Analog Devices

AD648KN - Dual Low-Power BiFET Op Amp | Analog Devices

料号: AD648KN ✗ 停产
1 V Vdss 400 µA Id 8-pin plastic dual in-line package Package
最小起订量: 1 |

AD648KN 概述

The Analog Devices AD648KN is a matched dual precision, low-power BiFET operational amplifier with 10 pA maximum input bias current when warmed, 400 µA maximum quiescent current, 1 V maximum offset voltage, 1 V/µs slew rate, and 1 MHz unity-gain bandwidth. It is supplied in an 8-pin plastic dual in-line package for low-noise, low-power signal conditioning.

A BiFET operational amplifier is an input stage based on field-effect transistors rather than bipolar input transistors. This input architecture provides very low bias current, making it especially useful when measuring high-impedance sources, guarding sensitive sensor nodes, filtering weak signals, or driving analog-to-digital converter inputs. The AD648 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors.

The AD648 combines low input bias current with low quiescent current, allowing its dual channels to operate without imposing excessive load on low-power sources. Its matched-pair construction supports consistent behavior across two amplifier channels, while ion-implanted FET and laser wafer trimming support precision performance. These characteristics distinguish it from general-purpose dual op amps that may consume more power or present substantially higher input bias current.

The device is specified for low offset voltage, low voltage drift, 1 V/µs slew rate, and 1 MHz unity-gain bandwidth. The combination of low noise-related input characteristics and modest bandwidth is appropriate for precision DC and low-frequency signal paths rather than high-speed video, RF, or waveform edge applications. The AD648 datasheet also identifies pin compatibility with standard dual operational-amplifier footprints, simplifying replacement and evaluation.

Typical uses include precision current-to-voltage conversion, low-level sensor amplification, medical and laboratory instrumentation, photodiode signal conditioning, battery-powered measurement systems, and dual-channel filter or buffer circuits. Because the amplifiers draw no more than 400 µA quiescent current, they are particularly attractive where every microampere affects battery life or system thermal budget.

When designing around the AD648KN, verify the input and output common-mode range, supply voltage limits, output load capability, and stability requirements from the manufacturer datasheet. Place input and output compensation components close to the relevant pins, maintain suitable grounding around high-impedance nodes, and avoid layouts that allow input leakage or switching-node currents to modulate the source impedance.

This product record combines the manufacturer's device information, exact-MPN pricing references, identified package details, and application-oriented engineering guidance. It also distinguishes genuine pin-compatible replacements from options that merely provide similar electrical functions, helping designers assess replacement risk before committing a board layout.

直接替换替代料: AD648KN ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: AD648KN (相同外形与封装尺寸) ——差异在于 Package, Mounting Type, RoHS Status, Amplifier Type, Maximum Input Bias Current.

Analog Devices
Package: 8-pin hermetically sealed metal-can TO-99
Amplifier Type: Precision dual BiFET operational amplifier
Maximum Input Bias Current: 35 pA when warmed up
对比 AD648KN →
Microchip Technology
Package: 44-QFN (8x8 mm) with exposed pad
Mounting Type: Surface Mount
RoHS Status: Compliant

AD642SH

✅ 直接替换
Analog Devices
📦 8-pin plastic dual in-line package
2 · Precision dual BiFET operational amplifier · 3500 uV · 1 MHz · 35 pA when warmed up · 500 uV maximum · 2 uV p-p · High

联系询价

查看数据手册 →

PIC18LF4420-I/ML

✅ 直接替换
Microchip Technology
📦 8-pin plastic dual in-line package
PIC 18F · PIC18 8-bit RISC · Flash · 16 KB (8K x 16) · 768 bytes · 256 bytes · 40 MHz · 2.0 V to 5.5 V

联系询价

查看数据手册 →

TL062

✅ 直接替换
📦 8-pin plastic dual in-line package
Retains the industry-standard 8-pin dual-op-amp footprint; the AD648 specifies 10 pA maximum warmed bias current and 400 µA maximum quiescent current, while exact TL062 deltas are .

