ATSAMD20G14A-MUT - 32-bit ARM Cortex-M0+ MCU, 48MHz, 16KB Flash | Microchip
料号： ATSAMD20G14A-MUT ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $2.34 | $2.34 |
| 10 | $2.1 | $21.00 |
| 100 | $1.85 | $185.00 |
| 500 | $1.62 | $810.00 |
| 1,000 | $1.45 | $1,450.00 |
| 2,500 | $1.28 | $3,200.00 |
ATSAMD20G14A-MUT 概述
A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), working memory (SRAM), and programmable peripherals. The Cortex-M0+ core sits at the lowest end of the ARM Cortex-M family, optimized for minimal gate count, deterministic interrupt latency, and ultra-low active power. The SAM D20 family is positioned as a low-power, high-performance replacement for 8-bit and 16-bit MCUs in home automation, consumer, metering, and industrial applications. Within the SAM D20 family, the -G14 variant represents the 48-pin 16 KB Flash tier.
Key features of the ATSAMD20G14A-MUT include a 48 MHz maximum CPU clock, single-cycle 32-bit multiply, 14-channel 12-bit ADC with 350 kSamples/s throughput, up to six SERCOM (serial communication) interfaces configurable as UART, SPI, or I2C, a full-speed USB 2.0 device controller, a 24-bit timer/counter, RTC, and brown-out detection. The peripheral event system allows direct hardware-level signaling between peripherals without CPU intervention, which reduces latency and current draw.
Typical applications include smart-home sensor nodes, low-power wireless IoT endpoints, industrial control and metering front-ends, USB-CDC human-interface devices, and battery-powered wearables. The integrated USB 2.0 full-speed controller makes the ATSAMD20G14A-MUT a strong fit for low-cost USB devices, while the Cortex-M0+ core delivers more than 60 DMIPS of processing while consuming only a few milliamps active.
When designing with this MCU, verify that your firmware uses an Atmel/Microchip DFP device pack and a compatible toolchain (e.g., MPLAB X IDE with the XC32 compiler or Atmel Studio with GCC). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
直接替换替代料： ATSAMD20G14A-MUT ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： ATSAMD20G14A-MUT （相同外形与封装尺寸） ——差异在于 ADC, Family, Package, Mounting Type, RoHS Status.
快速对比工具——选择替代料号进行并排对比：
ATSAMD20G14A-MU
✅ 直接替换📋 参考替代料（不在目录中）
ATSAMD20G14A-MNT
✅ 直接替换✓ 有现货
$1.38 / 个
查看数据手册 →ATSAMD20G14A-MN
✅ 直接替换✓ 有现货
$1.89 / 个
查看数据手册 →ATSAMD20E15A-MUT
✅ 直接替换📋 参考替代料（不在目录中）
ATSAMD20G14A-AU
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
ATSAMC20G16A-MUT
✅ 直接替换📋 参考替代料（不在目录中）
ATSAMD20G14A-MUT 最大额定值与电气特性
| Core | ARM Cortex-M0+ |
| Architecture | 32-bit RISC |
| Family | SAM D20G |
| Maximum CPU Frequency | 48 MHz |
| CoreMark/MHz | 2.14 |
| Flash Program Memory | 16 KB (16K x 8) |
| SRAM | 2 KB |
| 封装 | 48-QFN (7x7 mm) with exposed pad |
| 引脚数量 | 48 |
| Supply Voltage Range | 1.62 V to 3.6 V |
| 工作温度范围 | -40 C to +85 C (industrial) |
| ADC | 12-bit, up to 350 kSamples/s |
| Communication Interfaces | Up to 6 SERCOM (UART/SPI/I2C), USB 2.0 Full-Speed Device |
| 安装类型 | Surface Mount (QFN) |
| MSL 等级 | 3 (168 hours) |
| RoHS 状态 | Compliant |
ATSAMD20G14A-MUT 引脚配置
| 引脚 1 | PA00 — I/O / SERCOM1[0] / ADC[0] |
| 引脚 2 | PA01 — I/O / SERCOM1[1] / ADC[1] |
| 引脚 3 | PA02 — I/O / SERCOM2[0] / ADC[2] |
| 引脚 4 | PA03 — I/O / SERCOM2[1] / ADC[3] |
| 引脚 5 | PA04 — I/O / SERCOM0[0] / ADC[4] / VDIV |
| 引脚 6 | PA05 — I/O / SERCOM0[1] / ADC[5] |
| 引脚 7 | PA06 — I/O / SERCOM0[2] / ADC[6] |
| 引脚 8 | PA07 — I/O / SERCOM0[3] / ADC[7] |
| 引脚 9 | VDDIO — Digital I/O supply voltage |
| 引脚 10 | GND — Ground |
| 引脚 11 | PA08 — I/O / SERCOM2[0] / NMI |
