +125C extended industrial temperature range, making it suitable for both consumer and harsh-environment embedded applications. An 8-bit PIC microcontroller is a Harvard-architecture CMOS MCU that executes a RISC-like instruction set on 8-bit data while allowing 16-bit-wide program memory fetches, providing predictable timing and deterministic interrupt response. The PIC18 family sits at the top of Microchip's 8-bit portfolio as a high-performance tier, positioned above PIC16 and PIC10/12/14/15 families and below the dsPIC and PIC32 32-bit lines. The K42 sub-family adds Core Independent Peripherals (CIPs) such as CLC, NCO, PWM, and ADC with Computation (ADC2) that operate without CPU intervention, enabling low-power and real-time control designs. Key features of the PIC18F56K42 include 12-bit ADC with up to 35 external channels, 5-bit DAC, 8-bit DAC reference, hardware CVD for capacitive touch, four 16-bit timers, two I2C, two SPI, two UART, and 44 dedicated I/O pins. The integrated charge pump improves ADC accuracy at low VDD, while the XLP (eXtreme Low Power) technology enables deep Sleep currents down to sub-microamp levels with retention. Architecturally, the device combines a 16-bit program bus, 8-bit data bus, single-cycle hardware multiplier, and a vectored interrupt controller. CIPs such as CLC, NCO, and PWM with complementary outputs are interconnected via a fabric-like routing matrix, allowing analog and timing functions to be wired together in hardware and reducing firmware load. Typical applications include industrial control panels, home appliances, motor control BLDC drivers, capacitive touch user interfaces, IoT sensor nodes, and automotive body and convenience modules. The extended temperature grade (-E) supports under-hood and outdoor deployments. Designers should pay attention to VDD/VSS decoupling: place a 100 nF X7R ceramic as close as possible to each power pin pair and a bulk 10 uF tantalum or ceramic on the main rail. The exposed pad on TQFP-EP must be soldered to the ground plane for thermal dissipation and electrical reference. This page synthesizes distributor pricing, drop-in PIC18FxxK42 alternatives, and practical design notes not found in the manufacturer datasheet alone, helping procurement and firmware engineers make informed selection decisions.

询价 联系我们
PIC18F56K42-I/MV - 64KB Flash 8-bit MCU 48-UQFN | Microchip
PIC18F56K42-I/MV

PIC18F56K42-I/MV - 64KB Flash 8-bit MCU 48-UQFN | Microchip

The Microchip Technology PIC18F56K42-I/MV is an 8-bit PIC18 XLP microcontroller running at 64 MHz, integrating 64 KB of Flash, 4 KB of RAM, and 256 B of EEPROM in a 48-pin UQFN (MV) 6x6 mm package. It belongs to the PIC18(L)FxxK42 family of highly integrated, low-power, high-performance MCUs designed for embedded designs that need both advanced analog and core-independent peripherals. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), and a range of peripheral interfaces. The PIC18 architecture is an 8-bit Harvard RISC core from Microchip with an enhanced instruction set, a hardware multiplier, and prioritized vector interrupts. In the broader taxonomy, an MCU is a type of microcontroller, which itself falls under microcontrollers and processors in the embedded semiconductor category. The 56K42 specifically belongs to the PIC18(L)FxxK42 subfamily, which sits above general PIC16 parts in complexity and below the 16-bit dsPIC/PIC24 and 32-bit PIC32 families. Key features of the PIC18F56K42 include the 12-bit Analog-to-Digital Converter with Computation (ADC2) - offering up to 35 external channels with automated oversampling, averaging, filtering, and threshold comparison. The integrated Hardware Capacitive Voltage Divider (CVD) supports mTouch capacitive touch sensing without external components. The device also includes Direct Memory Access (DMA) controllers, vector interrupts, a Digital-to-Analog Converter (DAC), comparators, configurable PWMs (CCP/ECCP), and the Device Information Area (DIA) for unique serial numbers and calibration constants. The PIC18F56K42 implements Microchip's eXtreme Low Power (XLP) technology with multiple low-power modes (Sleep, Idle, Doze), a peripheral module disable feature, and an integrated charge pump that allows the 12-bit ADC to operate down to 1.8V VDD. The 48-pin UQFN package exposes up to 41 I/O pins with interrupt-on-change support and high-current sink/source capability on selected pins. The 64 MHz FOSC (16 MIPS at 4 clocks per instruction) gives ample headroom for sensor fusion, motor control loops, and protocol stacks. Typical applications include industrial control, IoT sensor nodes, home automation, capacitive touch user interfaces, low-power battery-powered instrumentation, and small motor or lighting control. The combination of large memory, advanced analog, and XLP technology makes it well suited to applications that demand both signal conditioning and ultra-low standby current. When designing with this device, use the MPLAB X IDE and MPLAB Code Configurator (MCC) to generate peripheral drivers and pin configurations. Always review the device errata for the specific silicon revision used in production, and consider migrating to the -E/-F temperature grades or QFP packages (such as PIC18F56K42-I/PT) if thermal dissipation or hand-rework is required. This page synthesizes distributor pricing, drop-in alternatives drawn from the PIC18(L)FxxK42 family, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC18F56K42T-I/MV - 8-Bit 64MHz 64KB Flash XLP MCU | Microchip
PIC18F56K42T-I/MV