📋 参考替代料(不在目录中)

AD648KN 最大额定值与电气特性

Amplifier Type Matched dual precision operational amplifier
Input Stage Ion-implanted BiFET
Number of Channels 2 channels
Maximum Quiescent Current 400 µA
Maximum Input Bias Current 10 pA when warmed
Maximum Offset Voltage 1 V
Maximum Voltage Drift 2 µV/°C
Slew Rate 1 V/µs
Unity-Gain Bandwidth 1 MHz
封装 8-pin plastic dual in-line package
安装类型 Through-hole
RoHS 状态 unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable

AD648KN 引脚配置

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
引脚 1 OUT A — Channel A output
引脚 2 -IN A — Channel A inverting input
引脚 3 +IN A — Channel A noninverting input
引脚 4 V- — Negative supply connection
引脚 5 +IN B — Channel B noninverting input
引脚 6 -IN B — Channel B inverting input
引脚 7 OUT B — Channel B output
引脚 8 V+ — Positive supply connection

典型应用

AD648KN 适用于 6 应用s: Photodiode Signal Conditioning, Precision Current Measurement, Battery-Powered Sensor Interfaces, Laboratory Instrumentation, Medical and Electrochemical Sensing, Low-Level Active Filtering.

🧩

Photodiode Signal Conditioning

The AD648KN fits low-level photodiode front ends because its maximum warmed input bias current is only 10 pA, reducing the error developed across a photodiode's very high source impedance. A transimpedance amplifier using one channel can preserve weak photocurrent signals without the input-current penalty of a conventional bipolar-input amplifier. The second channel can provide gain or active filtering. According to the Analog Devices AD648 datasheet, Rev. E, the device is fabricated with ion-implanted FET inputs, while the 400 µA maximum quiescent current keeps system consumption low. PCB guarding, clean surfaces, and controlled leakage around the high-impedance input remain essential.

⚡

Precision Current Measurement

The AD648KN is well suited to precision current measurement when the sensor has a high source impedance or the measured current is small. Its 10 pA maximum warmed bias current limits the input-current error that could otherwise create several millivolts of offset across a megohm-scale resistance. The dual-channel configuration allows one amplifier to measure the sensor signal and the other to amplify a reference or perform post-filtering. The 1 V maximum offset voltage, 2 µV/°C maximum drift, and 400 µA maximum quiescent current support stable, low-power instrumentation across changing supply and environmental conditions.

📱

Battery-Powered Sensor Interfaces

The AD648KN suits battery-powered sensor interfaces because both amplifier channels operate with no more than 400 µA maximum quiescent current. That low static demand is valuable when operating from a small battery or harvesting a weak supply, particularly if the source is a high-impedance environmental or biomedical sensor. The 10 pA maximum warmed input bias current prevents sensor-node loading, while 1 MHz unity-gain bandwidth supports filtering and modest closed-loop gain requirements. Designers should optimize quiescent-current and bias-current budgets together rather than treating either specification in isolation.

🖥️

Laboratory Instrumentation

The AD648KN is appropriate for precision laboratory instrumentation requiring low input loading and manageable power consumption. One channel can amplify a differential or single-ended sensor signal, while the second channel can buffer a reference, drive a guard circuit, or implement an active filter. Its 1 V/µs slew rate and 1 MHz unity-gain bandwidth are ample for slow measurement signals and audio-band instrumentation, although they do not target high-speed instrumentation. The matched-pair construction helps maintain consistent channel behavior when the two amplifiers perform related tasks such as differential excitation and sensing.

💊

Medical and Electrochemical Sensing

The AD648KN can serve as the input stage for medical instrumentation and electrochemical sensors because picoampere-class bias current minimizes disturbance of high-impedance sensing electrodes. The 10 pA maximum warmed input current is especially helpful when source resistance is high and the usable sensor signal is small. Its 400 µA maximum quiescent current is also attractive for compact or portable instruments. Protection, leakage current, input bias behavior, and dielectric barriers should be evaluated as a complete signal-chain requirement, since electrode-interface currents and PCB contamination can still dominate the amplifier's own input current.

🔧

Low-Level Active Filtering

The AD648KN is suitable for low-level active filtering when both signal integrity and power efficiency matter. Its 10 pA maximum warmed bias current minimizes loading of the filter's high-impedance nodes, helping preserve the designed transfer function, while the 1 MHz unity-gain bandwidth provides adequate bandwidth for many precision and audio-band filter sections. The 1 V/µs slew rate limits large-signal distortion for moderate amplitudes. Component tolerances, feedback-network noise, and the amplifier's real noise spectrum should be evaluated together because low bias current alone does not guarantee low total output noise.

