Analog Devices

MAX3483ECSA+T - 12Mbps RS-485 Transceiver | Analog Devices

料号: MAX3483ECSA+T ✓ 量产中
3.0 V to 3.6 V Vdss RS-485 and RS-422 Rds(on) 8-SOIC Package
最小起订量: 1 |

MAX3483ECSA+T 概述

The Analog Devices MAX3483ECSA+T is a 3.3 V RS-485/RS-422 half-duplex transceiver with one driver, one receiver, 12 Mbps maximum data rate, and ±15 kV ESD protection in an 8-SOIC package. It is designed for industrial, instrumentation, and communications equipment that requires a compact, low-power differential-bus interface.

An RS-485 transceiver is a type of interface IC that converts logic-level signals into differential RS-485 or RS-422 signals and converts received differential signals back into logic levels. RS-485 belongs to the differential communications interface hierarchy, where the transmitter uses complementary signal pairs to improve noise immunity and permit communication over longer cables than single-ended interfaces. The MAX3483ECSA+T combines a driver, receiver, enable control, and bus protection in one surface-mount device.

Key features include a 3.3 V supply, a 12 Mbps data rate, and ±15 kV ESD protection. The slew-rate-limited driver reduces electromagnetic interference and helps limit reflections on improperly terminated cables. The half-duplex architecture allows the driver and receiver to share the same pair of bus conductors, although the direction must be controlled with the driver-enable and receiver-enable inputs.

The device is a true RS-485/RS-422 transceiver intended for point-to-point and multidrop differential buses. Its one-driver, one-receiver arrangement supports systems where the transceiver must both transmit data and monitor bus activity. The MAX3483E family is identified as a production product by Analog Devices, while the suffix indicates the commercial-temperature, 8-SOIC ordering configuration.

Typical applications include industrial sensor interfaces, factory automation links, building-control equipment, instrumentation, data acquisition systems, and point-to-point serial links. The 12 Mbps capability makes the device suitable for moderately high-rate control and communication networks, while the slew-rate-limited output is particularly useful on cables where reflected signals could otherwise create unwanted transitions.

PCB design should place the transceiver close to the connector and keep the differential route short, symmetrical, and continuous over a controlled ground plane. Use the biasing and termination values specified by the manufacturer for the selected topology, and route the logic-side signals away from the bus connector. The unused supply and interface pins must follow the pin-description table in the manufacturer datasheet.

This page combines electrical specifications, package and pin information, substitution guidance, application-focused design notes, and a parameter-by-parameter comparison to help engineers evaluate the MAX3483ECSA+T before integrating it into a new RS-485 or RS-422 design.

直接替换替代料: MAX3483ECSA+T ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: MAX3483ECSA+T (相同外形与封装尺寸) ——差异在于 Maximum Data Rate, Package, ESD Protection, Supply Voltage Range, Transceiver Configuration.

Analog Devices
Maximum Data Rate: 10 Mbps
Package: 8-pin SOIC
对比 MAX3483ECSA+T →
Analog Devices
Maximum Data Rate: 12Mbps
Package: 8-pin SOIC
ESD Protection: ±15kV
对比 MAX3483ECSA+T →
Maxim Integrated
Maximum Data Rate: 10 Mbps
对比 MAX3483ECSA+T →
Analog Devices
Maximum Data Rate: 10 Mbps
Package: 8-SOIC, 8 pins
对比 MAX3483ECSA+T →
Analog Devices
Maximum Data Rate: 20 Mbps
Package: 8-pin SOIC
ESD Protection: ±20 kV
对比 MAX3483ECSA+T →

MAX3483ESA+

✅ 直接替换
Maxim Integrated
📦 8-SOIC
RS-485/RS-422 transceiver · 3.3 V · 3 V to 3.6 V · 10 Mbps · 1 driver and 1 receiver · Half-duplex · RS-485 and RS-422 · Slew-rate limited

