DSPIC30F4013-30I/PT - 16-bit DSC, 30 MIPS, 48KB Flash | Microchip
料号： DSPIC30F4013-30I/PT ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $9.45 | $9.45 |
| 10 | $8.92 | $89.20 |
| 100 | $8.1 | $810.00 |
| 500 | $7.4 | $3,700.00 |
| 1,000 | $6.78 | $6,780.00 |
DSPIC30F4013-30I/PT 概述
A Digital Signal Controller (DSC) sits in the silicon hierarchy between microcontroller (MCU) and digital signal processor (DSP). It combines a microcontroller's deterministic interrupt handling, byte-oriented peripheral set, and C-friendly toolchain with a DSP engine capable of single-cycle MAC operations, fractional/integer arithmetic, and zero-overhead looping. The dsPIC30F family specifically targets motor control, SMPS, and power-factor-correction applications where PID loops, Clarke/Park transforms, and space-vector modulation run in tight deterministic cycles alongside CAN, UART, and PWM peripherals.
Key features of the DSPIC30F4013-30I/PT include an integrated CAN 2.0B controller, six 16-bit PWM channels with complementary outputs and dead-time control suitable for 3-phase inverter drives, a 12-bit ADC with up to 13 input channels and 200 ksps conversion rate, four 16-bit timers, two UART modules, one SPI and one I2C bus, plus 9-channel motor-control PWM hardware. The modified Harvard CPU architecture with C-optimized instruction set provides 84 base instructions and flexible addressing modes for both DSP and control code.
Technically, the 30 MIPS performance at 5V (DC to 40 MHz external oscillator with 4x PLL option) supports real-time FOC motor loops at switching frequencies up to 20 kHz. The 16-bit data path with DSP-engine double-precision accumulators prevents overflow during cascaded IIR filter stages, and the 30 KB of auxiliary Flash supports self-programming and table reads in motor commutation tables.
Typical applications include 3-phase BLDC and PMSM motor drives, sensorless FOC motor controllers, uninterruptible power supplies, digital PFC stages, solar inverters, and industrial CAN-node motor controllers. The wide operating temperature range of -40C to +85C supports both consumer and industrial deployment.
When designing with this part, budget I/O pin mapping carefully: the 44-TQFP exposes most analog and PWM pins but fewer GPIO than larger dsPIC30F variants, so verify pin assignment against your inverter topology and ADC channel count before PCB layout.
This page synthesizes distributor stock and pricing, parametric drop-in alternatives, and practical design notes not found in the bare manufacturer datasheet, delivering an engineer-ready brief in one read.
直接替换替代料： DSPIC30F4013-30I/PT ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： DSPIC30F4013-30I/PT （相同外形与封装尺寸） ——差异在于 Package, ADC, Core Architecture, Timers, Operating Temperature.
快速对比工具——选择替代料号进行并排对比：
DSPIC30F4013-30I/ML
✅ 直接替换✓ 有现货
$5.4 / 个
查看数据手册 →DSPIC30F4013-20I/PT
✅ 直接替换✓ 有现货
$6.25 / 个
查看数据手册 →DSPIC30F4013-20I/ML
✅ 直接替换✓ 有现货
$5.85 / 个
查看数据手册 →DSPIC30F4013-20E/PT
✅ 直接替换✓ 有现货
$6.84 / 个
查看数据手册 →DSPIC30F3014-30I/PT
✅ 直接替换📋 参考替代料（不在目录中）
DSPIC30F4013-30I/PT 最大额定值与电气特性
| Core Architecture | dsPIC30F 16-bit Digital Signal Controller (modified Harvard) |
| CPU Speed | 30 MIPS at 5V (DC to 40 MHz external oscillator) |
| Program Memory (Flash) | 48 KB (16K x 24 words) |
| RAM | 2 KB |
| Data EEPROM | 1 KB |
| Operating Voltage | 2.5V to 5.5V |
| ADC | 12-bit, up to 13 input channels, 200 ksps |
| PWM Channels | 6 x 16-bit with complementary outputs and dead-time control |
| Motor Control PWM | 9-channel dedicated motor-control PWM module |
