MAX1290ACEI - 400ksps 12-Bit 8-Ch SAR ADC | Maxim Integrated
料号： MAX1290ACEI ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $16.67 | $16.67 |
| 10 | $15.2 | $152.00 |
| 100 | $12.84 | $1,284.00 |
| 500 | $11.5 | $5,750.00 |
| 1,000 | $9.95 | $9,950.00 |
MAX1290ACEI 概述
An ADC (analog-to-digital converter) is a data converter that samples continuous analog voltages and quantizes them into discrete digital codes. SAR (successive-approximation-register) ADCs use a binary search algorithm to resolve N bits in N clock cycles, trading speed for very low power consumption and zero pipeline latency - making them well-suited to multiplexed multi-channel data-acquisition systems, industrial control loops, and any application where a single conversion result must be deterministic and immediately valid. The MAX1290ACEI sits in the data-converter / signal-chain IC hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor.
Key specifications of the MAX1290ACEI include 400 ksps maximum sampling rate through its successive-approximation core, 12-bit resolution, automatic power-down between conversions for low average current, 2 us wake-up time, single +5V analog supply operation, and a separate VLOGIC pin that lets the parallel output bus interface directly with +2.7V to +5.5V digital logic. The internal +2.5V reference removes the need for an external reference IC in most designs.
Architecture is a classic charge-redistribution SAR with an input track-and-hold, switched-capacitor DAC, and comparator. Auto power-down between conversions reduces supply current at low throughput, while a hardware / software shutdown mode drops quiescent draw to microamp levels - critical for battery-powered instrumentation.
Typical applications include multichannel data-acquisition systems, industrial process control, portable instrumentation, patient monitoring, and DSP front ends. The 8 input channels allow direct connection to sensor arrays, while the parallel interface simplifies connection to microcontrollers and DSPs without an external serial-to-parallel converter.
When designing with the MAX1290ACEI, place the 0.1 uF + 10 uF decoupling capacitors as close as possible to the analog supply pins, and ensure the analog and digital grounds meet at a single star point near the ADC to avoid digital-coupling noise on the analog inputs.
This page synthesizes distributor pricing, drop-in same-family and cross-brand alternatives, and practical design notes not found in the manufacturer datasheet.
直接替换替代料： MAX1290ACEI ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： MAX1290ACEI （相同外形与封装尺寸） ——差异在于 RoHS Status, Sampling Rate, Number of Channels, Package, Resolution.
快速对比工具——选择替代料号进行并排对比：
MAX1290BCEI+
✅ 直接替换📋 参考替代料（不在目录中）
MAX1290AEEI+
✅ 直接替换📋 参考替代料（不在目录中）
MAX1290ACEI+T
✅ 直接替换📋 参考替代料（不在目录中）
MAX1290BEEI+
✅ 直接替换📋 参考替代料（不在目录中）
MAX1290BCEI+T
✅ 直接替换📋 参考替代料（不在目录中）
MAX1290ACEI 最大额定值与电气特性
| 分辨率 | 12 bit |
| Number of Input Channels | 8 single-ended / 4 differential |
| 采样率 | 400 ksps |
| ADC Architecture | SAR (Successive Approximation) |
| Analog Supply Voltage | +5 V |
| Digital Logic Supply (VLOGIC) | +2.7 V to +5.5 V |
| Internal Reference Voltage | +2.5 V |
| Wake-Up Time from Shutdown | 2 us |
| 接口 | Byte-wide parallel (8-bit) |
| Automatic Power-Down | Yes (hardware/software controlled) |
| On-Chip Clock | Yes |
| Input Type | Single-ended / pseudo-differential |
| 封装 | 28-pin QSOP |
| 工作温度范围 | 0 C to +70 C (commercial) |
| 安装类型 | Surface Mount |
| RoHS 状态 | Compliant |
MAX1290ACEI 引脚配置
| 引脚 1 | AIN0 — Analog input channel 0 |
| 引脚 2 | AIN1 — Analog input channel 1 |
| 引脚 3 | AIN2 — Analog input channel 2 |
| 引脚 4 | AIN3 — Analog input channel 3 |
| 引脚 5 | AIN4 — Analog input channel 4 |
| 引脚 6 | AIN5 — Analog input channel 5 |