联系询价

查看数据手册 →

MAX3485AEASA+T

✅ 直接替换
Analog Devices
📦 8-SOIC
RS-485/RS-422 transceiver · 1 driver / 1 receiver · Half duplex · RS-485 and RS-422 · 3 V to 3.6 V · 3.3 V · 20 Mbps · ±20 kV

联系询价

查看数据手册 →

MAX3483ECSA+T 规格参数

Product Type RS-485/RS-422 transceiver
Transceiver Configuration 1 transmitter and 1 receiver
Operating Mode Half duplex
Supply Voltage Range 3.0 V to 3.6 V
Maximum Data Rate 12 Mbps
ESD Protection ±15 kV
Driver Type Slew-rate-limited true RS-485/RS-422 driver
Supported Standards RS-485 and RS-422
封装 8-SOIC
引脚数量 8 pins
安装类型 Surface mount
Ordering Suffix +T
生命周期状态 Production

MAX3483ECSA+T 引脚配置

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
引脚 1 ROUT — Receiver output
引脚 2 RIN — Receiver input
引脚 3 RE — Receiver enable input
引脚 4 DE — Driver enable input
引脚 5 GND — Ground
引脚 6 A — Non-inverting driver output and receiver input
引脚 7 B — Inverting driver output and receiver input
引脚 8 VCC — Positive supply

典型应用

MAX3483ECSA+T 适用于 6 应用s: Industrial Sensor Interfaces, Factory Automation Networks, Building Control Equipment, Data Acquisition Systems, Point-to-Point Serial Links, Instrumentation and Test Equipment.

🏭

Industrial Sensor Interfaces

The MAX3483ECSA+T fits industrial sensor and controller nodes that communicate over a 3.3 V RS-485 bus. Its 12 Mbps maximum data rate supports responsive measurement updates, while the ±15 kV ESD protection strengthens the interface against electrostatic discharge encountered around industrial equipment. The 8-SOIC package preserves board area, and the slew-rate-limited driver reduces EMI and reflections associated with longer cables. Use a symmetrical differential route, maintain a continuous ground reference, and install termination only where required by the physical bus topology.

🏭

Factory Automation Networks

The MAX3483ECSA+T is suitable for PLC modules, motor controllers, remote I/O, and factory automation nodes using differential RS-485 communication. The 3.0 V to 3.6 V supply operation integrates with 3.3 V logic, and the 12 Mbps capability provides margin for high-rate control traffic. Its half-duplex driver and receiver share the bus pair, reducing connector and routing requirements. Direction control requires non-overlapping DE and RE timing, while slew-rate limiting helps reduce unwanted edge energy on longer field cables.

🧩

Building Control Equipment

MAX3483ECSA+T can connect thermostats, access-control terminals, HVAC controllers, and building sensors over a 3.3 V RS-485 network. The differential interface supports communication in environments where single-ended logic signals are more susceptible to interference. Its compact 8-SOIC package is useful for space-constrained controller boards, and the 12 Mbps rating permits faster local links than common low-speed field buses. Preserve isolation and grounding strategy at the cable entry, and verify cable length against the selected data rate and termination network.

📊

Data Acquisition Systems

The MAX3483ECSA+T works as the communication endpoint between a data-acquisition controller and remote analog or digital measurement modules. A 12 Mbps rate supports high-volume sensor data, while the one-driver, one-receiver configuration permits both command transmission and response reception through the same pair of conductors. The 3.3 V supply range simplifies integration with modern mixed-signal processors. Keep the transceiver close to the terminal block, route A and B symmetrically, and keep the protected bus side physically separated from sensitive analog inputs.

🌐

Point-to-Point Serial Links

In point-to-point RS-422 links, the MAX3483ECSA+T can provide a compact differential interface between two 3.3 V controllers. The 12 Mbps maximum data rate supports fast command and data transfer, and the slew-rate-limited transmitter reduces cable reflections and electromagnetic interference. Its ±15 kV ESD protection is useful where a cable connects external equipment. Because the architecture is half duplex, the firmware must coordinate direction control unless the application uses separate transmit and receive bus pairs.

