EM6151V53SO8B+ - Windowed Watchdog Supervisor, 5.3V, SOIC-8 | EM Microelectronic
料号： EM6151V53SO8B+ ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $4.88 | $4.88 |
| 10 | $3.95 | $39.50 |
| 100 | $2.78 | $278.00 |
| 500 | $2.1 | $1,050.00 |
| 1,000 | $1.75 | $1,750.00 |
EM6151V53SO8B+ 概述
A watchdog timer is a hardware peripheral that monitors microcontroller activity and triggers a reset if the firmware fails to service the watchdog within a defined window. A windowed watchdog enforces both a minimum and maximum service interval, catching firmware that resets the watchdog too quickly (indicating stuck code in a tight loop) and firmware that fails to service it at all. This is critical for automotive, industrial, and safety-critical applications where firmware lockups must be detected and recovered automatically.
Key specifications include a 5.3V factory-trimmed reset threshold voltage, 4.57ms typical reset pulse width, open-drain or open-collector active-low RESET output, and very low quiescent current suitable for battery-backed systems. The windowed watchdog function prevents faulty firmware from masking a system lockup by rapidly toggling the watchdog input. The sleep-mode feature allows the host microcontroller to disable the watchdog during low-power states.
The EM6151V53SO8B+ uses EM Microelectronic's proprietary low-power CMOS architecture, integrating a precision bandgap voltage reference, a windowed watchdog timer, and a reset generator on a single die. The factory-trimmed threshold eliminates external resistor dividers and reduces BOM cost. The integrated architecture minimizes board space compared to discrete supervisor plus external watchdog solutions.
Typical applications include embedded microcontroller supervision in industrial control, automotive body and chassis ECUs, battery-powered IoT sensor nodes, and safety-critical medical devices. The 5.3V threshold is well-matched to 5V regulated rails with tolerance headroom. The open-drain output allows wired-OR connection of multiple supervisors on a shared reset line.
When designing with this device, ensure the WDI signal from the host microcontroller toggles within the watchdog window both faster than the watchdog timeout and slower than the minimum window period. Place a 0.1uF decoupling capacitor close to VCC, and use a pull-up resistor on the open-drain RESET output sized for the line capacitance and required rise time.
This page synthesizes distributor pricing from DigiKey, LCSC, FPGACenter, JLCPCB, and Veswin, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
直接替换替代料： EM6151V53SO8B+ ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
快速对比工具——选择替代料号进行并排对比：
EM6151V45SO8B+
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
EM6151V53SO8A+
✅ 直接替换📋 参考替代料（不在目录中）
EM6151V53SO8B
✅ 直接替换📋 参考替代料（不在目录中）
EM6151V33SO8B+
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
EM6151V93SO8B+
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
EM6151V53SO8B+ 规格参数
| Manufacturer | EM Microelectronic |
| 功能 | Windowed Watchdog with Reset, Sleep Mode |
| Reset Threshold Voltage | 5.3 V (factory trimmed) |
| Reset Output Type | Open Drain or Open Collector |
| Reset Active Level | Active Low |
| Number of Supervisors | 1 |
| Reset Pulse Width (typical) | 4.57 ms |
| Watchdog Type | Windowed |
| Output Channel Count | 1 Channel |
| 封装 | 8-SOIC (3.90 mm Width) |
| 安装类型 | Surface Mount |
| RoHS 状态 | Compliant |
| Lead-Free Status | Yes |
EM6151V53SO8B+ 引脚配置
| 引脚 1 | VCC — Supply voltage input |
| 引脚 2 | WDI — Watchdog input from MCU |
| 引脚 3 | SLEEP — Sleep-mode control input |
| 引脚 4 | GND — Ground |
| 引脚 5 | RESET — Active-low open-drain reset output |
| 引脚 6 | NC — Not connected (per datasheet) |
| 引脚 7 | NC — Not connected (per datasheet) |
| 引脚 8 | NC — Not connected (per datasheet) |
典型应用
EM6151V53SO8B+ 适用于 6 应用s: Automotive Body Control Module (BCM) Watchdog, Industrial PLC and Factory Automation Controller, Battery-Powered IoT Sensor Node Sleep Manager, Medical Device Firmware Safety Monitor, Networking Equipment and Router Supervisor, Embedded Motor Drive and Servo Controller.
