EPC16QC100 - 16Mb FPGA Configuration PROM, 100-PQFP | Altera
料号： EPC16QC100 ✗ 停产| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $28.5 | $28.50 |
| 10 | $25.75 | $257.50 |
| 100 | $22.1 | $2,210.00 |
| 500 | $18.4 | $9,200.00 |
| 1,000 | $14.95 | $14,950.00 |
EPC16QC100 概述
A configuration PROM (sometimes called a configuration memory or boot PROM) is a non-volatile serial memory dedicated to storing an FPGA's bitstream. At power-up the FPGA loads its logic from the PROM over a serial or parallel configuration interface; the PROM effectively replaces a parallel flash device and a configuration controller. Within the broader hierarchy, configuration PROMs sit under memory ICs (non-volatile) -> boot/companion memory -> FPGA configuration subsystem.
Key features include 16 Mb of flash organized for Altera's enhanced configuration interface, 33 MHz maximum configuration clock, multi-device cascadable support for very large FPGA bitstreams, in-system programmability through the IEEE 1149.1 JTAG interface, and built-in compression support so larger bitstreams fit in the available flash. Compared with discrete flash plus a CPLD-based configuration controller, the EPC16QC100 integrates both functions on one die, reducing board area and BOM count.
Architecturally, the device combines a configuration controller and a flash array on a single chip, with dedicated interface pins (nSTATUS, CONF_DONE, nCONFIG, DCLK, DATA) that match Altera's older FPGA configuration scheme. It supports Stratix, APEX II, APEX 20K, Mercury, ACEX 1K, and FLEX 10K device families. Note that Altera was acquired by Intel, and this part is widely reported as obsolete or NRND — modern Altera/Intel devices use Cyclone, Arria, and Stratix families with newer configuration schemes (active serial flash).
Typical applications include legacy FPGA configuration for industrial controllers, military/aerospace systems that still use ACEX/Stratix-class FPGAs, prototyping boards, and migration designs where existing bitstreams must be preserved. Designers should verify availability before committing new designs, as the part is increasingly difficult to source.
Design considerations include routing the JTAG chain (TCK/TMS/TDO/TDI) to all devices in the chain, providing proper decoupling (0.1 µF and 10 µF), and ensuring DCLK and DATA trace lengths match Altera's guidelines. Because this part targets legacy families, confirm that the target FPGA still accepts enhanced configuration PROM mode before qualifying the design.
This page synthesizes distributor pricing, parametric alternatives, and legacy design notes that go beyond the Altera datasheet to help engineers manage end-of-life risk for legacy FPGA systems.
直接替换替代料： EPC16QC100 ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： EPC16QC100 （相同外形与封装尺寸） ——差异在于 Package, Memory Type, Operating Temperature, Configuration Interface, Memory Size.
快速对比工具——选择替代料号进行并排对比：
EPC8QC100N
✅ 直接替换✓ 有现货
$9.1 / 个
查看数据手册 →EPC16QC100N
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$24.1 / 个
查看数据手册 →EPC16QI100
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$15.4 / 个
查看数据手册 →EPC16QC-100T
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$14.5 / 个
查看数据手册 →EPC16C100T
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$16.2 / 个
查看数据手册 →EPC160C100
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$7.2 / 个
查看数据手册 →EPC16QC100 最大额定值与电气特性
| 存储器类型 | Flash Configuration PROM (non-volatile) |
| 存储容量 | 16 Mbit |
| Configuration Clock (max) | 33 MHz |
| 接口 | Altera enhanced configuration serial interface |
| In-System Programmability | Yes (IEEE 1149.1 JTAG) |
| Supply Voltage (VCC) | 3.0 V to 3.6 V |
| 工作温度 | -40C to +85C (commercial) |
| 封装 | 100-pin PQFP (20 x 14 mm) |
| 安装类型 | Surface Mount |
| Cascadable | Yes (multi-device chain) |
| Compression Support | Yes (Altera enhanced compression) |
| Supported FPGA Families | Stratix, APEX II, APEX 20K, Mercury, ACEX 1K, FLEX 10K |
| Configuration Controller | Integrated on-die |
EPC16QC100 100-pin pqfp (20 x 14 mm) 引脚配置指南
EPC16QC100（100-pin pqfp (20 x 14 mm) 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： EPC16QC100.
请参阅 数据手册 以查看完整引脚配置。
典型应用
EPC16QC100 适用于 6 应用s: Legacy Stratix FPGA Configuration, APEX II / APEX 20K Configuration Storage, ACEX 1K / FLEX 10K Boot Memory, Industrial Controller Bitstream Storage, Military / Aerospace Legacy Systems, Prototyping Boards and Lab Fixtures.
Legacy Stratix FPGA Configuration
The EPC16QC100 is the canonical boot memory for first-generation Altera Stratix FPGAs, providing 16 Mb of non-volatile storage for the configuration bitstream. At power-up the PROM serializes the bitstream to the Stratix device over DCLK/DATA, replacing an external flash + CPLD pair with one integrated IC. Compared with discrete flash, the integrated controller ensures Altera-compatible timing on CONF_DONE/nSTATUS, eliminating handshaking bugs. Designers should still terminate JTAG properly and observe Altera's DCLK signal-integrity guidelines.
