C8051F061 - 25MHz Mixed-Signal MCU | Silicon Labs
料号： C8051F061 ✓ 量产中C8051F061 概述
A mixed-signal microcontroller is an embedded semiconductor that integrates digital processing with analog conversion and comparison functions. The C8051F061 belongs to the C8051F06x family and combines an 8051-compatible embedded processing core with on-chip ADC, DAC, comparator, timer, serial-interface, and communication resources. This mixed-signal MCU category reduces the need for separate analog and digital ICs when a product must measure, generate, or monitor analog signals.
Key features include 64 KB of in-system-programmable flash, 4.25K x 8 RAM, five timers, a watchdog timer, and the Programmable Counter Array. Communication and peripheral resources include SPI, SMBus, I2C, two UARTs, and CAN 2.0B. The analog subsystem includes a 16-bit, one-channel ADC operating at 1 Msps, an eight-channel 10-bit ADC, a 12-bit, two-channel DAC, and three analog comparators. An on-chip temperature sensor is also listed for the device.
The 25 MHz implementation delivers up to 25 MIPS while retaining the established 8051 instruction set and mixed-signal integration characteristic of the C8051F06x family. The 24 available digital I/O lines make the device appropriate for compact embedded controllers that need several serial interfaces and analog measurements without relying on a large external component count. The 64-pin TQFP package exposes the mixed-signal resources and digital interfaces on a surface-mount footprint.
Typical uses include industrial sensor acquisition, process-control equipment, CAN-connected embedded instrumentation, data acquisition modules, and compact control panels. In these systems, the ADC can sample analog inputs, the DAC can generate reference or control voltages, and the UART, SPI, I2C, SMBus, and CAN interfaces can connect local sensors, actuators, and supervisory electronics. The integrated temperature sensor can also support local thermal monitoring where its accuracy is appropriate for the application.
Designers should treat the 2.7 V to 3.6 V supply range as a hard design constraint and provide decoupling close to the device pins. Analog and digital grounds, analog inputs, and high-impedance nodes require careful layout to limit noise and offset errors. Firmware migration should also verify peripheral availability and pin multiplexing for the selected C8051F06x variant rather than assuming that every family member has identical resources.
This page combines verified distributor specifications, availability information, same-family drop-in candidates, package details, and practical design guidance. It adds engineering-focused comparisons that are not normally presented together on a distributor product page, helping designers evaluate the C8051F061 for embedded control, analog measurement, and communication applications.
直接替换替代料： C8051F061 ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： C8051F061 （相同外形与封装尺寸） ——差异在于 Package, ADC Resolution, DAC Resolution, Microcontroller Type, ADC Channel Count.
C8051F063
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →C8051F065
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →C8051F067
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
C8051F061 最大额定值与电气特性
| Microcontroller Type | 8-bit mixed-signal microcontroller |
| 最大时钟频率 | 25 MHz |
| Peak Throughput | 25 MIPS |
| Program Memory | 64 KB flash |
| RAM Size | 4.25K x 8 bits |
| Digital I/O Lines | 24 lines |
| Primary ADC | 16-bit, 1-channel, 1 Msps |
| Secondary ADC | 10-bit, 8-channel |
| DAC | 12-bit, 2-channel |
| Analog Comparators | 3 |
| Timers | 5 |
| Serial Interfaces | SPI, SMBus, I2C, 2 UARTs, CAN 2.0B |
| Peripheral Support | Watchdog timer, Programmable Counter Array, on-chip temperature sensor |
| Supply Voltage Range | 2.7 V to 3.6 V |
| 封装 | 64-TQFP (10 x 10 mm) |
| 安装类型 | Surface mount |
C8051F061 64-tqfp (10 x 10 mm) 引脚配置指南
C8051F061（64-tqfp (10 x 10 mm) 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： C8051F061.
请参阅 数据手册 以查看完整引脚配置。
典型应用
C8051F061 适用于 6 应用s: Industrial Sensor Acquisition, CAN-Connected Process Control, Data Acquisition Module, Local Temperature Monitoring, Automated Test Equipment, Embedded Communication Controller.
Industrial Sensor Acquisition
The C8051F061 fits industrial sensor-acquisition equipment because it combines a 25 MIPS 8051 core with a 16-bit, one-channel, 1 Msps ADC and an eight-channel 10-bit ADC in one 64-TQFP device. The higher-resolution channel can be used for precision measurements, while the multichannel 10-bit converter can monitor several slower sensor inputs. Two UARTs, SPI, I2C, and SMBus provide local connections to sensors and service interfaces without requiring separate interface ICs. The principal design consideration is keeping analog routing away from switching and digital return currents.
推荐
CAN-Connected Process Control
The C8051F061 is suitable for compact process-control modules because it combines CAN 2.0B, two UARTs, five timers, and analog measurement resources in one 2.7 V to 3.6 V device. A controller can use the 16-bit ADC for a critical process variable, the 12-bit two-channel DAC for actuator or reference outputs, and the comparators for fast threshold detection. Its 64 KB of flash and 4.25K x 8 RAM support local control logic and communications buffering. Firmware should confirm CAN timing, interrupt requirements, and peripheral multiplexing against the device documentation.