Automotive Body Control Module (BCM) Watchdog
The EM6151V53SO8B+ supervises the 5V MCU rail in body and chassis ECUs, catching firmware lockups in door, lighting, and wiper modules. Its 5.3V threshold aligns with 5V regulators plus tolerance margin, and the windowed watchdog enforces both minimum and maximum service intervals per ISO 26262 diagnostic coverage guidelines. Placed between the 5V LDO output and the MCU NRST pin with a 10k pull-up, the open-drain RESET asserts on brownout or stalled firmware. Compared to a discrete supervisor plus external watchdog, the EM6151 cuts BOM cost and PCB area. Use a 0.1uF decoupling cap within 5mm of VCC to suppress reset chattering during cranking transients.
推荐
Industrial PLC and Factory Automation Controller
The EM6151V53SO8B+ monitors the 5V logic rail of industrial PLCs, motor controllers, and sensor hubs, triggering a reset if the supply droops or firmware locks up. The factory-trimmed 5.3V threshold eliminates the drift and calibration overhead of resistor-divided supervisors, while the windowed watchdog prevents firmware stuck in a tight clear-WDI loop from masking a true lockup. In a typical 24V-to-5V PLC backplane, the supervisor sits downstream of the isolated 5V LDO and feeds the host MCU reset through a 10k pull-up to logic VCC. The 4.57ms reset pulse width is sufficient for slow-rising industrial power sequencing.
推荐
Battery-Powered IoT Sensor Node Sleep Manager
The EM6151V53SO8B+ provides voltage supervision and windowed watchdog for IoT sensor nodes powered from a 5V USB or battery-derived rail, with its sleep-mode input allowing the host MCU to disable the watchdog during deep-sleep current-measurement windows. During active measurement cycles, the windowed watchdog enforces firmware health; during sleep, the MCU asserts SLEEP to halt watchdog activity and minimize quiescent draw. The open-drain RESET output can wake the MCU via its NRST or interrupt line on a brownout event. Compared to a separate voltage supervisor and watchdog IC, the EM6151 reduces quiescent current by sharing a single bias block.
推荐
Medical Device Firmware Safety Monitor
The EM6151V53SO8B+ is used in non-life-sustaining medical devices such as patient monitors, infusion-pump controllers, and diagnostic analyzers to enforce firmware health on the 5V MCU rail. The windowed watchdog satisfies IEC 62304 software-safety requirements by detecting both runaway and stuck firmware, while the 5.3V threshold catches brownouts that could cause MCU register corruption. Placed adjacent to the host MCU with the open-drain RESET wired to NRST, the EM6151 forces a deterministic restart on fault. The integrated voltage-monitor-plus-watchdog design simplifies the IEC 60601-1 third-party safety review.
推荐
Networking Equipment and Router Supervisor
The EM6151V53SO8B+ supervises the 5V logic rail of network routers, switches, and PoE injectors where firmware lockups would interrupt service. The factory-trimmed 5.3V threshold aligns with 5V PoE-derived rails plus margin, and the windowed watchdog enforces firmware health on the management-MCU rail even when the main CPU is healthy. Wired-OR with other supervisors on a shared reset bus, the open-drain output allows hierarchical reset coordination. The 4.57ms reset pulse width is sufficient for the management-MCU's slow-rising internal regulator to stabilize.