| 引脚 7 | AIN6 — Analog input channel 6 |
| 引脚 8 | AIN7 — Analog input channel 7 |
| 引脚 9 | AGND — Analog ground |
| 引脚 10 | REF — Reference voltage I/O (internal +2.5V or external overdrive) |
| 引脚 11 | VDD — +5V analog supply |
| 引脚 12 | VLOGIC — Digital logic supply (+2.7V to +5.5V) |
| 引脚 13 | DGND — Digital ground |
| 引脚 14 | CS — Chip select (active low) |
| 引脚 15 | RD — Read strobe (active low) |
| 引脚 16 | HBEN — High-byte enable (selects MSB/LSB byte on bus) |
| 引脚 17 | D0/D8 — Data bit 0 (low byte) / bit 8 (high byte) |
| 引脚 18 | D1/D9 — Data bit 1 (low byte) / bit 9 (high byte) |
| 引脚 19 | D2/D10 — Data bit 2 (low byte) / bit 10 (high byte) |
| 引脚 20 | D3/D11 — Data bit 3 (low byte) / bit 11 (high byte, MSB) |
| 引脚 21 | D4 — Data bit 4 |
| 引脚 22 | D5 — Data bit 5 |
| 引脚 23 | D6 — Data bit 6 |
| 引脚 24 | D7 — Data bit 7 |
| 引脚 25 | SHDN — Shutdown input (active low) |
| 引脚 26 | INT/CLK — Conversion end / external clock input |
| 引脚 27 | AVDD — Analog supply (+5V) |
| 引脚 28 | NC — Not connected (per datasheet) |
典型应用
MAX1290ACEI 适用于 6 应用s: Multichannel Data Acquisition Systems, Industrial Process Control, Portable Battery-Powered Instrumentation, Patient Monitoring and Medical Instrumentation, DSP and Microcontroller Front End, Rack-Mounted Test and Measurement Equipment.
Multichannel Data Acquisition Systems
The MAX1290ACEI's 8 single-ended / 4 differential input channels, 400 ksps throughput, and on-chip +2.5V reference make it a single-chip front end for multi-channel DAQ boards used in test stands and laboratory instrumentation. With 12-bit resolution and byte-wide parallel output, it streams converted samples directly into an FPGA or DSP buffer, eliminating the need for an external reference or analog mux. The automatic power-down reduces idle current between scans, and 2 us wake-up keeps scan-cycle overhead negligible at typical scan rates below 100 kHz per channel.
推荐
Industrial Process Control
In PLCs, distributed I/O modules, and process-control front ends, the MAX1290ACEI digitizes 4-20 mA-derived voltage signals from up to 8 sensors per chip. The 12-bit resolution delivers about 0.024% full-scale step size - sufficient for 0.1% accuracy industrial loops. The 0 C to +70 C commercial grade suits cabinet-mounted equipment, while the pin-compatible MAX1290AEEI+ (-40 C to +85 C) covers outdoor and factory-floor nodes. The integrated +2.5V reference eliminates a precision reference IC on the BOM, reducing cost in high-channel-count modules.
推荐
Portable Battery-Powered Instrumentation
Handheld multimeters, portable data loggers, and field instruments benefit from the MAX1290ACEI's automatic power-down mode, which drops supply current to microamp levels between conversions. At 1 ksps aggregate sampling, average supply current is dominated by shutdown current rather than active conversion current, supporting weeks of battery life from a 9V cell. The 2 us wake-up time keeps the active-window overhead low, and the parallel interface avoids the extra clock cycles a serial ADC would require, reducing MCU active time and therefore total system power.
推荐
Patient Monitoring and Medical Instrumentation
The MAX1290ACEI's 8-channel input supports multi-parameter patient monitors that simultaneously sample ECG, respiration, temperature, and SpO2-derived analog signals. The +5V analog supply simplifies the signal-conditioning chain for medical sensors, and the 12-bit resolution is adequate for non-diagnostic monitoring where high-speed high-precision is not required. Note: this is the commercial-temperature MAX1290ACEI; designs requiring medical-grade reliability or wider temperature should select the MAX1290AEEI+ variant. The integrated +2.5V reference and parallel interface reduce overall BOM and board area.
