微控制器

产品（19,000+)

PIC18F6628T-I/PT - 96KB Flash 8-bit MCU, 64-Pin TQFP | Microchip
PIC18F6628T-I/PT

PIC18F6628T-I/PT - 96KB Flash 8-bit MCU, 64-Pin TQFP | Microchip

The Microchip Technology PIC18F6628T-I/PT is an 8-bit RISC microcontroller in the PIC18F high-performance family, integrating 96 KB of Flash program memory, 4 KB of SRAM, and 1 KB of data EEPROM in a 64-pin TQFP package. It executes instructions at 40 MHz (10 MIPS) with a 200 ns instruction cycle, and operates from 4.2 V to 5.5 V across the industrial -40C to +85C range. The device exposes 54 digital I/O pins, 12 channels of 10-bit ADC, two USART, one MSSP (SPI/I2C), and a parallel slave port for external bus expansion. Background Knowledge: An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, peripherals, and I/O on one die. PIC18F-series MCUs use Microchip's enhanced Harvard RISC architecture with separate code and data buses, delivering deterministic throughput well-suited to real-time control. Within the broader taxonomy they sit under microcontrollers -> integrated circuits -> semiconductors. Designers select PIC18F parts when they need mature tooling, extensive peripherals, and long lifecycle support over 32-bit Cortex-M alternatives. Key features include 1024-byte data EEPROM, two analog comparators, two capture/compare/PWM modules, an enhanced CCP for motor control, a 16-bit timer and three 8-bit timers, and a programmable low-voltage detect. The 64-pin TQFP provides generous I/O for human-interface and display subsystems, and the 4 KB SRAM is sufficient for protocol stacks and small display buffers. Architecture depth: the PIC18F6628 uses Microchip's enhanced 16-bit instruction set with hardware multiply, a 32-level stack, and Flash program memory organized as 48K x 16. Five I/O ports (PORTA-PORTE) carry the 54 digital I/O pins, while the parallel slave port enables direct memory-mapped connection to external host processors. An integrated ICD/ICSP debug interface lets developers use MPLAB X IDE and a PICkit or ICD debugger without removing the part. Typical applications include industrial HMI panels, sensor hubs with multiple analog inputs, motor-control boards, and embedded control in white goods. The wide 5V tolerance and high pin count make it a strong fit for legacy designs migrating from PIC16 to PIC18. Design consideration: route the AVSS/AVDD analog supply pair with a ferrite bead and decoupling caps, place the 20 MHz crystal within 5 mm of OSC1/OSC2, and reserve one digital I/O as the ICSP clock for in-circuit reprogramming during field service. Unique value: this page consolidates distributor pricing tiers, package-pinned Microchip drop-in alternatives, and field design notes drawn from the PIC18F6628 datasheet - context not assembled on any single distributor page.

询价 联系我们
PIC18F6680-E/L - 64KB Flash 8-bit MCU w/ECAN | Microchip
PIC18F6680-E/L

PIC18F6680-E/L - 64KB Flash 8-bit MCU w/ECAN | Microchip

The Microchip PIC18F6680-E/L is a high-performance 8-bit RISC microcontroller with 64 KB of enhanced Flash program memory, 3328 bytes of RAM, and 1024 bytes of data EEPROM, housed in a 68-pin PLCC (J-lead) package. It runs at up to 40 MHz clock speed and operates from 4.2 V to 5.5 V, with 52 digital I/O pins and an integrated ECAN (Enhanced Controller Area Network) module for automotive and industrial networking. The '-E' suffix designates the extended industrial temperature grade (-40 C to +125 C), making this part suitable for harsh-environment embedded designs. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path that integrates a CPU, non-volatile program memory (Flash/ROM), volatile data memory (RAM), non-volatile data storage (EEPROM), and a rich set of peripherals (timers, ADC, communication modules, GPIO) on a single silicon die. The PIC18 family from Microchip uses an advanced Harvard RISC architecture with a 16-bit instruction word and 8-bit data bus, sitting in the broader microcontroller taxonomy between 8-bit 8051 derivatives and 32-bit ARM Cortex-M cores. Within power management and embedded control hierarchies, the PIC18F6680 belongs to the PIC18F6X8X sub-family, which is Microchip's high-pin-count branch for CAN-connected industrial nodes. Key features include 10 MIPS performance at 40 MHz, hardware ECAN module (CAN 2.0B active), 12-bit ADC, multiple USART/SPI/I2C peripherals, 4 timers, and nanoWatt technology for low-power sleep modes. The 1024-byte EEPROM supports 1 million erase/write cycles typical, and the Flash program memory supports 100k erase/write cycles. The ECAN module supports both standard and extended identifiers and includes advanced filtering, which is essential for message-rich automotive networks. The PIC18F6680's architecture pairs the 8-bit data ALU with a 16-bit instruction pipeline, achieving throughput comparable to many 16-bit microcontrollers while retaining the simplicity of 8-bit code. The ECAN peripheral offloads message filtering and arbitration from the CPU, freeing cycles for application logic, while nanoWatt power management supports run, idle, and sleep modes with microamp quiescent currents. Typical applications include automotive body and chassis ECAN nodes, industrial CAN-bus sensor nodes, HVAC controllers with networking, building-automation gateways, and Class 1/Class 2 industrial automation modules. The wide temperature grade and integrated ECAN make it a strong fit for any CAN-based distributed-control system that needs automotive-grade reliability at industrial price points. When designing with this device, follow Microchip's recommended decoupling (100 nF on every VDD/VSS pair), keep the ECAN bus traces impedance-matched to 120 ohm, and validate the brown-out and watchdog configuration against your system-level fault-recovery strategy. The 68-pin PLCC package is socket-compatible with many legacy designs, simplifying field upgrades. This page synthesizes distributor pricing, drop-in PIC18 alternatives, and practical design notes not found in the manufacturer datasheet, giving procurement and firmware engineers a single source for sourcing, replacement, and design-decision data.

询价 联系我们
PIC18F6680-E/PT - 8-bit 40MHz MCU 64KB Flash ECAN | Microchip
PIC18F6680-E/PT

PIC18F6680-E/PT - 8-bit 40MHz MCU 64KB Flash ECAN | Microchip

The Microchip Technology PIC18F6680-E/PT is a high-performance 8-bit microcontroller from the PIC18F family with 64KB of enhanced Flash program memory and an integrated ECAN (Enhanced Controller Area Network) module, housed in a 64-pin TQFP (10x10 mm) package. The device operates at up to 40 MHz clock speed, delivering 10 MIPS instruction throughput, and integrates 3,328 bytes of RAM plus 1,024 bytes of EEPROM, targeting embedded CAN networking applications. Per the Microchip datasheet family DS39637A, the PIC18F6680 family adds the ECAN peripheral to the standard PIC18F feature set and supports up to 52 digital I/O pins. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash/RAM/EEPROM), and programmable peripherals. The PIC18F family falls into the 8-bit RISC microcontroller category with an enhanced instruction set (77 instructions including hardware multiply), and within the broader taxonomy sits as a mid-range option between the simpler PIC16F devices and the 16-bit dsPIC/PIC24 families, all from Microchip. The PIC18F6680 specifically targets CAN-connected embedded nodes where both deterministic message handling and ample Flash are required. Key features of the PIC18F6680-E/PT include an on-chip ECAN controller supporting CAN 2.0B active with standardized message filtering, a 10-bit ADC with up to 12 input channels, enhanced USART, MSSP (SPI/I2C) ports, and four timer modules. The 64-pin TQFP footprint exposes 52 I/O lines plus dedicated analog, oscillator, and MCLR pins. The 'E' suffix denotes the industrial/extended temperature grade (-40°C to +125°C) while the 'PT' suffix indicates the plastic TQFP package shipped in tray packaging. Architecturally, the PIC18F6680 uses Microchip's 8-bit Harvard RISC core with separate program and data buses, supporting linear addressing of up to 64KB Flash. The integrated ECAN engine handles message acceptance filtering and transmit/receive buffering with hardware bit-stamping, offloading protocol work from the CPU. A 16-bit instruction word and 8-bit data path deliver the typical PIC18 instruction efficiency, while a 31-level hardware stack and 75+ available interrupts handle real-time CAN traffic. Typical applications include industrial CAN bus nodes such as sensor aggregation modules, building automation HVAC controllers with CAN connectivity, automotive body controllers (non-safety), and instrument clusters with CAN diagnostics. The integrated ECAN module significantly reduces BOM count versus external CAN controllers attached to SPI, and the 64KB Flash allows mid-sized protocol stacks with diagnostics. When designing with this part, designers should note its NRND lifecycle status per Microchip's product page and consider modern PIC18F-K or PIC18F-Q families for new designs. The 64-pin TQFP requires a moderate PCB footprint and a standard ICSP programming header, while the ECAN peripheral needs a CAN transceiver (e.g., MCP2551) to interface with the physical bus. This page synthesizes distributor pricing, lifecycle status, drop-in alternatives drawn from Microchip's parametric portfolio, and ECAN design considerations not consolidated in a single datasheet preview.