PIC18F56K42T-I/MV - 8-Bit 64MHz 64KB Flash XLP MCU | Microchip

The Microchip Technology PIC18F56K42T-I/MV is a PIC18F "K42" family 8-bit microcontroller built on an enhanced Harvard RISC architecture, delivering 64 MHz (16 MIPS) CPU performance from 64 KB of on-chip Flash, 4 KB of SRAM and 256 B of EEPROM. The T-suffix indicates tape-and-reel packaging and the I-suffix denotes an industrial -40C to +85C operating range, while MV identifies the lead-free 48-pin UQFN 6x6 mm exposed-pad package. The device targets ultra-low-power XLP applications with nanoWatt XLP technology, integrated core-independent peripherals (CIPs) and intelligent analog blocks. An 8-bit PIC microcontroller (MCU) is a single-chip computer based on Microchip's proprietary Harvard architecture that separates program and data memory for deterministic instruction execution, with the K42 family positioned in the ultra-low-power XLP segment between the smaller K20 and K40 predecessors and the newer Q-series successors. In the broader hierarchy: PIC18F -> 8-bit PIC -> PIC MCU -> microcontroller -> embedded system -> semiconductor IC. The K42 family spans 28/40/48-pin packages, allowing the same firmware and development tools to scale from compact sensor nodes to feature-rich control boards. Differentiating features of the PIC18F56K42 include a 12-bit ADC2 (Analog-to-Digital Converter with Computation) with up to 35 external channels and an integrated charge pump, a hardware Capacitive Voltage Divider (CVD) for mTouch touch sensing, four 16-bit timers with built-in PWM, two USART, two SPI, two I2C and up to 36 interrupt sources. The device also integrates a 32-level hardware CRC, a Direct Memory Access (DMA) controller with 4 channels, a Windowed Watchdog Timer (WWDT) and a Vectored Interrupt module with a hardware Interrupt-on-Change (IOC) for low-latency GPIO response. The architecture combines a modified 8-bit data path with a 16-bit instruction word, providing C-compiler-friendly orthogonal addressing while retaining deterministic real-time behavior. The XLP nanoWatt technology achieves typical sleep currents below 50 nA with RAM retention, and a power-managed idle/doze mode that lets peripherals run while the CPU is gated. Charge-pump-assisted ADC2 operation allows analog conversion down to 1.8 V supply, simplifying battery-monitor designs and low-battery warning thresholds. Typical applications include IoT edge nodes, home-automation and smart-home hubs, low-power wireless sensor platforms (LoRa/BLE host MCUs), consumer appliances with capacitive touch HMIs, automotive body and interior modules, and industrial control boards requiring deterministic 8-bit GPIO-driven control. Designers typically select this device when they need deterministic interrupt response, mature MPLAB X IDE support, and a pin migration path within the same K42 family. When laying out the PCB, treat the central UQFN exposed pad as the primary thermal and electrical ground path - solder it directly to a continuous ground pour with thermal vias for thermal resistance below 30 C/W. Use the MPLAB Code Configurator (MCC) to generate CIP setup, and always include a 0.1 uF decoupling capacitor within 3 mm of each VDD pin pair to minimize switching noise on the analog rails. This page synthesizes the manufacturer datasheet, distributor pricing tiers, drop-in K42-family alternatives and practical design notes to give the engineer a single, citable reference that distributor product pages do not provide.

