CS8406-IZ - 192 kHz Digital Audio Transmitter | Cirrus Logic
料号: CS8406-IZ ✓ 量产中CS8406-IZ 概述
A digital audio transmitter is an interface IC that converts source audio and associated digital information into a standardized serial digital-audio signal. It belongs to the digital audio transmitter category within interface ICs and audio codecs. Its primary role is to provide a standards-compatible output stage for equipment that distributes digital audio between professional, consumer, and automotive audio systems.
The CS8406-IZ supports digital audio operation up to 192 kHz and provides one transmitter channel. Its CMOS implementation combines the audio input, digital-data multiplexing, standard-compliant encoding, and output-driver functions in a single monolithic device. According to the manufacturer datasheet, the supported outputs include AES3, IEC60958, S/PDIF, and EIAJ CP1201 formats, allowing the same transmitter to serve multiple digital-audio ecosystems.
The verified device information identifies a 3.14 V to 5.25 V operating supply range and an industrial temperature range from -40°C to +85°C. It is offered in a 4.40 mm TSSOP-28 surface-mount package with 28 terminals. These characteristics support compact consumer-electronics and industrial audio equipment where a standardized digital-audio output is required without allocating a separate transmitter circuit for each supported protocol.
Typical uses include S/PDIF and AES3 digital-audio outputs in consumer receivers, professional audio interfaces, broadcast and studio equipment, home-theater products, automotive head-unit electronics, and digital recording systems. In these systems, the IC converts parallel or serial source information into a cable-compatible digital stream while preserving channel, validity, and user-bit handling defined by the applicable transmission standard.
Designers should verify the complete pin assignment, supported clocking configuration, output architecture, and external component requirements in the manufacturer datasheet before layout. The 28-pin TSSOP-28 footprint should be treated as the mechanical baseline, and supply decoupling and output routing should follow the datasheet's recommended application circuit to avoid signal-integrity problems.
This page consolidates the verified CS8406-IZ electrical, environmental, packaging, protocol, purchasing, and replacement information. It also distinguishes documented same-package family options from unsupported cross-package substitutes and provides practical implementation guidance beyond a distributor listing.
直接替换替代料: CS8406-IZ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: CS8406-IZ (相同外形与封装尺寸) ——差异在于 Output Function, Package.
CS8406-CZ
✅ 直接替换📋 参考替代料(不在目录中)
CS8406-CSZ
✅ 直接替换联系询价
查看数据手册 →CS8406-IZ 最大额定值与电气特性
| Product Type | Digital audio interface transmitter |
| Manufacturer | Cirrus Logic |
| Maximum Sampling Rate | 192 kHz |
| Channel Count | 1 channel |
| Technology | Monolithic CMOS |
| Supported Standard | AES3 |
| Supported Standard | IEC60958 |
| Supported Standard | S/PDIF |
| Supported Standard | EIAJ CP1201 |
| 工作电源电压 | 3.14 V to 5.25 V |
| 工作温度 | -40°C to +85°C |
| Terminal Count | 28 terminals |
| 封装 | TSSOP-28, 4.40 mm |
| 安装类型 | Surface mount |
| Temperature Grade | Industrial |
| Output Function | Cable-driven digital audio transmission |
CS8406-IZ tssop-28, 4.40 mm 引脚配置指南
CS8406-IZ(tssop-28, 4.40 mm 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: CS8406-IZ.
请参阅 数据手册 以查看完整引脚配置。
典型应用
CS8406-IZ 适用于 6 应用s: S/PDIF Consumer Audio Outputs, AES3 Professional Audio Interfaces, Broadcast and Studio Monitoring, Home Theater and AV Equipment, Digital Audio Recorders and Converters, Automotive Digital Audio Head Units.
S/PDIF Consumer Audio Outputs
The CS8406-IZ fits consumer equipment that must generate a standardized S/PDIF digital-audio output because the manufacturer identifies S/PDIF support, one transmitter channel, and operation up to 192 kHz. Place the transmitter between the product's audio-data source and its digital output connector, using the clock, validity, user-bit, and output connections prescribed by the datasheet. Its 3.14 V to 5.25 V supply range supports conventional 5 V-class systems, although exact connector interface and output components must follow the reference circuit.
推荐
AES3 Professional Audio Interfaces
The CS8406-IZ is appropriate for professional audio interfaces requiring an AES3-compatible digital output because AES3 is one of the four standards named in the manufacturer datasheet. The device accepts audio and digital information, performs the required multiplexing and encoding, and provides a cable-oriented transmitter output at rates up to 192 kHz. Its single-channel architecture fits one-channel digital links. Clock source, data alignment, channel status, and output impedance remain design-specific and should be implemented using the complete manufacturer application guidance.