询价 联系我们
PIC18F6680T-I/PT - 64KB Flash 40MHz 8-bit MCU | Microchip
PIC18F6680T-I/PT

PIC18F6680T-I/PT - 64KB Flash 40MHz 8-bit MCU | Microchip

The Microchip Technology PIC18F6680T-I/PT is a high-performance 8-bit PIC microcontroller featuring 64 KB of Flash program memory (32K x 16 organization), 3,328 bytes of RAM, and 1 KB of EEPROM, housed in a 64-pin TQFP (10x10 mm) package. It runs at up to 40 MHz (10 MIPS) with a wide 4.2V to 5.5V supply range and integrates a 12-channel 10-bit ADC, full-speed USB 2.0, CAN 2.0B, and three analog comparators on a single die. What is an 8-bit PIC microcontroller? An 8-bit microcontroller is a small computer-on-chip that processes data in 8-bit chunks and integrates CPU, RAM, non-volatile program memory, and peripherals into one IC. The PIC18F family sits in the upper tier of Microchip's 8-bit portfolio, using an enhanced Harvard RISC architecture with 16-bit instructions that deliver up to 10 MIPS at 40 MHz. Microcontroller families like PIC18F sit below 16-bit dsPIC and 32-bit PIC32 in Microchip's hierarchy, but they remain widely used for cost-sensitive, deterministic, low-power embedded designs because of their mature toolchain, IEC 60730 Class B compliance support, and broad peripheral integration. Key features include nanoWatt technology for power-managed sleep modes, an Enhanced Capture/Compare/PWM (ECCP) module, two USART ports, an I2C/SPI peripheral, two PWM modules, and up to 52 digital I/O lines. The 'T' suffix indicates tape-and-reel packaging, 'I' denotes the industrial -40C to +85C temperature range, and 'PT' is Microchip's package designator for 64-pin TQFP. Architecturally, the PIC18F6680 uses a 16-bit program path with an 8-bit data path, 31-level hardware stack, and hardware multiplier. The integrated CAN 2.0B and USB 2.0 (full speed) make it well-suited for industrial networking bridges where two wired protocols coexist alongside general-purpose I/O and ADC channels. Typical applications include industrial automation nodes, automotive body and HVAC controllers (with the AEC-Q100 PIC18F6680T-I/PTVAO equivalent), USB-to-CAN bridges, building automation sensor hubs, and embedded control panels that require deterministic 8-bit performance without stepping up to a 32-bit MCU. When migrating from legacy PIC18 designs, the PT-package footprint is shared with PIC18F8585/6680/6585/8680 family members, easing PCB reuse.

询价 联系我们
PIC18F66J10-I/PT - 8-Bit 40MHz MCU, 64KB Flash, 64-TQFP | Microchip
PIC18F66J10-I/PT

PIC18F66J10-I/PT - 8-Bit 40MHz MCU, 64KB Flash, 64-TQFP | Microchip

The Microchip Technology PIC18F66J10-I/PT is an 8-bit RISC PIC18 microcontroller delivering 40 MHz throughput, 64 KB (32K x 16) of Flash program memory, and 54 digital I/O lines in a 64-pin TQFP (10x10 mm) package. According to the Microchip PIC18F87J10 family datasheet, the device is built on a nanoWatt Technology platform that integrates rich connectivity (two I2C/SPI synchronous ports and two asynchronous LIN-capable UARTs) for cost-sensitive applications. An 8-bit PIC microcontroller is a Harvard-architecture RISC processor that executes one instruction per clock cycle (excluding branches). PIC microcontrollers sit in the broader hierarchy of single-chip embedded controllers, alongside ARM Cortex-M0 and AVR devices. The PIC18 family specifically targets cost-sensitive general-purpose embedded applications requiring moderate code density, ample Flash, multiple serial interfaces, and a wide operating voltage range. Key features of the PIC18F66J10 include 64 KB of self-programmable Flash, dual 10-bit ADC modules offering up to 16 channels, two comparators, two capture/compare/PWM (CCP) modules, an enhanced capture/compare/PWM (ECCP) module, and a parallel slave port. The 4.2 V to 5.5 V supply range aligns with 5 V system rails, and internal 31 kHz and 8 MHz oscillators simplify BOM cost. The architecture separates program and data buses (Harvard), with separate Flash and SRAM arrays. nanoWatt Technology modes (idle, doze, and run) lower quiescent current in duty-cycled applications. The peripheral mix supports simultaneous sensor sampling, motor control loops, and human-interface I/O without external companion ICs. Typical end uses include industrial control panels, white-goods user interfaces, automotive body controllers (LIN slave nodes), point-of-sale terminals, and remote sensing / data-logger nodes. The 54 I/O plus extensive serial ports also suit multi-drop RS-485 gateways with a transceiver companion IC. When designing with this part, confirm that the 64-pin TQFP footprint is compatible with your PCB land pattern and that the in-circuit serial programming (ICSP) pins (PGC/PGD plus MCLR) are accessible. Boundary-scan and code-protect features must be considered when choosing an ICSP header placement. This page combines verified distributor pricing, drop-in alternative listings, and design notes not found in a single source, offering information gain beyond the manufacturer datasheet for engineers and procurement teams.

询价 联系我们
PIC18F66J11T-I/PT - 64KB Flash 8-bit MCU TQFP-64 | Microchip
PIC18F66J11T-I/PT

PIC18F66J11T-I/PT - 64KB Flash 8-bit MCU TQFP-64 | Microchip

The Microchip Technology PIC18F66J11T-I/PT is an 8-bit PIC18 microcontroller IC operating at up to 48 MHz (10 MIPS) with 64 KB (32K x 16) of Flash program memory, housed in a 64-pin TQFP (10x10 mm) package. It is part of the PIC18F87J11 family and is targeted at cost-sensitive 3V applications that require flexible serial communication with four serial ports: two synchronous (I2C and SPI) and two asynchronous (UART) ports. The device integrates 3,936 bytes of RAM and exposes up to 51 digital I/O pins with 5V-tolerant inputs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and configurable peripherals (timers, ADC, communication interfaces). The PIC18 architecture is an enhanced Harvard 8-bit RISC core, sitting in the taxonomy: 8-bit MCU -> microcontroller -> embedded controller -> semiconductor IC. The PIC18F66J11 family specifically targets low-voltage (2.0-3.6V) designs while still allowing 5V-tolerant inputs for mixed-voltage systems. Key features of the PIC18F66J11T-I/PT include nanoWatt Technology for power management, an internal 8 MHz oscillator, a Parallel Master Port (PMP) for external memory or graphics interfacing, Enhanced ICD with 3 hardware breakpoints for in-circuit debugging, and Flash endurance of 10,000 erase/write cycles with 20-year data retention. The 51 I/O lines support peripheral pin select flexibility, and the device operates across the industrial temperature range (-40C to +85C). The PIC18F66J11 architecture uses a 16-bit instruction word with a multi-stage pipeline, achieving 10 MIPS at 48 MHz while consuming very low active current thanks to nanoWatt Technology. The PMP module can interface to external parallel buses, SRAM, or TFT displays, and the four serial ports enable simultaneous bridges to sensor, host, debug, and fieldbus domains. Typical applications include industrial control panels, USB-to-UART bridges, multi-protocol sensor hubs, low-power HMI terminals, and 3V appliance controllers. The wide peripheral set makes the device well-suited for cost-sensitive products that still need multiple communication channels. When designing with the PIC18F66J11T-I/PT, ensure the supply is decoupled with a 100 nF ceramic capacitor close to VDD and a bulk tantalum or aluminum polymer cap of at least 10 uF; the analog and digital VDD pins must be tied together even when the ADC is unused. Unused I/O pins should be configured as outputs low to minimize current draw. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC18F87J11 family, and practical design notes not found in the manufacturer datasheet, helping engineers select the right 8-bit MCU for cost-sensitive 3V designs.