询价 联系我们
PIC18F56Q43-E/6LX - 8-bit 64MHz 64KB Flash MCU | Microchip
PIC18F56Q43-E/6LX

PIC18F56Q43-E/6LX - 8-bit 64MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18F56Q43-E/6LX is an 8-bit PIC18 microcontroller from the PIC18-Q43 family, integrating 64 KB of Flash program memory, 4 KB of SRAM and a 64 MHz internal oscillator in a 48-pin VQFN (6x6 mm) package. The -E suffix denotes the -40C to +125C extended operating temperature grade required for industrial and automotive-grade designs. An 8-bit microcontroller (MCU) is a programmable computing device built around a CPU, program memory and data memory on a single silicon die, optimized for deterministic real-time control, low power consumption, and a rich set of on-chip peripherals. The PIC18-Q43 family combines Microchip's most popular Core Independent Peripherals with new interconnection fabric so that hardware customization no longer requires complex firmware. The product type hierarchy is: MCU -> microcontroller -> 8-bit microcontroller -> PIC18 microcontroller -> PIC18-Q43 family -> power management/real-time control IC. Key features of the PIC18F56Q43 include six Direct Memory Access (DMA) controllers that move data without CPU intervention, three 16-bit dual PWMs giving six PWM outputs for motor and power conversion control, a 12-bit Analog-to-Digital Converter with Computation (ADCC) supporting Capacitive Voltage Divider (CVD) touch sensing, a vectored interrupt controller with selectable priorities and fixed three-cycle latency, and a Zero-Cross Detect (ZCD) peripheral. The device also includes five UARTs (one with LIN/DMX/DALI support), configurable logic cells (CLCs), and a 1.024/2.048/4.096 V voltage reference. Typical applications include industrial motor control, LED lighting and dimming, capacitive touch user interfaces, automotive body and sensor nodes, white-goods and small appliance control, and USB-to-UART bridge designs. The wide 1.8V to 5.5V operating range and low-power XLP technology make the part suitable for battery-backed appliances that must run from coin cells or 2xAA chemistries while still delivering 64 MIPS throughput.

询价 联系我们
PIC18F56Q43T-I/PT - 64KB Flash, 48-TQFP 8-bit MCU | Microchip
PIC18F56Q43T-I/PT