推荐产品汇总

AD642 Pin-compatible low-power dual operational-amplifier option 用于: Photodiode Signal Conditioning, Precision Current Measurement, Laboratory Instrumentation, Medical and Electrochemical Sensing, Low-Level Active Filtering LF442 Industry-standard pin-compatible dual operational amplifier 用于: Photodiode Signal Conditioning, Battery-Powered Sensor Interfaces, Laboratory Instrumentation, Low-Level Active Filtering TL062 Pin-compatible dual amplifier for legacy circuit revisions 用于: Precision Current Measurement, Battery-Powered Sensor Interfaces, Medical and Electrochemical Sensing
What is the AD648KN?
The AD648KN is a matched dual precision, low-power BiFET operational amplifier from Analog Devices, supplied in an 8-pin plastic dual in-line package. According to the Analog Devices AD648 datasheet, Rev. E, it combines a maximum input bias current of 10 pA when warmed with a maximum quiescent current of 400 µA. It is intended for high-impedance sensing, precision current measurement, low-level signal conditioning, and dual-channel buffer or filter applications where low input current and low power consumption are more important than high bandwidth.
What are the key specifications of AD648KN that engineers should know?
The AD648KN provides two matched amplifier channels, 10 pA maximum warmed input bias current, 400 µA maximum quiescent current, 1 V maximum offset voltage, 2 µV/°C maximum drift, 1 V/µs slew rate, and 1 MHz unity-gain bandwidth. According to the Analog Devices AD648 datasheet, Rev. E, ion-implanted FET inputs and laser wafer trimming support precision operation. The 8-pin plastic dual in-line package is intended for through-hole, low-noise precision circuits rather than high-speed or surface-mount production designs.
Where can I download the AD648KN datasheet PDF?
The official AD648KN technical documentation is available through the Analog Devices AD648 product page at https://www.analog.com/en/products/ad648.html. The associated data sheet is identified as Rev. E and covers the dual precision, low-power BiFET operational-amplifier family, including electrical characteristics, pin descriptions, package options, and ordering information. Use the manufacturer data sheet as the controlling document for supply limits, common-mode range, output swing, and absolute maximum ratings when planning a new circuit.
Where can I find the AD648KN pinout?
The AD648KN uses an 8-pin dual in-line operational-amplifier pinout with each channel providing an output, inverting input, and noninverting input, plus shared positive and negative supply pins. According to the Analog Devices AD648 datasheet, Rev. E, pins 1 and 7 are the amplifier outputs, pins 2 and 6 are inverting inputs, pins 3 and 5 are noninverting inputs, pin 4 connects to the negative supply, and pin 8 connects to the positive supply. Confirm the final PCB mapping against the package drawing.
Why is the AD648KN suitable for high-impedance sensor measurements?
The AD648KN is suitable for high-impedance measurements because its input bias current is limited to 10 pA maximum when warmed. According to the Analog Devices AD648 datasheet, Rev. E, bias current is guaranteed over the device's common-mode voltage range. Low input current reduces the error voltage produced when current flows through a high source resistance, making the amplifier useful for photodiode, electrochemical sensor, capacitive sensing, and precision divider interfaces. Board cleanliness and guarding remain important because leakage at the PCB can dominate at picoampere current levels.
Is AD648KN suitable for battery-powered instrumentation?
Yes, the AD648KN is suitable for battery-powered instrumentation because its maximum quiescent current is only 400 µA for both amplifier channels. According to the Analog Devices AD648 datasheet, Rev. E, the low quiescent current complements the AD648's 10 pA maximum warmed input bias current. These characteristics help preserve battery capacity and reduce the loading of low-level sensors. The 1 MHz unity-gain bandwidth and 1 V/µs slew rate are sufficient for precision DC, slow-signal, filtering, and instrumentation-amplifier applications, but not demanding high-speed waveform tasks.
AD648KN vs AD642 — which is better for low-power precision circuits?
The AD648KN is the stronger choice when maximum warmed input bias current of 10 pA and a maximum quiescent current of 400 µA are critical priorities. The Analog Devices AD648 documentation identifies both AD648-family and AD642 devices as industry-standard dual-op-amp-compatible choices, but it does not establish that their electrical ratings are identical. The AD648KN should therefore be selected when its specified low-bias, low-power performance is explicitly needed. Verify the AD642 data sheet for offset, bandwidth, supply, and common-mode requirements before substituting it.
AD648KN vs LF442 — which is better for precision instrumentation?
The AD648KN is generally the more precise choice when low input bias current and low power consumption are decisive. According to the Analog Devices AD648 datasheet, Rev. E, the AD648KN is pin compatible with the LF442 and provides a maximum warmed input bias current of 10 pA and a maximum quiescent current of 400 µA. The LF442 can remain attractive when its own ratings are adequate and the design benefits from broader legacy availability. Confirm offset, drift, bandwidth, supply range, and output swing before treating the two as interchangeable.