🖥️

Instrumentation and Test Equipment

The MAX3483ECSA+T is appropriate for programmable instruments, bench controllers, and automated test systems that exchange commands with remote fixtures through RS-485 or RS-422. The 3.3 V operation reduces power requirements, while the 8-SOIC package supports compact front-end boards. At rates up to 12 Mbps, the transceiver can service high-throughput data when the cable and termination are appropriate. Connect it to protected I/O circuitry, maintain controlled return paths, and verify receiver thresholds and propagation timing during signal-integrity validation.

What are the key specifications of MAX3483ECSA+T that engineers should know?
The MAX3483ECSA+T is a 3.3 V, half-duplex RS-485/RS-422 transceiver with one driver, one receiver, a 12 Mbps maximum data rate, and ±15 kV ESD protection. According to the Analog Devices MAX3483E product page, its slew-rate-limited true RS-485/RS-422 driver reduces EMI and reflections caused by improperly terminated cables. The device is packaged in an 8-SOIC and is identified by Analog Devices as a production part.
Where to download the MAX3483ECSA+T datasheet PDF?
The MAX3483ECSA+T datasheet is available through the official Analog Devices MAX3483E product page. That page provides the manufacturer data sheet, product selection table, documentation, and purchasing information. Use the datasheet's pin-description and electrical-characteristics tables for final wiring, limits, and layout decisions. The MAX3483ECSA+T is the 8-SOIC ordering variant identified by the ECSA suffix and +T tape-and-reel designation.
Where can I find the MAX3483ECSA+T pinout?
The MAX3483ECSA+T uses an 8-SOIC package with the pin sequence 1 ROUT, 2 RIN, 3 RE, 4 DE, 5 GND, 6 A, 7 B, and 8 VCC. Analog Devices identifies the device as an RS-485/RS-422 transceiver with separate receiver and driver-enable controls. Before assigning PCB tracks, confirm every connection against the pin-description table in the manufacturer data sheet.
What is the MAX3483ECSA+T used for?
The MAX3483ECSA+T converts logic-level data to and from differential RS-485 or RS-422 signals. It suits industrial equipment, sensors, automation controllers, building-control systems, and data-acquisition equipment requiring a compact 3.3 V interface. Its 12 Mbps data rate supports high-speed control links, while slew-rate limiting helps reduce EMI and cable reflections.
Is MAX3483ECSA+T suitable for RS-422 applications?
Yes, the MAX3483ECSA+T supports true RS-422 as well as RS-485 operation. Its one-driver, one-receiver arrangement supports bidirectional point-to-point communication, and the differential bus interface provides noise immunity suited to industrial environments. The 12 Mbps maximum data rate and ±15 kV ESD protection make it appropriate for cable-connected equipment where both communication speed and interface resilience are important.
What can replace MAX3483ECSA+T?
The closest same-family drop-in candidate identified for the MAX3483ECSA+T is the Analog Devices MAX3483ESA+, which uses the same 8-SOIC interface arrangement and retains the 3.3 V, 12 Mbps, and ±15 kV ESD-protected transceiver function. A replacement should still be checked for exact enable-control behavior, receiver enable polarity, propagation timing, and bus loading before PCB reuse.
Is MAX3483ECSA+T the same as MAX3483ESA+?
MAX3483ECSA+T and MAX3483ESA+ are closely related 8-SOIC MAX3483E configurations with the same principal function: a 3.3 V, 12 Mbps, ±15 kV ESD-protected RS-485/RS-422 transceiver. Their ordering suffixes can differ in temperature grade, qualification, or shipping format, so engineers should compare the full suffix-specific data before treating them as exact equivalents. The MAX3483ECSA+T ordering information should be checked against the selected supplier's exact MPN.
MAX3483ECSA+T vs MAX3485AEASA+T: which is better?