推荐
Embedded Motor Drive and Servo Controller
The EM6151V53SO8B+ monitors the 5V control-MCU rail in BLDC and stepper motor drives, catching firmware faults before they cause mechanical damage. The windowed watchdog enforces servo-loop firmware health, while the 5.3V threshold catches brownouts during motor back-EMF events that could corrupt the MCU's commutation timing. Placed between the 5V logic LDO and the MCU NRST with a 1k pull-up for fast reset rise time, the EM6151 provides deterministic fault recovery. The 8-SOIC footprint integrates easily into the compact motor-drive PCB layout alongside DRV-class gate drivers.
推荐
推荐产品汇总
工程参考数据： EM6151V53SO8B+ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | EM6151V45SO8B+ | EM6151V53SO8A+ | EM6151V53SO8B | EM6151V33SO8B+ | EM6151V93SO8B+ |
|---|---|---|---|---|---|---|
| Package | 8-SOIC (3.90 mm) | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same |
| Brand | EM Microelectronic | EM Microelectronic - same | EM Microelectronic - same | EM Microelectronic - same | EM Microelectronic - same | EM Microelectronic - same |
| Reset Threshold Voltage | 5.3 V | 4.5 V | 5.3 V | 5.3 V | 3.3 V | 9.3 V |
| Reset Pulse Width | 4.57 ms | 4.57 ms (typical, family) | 4.57 ms | 4.57 ms | 4.57 ms (typical, family) | 4.57 ms (typical, family) |
| Reset Output Type | Open Drain / Open Collector, Active Low | Open Drain, Active Low | Open Drain, Active Low | Open Drain, Active Low | Open Drain, Active Low | Open Drain, Active Low |
| Watchdog Type | Windowed | Windowed | Windowed | Windowed | Windowed | Windowed |
| Sleep Mode Support | Yes | Yes | Yes | Yes | Yes | Yes |
| RoHS / Lead-Free | Yes / Yes (+ suffix) | Yes / Yes | Yes / Yes | Compliant / process variant | Yes / Yes | Yes / Yes |
关键差异点
- Windowed watchdog with sleep-mode control in a single 8-SOIC footprint （对比 Discrete voltage supervisor + external watchdog timer)
- Factory-trimmed 5.3V threshold eliminates external resistor divider （对比 Adjustable-threshold supervisor using external resistors)
- Open-drain active-low reset enables wired-OR multi-supervisor reset bus （对比 Push-pull reset supervisor)
设计说明
Place a 0.1uF decoupling capacitor within 5mm of the EM6151V53SO8B+ VCC pin, with a wide ground return to the host MCU's GND pin. The windowed watchdog and reset pulse widths are timing-critical; long VCC traces introduce inductance that can cause reset chattering during fast load transients. Keep the WDI trace short and routed away from switching-noise sources such as motor gate-drive signals to prevent watchdog false resets.
Size the RESET pull-up resistor for both rise time and current. A 10k pull-up to 5V gives ~5ms rise time into 50pF of MCU pin capacitance, which is appropriate for the 4.57ms reset pulse width. Too small a resistor (1k) wastes quiescent current; too large (100k) slows the rise and may violate the MCU's minimum reset pulse requirement. The open-drain output allows wired-OR connection of multiple supervisors, but verify the wired-OR logic level in mixed-voltage systems.
When the EM6151V53SO8B+ is used in an automotive board with cranking transients or in an industrial PLC with motor back-EMF, ensure the upstream 5V LDO has sufficient PSRR and load-step response. The supervisor triggers a reset whenever VCC drops below 5.3V, so a poorly-regulated 5V rail will generate spurious resets. Estimated: at a 5V LDO load step of 100mA with 10us rise time, the VCC droop must stay above 5.3V for at least 4.57ms to avoid triggering a reset pulse. Add bulk capacitance of at least 22uF near the MCU VCC rail to absorb transients.
合规信息
RoHS compliant and lead-free based on '+' suffix per EM Microelectronic ordering convention. AEC-Q100 status not explicitly stated in verified data - confirm with manufacturer for automotive deployments. REACH, halogen-free, and conflict-minerals compliance not found in verified data.