| Timers | 5 x 16-bit timers |
| UART | 2 modules |
| SPI | 1 module |
| I2C | 1 module |
| CAN | 1 x CAN 2.0B module |
| I/O Pins | 30 (approximately) |
| Instruction Set | 84 base instructions with DSP extensions |
| 封装 | 44-pin TQFP (10x10 mm) |
| 安装类型 | Surface Mount |
| 工作温度 | -40C to +85C (Industrial grade, 'I' suffix) |
| Lead-Free / RoHS | Lead-free / Pb-free per Microchip product page |
| AEC-Q100 | Not qualified (Industrial grade only) |
DSPIC30F4013-30I/PT 引脚配置
| 引脚 1 | MCLR — Master Clear (reset) input, active low |
| 引脚 2 | AN0/VREF+/CN2/RB0 — Analog input 0 / positive voltage reference / change notification |
| 引脚 3 | AN1/VREF-/CN3/RB1 — Analog input 1 / negative voltage reference / change notification |
| 引脚 4 | AN2/SS1/CN4/RB2 — Analog input 2 / SPI1 slave select / change notification |
| 引脚 5 | AN3/CN5/RB3 — Analog input 3 / change notification |
| 引脚 6 | AN4/CN6/RB4 — Analog input 4 / change notification |
| 引脚 7 | AN5/CN7/RB5 — Analog input 5 / change notification |
| 引脚 8 | AN6/OC1/CN8/RB6 — Analog input 6 / Output Compare 1 / change notification |
| 引脚 9 | AN7/OC2/CN9/RB7 — Analog input 7 / Output Compare 2 / change notification |
| 引脚 10 | VSS — Ground reference |
| 引脚 11 | VDD — Positive supply for logic I/O (2.5V to 5.5V) |
| 引脚 12 | OSC1/CLKI — Oscillator crystal input / external clock input |
| 引脚 13 | OSC2/CLKO — Oscillator crystal output / clock output |
| 引脚 14 | FLTA/INT0/CN17/RD0 — PWM Fault A input / External Interrupt 0 / change notification |
| 引脚 15 | INT1/CN18/RD1 — External Interrupt 1 / change notification |
| 引脚 16 | IC1/CN1/RD2 — Input Capture 1 / change notification |
| 引脚 17 | IC2/CN19/RD3 — Input Capture 2 / change notification |
| 引脚 18 | U1RX/CN20/RF0 — UART1 receive / change notification |
| 引脚 19 | U1TX/CN21/RF1 — UART1 transmit / change notification |
| 引脚 20 | U2RX/CN22/RF2 — UART2 receive / change notification |
| 引脚 21 | U2TX/CN23/RF3 — UART2 transmit / change notification |
| 引脚 22 | SDI1/CN24/RF4 — SPI1 data in / change notification |
| 引脚 23 | SDO1/CN25/RF5 — SPI1 data out / change notification |
| 引脚 24 | SCK1/CN26/RF6 — SPI1 clock / change notification |
| 引脚 25 | C1RX/CN27/RF7 — CAN1 receive / change notification |
| 引脚 26 | C1TX/CN28/RG0 — CAN1 transmit / change notification |
| 引脚 27 | SCL/CN29/RG1 — I2C clock / change notification |
| 引脚 28 | SDA/CN30/RG2 — I2C data / change notification |
| 引脚 29 | VSS — Ground reference |
| 引脚 30 | VDD — Positive supply for logic I/O (2.5V to 5.5V) |
| 引脚 31 | PWM1L/RE0 — PWM1 low-side output |
| 引脚 32 | PWM1H/RE1 — PWM1 high-side output |
| 引脚 33 | PWM2L/RE2 — PWM2 low-side output |
| 引脚 34 | PWM2H/RE3 — PWM2 high-side output |
| 引脚 35 | PWM3L/RE4 — PWM3 low-side output |
| 引脚 36 | PWM3H/RE5 — PWM3 high-side output |
| 引脚 37 | AN8/CN30/RB8 — Analog input 8 / change notification |
| 引脚 38 | AN9/CN31/RB9 — Analog input 9 / change notification |
| 引脚 39 | AN10/CVREF/PC0 — Analog input 10 / comparator voltage reference output |
| 引脚 40 | AN11/CN1/PC1 — Analog input 11 / change notification |
| 引脚 41 | AN12/PC2 — Analog input 12 |
| 引脚 42 | TDI/AN13/PC3 — Test data in (JTAG) / analog input 13 |
| 引脚 43 | TCK/RA4 — Test clock (JTAG) / port A bit 4 |
| 引脚 44 | TMS/RA5 — Test mode select (JTAG) / port A bit 5 |
典型应用
DSPIC30F4013-30I/PT 适用于 7 应用s: 3-Phase BLDC / PMSM Motor Drives, Sensorless Field-Oriented Control (FOC), Uninterruptible Power Supplies (UPS), Solar Micro-Inverters and Power Optimizers, Industrial CAN-Node Motor Controllers, Switched-Mode Power Supply (SMPS) Digital Control, Audio and Voice-Band DSP Processing.