推荐
APEX II / APEX 20K Configuration Storage
APEX II and APEX 20K FPGAs were designed to load from Altera enhanced configuration PROMs, and the EPC16QC100 is the high-density option that fits large APEX bitstreams. Using the EPC16QC100 keeps the BOM small and the configuration chain deterministic, which matters in industrial-control and military/aerospace systems that still deploy APEX designs. The 33 MHz DCLK keeps configuration time below one second for most APEX bitstreams, which is acceptable for systems that tolerate sub-second boot.
推荐
ACEX 1K / FLEX 10K Boot Memory
ACEX 1K and FLEX 10K devices can use the EPC16QC100 for non-volatile boot, with 16 Mb headroom for larger FLEX designs. This is helpful when migrating older FLEX 10K prototypes to a single stock-keeping part, simplifying spares inventory across product variants. Engineers often prefer the EPC16QC100 over smaller PROMs because one part covers all bitstream sizes in a multi-board family.
推荐
Industrial Controller Bitstream Storage
In industrial-control systems (PLCs, motor controllers, machine-vision processors) using legacy Altera FPGAs, the EPC16QC100 provides deterministic in-system field updates via JTAG. The 100-pin PQFP package is robust to industrial shock/vibration profiles, and the 3.3 V supply matches the legacy FPGA rail. JTAG in-system programming enables factory floor updates without removing the controller from the cabinet, reducing service cost.
推荐
Military / Aerospace Legacy Systems
Long-lifecycle aerospace and defense platforms continue to deploy ACEX 1K, APEX, and first-generation Stratix FPGAs that depend on the EPC16QC100 for configuration. Because these programs can run for 20+ years, sustaining engineering teams use the EPC16QC100 to keep fielded systems operational. Altera/Intel still supports last-time-buy windows for defense customers; plan reorders accordingly.
推荐
Prototyping Boards and Lab Fixtures
Universities, research labs, and FPGA prototype boards use the EPC16QC100 as a convenient way to load Altera reference designs without needing a PC-hosted programmer. The JTAG chain allows rapid bitstream iteration, and the 16 Mb capacity covers most academic reference designs. Engineers can also combine multiple EPC16QC100s in cascade to load several bitstream images for design-space exploration.
推荐
推荐产品汇总
工程参考数据： EPC16QC100 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | EPC8QC100N | EPC16QC100N | EPC16QI100 | EPC16QC-100T |
|---|---|---|---|---|---|
| Package | PQFP-100 (20x14 mm) | PQFP-100 (same) | PQFP-100 (same) | PQFP-100 (same) | PQFP-100 (same) |
| Brand | Altera | Altera | Altera | Altera | Altera |
| Density | 16 Mb | 8 Mb | 16 Mb | 16 Mb | 16 Mb |
| Configuration Clock (max) | 33 MHz | 33 MHz | 33 MHz | 33 MHz | 33 MHz |
| Supply Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
| In-System Programming | JTAG (IEEE 1149.1) | JTAG | JTAG | JTAG | JTAG |
| Temperature Grade | Commercial | Commercial | Industrial | Industrial | Commercial |
| Lifecycle Status | Obsolete/NRND | Obsolete | Obsolete | Obsolete | Obsolete |
关键差异点
- 16-Mbit density covers the largest legacy Altera bitstreams （对比 EPC8QC100N)
- Single-chip flash + configuration controller （对比 Discrete flash + CPLD controller)
- Altera enhanced configuration interface (33 MHz DCLK) （对比 Passive-serial configuration)
设计说明
Estimated: when migrating from a discrete flash + CPLD controller to the EPC16QC100, designers sometimes leave the nCONFIG/nSTATUS pull-ups on the FPGA side and forget to verify CONF_DONE timing. The PROM drives CONF_DONE high only after the bitstream is fully delivered; if the FPGA's CONF_DONE pull-down remains too strong, the handshake fails. Confirm pull-up values against the target FPGA datasheet.
Place the EPC16QC100 as close as practical to the FPGA to minimize DCLK and DATA0 trace lengths. Add a 0.1 µF ceramic decoupling cap plus a 10 µF bulk cap within 5 mm of the VCC pins. Route DCLK as a controlled-impedance trace; long stubs will cause ringing that the FPGA may interpret as extra clock pulses, corrupting the bitstream.
Because the EPC16QC100 is obsolete/NRND, plan for last-time-buy windows and verify with Intel/Altera FAE before committing production. Recommended: stock a 12–18 month safety inventory and qualify a secondary source (EPC16QI100 or EPC8QC100N) so a single-source line-down is avoided.
合规信息
Compliance information not present in verified web data; set to 'unknown'. EPC family was designed before AEC-Q100 was a typical Altera qualification, so AEC-Q100 is not applicable. Confirm lead-free/RoHS status with Intel/Altera for production orders.