| 引脚 12 | PA09 — I/O / SERCOM2[1] / ADC[9] |
| 引脚 13 | PA10 — I/O / SERCOM2[2] / ADC[10] |
| 引脚 14 | PA11 — I/O / SERCOM2[3] / ADC[11] |
| 引脚 15 | VDDIN — Voltage regulator input supply |
| 引脚 16 | GND — Ground |
| 引脚 17 | PA12 — I/O / SERCOM4[0] / ADC[12] |
| 引脚 18 | PA13 — I/O / SERCOM4[1] / ADC[13] |
| 引脚 19 | PA14 — I/O / SERCOM4[2] / ADC[14] |
| 引脚 20 | PA15 — I/O / SERCOM4[3] / ADC[15] |
| 引脚 21 | PA16 — I/O / SERCOM3[0] / I2S_SD0 |
| 引脚 22 | PA17 — I/O / SERCOM3[1] / I2S_MCK0 |
| 引脚 23 | PA18 — I/O / SERCOM3[2] / I2S_FS0 |
| 引脚 24 | PA19 — I/O / SERCOM3[3] / I2S_SCK0 |
| 引脚 25 | PA20 — I/O / SERCOM5[2] / GCLK_IO6 |
| 引脚 26 | PA21 — I/O / SERCOM5[3] / GCLK_IO7 |
| 引脚 27 | PA22 — I/O / SERCOM3[0] / TC4[0] |
| 引脚 28 | PA23 — I/O / SERCOM3[1] / TC4[1] |
| 引脚 29 | PA24 — USB_DM |
| 引脚 30 | PA25 — USB_DP |
| 引脚 31 | PA27 — I/O / GCLK_IO0 |
| 引脚 32 | GND — Ground |
| 引脚 33 | VDDIN — Voltage regulator input supply |
| 引脚 34 | RESET — Reset input (active low) |
| 引脚 35 | PA28 — I/O / GCLK_IO0 / TC1[2] |
| 引脚 36 | PA29 — I/O / GCLK_IO1 / TC1[3] |
| 引脚 37 | PA30 — I/O / SWCLK / TC2[0] |
| 引脚 38 | PA31 — I/O / SWDIO / TC2[1] |
| 引脚 39 | PB00 — I/O / SERCOM5[2] |
| 引脚 40 | PB01 — I/O / SERCOM5[3] |
| 引脚 41 | PB02 — I/O / SERCOM5[0] / ADC[0] |
| 引脚 42 | PB03 — I/O / SERCOM5[1] / ADC[1] |
| 引脚 43 | PB04 — I/O / SERCOM4[0] / ADC[12] |
| 引脚 44 | PB05 — I/O / SERCOM4[1] / ADC[13] |
| 引脚 45 | PB06 — I/O / SERCOM4[2] / ADC[14] |
| 引脚 46 | PB07 — I/O / SERCOM4[3] / ADC[15] |
| 引脚 47 | PB08 — I/O / SERCOM4[0] |
| 引脚 48 | PB09 — I/O / SERCOM4[1] |
| 引脚 EP | GND_PAD — Exposed thermal pad, must be soldered to ground for thermal dissipation |
典型应用
ATSAMD20G14A-MUT 适用于 6 应用s: USB Human-Interface Device (HID), Smart-Home Sensor Node, Industrial Control & Metering Front-End, USB-CDC Communication Device, Battery-Powered Wearable Device, Low-Cost Wireless IoT Endpoint.
USB Human-Interface Device (HID)
The ATSAMD20G14A-MUT fits USB HID designs because the integrated USB 2.0 full-speed device controller with on-chip transceiver eliminates the external PHY, BOM cost, and PCB area. With 48 MHz CPU clock and 16 KB Flash, the MCU runs the standard USB stack plus vendor HID report logic with comfortable headroom. Placed on a small 4-layer PCB with 4.7 uF VBUS decoupling and the 22 ohm DM/DP series resistors, the device delivers reliable HID-class enumeration at 12 Mbps while drawing under 15 mA active.
推荐
Smart-Home Sensor Node
For Zigbee/BLE-attached sensor nodes, the ATSAMD20G14A-MUT offers six SERCOM ports that map cleanly to SPI-attached sensors, I2C-attached environmental ICs, and a UART-linked wireless coprocessor. The Cortex-M0+ core running 48 MHz executes 12-bit ADC reads at up to 350 kSamples/s, suitable for thermistor and battery-monitor sampling. With SleepWalking peripherals and the Event System, the node can idle below 2 uA between sensor interrupts, extending coin-cell runtime by 5-10x over 8-bit baselines.
推荐
Industrial Control & Metering Front-End
The ATSAMD20G14A-MUT suits industrial metering front-ends thanks to its 12-bit ADC, RTC calendar, and 1.62-3.6 V supply range covering battery and bus-powered meters. Operating from -40 C to +85 C, the part meets industrial temperature expectations, while the QFN-48 (7x7) exposed pad gives reliable thermal performance under continuous ADC sampling. Placed behind an isolation barrier with the 12-bit ADC monitoring shunt current and bus voltage, the MCU drives calibration and display update tasks with predictable interrupt latency.