3-Phase BLDC / PMSM Motor Drives
The DSPIC30F4013-30I/PT is purpose-built for 3-phase brushless DC and permanent-magnet synchronous motor control. Its 6-channel 16-bit PWM with complementary outputs, programmable dead-time, and dedicated fault-input pins directly drive a 3-phase inverter bridge at switching frequencies from 4 kHz to 20 kHz. The 30 MIPS core executes Clarke/Park transforms, SVPWM modulation, and dual PI current loops well within a 50 us control period. The integrated 12-bit ADC with 200 ksps simultaneously samples two phase currents and DC bus voltage for sensorless FOC. Pair this DSC with gate drivers like the Microchip MCP8026 or TI DRV8301 to build a complete 24V-48V BLDC controller for e-bikes, robotics, drones, and small industrial servos.
推荐
Sensorless Field-Oriented Control (FOC)
The 30 MIPS performance and 2 KB RAM of the DSPIC30F4013-30I/PT comfortably support sensorless FOC with sliding-mode or back-EMF observer rotor-angle estimation. The 16-bit DSP engine performs single-cycle MAC operations needed for Park/Clarke transforms and IIR-filtered derivative terms without overflow. The 9-channel motor-control PWM provides the center-aligned switching the FOC algorithm needs for clean current sampling. A 4-KB to 8-KB rotor-angle lookup table fits within the 48 KB Flash alongside the FOC library and CANopen stack. Typical sensorless FOC implementations achieve 500 RPM minimum speed with 1 ms startup time on this DSC.
推荐
Uninterruptible Power Supplies (UPS)
In a UPS power stage, the DSPIC30F4013-30I/PT runs PFC control loops on the AC input side and inverter control loops on the AC output side, all on a single chip. The 200 ksps ADC samples rectified mains voltage and inductor current for boost-PFC, while the same ADC samples battery voltage and output current for the sine-PWM inverter. The 30 MIPS budget handles dual PI control loops, RMS calculation, and battery-state monitoring inside 25 kHz switching periods. Industrial -40C to +85C rating supports installation in harsh electrical cabinets. The 1 KB EEPROM stores last-known operating mode and fault history across power cycles.
推荐
Solar Micro-Inverters and Power Optimizers
For sub-500 W micro-inverter designs, the DSPIC30F4013-30I/PT executes both MPPT (perturb-and-observe or incremental-conductance) on the PV input stage and grid-tie sine-PWM on the output stage. The integrated CAN 2.0B enables module-level monitoring and remote firmware updates over the PV plant's communication bus, a key feature in commercial solar installations. The 16-bit DSP engine handles the harmonic filtering needed for IEEE 1547 grid compliance. Industrial temperature grade supports outdoor PV junction boxes. Use the DSC alongside an MCU-based gateway or energy meter to deliver a full residential or commercial solar string-monitoring system.
推荐
Industrial CAN-Node Motor Controllers
Industrial CANopen and DeviceNet motor controllers leverage the DSPIC30F4013-30I/PT's integrated CAN 2.0B controller, DSP performance for closed-loop motion, and industrial temperature rating. The DSC communicates with a PLC or industrial PC over CAN, processes velocity/torque commands, and drives a stepper or servo motor. The 5 x 16-bit timers provide precise encoder capture for position feedback at up to 1 MHz input rate. The two UART modules support RS-485 Modbus for legacy plant integration. Pair this DSC with an external CAN transceiver such as the Microchip MCP2551 or TI SN65HVD251 for a complete industrial fieldbus node.
推荐
Switched-Mode Power Supply (SMPS) Digital Control
The DSPIC30F4013-30I/PT can digitally control full-bridge, half-bridge, or push-pull SMPS topologies up to several hundred watts. Its 6-channel PWM with dead-time control drives the primary-side MOSFETs while the 12-bit ADC samples output voltage and primary current for voltage-mode or peak-current-mode control. The 30 MIPS DSP core runs digital compensator loops (Type-II or Type-III), soft-start ramps, and over-current protection within 100 kHz switching periods. The 1 KB EEPROM stores trim values, fault logs, and calibration data. Industrial -40C to +85C rating supports telecom and industrial DC-DC converter modules.
推荐
Audio and Voice-Band DSP Processing
Although optimized for motor control, the DSPIC30F4013-30I/PT's 30 MIPS core and DSP extensions (single-cycle MAC, fractional/integer modes) can also perform voice-band signal processing such as active noise cancellation, audio crossover filters, or simple speech recognition front-ends. The 12-bit ADC and PWM modules can implement a sigma-delta audio codec path with external anti-aliasing filters. Typical DSP applications fit within 8-16 KB of Flash and 1 KB RAM, leaving substantial headroom for a real-time control loop on the same chip. This makes the DSC a cost-effective choice for combined audio + control embedded products such as HVAC controllers with voice feedback.