What is the best drop-in replacement for AD648KN?
The identified drop-in choices for the AD648KN are the AD642, LF442, and TL062, because the Analog Devices AD648 datasheet identifies pin compatibility with these industry-standard dual operational amplifiers. The best replacement depends on which specifications dominate: bias current, quiescent current, offset, drift, bandwidth, common-mode range, and supply rating. If those requirements are already satisfied, the AD642 is the closest same-manufacturer option; LF442 and TL062 provide legacy alternatives. Validate every operating limit before replacement.
Can TL062 replace AD648KN without changing the PCB?
The TL062 can be a pin-compatible replacement for the AD648KN because the Analog Devices AD648 datasheet identifies it as an industry-standard dual op amp with compatible pins. However, pin compatibility does not guarantee equal precision or power consumption. According to the AD648 documentation, the AD648KN is specified at 10 pA maximum warmed bias current and 400 µA maximum quiescent current. Confirm that the TL062 satisfies the source-loading error, offset, drift, bandwidth, output-swing, and supply requirements of the original design.
When should I choose AD648KN over LF442 or TL062?
Choose the AD648KN when picoampere input bias current and no more than 400 µA quiescent current are central requirements. According to the Analog Devices AD648 datasheet, Rev. E, the AD648KN also offers matched-channel construction, 1 V/µs slew rate, and 1 MHz unity-gain bandwidth. LF442 or TL062 may be preferable when their verified ratings meet the application and procurement considerations favor those legacy devices. For very high source impedances, compare actual bias-current behavior over temperature rather than relying only on maximum headline values.
Is AD648KN the same as AD642?
No, the AD648KN and AD642 are related dual operational amplifiers with compatible pin arrangements, but they are not the same device. According to the Analog Devices AD648 datasheet, Rev. E, the AD648 offers 10 pA maximum warmed input bias current, 400 µA maximum quiescent current, 1 V/µs slew rate, and 1 MHz unity-gain bandwidth. The AD642 should be selected only after its offset, drift, bandwidth, noise, common-mode range, and supply limits are compared against the original AD648 requirements.
What can replace AD648KN in an 8-pin dual op amp circuit?
The AD642, LF442, and TL062 are the identified pin-compatible replacements for an 8-pin AD648KN circuit. The Analog Devices AD648 datasheet, Rev. E, specifically states that the AD648 is pin compatible with these industry-standard dual operational amplifiers. A direct engineering swap still requires checking critical parameters: the AD648's 10 pA maximum warmed bias current, 400 µA maximum quiescent current, 1 V maximum offset voltage, 1 V/µs slew rate, and 1 MHz unity-gain bandwidth.
Where can I buy AD648KN and what is the lead time?
Use the Request a Quote form on this page to ask for AD648KN availability, current unit pricing, minimum order quantity, and production lead time. Because the manufacturer marks the AD648 family as not recommended for new designs, engineers should also request the lifecycle roadmap and any last-time-buy status before starting a new production release. The product remains relevant for repair and existing embedded designs, but availability and sourcing terms should be confirmed for the exact 8-pin AD648KN ordering code rather than inferred from another package variant.
What is the price of AD648KN?
The current AD648KN price is generated through the Request a Quote form on this page so that the commercial response reflects the selected quantity, package code, and available inventory. The manufacturer identifies the AD648 family as not recommended for new designs, which makes lifecycle-aware sourcing important. Submit one request for the exact AD648KN MPN and state your required quantity, delivery location, and target date so the quotation can confirm both commercial terms and any remaining supply constraints.
Is AD648KN currently in stock?
AD648KN inventory should be confirmed through the Request a Quote form on this page rather than inferred from general family listings. The manufacturer marks the AD648 as not recommended for new designs, and a stock status for the exact 8-pin plastic DIP ordering code may differ from other AD648 package variants. Include your required quantity and delivery schedule in the request. For programs that cannot tolerate legacy supply uncertainty, request lifecycle confirmation and evaluate a currently supported precision low-power BiFET amplifier before layout release.
Does AD648KN meet RoHS and automotive qualification requirements?
The AD648KN is an industrial-style precision analog amplifier rather than an automotive-qualified device, so AEC-Q100 qualification is not applicable. RoHS and REACH status are listed as unknown because the device information does not provide an explicit compliance declaration for this exact ordering code. Before purchasing, request the current manufacturer compliance statement and check the latest product-documentation change records. Do not infer lead-free, halogen-free, or conflict-minerals status from the package family or from another AD648 variant.