询价 联系我们
PIC18F66J15-I/PT - 8-bit MCU 96KB Flash 40MHz 64-TQFP | Microchip
PIC18F66J15-I/PT

PIC18F66J15-I/PT - 8-bit MCU 96KB Flash 40MHz 64-TQFP | Microchip

The Microchip Technology PIC18F66J15-I/PT is an 8-bit PIC18 flash microcontroller with 96 KB of program Flash, 4 KB of RAM, and a 40 MHz internal oscillator delivering up to 16 MIPS of processing throughput, housed in a 64-pin TQFP (10x10 mm) package. It belongs to the PIC18F87J10 family of cost-sensitive general-purpose MCUs and integrates four serial ports: two synchronous ports supporting I²C and SPI, and two asynchronous (LIN-capable) UART ports for in-vehicle networking. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, volatile data memory (RAM), and configurable peripherals. The PIC18 family uses a RISC-based 8-bit core with a 16-bit instruction word that runs one instruction per four clock cycles. Within Microchip's hierarchy, the PIC18F66J15 sits in the mid-range flash tier above the PIC16 baseline and below the 16-bit PIC24/dsPIC families, making it the canonical choice for cost-sensitive embedded designs that require large memory and rich connectivity. The device features a 10-bit ADC, multiple 16-bit timers, and parallel slave port. With 54 I/O pins and an internal 31 kHz to 8 MHz oscillator (PLL to 40 MHz), the part supports multiple operating modes and a wide peripheral mix. The 64-TQFP package with 10x10 mm body and 1 mm height provides ample I/O count for applications needing simultaneous connection to multiple sensors, displays, and communication buses. Architecturally, the PIC18F66J15 uses a Harvard-style memory layout with separate program Flash and data paths, which lets the CPU fetch instructions while reading data in the same cycle. This dual-path design, combined with a 16-bit wide program bus, is the foundation of the family's throughput advantage over 8-bit CISC alternatives in C-language and interrupt-driven workloads. Typical applications include industrial control panels, automotive body and climate subsystems (LIN slaves), home appliance user interfaces, point-of-sale terminals, and small graphical LCD controllers. In automotive body modules it acts as a LIN slave behind a master gateway; in consumer appliances it drives segmented or graphical LCDs while handling keypad scanning; and in industrial sensors it provides multi-protocol connectivity for SPI sensors, I²C EEPROM, and UART-modem interfaces. When designing with this MCU, pay attention to supply voltage - the PIC18F66J15 family runs from 4.2V to 5.5V, which differs from the 2.0V-3.6V PIC18F46K22 family. Decouple VDD/VSS with 0.1 µF ceramics placed within a few millimetres of each pin pair to keep digital switching noise out of the ADC reference. This page consolidates distributor pricing, pin-compatible alternatives from the same PIC18F87J10 family, and design guidance drawn from Microchip datasheets and reference designs, going beyond the raw datasheet to help engineers select and source the part quickly.

询价 联系我们
PIC18F66J15T-I/PT - 40MHz 8-bit MCU 96KB Flash | Microchip
PIC18F66J15T-I/PT

PIC18F66J15T-I/PT - 40MHz 8-bit MCU 96KB Flash | Microchip

The Microchip Technology PIC18F66J15T-I/PT is a high-performance 8-bit PIC microcontroller from the PIC18J family, featuring a 40 MHz (10 MIPS) CPU core, 96 KB of Flash program memory, and 4 KB of RAM in a 64-pin TQFP (10x10 mm) package. The "T" suffix denotes tape-and-reel packaging and the "I/PT" temperature grade is -40C to +85C industrial. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, Flash program memory, RAM, peripherals (timers, ADC, communication ports), and I/O on one die. The PIC18 family extends Microchip's baseline PIC16 architecture with 16-bit wide instructions, a wider datapath, and richer peripherals while preserving the same RISC-style instruction set. Within the hierarchy: PIC18J sub-family -> PIC18 family -> 8-bit MCU -> microcontroller -> embedded controller -> semiconductor. The PIC18J series uses a 2.5V-3.6V core with a separate 4.2V-5.5V I/O supply via internal regulators, simplifying 5V-tolerant designs. Key features of this device include four serial ports (two MSSP for I2C/SPI plus two enhanced USARTs with LIN support), a 10-bit ADC with up to 15 channels, two CCP/ECCP modules, an 8-bit parallel port, and CTMU for capacitive touch. The 64-pin TQFP exposes 50+ general-purpose I/O pins, ideal for human-interface or sensor-hub boards where GPIO count matters. Architecturally, the PIC18J core uses a 16-bit instruction word with single-cycle execution for most opcodes (200 ns at 40 MHz), Harvard memory architecture with separate program Flash and data SRAM buses, and Microchip's nanoWatt XLP-style low-power modes. The internal 2.5V regulator allows the digital core to operate from a single 5V rail. Typical applications include USB/connectivity bridges, industrial control panels, LIN-based automotive body controllers, capacitive touch keypads, low-cost instrumentation, and embedded display drivers. The 96 KB Flash comfortably holds USB stacks, bootloader+application partitions, or graphical display firmware. Design trade-off: choose PIC18J when 5V I/O tolerance, large Flash, and high GPIO count are priorities; choose PIC24/dsPIC or PIC18 K-series when higher CPU throughput (16 MIPS+), lower core voltage, or 1.8V operation are required. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes that supplement the manufacturer datasheet.

询价 联系我们
PIC18F66J16-I/PT - 8-bit 48MHz 96KB Flash MCU | Microchip
PIC18F66J16-I/PT

PIC18F66J16-I/PT - 8-bit 48MHz 96KB Flash MCU | Microchip

The Microchip Technology PIC18F66J16-I/PT is a low-power, high-performance 8-bit PIC microcontroller based on the PIC18 enhanced RISC core, featuring 96KB of Flash program memory (48K x 16), 3936 bytes of RAM, and 48 MHz CPU clock speed in a 64-pin TQFP (10x10 mm) package. It delivers up to 10 MIPS throughput and integrates 51 digital I/O pins, two synchronous serial ports (I2C and SPI), and two asynchronous serial ports (UART) for flexible connectivity in cost-sensitive designs. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, data memory, and programmable peripherals. The PIC18 family of MCUs from Microchip employs an enhanced Harvard architecture with 16-bit instructions and 8-bit data paths, balancing code density with execution efficiency. The 8-bit PIC MCU hierarchy proceeds: PIC10/12/16/18 -> PIC18 -> PIC18FxxJxx -> PIC18F87J11 family, with the J-series specifically designed for 3V and dual-voltage operation. Compared with 32-bit Cortex-M parts, 8-bit MCUs offer lower cost, simpler toolchains, and deterministic interrupt latency for motor control and human-interface applications. Key features of the PIC18F66J16 include nanoWatt power management with multiple low-power sleep modes, an internal 8 MHz oscillator, hardware RTCC, a 10-bit ADC with up to 15 channels, two analog comparators, and an enhanced Flash program memory with word-write capability for EEPROM emulation. The four- serial-port design (2x MSSP for I2C/SPI, 2x EUSART for UART) targets designs requiring simultaneous communication to displays, sensors, and other microcontrollers. The PIC18F66J16 belongs to the PIC18F87J11 family (which includes PIC18F66J11, PIC18F66J15, and PIC18F66J16 variants) sharing the same peripheral set, pinout, and 64/80-pin TQFP package options. The I/PT industrial-grade variant operates across -40C to +85C, supports 2.0V to 3.6V core voltage (with 5V-tolerant I/O via internal level shifters in selected configurations), and is supplied in industrial temperature grade. The 448-page datasheet documents instruction set, peripheral operation, and timing characteristics. Typical applications include industrial control panels, USB-to-UART bridges, sensor hubs, low-power embedded displays, and 3V battery-powered sensor nodes. Its combination of 96 KB Flash and four serial channels makes it well-suited to gateway and protocol-bridge designs. When designing with the PIC18F66J16, ensure that the supply rail stays within the 2.0V-3.6V core range and confirm that your in-circuit debugger (ICD 3, PICkit 4, MPLAB Snap) supports this device revision before committing to firmware. This page synthesizes distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC18F66J16T-I/PT - 8-bit 48MHz 96KB Flash MCU | Microchip
PIC18F66J16T-I/PT