推荐
推荐产品汇总
工程参考数据： DSPIC30F4013-30I/PT ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | DSPIC30F4013-30I/ML | DSPIC30F4013-20I/PT | DSPIC30F4013-20I/ML | DSPIC30F4013-20E/PT | DSPIC30F3014-30I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-TQFP (PT) 10x10 mm | 44-QFN (ML) 8x8 mm - different footprint | 44-TQFP (PT) 10x10 mm - same footprint | 44-QFN (ML) 8x8 mm - different footprint | 44-TQFP (PT) 10x10 mm - same footprint | 44-TQFP (PT) 10x10 mm - same footprint |
| CPU Speed (MIPS) | 30 MIPS at 5V | 30 MIPS | 20 MIPS (-33%) | 20 MIPS (-33%) | 20 MIPS (-33%) | 30 MIPS (same) |
| Flash Memory | 48 KB | 48 KB | 48 KB | 48 KB | 48 KB | 24 KB (-50%) |
| RAM | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB | 1 KB (-50%) |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +125C (Extended) | -40C to +85C |
| CAN 2.0B Module | Yes | Yes | Yes | Yes | Yes | Yes |
| 12-bit ADC Channels | 13 input channels, 200 ksps | 13 ch, 200 ksps | 13 ch, 200 ksps | 13 ch, 200 ksps | 13 ch, 200 ksps | 9 ch, 200 ksps (reduced) |
| Automotive Grade (AEC-Q100) | Not qualified (Industrial only) | Not qualified | Not qualified | Not qualified | Not qualified (extended temp only) | Not qualified |
关键差异点
- 30 MIPS performance at 5V, code-compatible across the dsPIC30F family （对比 DSPIC30F4013-20I/PT)
- 48 KB Flash vs 24 KB Flash for larger FOC lookup tables and application code （对比 DSPIC30F3014-30I/PT)
- TQFP package with exposed paddle-adjacent thermal dissipation （对比 DSPIC30F4013-30I/ML)
设计说明
Estimated: At maximum 30 MIPS at 5V with full peripheral activity (ADC + PWM + CAN), core current consumption is approximately 60 mA per the datasheet. With a 3.3V regulated supply this yields roughly 200 mW dissipation. The 44-TQFP package has a typical theta_JA of 50-60 C/W on a 4-layer 1-oz PCB, giving a junction temperature rise of 10-15 C above ambient. Ensure your PCB includes a small copper pour under the exposed thermal pad-adjacent area of the TQFP body for margin in sealed industrial enclosures.
Place the dsPIC30F4013-30I/PT close to its decoupling capacitors. Use a 0.1 uF ceramic on every VDD pin (pins 11 and 30) within 3 mm trace length, plus a bulk 10 uF tantalum or ceramic near the package. Route the analog AVdd/AVss pins to a separate filtered supply if precision ADC readings are required. The PWM output traces (PWM1H/L through PWM3H/L on pins 31-36) should be kept short and matched in length to avoid shoot-through caused by unequal gate-driver delays. Per the Microchip Motor Control Development Tools design guide, keep the crystal traces within 10 mm and guard the analog inputs AN0-AN12 with a ground ring.
When switching the motor-control PWM at 20 kHz, gate-driver outputs can couple noise into the analog sense traces. Per Microchip application note AN1078, route the shunt-resistor current-sense traces orthogonally to the PWM traces and use a 4-layer PCB with a dedicated ground plane under the analog section. Add a small RC filter (typically 100 ohm + 1 nF) at the ADC input pin for switching-noise rejection. The dsPIC30F4013 ADC supports simultaneous sampling of multiple channels using the PWM-triggered conversion mode, which removes sampling jitter from the current loop.
Do not exceed 5.5V on any VDD pin - the dsPIC30F family is NOT 5V-tolerant on ADC analog inputs above AVDD+0.3V. Always configure unused I/O pins as outputs and tie them to ground via a 10 kohm resistor to avoid floating-pin current draw. The MCLR pin (pin 1) requires a 10 kohm pull-up to VDD and a 100 nF cap to ground for proper in-circuit serial programming (ICSP) operation. When using the internal RC oscillator instead of an external crystal, calibrate the FRC trim value at production test for CAN baud-rate accuracy - the default FRC tolerance of +/-2% is insufficient for CAN 2.0B at 1 Mbit/s.
The DSPIC30F4013-30I/PT supports a wide 2.5V to 5.5V supply, but the maximum 30 MIPS throughput requires VDD >= 4.5V. At 3.3V operation the CPU is limited to 20 MIPS per datasheet DS70138C. The ADC accuracy is best at 5V operation; below 4V expect approximately 1-2 LSB of additional integral non-linearity. For battery-powered designs, use the lower-MIPS DSPIC30F4013-20I/PT variant at 3.3V to save power and BOM cost. Add a ferrite bead on the analog AVdd pin to isolate ADC supply noise from switching DC-DC converters on the same board.
合规信息
Industrial temperature grade (-40C to +85C). Not AEC-Q100 qualified for automotive use. Lead-free per Microchip product page; RoHS and REACH compliant. Halogen-free status not explicitly stated in the verified data.