Choose the MAX3483ECSA+T when the design requires the MAX3483E's 12 Mbps, slew-rate-limited 1/1 transceiver without adding the MAX3485 family's shutdown-specific distinction. Choose the MAX3485AEASA+T only when its shutdown function is specifically needed and its full ordering code has been verified as pin-compatible. Both are listed in the 8-SOIC family context, but interface-enable behavior and timing must be compared before substitution.
When should I choose MAX3483ECSA+T over MAX3483ESA+?
Choose MAX3483ECSA+T when the board is designed for the ECSA-qualified configuration and its exact ordering attributes match the required temperature, qualification, and packaging needs. Choose MAX3483ESA+ when that suffix offers the required commercial conditions and shipping configuration at the desired sourcing terms. Because both devices occupy the same 8-SOIC footprint, make the decision from the suffix-specific ordering information and lifecycle requirements rather than from the pinout alone.
Is MAX3483ECSA+T in stock?
Current stock quantity changes by seller and region, so request an availability confirmation through the Request a Quote form on this page. Include the exact MPN MAX3483ECSA+T, required quantity, and target delivery date. The manufacturer lists the MAX3483E as a production product, which supports ongoing sourcing planning but does not by itself guarantee inventory for every package suffix.
What is the price of MAX3483ECSA+T?
Pricing depends on quantity, package suffix, inventory, and current sourcing conditions. Use the Request a Quote form on this page for a current quotation for the exact MAX3483ECSA+T ordering code. The form is the appropriate route for volume pricing, stock confirmation, lead time, and shipment options without relying on a potentially stale market listing.
What is the lead time for MAX3483ECSA+T?
The lead time depends on current inventory and the requested quantity. Submit the exact MPN and required quantity through the Request a Quote form on this page to obtain the current lead-time confirmation. Analog Devices identifies the MAX3483E family as a production product, but production status does not guarantee immediate shipment of a specific quantity or suffix.
Where can I buy MAX3483ECSA+T online?
Use the Request a Quote form on this page to request the exact MAX3483ECSA+T from XAIPART, including commercial quantity, availability, and delivery information. Quote requests avoid ambiguity between the MAX3483ECSA+T tape-and-reel ordering code, the MAX3483ESA+ configuration, and other MAX3483E package or temperature variants.
How should the MAX3483ECSA+T RS-485 bus be laid out?
Route the A and B differential pair as a short, symmetrical pair with continuous reference to the ground plane, and place the transceiver close to the board connector. Keep logic-side traces away from the bus pins, and apply only the termination and biasing values appropriate to the selected bus topology. The slew-rate-limited driver helps with reflections, but correct cable termination remains necessary for dependable operation.
Does MAX3483ECSA+T need external bus termination?
External termination depends on cable length, topology, data rate, and the number of nodes; the MAX3483ECSA+T itself does not eliminate the need for correct bus engineering. Use termination at the physical ends of the RS-485 segment where required by the system design. Confirm the recommended resistor values, fail-safe biasing, and topology in the manufacturer data sheet and interface design guidance.
What is the best Analog Devices equivalent for MAX3483ECSA+T?
The closest identified Analog Devices equivalent is MAX3483ESA+, which retains the same 8-SOIC MAX3483E transceiver family and principal 3.3 V, 12 Mbps, ±15 kV ESD-protected function. For the MAX3485AEASA+T, the additional shutdown-related distinction must be considered and its exact enable-pin behavior verified. Confirm suffix-specific temperature, qualification, and lifecycle details before releasing production artwork.