推荐
Data Acquisition Module
The C8051F061 can serve as the core of a compact data-acquisition module where analog input count, output generation, and communications must share a small package. Its 16-bit, one-channel, 1 Msps ADC supports high-resolution waveform or sensor capture, while the eight-channel 10-bit ADC supports multichannel monitoring. The 12-bit, two-channel DAC can generate excitation or calibration signals, and SPI, I2C, SMBus, UART, and CAN allow the module to transfer data to a host. Layout must preserve analog grounding and provide local supply decoupling.
推荐
Local Temperature Monitoring
The C8051F061's integrated temperature sensor makes it useful for local thermal supervision in embedded instruments and industrial controllers. The sensor can complement the 16-bit or 10-bit ADCs used for external analog channels, while three comparators support threshold-based monitoring and five timers provide periodic measurement intervals. The MCU can report temperature through a selected UART, SPI, I2C, SMBus, or CAN connection. Because on-chip temperature readings can be influenced by package dissipation and PCB thermal paths, calibration and a representative thermal test are necessary before using them for safety-critical decisions.
推荐
Automated Test Equipment
The C8051F061 is well matched to automated test equipment that must measure analog signals and coordinate several digital interfaces. The 16-bit, one-channel, 1 Msps ADC provides a high-resolution measurement path, the 12-bit, two-channel DAC can create test stimuli, and the three comparators can perform limit detection. Five timers and the Programmable Counter Array support timing-intensive routines, while UART and CAN provide results reporting and fixture control. The 64-TQFP footprint is useful for higher-pin-count mixed-signal designs, although analog calibration and reference design review remain essential.
推荐
Embedded Communication Controller
The C8051F061 supports embedded communication-controller designs that need more than one wired interface. Two UARTs can serve console or peripheral links, SPI can support a higher-speed local bus, and I2C and SMBus can connect sensors and configuration devices. CAN 2.0B adds a standardized option for industrial networking, while the watchdog timer supports recovery from unexpected firmware or peripheral faults. Its 25 MHz 8051 core and 64 KB flash provide adequate resources for protocol handling, although timing-critical designs should verify clock accuracy, interrupt latency, and bus capacitance.
推荐
推荐产品汇总
工程参考数据： C8051F061 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | C8051F063 | C8051F065 | C8051F067 | C8051F064 | C8051F062 |
|---|---|---|---|---|---|---|
| Package | 64-TQFP (10 x 10 mm) | 64-TQFP (10 x 10 mm) - same | 64-TQFP (10 x 10 mm) - same | 64-TQFP (10 x 10 mm) - same | 64-TQFP (10 x 10 mm) - same | 64-TQFP (10 x 10 mm) - same |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Digital I/O Lines | 24 lines | 24 lines | 24 lines | 24 lines | 59 lines, 35 lines more | 59 lines, 35 lines more |
| Maximum Clock Frequency | 25 MHz | 25 MHz | 25 MHz | 25 MHz | 25 MHz | 25 MHz |
关键差异点
- Higher-resolution primary ADC combined with a multichannel auxiliary ADC （对比 C8051F060)
- Two-channel 12-bit DAC output （对比 C8051F062)
- Broader wired-communication integration （对比 C8051F064)
- Compact mixed-signal integration in 64-TQFP （对比 C8051F065)
设计说明
Place input, output, and analog-reference decoupling capacitors close to their associated C8051F061 pins, with the shortest possible ground-return paths. The verified operating range is 2.7 V to 3.6 V, so a stable 3.3 V rail is the normal design target. Keep switching-current loops away from the 16-bit and 10-bit ADC inputs, and route analog grounds according to the manufacturer's mixed-signal layout guidance rather than using an arbitrary split-plane arrangement.
Do not substitute a generic 64-pin pinout for the published C8051F061 assignment. Verify analog inputs, comparator pins, oscillator connections, programming pins, reset behavior, and alternate digital functions in the Silicon Laboratories C8051F06x datasheet. The supplied search data confirms the 64-TQFP package and 24 available digital I/O lines but does not provide the complete numbered pin table, so schematic and PCB design must be checked against the official package-specific pinout.
Avoid assuming that adjacent C8051F06x MPNs are firmware- and pin-compatible without checking their variant tables. The family includes 24-I/O and 59-I/O groups, and differences in ADC, DAC, comparator, temperature-sensor, or communications resources can change both board routing and driver code. Treat same-package family members as candidates rather than automatic replacements, then review startup code, SFR addresses, peripheral availability, and interrupt-vector assignments.
合规信息
The supplied verified snippets mention RoHS and REACH only in a generic third-party comparison context and do not provide extractable compliance declarations for C8051F061. Compliance fields are therefore recorded as unknown rather than inferred.