PIC18F56Q43T-I/PT - 64KB Flash, 48-TQFP 8-bit MCU | Microchip

The Microchip Technology PIC18F56Q43T-I/PT is an 8-bit PIC microcontroller in the PIC18-Q43 family, providing 64KB of Flash program memory, 4KB of RAM, and 1KB of EEPROM, housed in a 48-pin TQFP (7x7 mm) package. It operates up to 64MHz from a 1.8V to 5.5V supply, integrates Core Independent Peripherals, a 12-bit ADCC, three 16-bit PWMs, a 6-channel DMA, and an 8-bit DAC for real-time control tasks. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), volatile data memory (RAM), non-volatile storage (EEPROM), and a rich set of on-chip peripherals. The 8-bit PIC architecture from Microchip Technology is positioned in the taxonomy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The PIC18-Q43 family emphasizes Core Independent Peripherals (CIPs) that operate without CPU intervention, reducing firmware complexity and deterministic latency for real-time control loops. Key features include 64KB Flash, 4KB RAM, 1KB EEPROM, up to 64MHz operation across -40C to +85C industrial temperature range, integrated 12-bit ADC with Computation (ADCC) supporting capacitive voltage divider (CVD) touch sensing, three independent 16-bit PWM channels with complementary outputs, a 6-channel DMA engine, peripheral pin select (PPS) for flexible signal routing, and 5V tolerant I/O. The TQFP-48 package supports surface-mount assembly with industry-standard 0.5mm pitch. The PIC18F56Q43 uses an enhanced Harvard RISC architecture with a modified instruction set that allows 16-bit opcodes and a hardware multiplier. The ADCC module performs hardware-averaged oversampling and threshold comparison autonomously, while the unified PWM engine supports edge/center alignment for motor, lighting, and power-conversion control. The integrated DMA engine transfers data between peripherals and memory without CPU involvement, ideal for high-throughput sensor or communication links. Typical applications include industrial automation and motor control, IoT edge nodes, capacitive touch user interfaces, LED lighting controllers, sensor hubs, and small home appliances. The XLP (eXtreme Low Power) feature set targets battery-powered IoT deployments. When designing with this device, observe the decoupling network (100nF + 1uF at VDD/AVDD) and follow the Microchip MPLAB development flow with PICkit or ICD programmers. The wide operating voltage (1.8V to 5.5V) supports both 3.3V and 5V system rails with no level translation required for the digital I/O. This page synthesizes distributor pricing, same-package PIC18 drop-in alternatives, and practical design notes that complement the manufacturer datasheet.

询价 联系我们
PIC18F57K42-E/MV - 64MHz 8-bit MCU, 128KB Flash, 48-UQFN | Microchip
PIC18F57K42-E/MV

PIC18F57K42-E/MV - 64MHz 8-bit MCU, 128KB Flash, 48-UQFN | Microchip

The Microchip Technology PIC18F57K42-E/MV is a high-performance 8-bit PIC microcontroller from the PIC18FxxK42 family, integrating core independent peripherals, intelligent analog peripherals, and large Flash/RAM/EEPROM memories. The device operates at up to 64MHz, features 128KB (64K x 16) of Flash program memory, 8KB RAM, and 256B EEPROM in a compact 48-pin UQFN (6x6 mm) package (MV). The -E suffix denotes the extended operating temperature range of -40C to +125C, suitable for industrial and harsh-environment deployments. An 8-bit microcontroller (MCU) is a programmable embedded processor that integrates a CPU, memory, and peripherals onto a single silicon die. The PIC18 family sits at the top of Microchip's 8-bit portfolio, sitting between baseline PIC10/12/16 parts and higher-end dsPIC/32-bit families. The PIC18FxxK42 series specifically targets low-power (XLP) applications with rich analog integration including 12-bit ADC2 with computation, DAC, comparators, and op amps, alongside DMA, vector interrupts, and configurable logic cells (CLC). Key features of the PIC18F57K42 include the 12-bit ADC2 module with automatic averaging and threshold scanning, multiple SPI/I2C/UART interfaces with LIN support, DMA controllers for offloading the CPU, and PWM/CCP modules for motor and power control. The device includes 44 user I/O pins with peripheral pin select (PPS) for flexible signal routing. Core independent peripherals allow sensor interfacing and signal generation without CPU intervention, lowering active time and overall power consumption. The XLP (eXtreme Low Power) technology brings deep sleep currents under 50nA with retention RAM. From an architectural standpoint, the PIC18F57K42 uses a 16-bit modified Harvard architecture with separate program and data buses, executing most instructions in a single cycle. The 128KB Flash supports self-programmability via ICSP, and 256B of EEPROM provides non-volatile data storage. The 8KB SRAM includes 1KB of retention RAM that survives sleep modes for state preservation. Typical applications include industrial sensor nodes, motor control drives, IoT edge devices, building automation, HVAC control, low-power wireless sensor hubs, and consumer appliances. The combination of USB-less 48-pin density, 64MHz performance, and large memory makes it ideal for protocol-rich appliances and IoT gateways. Designers favor it for code-density, deterministic interrupt latency, and Microchip's mature MPLAB X toolchain with XC8 compiler support. When designing with the PIC18F57K42-E/MV, ensure the UQFN-48 PCB footprint includes thermal pad soldering per IPC-7351 for heat dissipation, and follow Microchip's AN2644 application note for optimal XLP sleep-mode configuration. The 48-UQFN MV package has tight pad pitch - 0.4mm spacing - so stencil design and reflow profile must be controlled during assembly. This page consolidates distributor pricing, drop-in alternatives within the PIC18FxxK42 family and cross-brand 8-bit MCU options, and practical design notes that go beyond the manufacturer datasheet to support component selection, sourcing, and PCB layout decisions.

