ADM4851AR - 500 kbps RS-485/422 Transceiver | Analog Devices
料号: ADM4851AR ✓ 量产中ADM4851AR 概述
An RS-485 transceiver is an interface IC that converts logic-level signals into balanced differential signals for reliable communication over longer cable runs. It belongs to the RS-485 and RS-422 interface-transceiver hierarchy, which forms part of broader data communication and interface semiconductors. Balanced differential signaling improves noise immunity by rejecting common-mode voltage that appears equally on both conductors.
The ADM4851AR family combines several bus-focused features. It supports operation at up to 500 kbps, uses reduced slew rates for lower EMI, and provides true fail-safe receiver behavior. The half-duplex configuration allows a single differential bus pair to carry data in both directions when only one device transmits at a time. Its 5 V supply operation and 8-lead SOIC package suit conventional industrial, instrumentation, and embedded communication systems.
Technical performance is centered on balancing data throughput against signal integrity. A 500 kbps maximum data rate supports moderate-speed industrial links without the edge rates associated with the faster members of the ADM485x family. The controlled transition rate helps limit common-mode energy and ringing on unterminated or imperfectly terminated cables, although correct bus topology and termination remain essential for reliable operation.
Typical applications include industrial control networks, factory automation equipment, building automation controllers, RS-422 point-to-point links, instrumentation gateways, data acquisition systems, and embedded serial buses. The transceiver can also participate in multidrop RS-485 networks when the system designer observes the recommended addressing, biasing, termination, and idle-state requirements.
Design consideration: place the transceiver close to the connector and route the differential pair as a tightly coupled pair over a continuous reference plane. Use the bus termination and fail-safe biasing specified by the manufacturer datasheet. Do not add substantial capacitive loading or long unprotected stubs, because those changes can degrade the controlled slew rate and reduce reliable communication distance.
This page consolidates the ADM4851AR family specifications, same-footprint alternatives, application guidance, and practical bus-layout considerations into an engineering-focused selection reference. It also distinguishes speed and duplex trade-offs so designers can choose the correct ADM485x member without assuming that every family member is an interchangeable replacement.
直接替换替代料: ADM4851AR ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ADM4851AR (相同外形与封装尺寸) ——差异在于 Product Type, Signal Type, Package, Maximum Data Rate, Communication Mode.
ADM4851AR 规格参数
| Product Type | RS-485/RS-422 differential line transceiver |
| 电源电压 | 5 V |
| Maximum Data Rate | 500 kbps |
| Communication Mode | Half-duplex |
| Standards Compatibility | EIA RS-485 and EIA RS-422 compliant |
| Receiver Fail-Safe Behavior | True fail-safe receiver |
| Transition Rate Control | Reduced slew rate for low EMI |
| Bus Topology | Multipoint bus transmission line |
| Signal Type | Differential |
| 封装 | 8-lead SOIC |
| 安装类型 | Surface Mount |
| Lead Count | 8 leads |
ADM4851AR 8-lead soic 引脚配置指南
ADM4851AR(8-lead soic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ADM4851AR.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ADM4851AR 适用于 6 应用s: Industrial Control Networks, Building Automation Controllers, Data Acquisition Systems, RS-422 Point-to-Point Links, Instrumentation Gateways, Embedded Serial Bus Interfaces.
Industrial Control Networks
The ADM4851AR fits moderate-speed industrial control links that require differential signaling and reliable operation over factory cable runs. Its 500 kbps maximum data rate is substantially above the 115 kbps ADM4850AR class, allowing it to support faster status, configuration, and supervisory data exchanges. The reduced slew rate helps lower EMI, while true fail-safe receiver behavior provides defined logic during bus-idle and driver-disabled intervals. The 8-lead SOIC package also simplifies assembly into compact controller and I/O modules.
Building Automation Controllers
The ADM4851AR is suitable for building automation equipment that connects sensors, actuators, and controllers over an RS-485 network. A 500 kbps link can consolidate frequent telemetry and command traffic while the balanced differential interface reduces susceptibility to common-mode noise found near motors, relays, and switching power circuits. Reduced slew rate limits radiated emissions, and true fail-safe reception improves behavior when controllers reboot or leave the bus undriven. Its 8-lead SOIC footprint supports compact DIN-rail and wall-mount controller boards.