推荐
DSP and Microcontroller Front End
The MAX1290ACEI's byte-wide parallel interface connects directly to the external memory bus of TI C2000 DSPs, NXP ColdFire, and 8051-family microcontrollers without glue logic. A single MOVX-style read latches 8 conversion bits, and a second read captures the remaining 4 LSBs plus status. At 400 ksps, the ADC can continuously feed sample buffers in real-time DSP systems running motor-control, audio, or vibration-analysis algorithms. The 5V analog supply also simplifies front-end signal conditioning for industrial sensors that run off 5V rails.
推荐
Rack-Mounted Test and Measurement Equipment
Bench oscilloscopes, spectrum-analyzer IF digitizers, and automated-test-equipment (ATE) pin cards leverage the MAX1290ACEI's 400 ksps throughput and 8 input channels to digitize multiple test points in parallel. The internal +2.5V reference and on-chip clock simplify board design, while the 28-pin QSOP package fits into the dense layouts of ATE cards. Designers can stack two MAX1290ACEI chips to provide 16 synchronized channels - a common pattern when 12-bit resolution at moderate sample rates is sufficient for production-test throughput requirements.
推荐
推荐产品汇总
工程参考数据： MAX1290ACEI ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX1290BCEI+ | MAX1290AEEI+ | MAX1290ACEI+T | MAX1290BEEI+ | MAX1290BCEI+T |
|---|---|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Package | 28-QSOP | 28-QSOP - same | 28-QSOP - same | 28-QSOP - same | 28-QSOP - same | 28-QSOP - same |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| Sampling Rate | 400 ksps | 400 ksps | 400 ksps | 400 ksps | 400 ksps | 400 ksps |
| Input Channels | 8 single-ended / 4 differential | 8 single-ended / 4 differential | 8 single-ended / 4 differential | 8 single-ended / 4 differential | 8 single-ended / 4 differential | 8 single-ended / 4 differential |
| Operating Temperature | 0 C to +70 C (commercial) | 0 C to +70 C (commercial) | -40 C to +85 C (industrial) | 0 C to +70 C (commercial) | -40 C to +85 C (industrial) | 0 C to +70 C (commercial) |
| Lead-Free / RoHS | Per commercial order code | Yes (lead-free) | Yes (lead-free) | Per commercial order code | Yes (lead-free) | Yes (lead-free) |
| Packaging Format | Tube | Tube | Tube | Tape & Reel | Tube | Tape & Reel |
关键差异点
- Integrated +2.5V reference and on-chip clock （对比 MAX1290BCEI+)
- Automatic power-down with 2 us wake-up （对比 MAX1290AEEI+)
- 8/4 channel multiplexed input in 28-QSOP （对比 MAX1292 (24-pin QSOP, 4 channels))
设计说明
The MAX1290ACEI requires clean +5V on AVDD and a separate +2.7V to +5.5V on VLOGIC. Place a 0.1 uF X7R ceramic bypass capacitor as close as possible to each supply pin, with a 10 uF bulk tantalum or ceramic on the analog supply. Tie AVDD and VLOGIC together if the system is 5V-only - the device allows a single-rail configuration, but a small ferrite bead between the two pins reduces digital switching noise coupling into the analog section.
Use a star-ground topology: route AGND and DGND back to a single point near the ADC. Keep analog input traces short and surrounded by a ground guard ring to reduce digital-coupling noise. The 28-QSOP footprint requires thermal relief on all pads; avoid running high-current digital return paths beneath the analog input pins. For best 12-bit performance, use a continuous analog ground plane on the top layer with the ADC on the top side, and stitch the bottom-side digital ground to the top with vias near the DGND pin.
Do not leave the SHDN pin floating - tie it high (logic 1) through a 100 kohm pull-up to VLOGIC for normal operation. A floating SHDN pin can intermittently shut down the converter. The REF pin requires a 0.1 uF + 10 uF external capacitor network to keep the internal +2.5V reference stable; omitting the bulk capacitor degrades SNR by several dB. The HBEN pin must be driven by the host controller - it is not internally pulled. Read the datasheet's digital-interface timing diagram before laying out the parallel-bus connections, since a CS-to-RD setup-time violation produces corrupted data on the high byte.
合规信息
RoHS compliance confirmed via distributor listings and the Analog Devices product page. Lead-free status of the bare MAX1290ACEI (no + suffix) is part-specific - for lead-free RoHS-compliant build, choose the MAX1290BCEI+ or MAX1290ACEI+T variants. AEC-Q100 is not applicable (no automotive-qualified variant in the MAX1290 family).