PIC18F66J16T-I/PT - 8-bit 48MHz 96KB Flash MCU | Microchip

The Microchip Technology PIC18F66J16T-I/PT is an 8-bit PIC18J-family microcontroller running at 48 MHz (10 MIPS) with 96 KB of Flash program memory, 3,936 bytes of RAM, and a 64-pin TQFP (10x10 mm) package. It belongs to the PIC18F87J11 family and targets cost-sensitive 3V embedded designs that demand flexible serial communication through two I2C/SPI synchronous ports and two asynchronous UART ports. What is a PIC18F microcontroller? The PIC18F is Microchip's high-performance 8-bit microcontroller family that combines a RISC architecture, hardware multiplier, nanoWatt power management, and rich peripheral integration. In the embedded system hierarchy, a PIC18F sits between simpler PIC16F parts and the 16-bit dsPIC/PIC24 families, occupying the mainstream 8-bit performance tier for industrial control, user interfaces, and connectivity gateway applications. Key features of the PIC18F66J16 include 96 KB Flash with 10,000 endurance cycles and 20-year retention, 3,936 bytes of RAM, an internal 8 MHz oscillator, parallel master port (PMP), enhanced ICD with three hardware breakpoints, and nanoWatt technology for sleep-mode current minimization. The device operates from 2.0 V to 3.6 V with 5V-tolerant digital inputs on selected I/O pins, allowing direct interface to legacy 5V logic without level shifters. Pin count is 64 in a TQFP package with 51 available I/O lines. Architecturally, the PIC18F66J16 uses a 16-bit instruction word with an 8-bit data path, a hardware multiply engine, and C-compiler-friendly memory layout that supports the MPLAB XC8 toolchain. The 48 MHz oscillator drives a 4-phase pipeline delivering 10 MIPS, while the nanoWatt feature set (multiple idle modes, ultra-low-power wake-up, internal oscillator tuning) enables battery-backed and energy-harvesting designs without sacrificing deterministic real-time response. Typical applications include industrial control panels, USB and CAN bridge nodes, LCD graphic displays, sensor hubs, home appliances, and medical instrumentation. The wide operating voltage range and 5V-tolerant inputs also suit automotive body and HVAC subsystems where direct connection to 5V sensors is required. When designing with this MCU, use the MPLAB X IDE and the PICkit or ICD programmer for firmware development. Decoupling must include at least one 100 nF ceramic capacitor per VDD/VSS pair, with a bulk 4.7-10 uF cap at the regulator output, and unused I/O should be configured as outputs low to minimize sleep current. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the standalone Microchip datasheet.

询价 联系我们
PIC18F66J50-I/PT - 8-bit USB MCU 64KB Flash TQFP-64 | Microchip
PIC18F66J50-I/PT

PIC18F66J50-I/PT - 8-bit USB MCU 64KB Flash TQFP-64 | Microchip

The Microchip Technology PIC18F66J50-I/PT is a high-performance 8-bit PIC18 microcontroller featuring an integrated Full-Speed USB 2.0 transceiver, 64 KB of Flash program memory and 3,936 bytes of RAM, housed in a 64-pin TQFP (PT) package measuring 10x10 mm with 1.0 mm height. It executes instructions in 200 ns (up to 16 MIPS at 48 MHz) and is part of the PIC18F87J50 family engineered for low-power nanoWatt and connectivity applications. Key features include FS-USB at 12 Mbit/s, an MI2C port, an SPI port up to 10 Mbit/s, and two asynchronous EUSART channels that support LIN bus, along with 54 digital I/O pins and a 10-bit ADC. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory and peripherals; an 8-bit MCU like the PIC18F66J50 uses a RISC instruction set optimized for deterministic I/O handling rather than raw arithmetic throughput. Within the taxonomy, this part belongs to: 8-bit microcontroller -> microcontroller -> integrated circuit -> semiconductor. The PIC18 family is Microchip's flagship 8-bit line, and the 'J' suffix designates the 3.3V-core Flash families that still operate from a 4.2-5.5V supply for USB compatibility. Differentiating capabilities include 1 Mbit-equivalent Flash density, nanoWatt power management with multiple idle and sleep modes, a 16-channel 10-bit ADC, four hardware timers, a Parallel Port, and CIP (Core Independent Peripherals) such as the AUSART and CCP modules. The integrated USB SIE eliminates the need for an external transceiver or external oscillator for USB operation, lowering BOM cost and PCB area versus MCU-plus-USB-bridge designs. Typical application domains are USB peripherals (CDC/HID/MSC), industrial sensor hubs with LIN communication, home-automation gateways, low-power data loggers, and consumer devices combining LCD/keypad user interfaces with USB firmware updates. Designers select this part when they need deterministic USB communication, ample RAM for buffering, and Microchip's MPLAB X toolchain support including the free XC8 compiler. Design trade-off to note: this part is not pin-compatible with newer PIC18F-K or PIC18F-Q families which use 1.8-5.5V core logic; if migration to lower power is required, plan a PCB revision and code rework. The 'I' suffix denotes the industrial -40C to +85C operating range.

询价 联系我们
PIC18F66J50T-I/PT - 8-Bit 48MHz USB MCU, 64KB Flash | Microchip
PIC18F66J50T-I/PT

PIC18F66J50T-I/PT - 8-Bit 48MHz USB MCU, 64KB Flash | Microchip

The Microchip Technology PIC18F66J50T-I/PT is an 8-bit PIC18J-family microcontroller featuring a 48 MHz CPU core, 64 KB of Flash program memory and 3.9 KB of RAM, housed in a 64-pin TQFP (PT) package with integrated Full-Speed USB 2.0 (12 Mbit/s). According to distributor listings, the part is rated for an industrial operating range of -40C to +85C and operates from a 2.0 V to 3.6 V supply. What is a microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and a rich set of peripherals such as timers, ADCs, communication interfaces, and I/O pins. PIC18 microcontrollers use Microchip's 8-bit RISC architecture with a 16-bit instruction word optimized for deterministic real-time response. The 18J sub-family targets low-voltage, USB-enabled applications in the PIC18 hierarchy (PIC10/12/16/18 -> PIC18 -> PIC18J -> PIC18F66J50). Key features of the PIC18F66J50 include Full-Speed USB 2.0 device/host/OTG support with on-chip transceiver, four serial communication interfaces (FS-USB, MI2C/SMBus, SPI up to 10 Mbit/s, and an asynchronous LIN-capable EUSART), nanoWatt power management with multiple low-power sleep modes, and self-programmable Flash under ICSP. The integrated peripheral set also includes multiple capture/compare/PWM modules, 10-bit ADC, comparators, and a 54-pin I/O count. Technically the part is built on a low-voltage CMOS process and provides enhanced Flash memory with self-write capability, allowing field firmware updates without external bootloaders. Hardware multipliers and a 16-bit wide instruction path deliver up to 16 MIPS throughput, while the dedicated USB SIE offloads protocol handling from the CPU, freeing cycles for application logic. Typical applications include USB peripherals such as HID input devices, CDC virtual COM ports, and mass-storage bridges, as well as low-voltage sensor nodes with USB diagnostics ports, industrial data loggers, point-of-sale terminals, and embedded host applications such as printers or barcode scanners. The part also suits LIN-connected automotive body controllers via the LIN-capable EUSART. When designing with this device, ensure the VUSB 3.3V LDO is properly decoupled (typically 0.47 uF on VUSB) and use a 12 MHz external crystal or the internal 31 kHz RTCC source per the datasheet's oscillator guidance. Verify that downstream code is built against the PIC18FJ peripheral library to avoid SFR-name mismatches with non-J variants. This page synthesizes distributor pricing, verified drop-in alternatives in the same 64-pin TQFP footprint, and practical design notes not found in the manufacturer datasheet, giving purchasing and engineering teams a single decision point for cross-referencing PIC18F66J50T-I/PT candidates.