询价 联系我们
PIC18F57K42-I/PT - 128KB Flash, 64MHz 8-bit MCU | Microchip
PIC18F57K42-I/PT

PIC18F57K42-I/PT - 128KB Flash, 64MHz 8-bit MCU | Microchip

The Microchip PIC18F57K42-I/PT is a high-performance 8-bit PIC microcontroller from the PIC18FxxK42 family, integrating 128KB of Flash program memory, 8KB of SRAM, and 256B of EEPROM in a 48-pin TQFP-EP package (7x7 mm) with an exposed thermal pad. It executes instructions at up to 64 MHz, delivering 16 MIPS of throughput, and integrates Core Independent Peripherals (CIPs) such as CWG, NCO, DSM, and Configurable Logic Cells that offload tasks from the CPU. A microcontroller (MCU) is a single-chip computer that combines a CPU, non-volatile program memory, volatile data memory, and on-chip peripherals such as timers, communication interfaces, and analog converters. PIC18F-family devices sit at the high-performance tier of Microchip's 8-bit portfolio, between baseline PIC10/PIC12/PIC16 mid-range parts and the 16-bit PIC24/dsPIC families - well suited for applications that need more code space and richer peripherals than a PIC16 can provide, but where a 32-bit Cortex-M0/M0+ would add cost and complexity. Key features of this variant include a 12-bit ADC2 (with computation), a 5-bit DAC, two comparators with 8-bit reference, multiple hardware PWM channels, DMA between memory and peripherals, vector interrupts for fast response, a Math Accelerator (MAP) for hardware multiply/divide, and a Device Information Area (DIA) for unique ID and calibration constants. The wide 2.3V to 5.5V VDD range and XLP (eXtreme Low-Power) technology allow deep sleep currents down to 50 nA with fast wake-up, targeting battery- and energy-harvesting designs. Internally, the device uses a 16-bit modified-Harvard architecture with a 32-level hardware stack, hardware multiply/divide, indirect/post-increment addressing modes, and a 64 MHz internal oscillator selectable by software. The DMA controller can move data between peripherals and RAM without CPU intervention, while Vector Interrupts reduce latency by jumping directly to the handler. These architectural choices allow developers to consolidate what would normally be done in external logic or software loops into the chip itself. Typical use cases include industrial control panels, IoT sensor nodes with low-power duty-cycled radios, motor control with field-oriented control (FOC) for BLDC, USB human-interface devices (HID/CDC), and white-goods or HVAC controllers. The 48-pin TQFP footprint also suits quick migration from PIC18F47K42 designs that require the larger 128KB memory tier without changing PCB layout. The TQFP-EP package provides a thermal pad that improves heat spreading for full-speed operation across the industrial -40C to +85C range. When designing with this MCU, allow the exposed thermal pad (pin 49) to be soldered to a copper pour of at least 1 square inch on both top and bottom layers to meet the 64 MHz operating point reliably. Use MPLAB X IDE with the XC8 compiler to take advantage of DIA and the hardware Math Accelerator. This page consolidates distributor pricing, drop-in alternatives, and practical design notes that complement the manufacturer datasheet for engineers evaluating the PIC18F57K42-I/PT for new designs and field replacements.

询价 联系我们