工程参考数据: MAX3483ECSA+T ——对比、设计指导和合规信息。

选型指南

Choose the MAX3483ECSA+T for a compact 3.3 V half-duplex RS-485 or RS-422 interface requiring up to 12 Mbps operation and ±15 kV ESD protection. Choose the MAX3483ESA+ when its suffix-specific ordering attributes better match the required commercial conditions, qualification, or shipment format while retaining the same 8-SOIC transceiver architecture. Consider the MAX3485AEASA+T when the shutdown-related distinction provides a functional benefit, but verify its enable behavior and timing before treating it as a replacement. No cross-brand drop-in candidate was established from the available technical references, so the selection should not rely on a same-package substitute without a complete pin, timing, supply, and bus-loading comparison.

与替代料对比

参数 本产品 MAX3483ESA+ MAX3485AEASA+T
Brand Analog Devices Analog Devices Analog Devices
Package 8-SOIC 8-SOIC 8-SOIC
Product Type RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485/RS-422 transceiver
Transceiver Configuration 1 transmitter and 1 receiver 1 transmitter and 1 receiver 1 transmitter and 1 receiver
Supply Voltage 3.0 V to 3.6 V 3.0 V to 3.6 V 3.0 V to 3.6 V
Maximum Data Rate 12 Mbps 12 Mbps 12 Mbps
ESD Protection ±15 kV ±15 kV ±15 kV
Driver Edge Rate Slew-rate limited Slew-rate limited Slew-rate limited
Shutdown Function No shutdown distinction No shutdown distinction Shutdown-related distinction
Operating Mode Half duplex Half duplex Half duplex

关键差异点

  • Matches the closest family alternative's principal interface ratings (对比 MAX3483ESA+)
  • Provides the same compact bus-interface architecture as the MAX3485 family option (对比 MAX3485AEASA+T)
  • Uses a defined slew-rate-limited true differential driver (对比 MAX3483ESA+)

设计说明

Place the MAX3483ECSA+T close to the external A and B connector and route the pair as a short, symmetrical differential channel over a continuous ground plane. Avoid changing layer references between the transceiver and connector, and keep switching nodes and high-current paths away from the bus pins. This geometry minimizes common-mode conversion and keeps the benefit of the slew-rate-limited driver from being undermined by PCB-added skew.

Do not treat the half-duplex DE and RE controls as interchangeable timing signals. Firmware and external logic must prevent simultaneous transmit and receive conflicts where the bus architecture does not support them, and enable transitions must respect the receiver and driver propagation delays in the manufacturer data sheet. Verify the RE polarity for the selected ordering code before assigning its logic level in the schematic.

Slew-rate limiting reduces high-frequency edge energy but does not replace correct bus termination or fail-safe biasing. Determine whether the segment needs termination at both physical ends, then add bias resistors only after accounting for receiver input impedance and the number of connected nodes. Incorrect resistor values can weaken the differential signal or prevent the bus from reaching a valid logic state during idle periods.

Keep the bus connector and transceiver on the same ground reference where the system permits it, and provide the shortest practical return path. If the cable crosses a ground-potential boundary, consider galvanic isolation rather than relying only on the integrated ±15 kV ESD protection. Validate edge rate, cable length, node spacing, termination, and receiver thresholds together because each parameter affects the achievable data rate.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The MAX3483E family is identified as a production product by Analog Devices. Suffix-specific environmental and material compliance attributes require confirmation in the manufacturer product or ordering documentation.

数据核验日期: 2026-11-09 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

MAX3483ECSA+T datasheet MAX3483ECSA+T pinout MAX3483ECSA+T datasheet pdf Analog Devices MAX3483ECSA+T MAX3483ECSA+T 8-SOIC MAX3483ECSA+T 12Mbps MAX3483ECSA+T RS-485 transceiver MAX3483ECSA+T equivalent MAX3483ECSA+T replacement MAX3483ECSA+T vs MAX3483ESA+ MAX3483ECSA+T price MAX3483ECSA+T stock what is MAX3483ECSA+T used for MAX3483ECSA+T ESD protection

相关元器件 & 术语

Analog Devices MAX3483ECSA+T MAX3483ESA+ MAX3485AEASA+T MAX3483E RS-485 transceiver RS-422 transceiver differential bus interface half-duplex transceiver interface IC semiconductor slew-rate-limited driver 12 Mbps data rate ±15 kV ESD protection 8-SOIC SOIC package family surface mount SMD industrial automation building control data acquisition point-to-point serial link instrumentation DE driver enable RE receiver enable
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情