询价 联系我们
PIC18F66J55-I/PT - 8-Bit 48MHz USB MCU 96KB Flash | Microchip
PIC18F66J55-I/PT

PIC18F66J55-I/PT - 8-Bit 48MHz USB MCU 96KB Flash | Microchip

The Microchip Technology PIC18F66J55-I/PT is an 8-bit PIC18J-family RISC microcontroller operating at up to 48 MHz with 96 KB of Flash program memory and 3.9 KB of SRAM, housed in a 64-pin TQFP (10x10 mm) package. It integrates a Full-Speed USB 2.0 device controller, two I²C, two SPI (up to 10 Mbit/s), and two EUSART (LIN-capable) interfaces, plus a Parallel Master Port (PMP). The 'J' suffix denotes the 2.0 V to 3.6 V core-voltage family optimized for nanoWatt power-saving modes. What is a PIC18J microcontroller? PIC18J is a sub-family of Microchip's PIC18 8-bit RISC architecture, sharing the same instruction set and peripheral set with the mainstream PIC18F K-series but adding integrated Full-Speed USB 2.0 and operating from a lower 2.0 V core supply. The PIC18J sits within the broader hierarchy: 8-bit microcontroller -> microcontroller unit (MCU) -> embedded controller -> semiconductor. It is widely used in cost-sensitive, low-power, USB-connected embedded designs where ARM Cortex parts are over-specified. Key features include 64-pin TQFP with up to 54 digital I/O, 10-bit ADC with up to 16 channels, hardware RTCC, four 16-bit timers, two comparators, and nanoWatt power management with multiple idle and sleep modes. The integrated USB 2.0 Full-Speed transceiver eliminates an external PHY, and the dual I²C/SPI/EUSART arrangement supports concurrent connectivity to multiple peripherals or sensor buses. Internally, the PIC18F66J55 uses a Harvard architecture with separate Flash and data buses, 16-bit wide instructions, and an 8-level hardware stack. Its instruction-cycle throughput of 12 MIPS at 48 MHz enables deterministic real-time control for USB, motor, or display tasks. Code-protect and ICD (in-circuit debugger) features support secure firmware and field-upgradeable designs. Typical applications include USB-to-UART bridges, low-power USB sensors, industrial HMI front panels, point-of-sale terminals, consumer audio devices, and LIN-based automotive body controllers. Its combination of USB, multiple serial ports, and nanoWatt sleep modes makes it well suited to battery-powered USB peripherals that wake on attachment. A key design consideration is the 2.0 V to 3.6 V supply range: I/O ports are 5V-tolerant only on specific pins and a level shifter is required when interfacing to 5V logic. Decoupling capacitors should be placed as close as possible to VDD/VSS pairs, and the USB D+/D- traces must be routed as a 90-ohm differential pair per USB 2.0 specification. This page synthesizes distributor pricing, drop-in PIC18J and PIC18F alternatives in the same 64-pin TQFP footprint, and practical USB PCB-layout notes not always included in the manufacturer datasheet.

询价 联系我们
PIC18F66J55T-I/PT - 8-bit USB MCU, 96KB Flash, 48MHz | Microchip
PIC18F66J55T-I/PT

PIC18F66J55T-I/PT - 8-bit USB MCU, 96KB Flash, 48MHz | Microchip

The Microchip PIC18F66J55T-I/PT is a high-performance 8-bit PIC microcontroller with integrated Full-Speed USB 2.0, 96 KB of Flash program memory, and 3936 bytes of RAM, housed in a 64-pin TQFP (10x10 mm) package. The device operates at up to 48 MHz internal clock and supports 4.2 V to 5.5 V supply voltage, targeting low-power and connectivity-driven embedded applications. It belongs to the PIC18F87J50 family, the first PIC18 line to combine nanoWatt power management with native Full-Speed USB, four serial ports, and 1 Mbit-class Flash density in a single die. What is a PIC18 microcontroller? A PIC18 is Microchip's 8-bit advanced Harvard-architecture RISC MCU family, sitting in the broader taxonomy of microcontrollers -> 8-bit microcontrollers -> CMOS flash MCUs -> embedded controllers. The 'J' suffix denotes the 2.0V-3.6V/4.2V-5.5V wide-range low-power family with internal voltage regulator and nanoWatt sleep modes. The PIC18F66J55 specifically targets designs that need USB connectivity, ample code space, and rich peripheral integration without an external voltage regulator. Key features include 96 KB (48K x 16) Flash program memory, 3936 bytes of RAM, 54 digital I/O pins, an integrated Full-Speed (12 Mbit/s) USB 2.0 device/host/OTG transceiver, two EUSART (LIN-capable) ports, a Master I2C port, and an SPI port capable of up to 10 Mbit/s. The device integrates a 10-bit ADC (up to 16 channels), multiple timers, and nanoWatt technology with Idle, Sleep, and deep-sleep modes for battery-friendly designs. Technically, the PIC18F66J55 uses an enhanced Harvard architecture with 16-bit instructions and 8-bit data path, a 32-level hardware stack, and an 8x8 hardware multiply engine. The on-chip 2.5V core regulator simplifies 5V single-rail designs, eliminating external LDO requirements in most cases. CIP (Core Independent Peripherals) such as CWG, MSSP, and configurable logic cells offload tasks from the CPU, increasing deterministic response for USB, motor control, and sensor interfaces. Typical applications include Full-Speed USB peripherals (HID, CDC, vendor-class devices), embedded human-interface boards with capacitive touch sensing, industrial sensor hubs with LIN/UART bridging, low-power data loggers, and consumer audio/control panels. The 64-pin TQFP footprint is friendly for hand-soldered prototypes and standard reflow production lines. When designing with the PIC18F66J55, ensure VUSB 3.3V is properly decoupled for the internal transceiver and respect the absolute maximum VDD of 5.5V. The /MCLR reset line must be pulled up through a resistor for reliable operation. MPLAB X IDE with XC8 compiler is the recommended toolchain for firmware development and debugging via ICSP. This page synthesizes distributor pricing, drop-in alternative analysis, and practical design notes not consolidated on the manufacturer datasheet or single distributor page.

询价 联系我们
PIC18F66J60T-I/PT - 8-bit MCU, 64KB Flash, Ethernet, 64-TQFP | Microchip
PIC18F66J60T-I/PT

PIC18F66J60T-I/PT - 8-bit MCU, 64KB Flash, Ethernet, 64-TQFP | Microchip

The Microchip PIC18F66J60T-I/PT is an 8-bit PIC18 microcontroller featuring an integrated 10Mbps Ethernet MAC+PHY peripheral, 64KB of Flash program memory (32K x 16), and 3808 bytes of RAM. The device operates from a 2.0V to 3.6V core supply (with 4.2V to 5.5V I/O tolerance on selected pins via internal charge-pump regulation), at a maximum clock rate of 41.667MHz (10MIPS), and is housed in a 64-pin TQFP (10x10 mm) package. It is part of the PIC18F "J" family which combines single-cycle instruction execution with on-chip networking peripherals. A microcontroller (MCU) is a single-chip processing unit integrating a CPU core, program memory (Flash), data memory (RAM), and configurable peripherals. The PIC18F family uses a Harvard RISC core, meaning separate program and data buses enable single-cycle instruction fetches even when accessing both buses concurrently. The hierarchy is: PIC18 microcontroller -> 8-bit MCU -> embedded controller -> semiconductor device. The 66J60 variant specifically adds an integrated 10/100 Ethernet MAC and 10BASE-T PHY, eliminating the need for an external network controller in connected embedded designs. Key features include 11 channels of 10-bit ADC, two USART modules, one MSSP (SPI/I2C) module, two comparators, a 16-bit timer/counter, three 8-bit timers, and the integrated Ethernet MAC/PHY with on-chip buffers. The device also has a nanoWatt power-managed operating mode for battery-friendly sleep states, and supports In-Circuit Serial Programming (ICSP) and In-Circuit Debug (ICD) for development. The on-chip 10BASE-T Ethernet peripheral directly drives the PHY magnetics and RJ45 connector, with internal DMA-driven packet buffers configurable for up to 8KB of descriptor memory. The 41.667MHz Fosc produces an industry-standard 25MHz clock output for Ethernet clocking. The nanosecond-level interrupt latency of the PIC18 core suits deterministic industrial-control applications where predictable response times matter. Typical applications include industrial automation nodes, building automation controllers, remote monitoring systems, low-cost web-enabled sensor hubs, and IP-connected HVAC equipment. The integrated Ethernet makes the 66J60 well-suited to applications where USB or Wi-Fi is over-spec but the absence of a separate network processor reduces board area and BOM cost. Operating voltage of 2.0V to 3.6V lets it run from a 3.3V rail or 2xAA cells with a boost converter. When designing with this part, allocate 3.3V rail decoupling close to every power pin and route the Ethernet differential pairs (TPTXP/TPTXN, TPRXP/TPRXN) as a 100-ohm differential pair matched to within 5mm; traces longer than 25mm require explicit magnetics footprint review per IEEE 802.3. Place the 25MHz oscillator within 5mm of the OSC1/OSC2 pins to minimize EMI. This page aggregates distributor pricing, drop-in alternatives, and field-tested design notes not consolidated in any single Microchip datasheet, helping engineers compare supply options and avoid common pitfalls before the prototype stage.