工程参考数据: AD648KN ——对比、设计指导和合规信息。

选型指南

Choose the AD648KN for precision, low-power circuits where input loading, quiescent demand, offset, and drift matter. Its 10 pA maximum warmed input bias current is especially useful with photodiodes, electrochemical sensors, high-value dividers, and other high-impedance sources, while the 400 µA maximum quiescent current benefits portable instruments. Consider the AD642 when a same-manufacturer, pin-compatible legacy design is acceptable and its electrical limits meet the original requirements. LF442 or TL062 may be practical when maintaining an older design takes priority, but verify their bias current, offset, drift, bandwidth, common-mode range, supply rating, and output swing. For new high-speed or surface-mount products, the AD648's 1 MHz bandwidth and 8-pin through-hole package may instead justify selecting a newer supported amplifier family rather than preserving the legacy footprint.

与替代料对比

参数 本产品 AD642 LF442 TL062
Package 8-pin plastic dual in-line package 8-pin plastic dual in-line package 8-pin plastic dual in-line package 8-pin plastic dual in-line package
Brand Analog Devices Analog Devices Texas Instruments Texas Instruments
Amplifier Configuration Dual operational amplifier Dual operational amplifier Dual operational amplifier Dual operational amplifier

关键差异点

  • Lower input loading for picoampere-level sensing (对比 AD642)
  • Precision performance with limited power consumption (对比 LF442)
  • Matched dual-channel BiFET implementation (对比 TL062)

设计说明

Do not assume that an 8-pin footprint guarantees an electrical match. The AD648KN is specified at 10 pA maximum warmed input bias current, 400 µA maximum quiescent current, 1 V maximum offset voltage, 2 µV/°C maximum drift, 1 V/µs slew rate, and 1 MHz unity-gain bandwidth. Before replacing it with AD642, LF442, or TL062, compare bias current, offset, drift, common-mode range, output swing, supply limits, and stability requirements against the original circuit.

For high-impedance sources, surround the input connection with a guard ring driven by the corresponding amplifier output where the circuit topology permits it. Keep the sensitive node short, minimize solder flux and contamination, and avoid placing the input trace near switching nodes or digital return paths. Although the AD648's warmed bias current can reach only 10 pA, PCB leakage and surface contamination can produce comparable errors and may dominate the amplifier's specification.

Use the 400 µA maximum quiescent current as the baseline for static power budgeting, but include load current, dual-channel operation, and leakage from external circuitry. At a nominal 5 V supply, the static device current corresponds to approximately 2 mW before external loading; this is an estimate based on the published maximum quiescent current and assumes both amplifier channels are active. Confirm supply limits and bypass requirements from the manufacturer data sheet before fixing the system power budget.

The 1 MHz unity-gain bandwidth makes the AD648KN suitable for precision and low-frequency paths, not high-speed waveform work. Check the intended noise-gain curve, required phase margin, and closed-loop bandwidth against the 1 V/µs slew rate. For a 1 V output step, the minimum rise time is approximately 1 µs as an estimate from slew rate; actual settling also depends on small-signal bandwidth, feedback components, load, and the selected compensation network.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The manufacturer identifies the AD648 family as not recommended for new designs. Explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not found for the exact AD648KN ordering code.

数据核验日期: 2026-11-18 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

AD648KN datasheet AD648KN pinout AD648KN datasheet pdf AD648KN equivalent AD648KN replacement AD648KN cross reference AD648KN price AD648KN stock Analog Devices AD648KN AD648KN vs AD642 AD648KN vs LF442 AD648KN 8-pin DIP

相关元器件 & 术语

Analog Devices AD648 AD648KN AD642 LF442 TL062 dual operational amplifier precision operational amplifier BiFET field-effect transistor input stage low-dropout current input low-power analog IC signal conditioning high-impedance sensor photodiode electrochemical sensor transimpedance amplifier active filter input bias current quiescent current offset voltage voltage drift slew rate unity-gain bandwidth 8-pin plastic dual in-line package
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情