推荐
USB-CDC Communication Device
For USB-CDC virtual COM ports, the ATSAMD20G14A-MUT provides full-speed USB and 6 SERCOM channels at a unit cost typically below $2.30 in volume. The 16 KB Flash easily fits the Microchip CDC stack plus vendor command handling. Designers place a 5 V tolerant level shifter on the VBUS pin and route DM/DP with controlled 90 ohm differential impedance for USB 2.0 compliance. The MCU then appears as a virtual COM port on host PCs without external driver installation on modern Windows/macOS/Linux.
推荐
Battery-Powered Wearable Device
The ATSAMD20G14A-MUT's 1.62 V minimum supply and deep-sleep current profile support coin-cell-powered wearables. The Event System allows sensor interrupts to wake the core without CPU overhead, while the integrated RTC handles timekeeping across shutdown. At 1.8 V operation the MCU draws only a few mA active and under 2 uA in BACKUP mode with RTC running, supporting weeks of standby life. The 7x7 QFN footprint is small enough for wrist-strap form factors.
推荐
Low-Cost Wireless IoT Endpoint
For Wi-Fi/BLE gateway-attached endpoints, the ATSAMD20G14A-MUT runs the local sensor sampling and protocol framing while an external coprocessor handles the radio. Its SERCOM, ADC, and PWM channels cover most endpoint sensor interfaces; the 48 MHz Cortex-M0+ handles TLS/UDP framing for the host protocol. Compared to a discrete 8-bit MCU + ADC design, the SAM D20G14 reduces BOM by one IC and saves PCB area, with firmware upgradeability via bootloader over USB or UART.
推荐
推荐产品汇总
工程参考数据： ATSAMD20G14A-MUT ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ATSAMD20G14A-MU | ATSAMD20G14A-MNT | ATSAMD20G14A-MN | ATSAMD20E15A-MUT | ATSAMD20G14A-AU |
|---|---|---|---|---|---|---|
| Package | 48-QFN (7x7 mm) | 48-QFN (7x7) - same | 48-QFN (7x7) - same | 48-QFN (7x7) - same | 48-QFN (7x7) - same | 48-TQFP (7x7) - same pin count, different body |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | ARM Cortex-M0+ | ARM Cortex-M0+ (same) | ARM Cortex-M0+ (same) | ARM Cortex-M0+ (same) | ARM Cortex-M0+ (same) | ARM Cortex-M0+ (same) |
| Max CPU Clock | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash | 16 KB | 16 KB | 16 KB | 16 KB | 32 KB (+100%) | 16 KB |
| SRAM | 2 KB | 2 KB | 2 KB | 2 KB | 4 KB (+100%) | 2 KB |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +125 C (extended) | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| USB 2.0 Controller | Full-speed device integrated | Full-speed integrated | Full-speed integrated | Full-speed integrated | Full-speed integrated | Full-speed integrated |
关键差异点
- Integrated USB 2.0 full-speed controller with on-chip transceiver （对比 PIC16F631-I/SS)
- 32-bit Cortex-M0+ core running 48 MHz with 2.14 CoreMark/MHz （对比 PIC16F630-I/SL)
- 6 SERCOM channels configurable as UART/SPI/I2C plus USB （对比 ATSAMD10D14A-MNT)
设计说明
The 48-QFN (7x7) package has an exposed thermal pad (EP) on pin 49 that must be soldered to a ground copper pour of at least 4x4 thermal vias for heat dissipation. Per Microchip's SAM D20 hardware-design guide, place a 1 uF and a 100 nF decoupling capacitor pair within 2 mm of every VDDIN/VDDIO pin pair, with the smaller capacitor closest to the IC. Route the USB DM/DP pair as a 90 ohm differential trace with controlled impedance and length-matched to within 150 mil.
The ATSAMD20G14A-MUT's internal 1.2 V LDO draws power from VDDIN (1.62-3.6 V) and supplies the core logic. Estimated: with the core running at 48 MHz, all six SERCOM active, and the ADC sampling, the MCU consumes roughly 7-9 mA active. In STANDBY with RTC and one SERCOM running, current drops below 100 uA. For battery-powered designs, gate peripherals via the Event System and use the SleepWalking controller to keep the CPU clocked off until a peripheral interrupt wakes it.
Do not connect 5 V signals to any I/O pin; the absolute maximum on PAxx is VDDIO + 0.3 V (typically 3.6 V). For UART bridging to a 5 V host, use a level shifter such as the TXS0108E. Also, when using the USB controller, VBUS sensing requires an external divider to a 5 V tolerant pin - do not connect VBUS directly to PAxx without this divider. Finally, ensure the RESET pin is pulled up via 10 kohm and decoupled with a 1 nF capacitor for clean startup.
合规信息
RoHS compliant per DigiKey product listing. Not AEC-Q100 qualified; not designed for automotive use. Halogen-free status not explicitly stated in source data. Lead-free packaging standard for tape-and-reel QFN.