询价 联系我们
PIC18F66J65-I/PT - 8-bit 41.667MHz 96KB Flash MCU w/ Ethernet | Microchip
PIC18F66J65-I/PT

PIC18F66J65-I/PT - 8-bit 41.667MHz 96KB Flash MCU w/ Ethernet | Microchip

The Microchip Technology PIC18F66J65-I/PT is an 8-bit PIC18J-series RISC microcontroller integrating a 10Mbps Ethernet MAC+PHY, 96KB of Flash program memory, and 3808 bytes of data RAM, housed in a 64-pin TQFP package (10x10 mm). It executes instructions at 41.667 MHz (16 MIPS, 200 ns per instruction) and operates from a 4.2V to 5.5V supply. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), and a set of programmable peripherals into one IC. Within the semiconductor hierarchy, MCUs belong to the broader class of microcontrollers -> embedded processors -> digital ICs. The PIC18F family uses Microchip's enhanced Harvard RISC architecture with separate program and data buses, allowing simultaneous instruction fetch and operand access. Key features of this part include an integrated IEEE 802.3-compatible 10BASE-T Ethernet controller with 8KB Ethernet buffer, support for unicast/multicast/broadcast packet filtering, programmable wake-on-LAN for Magic Packet and pattern match, two MSSP modules (I2C/SPI), two enhanced USARTs, a 10-bit ADC with up to 16 channels, and 54 programmable digital I/O lines. The 64-pin TQFP provides generous I/O count in a moderate footprint. The integrated 10BASE-T PHY eliminates the need for an external Ethernet transceiver, which is rare in 8-bit MCUs. The PIC18J core adds hardware multiply and a 16-bit wide instruction word, giving the family 16 MIPS throughput at 41.667 MHz. This combination suits single-chip networked nodes where BOM cost and board area must be minimized. Typical applications include industrial Ethernet sensor nodes, building-automation controllers, remote-monitoring terminals, BACnet/Modbus gateways, and embedded web servers. Designers should budget for the 4.2V minimum supply (this is a 5V-only J-series part, not 3.3V-tolerant), provide a dedicated ferrite + bulk cap on the analog AVDD/AVSS rails, and reserve an external 25 MHz oscillator for the Ethernet PLL.

询价 联系我们
PIC18F66J65T-I/PT - 8-bit MCU 96KB Flash 10BASE-T Ethernet | Microchip
PIC18F66J65T-I/PT

PIC18F66J65T-I/PT - 8-bit MCU 96KB Flash 10BASE-T Ethernet | Microchip

The Microchip Technology PIC18F66J65T-I/PT is a feature-rich 8-bit PIC18 microcontroller integrating a 10 Mbps Ethernet MAC/PHY peripheral, 96 KB of Flash program memory, and 12 KB of RAM, housed in a 64-pin TQFP (PT) 10x10 mm package. Operating from 2.0 V to 3.6 V core with a 4.2 V to 5.5 V wide-range input, the device executes instructions at up to 40 MHz (10 MIPS) through a 200 ns single-cycle execution pipeline, making it suitable for deterministic networked embedded control. A microcontroller (MCU) is a single-chip computer containing a CPU, program memory (Flash), data memory (RAM), timers, communication peripherals, and I/O. The PIC18 family uses a 16-bit modified Harvard RISC architecture targeting high-throughput 8-bit applications where deterministic interrupt response matters more than raw MHz. Embedded Ethernet MCUs like the PIC18F66J65 form a sub-category at the intersection of microcontrollers and network interface ICs, combining an HTTP/TCP-friendly stack with general-purpose digital I/O. Key features include 54 digital I/O pins organized across multiple ports, an integrated 10BASE-T Ethernet MAC with HP Auto-MDIX PHY, full-speed USB 2.0 (device/host/OTG), two CAN modules (ECAN), two UART/USART modules, SPI and I2C peripherals, 16-channel 10-bit ADC, and four 16-bit timers with CCP/ECCP modules. The on-chip RTCC with timestamp enables time-stamped event logging critical for industrial controllers. An LCD driver with charge pump supports up to 132 segments, eliminating external display drivers in HMI designs. Architecture-wise, the device uses Microchip's nanoWatt XLP technology for low-power sleep modes (down to 100 nA typical standby), making it deployable in battery-backed remote monitoring nodes. Hardware AES/DES encryption accelerators and a true random number generator support secure remote-management firmware updates. The 64-pin TQFP package exposes ample peripherals, including parallel master/slave port for bus expansion. Typical applications include industrial Ethernet sensors, building automation gateways, remote monitoring controllers, intelligent HVAC nodes, networked laboratory instruments, and automotive infotainment auxiliary modules. Its combination of 10BASE-T, USB, CAN, and ADC simplifies multi-protocol field nodes that previously required a separate Ethernet controller. When designing with this MCU, allocate sufficient Flash headroom for the TCP/IP stack (roughly 40 KB of the 96 KB), use the integrated MAC/PHP+PHYs and an external 25 MHz crystal reference, and follow Microchip's TCP/IP stack Application Note AN833 for buffer sizing. EMC layout requires guarding the analog AVdd rail and isolating the Ethernet magnetics by at least 4 mm of copper-free PCB area. This page synthesizes distributor pricing, drop-in alternatives from the same PIC18 family, and practical Ethernet-PCB design notes not found in the standalone manufacturer datasheet.

询价 联系我们
PIC18F66J93-I/PT - 48MHz, 64KB Flash LCD MCU, 64-TQFP | Microchip
PIC18F66J93-I/PT

PIC18F66J93-I/PT - 48MHz, 64KB Flash LCD MCU, 64-TQFP | Microchip

The Microchip Technology PIC18F66J93-I/PT is an 8-bit PIC18J-family microcontroller that integrates a segmented LCD driver, a 12-bit A/D converter, and nanoWatt XLP power management, packaged in a 64-pin TQFP (10x10 mm). The device operates at up to 48 MHz internal clock (12 MIPS), provides 64 KB of Flash program memory, 4 KB of RAM, and 12 channels of 12-bit ADC for mixed-signal front ends. What is an 8-bit LCD microcontroller? An 8-bit LCD microcontroller is a single-chip computer that combines a CPU, non-volatile Flash memory, RAM, peripherals, and an integrated segmented LCD driver. The PIC18F66J93 belongs to the taxonomy: microcontroller -> 8-bit MCU -> PIC18 family -> PIC18J LCD sub-family -> power-managed (nanoWatt XLP). It is typically chosen when a product needs a graphical or numeric LCD readout without an external LCD controller, plus analog sensing. Key features include 64 KB of self-programmable Flash, 4 KB of RAM, integrated segmented LCD driver (up to 64 segments typical), 12-bit A/D with 12 input channels, nanoWatt XLP for ultra-low sleep currents, multiple communication peripherals (UART, SPI, I2C), and a wide operating voltage range. The integrated LCD driver eliminates an external charge-pump IC and reduces BOM cost in handheld products. From a technical-depth perspective, the PIC18F66J93 uses an enhanced Harvard architecture with a C-optimized instruction set, hardware multiplier, and 31-level hardware stack. The nanoWatt XLP technology delivers deep-sleep currents in the nanoampere range, making the device suitable for battery-powered meters. The integrated 12-bit ADC includes internal reference and automatic acquisition modes for accurate sensor measurements. Typical applications include handheld battery-powered meters, thermostats and HVAC controllers, home security panels, portable medical devices (glucometers, BP monitors), and utility metering products. The combination of integrated LCD, ADC, and low-power operation makes the part a single-chip solution for these applications. When designing with this device, plan the LCD segment routing carefully because the maximum segment count depends on the chosen pin assignment and multiplexing mode. Use Microchip's MPLAB X IDE and the PIC18F66J93 Peripheral Library to accelerate firmware development. Provide a decoupling capacitor pair (100 nF + 10 uF) close to VDD/VSS to ensure ADC and LCD reference stability. This page synthesizes distributor pricing, drop-in compatible PIC18 family alternatives from the same TQFP-64 footprint, and practical design notes not consolidated in the manufacturer datasheet alone.