推荐
Broadcast and Studio Monitoring
The CS8406-IZ can provide a digital audio transmission function in broadcast or studio monitoring equipment that accepts AES3, IEC60958, S/PDIF, or EIAJ CP1201 data. Its maximum 192 kHz sampling rate allows use in high-resolution digital-audio paths, while the 28-pin TSSOP-28 package supports compact board layouts. The component is intended to encode and drive the digital stream, not to perform analog-to-digital conversion, so upstream converters and the system clock remain essential. Verify jitter, clocking, and output topology in the manufacturer documentation.
推荐
Home Theater and AV Equipment
The CS8406-IZ suits home-theater receivers, amplifiers, and audiovisual processors requiring a standards-compatible digital-audio transmitter rather than an analog output stage. One of the major advantages is protocol coverage: AES3, IEC60958, S/PDIF, and EIAJ CP1201 are all identified in the manufacturer datasheet, so one transmitter can support several digital-audio ecosystems. The 3.14 V to 5.25 V operating range fits conventional embedded supply plans, while the 28-pin TSSOP-28 package supports compact consumer electronics.
推荐
Digital Audio Recorders and Converters
The CS8406-IZ can serve as the digital transmission element in recorders, converters, and digital audio accessories that must pass standardized digital-audio information to downstream equipment. Its one-channel transmitter topology and 192 kHz maximum rate align with single-channel digital links used in professional conversion paths. The monolithic CMOS implementation combines multiplexing, encoding, and output drive, reducing the need for separate protocol-specific transmitter circuits. Designers must still confirm the supported source-data format and implement the manufacturer's prescribed clock and connection network.
推荐
Automotive Digital Audio Head Units
The CS8406-IZ is a candidate for automotive digital-audio head-unit electronics because its verified -40°C to +85°C operating range is suited to industrial-temperature environments. It can generate a digital transmission according to AES3, IEC60958, S/PDIF, or EIAJ CP1201, depending on the selected system format and configuration. The 28-pin TSSOP-28 package is compact and surface mountable. Before design release, verify automotive qualification, transient protection, grounding, and output-routing requirements that are not confirmed by the supplied data.
推荐
工程参考数据: CS8406-IZ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | CS8406-CZ | CS8406-CSZ |
|---|---|---|---|
| Brand | Cirrus Logic | Cirrus Logic | Cirrus Logic |
| Package | TSSOP-28 | TSSOP-28 | TSSOP-28 |
| Terminal Count | 28 terminals | 28 terminals | 28 terminals |
| Product Function | Digital audio interface transmitter | Digital audio interface transmitter | Digital audio interface transmitter |
关键差异点
- Verified industrial temperature operation (对比 CS8406-CZ)
- Explicit supply-voltage coverage (对比 CS8406-CSZ)
- Broad standard support in one transmitter (对比 CS8406-CZ)
设计说明
Use the manufacturer datasheet pin table and reference layout as the authority for the 28-terminal TSSOP-28 footprint. Keep clock, serial-data, and power-connection routing short, maintain a continuous ground reference beneath the device where the recommended layout permits, and place decoupling components close to their designated terminals. Because the exact pin names were not present in the supplied source, do not infer terminal assignments from family diagrams.
Treat the digital-audio output path as a controlled interface rather than a general-purpose logic output. Follow the manufacturer requirements for clock source, data timing, transmission format, and output connection components. If the target system uses S/PDIF, AES3, IEC60958, or EIAJ CP1201, verify that the selected operating mode and system clock satisfy the corresponding standard; the documented 192 kHz capability alone does not guarantee signal-integrity compliance.
Design the supply rail within the verified 3.14 V to 5.25 V range and account for tolerance, ripple, and sequencing at system startup. Place the manufacturer's recommended bypass capacitors adjacent to the supply and ground terminals, and keep sensitive digital-audio routing away from noisy switching nodes. Exact capacitor values, output-driver supply requirements, and maximum current were not supplied, so they must be taken from the manufacturer datasheet rather than estimated.
Do not treat equal package dimensions as proof of a drop-in replacement. CS8406-CZ and CS8406-CSZ are documented same-package family candidates, but pin naming, operating mode, temperature grade, clocking, and output configuration still require comparison. Also avoid assuming that S/PDIF, AES3, IEC60958, and EIAJ CP1201 are interchangeable without checking the source-data format and system-level timing requirements.
合规信息
The supplied web results do not provide explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations for the CS8406-IZ. AEC-Q100 status is marked not applicable because the component is an audio interface IC rather than an automotive-qualified power device, and no automotive qualification claim was supplied.