Data Acquisition Systems
The ADM4851AR can connect laboratory or industrial data-acquisition modules to a central controller when moderate throughput and noise immunity are priorities. Its 500 kbps limit supports transfer of measurement commands and sampled status without requiring the multi-megabit capability of faster ADM485x variants. Differential signaling helps reject common-mode voltage encountered near analog circuitry, while the controlled slew rate reduces high-frequency cable noise. The 8-lead SOIC package makes it practical to place one transceiver near a terminal block or instrumentation connector.
RS-422 Point-to-Point Links
The ADM4851AR can be used in RS-422 point-to-point equipment links where balanced signaling and a 500 kbps data rate are appropriate. The differential receiver improves common-mode noise rejection, and the reduced slew rate helps maintain cleaner transitions over longer cable paths. True fail-safe receiver behavior is useful when the remote transmitter may be disconnected or powered down. The half-duplex configuration should be managed so that only one endpoint drives the pair at any instant.
Instrumentation Gateways
The ADM4851AR is appropriate for gateways that bridge older RS-485 equipment to a faster local processor. A 500 kbps bus rate accommodates routine polling, configuration, and diagnostic traffic while avoiding the footprint and power requirements of a multi-megabit transceiver. The reduced edge rate is advantageous in panels containing relay contacts, display electronics, and switching supplies. Placing the device near the field-side connector keeps the differential route short and limits the area that can pick up external electromagnetic interference.
Embedded Serial Bus Interfaces
The ADM4851AR can extend a microcontroller or embedded controller to an external RS-485 bus using its 500 kbps capability and 5 V operation. It is well suited to configuration ports, sensor networks, and distributed peripheral control where logic-level UART signals must be converted to balanced differential signaling. The true fail-safe receiver gives the firmware a predictable state when no peripheral is transmitting. Designers should use the manufacturer control and biasing guidance to control bus direction and prevent multiple transmitters from driving the line simultaneously.
工程参考数据: ADM4851AR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ADM4850AR | ADM4854AR |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-lead SOIC | 8-lead SOIC | 8-lead SOIC |
| Maximum Data Rate | 500 kbps | 115 kbps | 115 kbps |
| Supply Voltage | 5 V | 5 V | 5 V |
| Standards Compatibility | RS-485 and RS-422 compliant | RS-485 and RS-422 compliant | RS-485 and RS-422 compliant |
| Reduced Slew Rate | Yes | Yes | Yes |
| True Fail-Safe Receiver | Yes | Yes | Yes |
| Communication Mode | Half-duplex | Half-duplex | Half-duplex |
关键差异点
- Higher family data rate (对比 ADM4850AR)
- Higher family data rate (对比 ADM4854AR)
- EMI-conscious edge control (对比 ADM4850AR)
设计说明
Route the differential pair as a tightly coupled pair over a continuous ground or reference plane, and place the ADM4851AR close to the external connector. Minimize stub lengths and keep the bus-side path away from switching nodes, crystal circuitry, and high-current relay routes. The reduced slew rate reduces EMI, but it cannot compensate for an unbalanced pair, an excessively long stub, or a sharply interrupted return path.
Confirm that the application actually supports the selected ADM485x family member. ADM4851AR reaches 500 kbps, whereas ADM4850AR and ADM4854AR are identified as 115 kbps devices. Substituting the slower parts into a timing-critical 500 kbps design can cause framing errors even though the package and principal interface functions appear similar. Verify data timing, bus direction control, and fail-safe behavior in the manufacturer pin descriptions.
Apply the termination and fail-safe biasing arrangement specified for the selected bus topology. Avoid long unterminated branches, excessive capacitive loading, and multiple termination points. Keep the controlled edge rate useful by using a topology suitable for multipoint RS-485 rather than creating star branches from the transceiver. This minimizes reflections and common-mode conversion that can degrade both the data link and adjacent equipment.
Use a stable 5 V supply and place the recommended bypass capacitance at the ADM4851AR power pin. Check the datasheet limits for supply voltage, ground current, and output-current behavior before using the transceiver with unusually long cables or heavy bus loading. Provide appropriate protection at externally accessible connectors when the installation exposes the bus to surge, electrostatic discharge, or other industrial transients.
合规信息
The manufacturer and distributor information identifies the ADM4851 family but does not provide a definitive compliance declaration for the exact ADM4851AR ordering code in the cited results. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status therefore remain unknown.