询价 联系我们
PIC18F66J93T-I/PT - 8-bit LCD MCU, 64KB Flash, 12-bit ADC | Microchip
PIC18F66J93T-I/PT

PIC18F66J93T-I/PT - 8-bit LCD MCU, 64KB Flash, 12-bit ADC | Microchip

The Microchip Technology PIC18F66J93T-I/PT is a 64-pin, 8-bit PIC18 microcontroller with 64KB Flash, 3923 bytes of RAM, and an integrated segment LCD driver. It operates at up to 48 MHz (12 MIPS) and includes a 12-bit, 12-channel ADC, making it well suited to handheld metering, thermostat, and battery-powered embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and programmable peripherals. The PIC18 family uses an enhanced 8-bit RISC architecture with hardware multiply, a 16-bit instruction word, and a vectored interrupt controller. Within the PIC18 hierarchy, the J93 sub-family adds integrated segment-LCD drive, nanoWatt XLP power management, and a 12-bit ADC, positioning it between general-purpose PIC18F and PIC24/dsPIC families. Key features include 64KB (32K x 16) self-programmable Flash, 3923 bytes SRAM, 51 digital I/O, an internal oscillator, nanoWatt XLP low-power modes, an integrated LCD segment driver, and a 12-bit ADC with 12 input channels. The device operates from 2.0V to 3.6V, supporting battery-powered and portable designs. The 64-pin TQFP (10x10 mm) package offers the most pin-rich option in the family for designs needing extensive GPIO and segmented LCD drive. The PIC18F66J93 architecture uses a 16-bit-wide instruction path, 31-level hardware stack, and a priority-interrupt controller, with peripheral features including EUSART, I2C, SPI, 10-bit PWM, comparators, and a real-time clock counter. Integrated nanoWatt XLP support enables sleep currents as low as the low-nA range, extending battery life in metering applications. Typical applications include handheld meters, thermostats, home security panels, portable medical devices, utility metering, and consumer appliances with segmented LCD user interfaces. Design considerations include providing adequate decoupling near VDD/AVDD pins and following Microchip's recommended layout for LCD bias generation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

询价 联系我们
PIC18F66J94-I/PT - 64KB Flash, USB/LCD, 8-bit MCU | Microchip
PIC18F66J94-I/PT

PIC18F66J94-I/PT - 64KB Flash, USB/LCD, 8-bit MCU | Microchip

The Microchip Technology PIC18F66J94-I/PT is a 64-pin 8-bit PIC18 microcontroller delivering 16 MIPS at 64 MHz core clock, integrating 64 KB of Flash program memory and 4 KB of RAM in a 64-TQFP (10x10x1 mm) package. It combines a full-speed USB 2.0 device/embedded host controller, a segmented LCD driver (up to 256 segments), nanoWatt XLP extreme-low-power technology, and a rich analog/digital peripheral set, targeting battery-backed human-machine interface (HMI) products. The -I suffix denotes the industrial -40C to +85C operating range, while /PT denotes the 64-pin TQFP package supplied in trays. An 8-bit microcontroller (MCU) is a single-chip computer built around a CPU with an 8-bit data path, on-chip program and data memory, and integrated peripherals. Within the broader hierarchy, the PIC18F66J94 sits in the MCU > microcontroller > embedded controller > semiconductor tree, and it is a member of the PIC18 family of Microchip's 8-bit PIC architecture, the family that introduced enhanced mid-range instructions, hardware multiply, and C-friendly addressing. The part is positioned as a 'system-on-chip' for cost-sensitive applications that still need USB, an LCD glass, and ultra-low standby power. Key features include 64 KB Flash (32K x 16), 4 KB RAM, hardware 12-bit A/D, two I2C, two SPI, four USART, 10 PWM channels, 8 timers, 3 comparators, a Charge Time Measurement Unit (CTMU) for capacitive touch, a hardware Real-Time Clock/Calendar (RTCC) with Vbat domain, and an integrated charge pump that generates the LCD bias voltage. This level of analog and communication integration eliminates many external ICs that competing 8-bit designs still require. Typical applications include USB-connected industrial control panels, battery-backed metering (electricity/gas/water) with on-glass LCD, portable medical point-of-care devices, e-meter/energy-monitoring front-ends, USB medical/scientific instrument data loggers, and capacitive-touch user interfaces. The wide 2.0-3.6V Vdd range and 250 nA typical RTCC current from Vbat allow multi-year coin-cell operation in metering applications. Designers should plan PCB layout with separate analog/digital ground returns, keep the 12-bit A/D reference decoupling within 5 mm of the AVdd/AVss pins, and reserve a 4.7 uF bulk + 0.1 uF bypass pair on Vbat to preserve RTCC accuracy across battery swaps. Pin 1 orientation, I/O remapping, and PPS configuration must be set in the configuration words before the first C statement to avoid locked I/O states. This page synthesizes verified distributor pricing, pin-compatible drop-in alternatives from the same Microchip PIC18F66Jxx family, and practical design notes that go beyond the manufacturer datasheet to accelerate schematic capture and BOM selection.

询价 联系我们
PIC18F66J94T-I/MR - 64KB Flash 8-bit MCU USB/LCD | Microchip
PIC18F66J94T-I/MR

PIC18F66J94T-I/MR - 64KB Flash 8-bit MCU USB/LCD | Microchip

The Microchip PIC18F66J94T-I/MR is an 8-bit PIC18F microcontroller with 64KB of Flash program memory and 4KB of RAM, housed in a 64-pin VFQFN (MR) exposed-pad package operating at up to 64MHz (16 MIPS) from a 3.3V supply. The 'T' suffix denotes tape-and-reel packaging and '-I' designates the industrial -40C to +85C operating temperature range, while 'MR' identifies the 64-lead 9x9mm QFN package with exposed thermal pad. A microcontroller (MCU) is a single-chip computer containing a CPU, memory (Flash for program, SRAM for data), and programmable peripherals. PIC18F series devices use Microchip's enhanced 8-bit RISC architecture with a 16-bit instruction word and Harvard bus structure. This family specifically targets low-power applications via nanoWatt XLP technology and integrates segmented LCD drivers (up to 256 segments), USB 2.0 Full-Speed, and analog peripherals, replacing multiple discrete components in cost-sensitive designs. Key features of the PIC18F66J94T-I/MR include 64KB of self-programmable Flash, 4KB SRAM, integrated USB 2.0 Full-Speed transceiver with on-chip PHY, a segmented LCD controller supporting up to 256 segments, 16 MIPS throughput at 64MHz, and nanoWatt XLP power management with multiple low-power sleep modes drawing microamp-level current. The 64-pin VFQFN exposed-pad package provides low thermal resistance and compact PCB footprint for space-constrained designs. The device integrates a 10-bit ADC, multiple capture/compare/PWM modules, I2C, SPI, UART, and the USB Full-Speed transceiver with internal 3.3V regulator. Real-Time Clock/Calendar with dedicated low-power oscillator and charge time measurement unit enable battery-powered metering designs. The architecture supports self-programming for in-field firmware updates. Typical applications include USB-connected human-interface devices, electronic point-of-sale terminals with LCD displays, portable medical instrumentation, industrial data loggers, automotive dashboard clusters, and consumer white goods with segment LCD interfaces. The combination of USB, LCD, and low-power features makes this MCU a strong fit for any battery-powered product requiring both USB connectivity and a multi-segment user display. When designing with this part, ensure the exposed pad is soldered to a sufficient copper area on the PCB for thermal dissipation. The internal 3.3V regulator must be bypassed with the manufacturer-recommended capacitor values per the datasheet's electrical characteristics section to ensure USB PHY compliance. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the standalone manufacturer datasheet.

询价 联系我们
PIC18F66K22-E/MR - 8-bit 64MHz 64KB Flash MCU 64-VQFN | Microchip
PIC18F66K22-E/MR

PIC18F66K22-E/MR - 8-bit 64MHz 64KB Flash MCU 64-VQFN | Microchip

The Microchip Technology PIC18F66K22-E/MR is an 8-bit PIC18 microcontroller built on the nanoWatt XLP low-power architecture, delivering 64 MIPS performance at 64 MHz, packaged in a 64-pin VQFN (9x9 mm) with an exposed thermal pad. It integrates 64 KB of Flash program memory, 4 KB of RAM, and 1 KB of EEPROM, with a 12-bit A/D converter supporting up to 16 input channels. The -E temperature grade indicates an extended operating range of -40 C to +125 C. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, data memory, and integrated peripherals such as ADCs, timers, and communication controllers. The PIC18 family belongs to Microchip's 8-bit PIC® RISC architecture hierarchy: PIC18 -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The K-series adds the nanoWatt XLP technology for ultra-low-power operation, targeting battery-powered and energy-harvesting applications where sleep current and wake-up time dominate energy budgets. Key features include the Charge Time Measurement Unit (CTMU) for capacitive touch sensing, multiple communication peripherals (UART, SPI, I2C), enhanced PWM modules, and configurable logic cells. The device operates from 1.8 V to 5.5 V (wide Vdd) and supports self-programmability for bootloader-based firmware updates. The 12-bit ADC provides up to 16 channels for sensor interfacing. The PIC18F66K22 is built on an enhanced Harvard architecture with a modified RISC instruction set, 16-bit wide instructions, and a hardware multiplier for arithmetic-intensive tasks. Its XLP technology delivers nanoamp-level sleep currents, allowing years of operation from a single coin cell. The 64-VQFN package provides excellent thermal dissipation for sustained 64 MHz operation. Typical applications include capacitive touch human-machine interfaces (HMI), battery-powered sensor nodes, IoT edge devices, industrial control, and automotive body/comfort modules. The wide voltage range and robust peripheral set make it a flexible platform for both consumer and industrial products. When designing with this MCU, allocate a 0.1 uF decoupling capacitor adjacent to every Vdd pin and follow Microchip's recommended PCB layout for the VQFN exposed pad to achieve specified thermal performance. The CTMU requires careful calibration for reliable capacitive touch performance across environmental conditions. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.

询价 联系我们
PIC18F66K22-E/PT - 64KB Flash 8-bit MCU with nanoWatt XLP | Microchip
PIC18F66K22-E/PT

PIC18F66K22-E/PT - 64KB Flash 8-bit MCU with nanoWatt XLP | Microchip

The Microchip PIC18F66K22-E/PT is an 8-bit high-performance PIC18 microcontroller with 64 KB Flash program memory, 4 KB RAM, and 1 KB EEPROM, housed in a 64-pin TQFP (10x10 mm) package with nanoWatt XLP extreme-low-power technology. It integrates a 12-bit A/D converter with up to 16 input channels, two analog comparators, a Charge Time Measurement Unit (CTMU) for capacitive touch, multiple Enhanced USART, SPI, and I2C peripherals, and a 64 MHz internal oscillator block. The device operates from 1.8 V to 5.5 V across an industrial-grade -40 °C to +125 °C extended temperature range (suffix ‘E’) and is qualified to AEC-Q100 for automotive applications. It is pin-compatible within the PIC18F6xK22 family, allowing easy migration between 64 KB / 128 KB Flash density variants. The PIC18F66K22-E/PT provides a robust feature set including a 16-bit timer, multiple capture/compare/PWM modules, an LCD driver (on selected variants), and a charge time measurement unit ideal for capacitive touch sensing. The ‘E’ temperature grade suffix indicates the -40 °C to +125 °C operating range, and the /PT suffix designates the 64-pin TQFP (10x10 mm) plastic thin quad flat pack. The exposed-pad TQFP provides a thermal pad that improves heat dissipation for higher-clock, peripheral-intensive designs. The 64-pin TQFP package footprint is shared across the PIC18F6xK22 family, so designers can scale code density without re-laying-out the PCB. This page synthesizes distributor pricing, pin-compatible drop-in alternatives from the same Microchip K22 family, AEC-Q100 cross-reference data, and practical design notes for capacitive touch, low-power battery, and USB connectivity applications not found in the manufacturer datasheet alone. For automotive designs requiring hardware cryptography or CAN-FD, consider the related PIC18F6xK90 family; for designs needing higher Flash density, see PIC18F67K22 (128 KB) on the same footprint.

询价 联系我们
PIC18F66K22-I/MR - 64KB Flash 8-bit MCU, 64MHz, 64-VQFN | Microchip
PIC18F66K22-I/MR

PIC18F66K22-I/MR - 64KB Flash 8-bit MCU, 64MHz, 64-VQFN | Microchip

The Microchip Technology PIC18F66K22-I/MR is an 8-bit PIC18 microcontroller with 64KB of Flash program memory, 4KB of RAM, and 1KB of EEPROM, operating at up to 64MHz across a 2.5V to 5.5V supply range in a 64-pin VQFN (9x9 mm) package. It is part of the PIC18F "K22" family of enhanced-flash MCUs that integrate nanoWatt XLP extreme-low-power technology, a 12-bit ADC with up to 16 channels, and a Charge Time Measurement Unit (CTMU) for capacitive-touch sensing. A PIC18F-series microcontroller is a modified-Harvard 8-bit RISC MCU built around a 16-bit instruction word and an 8-bit data path, optimised for high code density, deterministic interrupt latency, and low power consumption. PIC18 devices sit between simple PIC16/12 controllers and the higher-performance dsPIC/PIC32 lines in the Microchip portfolio, and are typically deployed as main system controllers in cost-sensitive, low-power embedded designs spanning consumer white goods, industrial sensors, and automotive body electronics. Key features include nanoWatt XLP sleep currents below 100 nA typical, a 12-bit A/D converter with up to 16 input channels, multiple Enhanced USART, SPI, and I2C peripherals, a 16-bit Capture/Compare/PWM module, and an RTCC with independent clocking. The CTMU peripheral enables robust capacitive touch buttons, sliders, and proximity sensing using only a few external passive components. The 64-pin VQFN package exposes up to 54 digital I/O lines for parallel expansion and user-interface needs. The device uses Microchip's enhanced Flash cell technology and supports self-programmability under firmware control, plus background-debug MPLAB ICD support through two interface pins. Internal oscillator blocks (HFINTOSC up to 16 MHz and LFINTOSC at 31 kHz) allow operation without an external crystal, while a Phase-Locked Loop (PLL) is available to derive the 64 MHz system clock from internal or external sources. The architecture also integrates a 5-bit DAC, multiple comparators, and hardware CRC for data integrity. Typical applications include capacitive-touch user interfaces for white goods and consumer appliances, low-power battery-driven sensor nodes with sleep duty cycling, industrial control panels with mixed analog and digital I/O, and automotive body modules requiring AEC-style robustness under extended temperature. The wide 2.5V-5.5V supply range also makes the part suitable for both 3.3V and 5V system rails. When designing with this MCU, plan for a low-impedance ground return and decoupling of VDD/AVDD pairs within 5 mm of the respective pins. Engineers should also evaluate the RTCC current budget against their standby lifetime target, since the XLP sleep-current figure dominates battery-life calculations. This page synthesises distributor pricing, drop-in alternatives, and practical design notes that are not aggregated on the manufacturer datasheet alone.

询价 联系我们