Analog Devices

MAX361CSE+ - Quad SPST Analog Switch | Analog Devices

料号: MAX361CSE+ ✓ 量产中
<85 ohm Rds(on) 16-SOIC, 3.90 mm body width Package
最小起订量: 1 |

MAX361CSE+ 概述

Analog Devices MAX361CSE+ is a precision, quad, single-pole single-throw analog switch with four normally closed switches, packaged in a 16-pin SOIC. The device provides low channel on resistance of less than 85 ohms, with on-resistance matching maintained within 3 ohms between channels. Its on resistance remains flat across the analog signal range, with a maximum change of 9 ohms. The MAX361CSE+ is designed for precision signal-routing systems where repeatable resistance, low leakage, and consistent channel behavior are important.

An analog switch is a semiconductor device that routes analog signals between terminals under digital control. The MAX361CSE+ belongs to the analog switch and multiplexer hierarchy, where a multiplexer combines switching functions with signal selection. Its four normally closed SPST channels default to the connected state when the control input is inactive. This architecture is useful in test systems, measurement instruments, audio paths, sensor interfaces, and communication equipment that require controlled switching of low-voltage signals.

The primary benefit of the MAX361CSE+ is channel-to-channel consistency. According to the Analog Devices MAX361 product page, the device guarantees less than 85 ohms of on resistance and matching within 3 ohms among channels. The on-resistance characteristic changes by no more than 9 ohms across the supported analog signal range. These specifications reduce gain error and channel-to-channel variation when the same source resistance, amplifier gain, or measurement calibration is used across multiple switched paths.

The MAX361CSE+ contains four independent precision SPST switches, allowing a system to connect or isolate several signal lines without changing the PCB footprint. Its 16-pin narrow SOIC package supports conventional surface-mount assembly and keeps the routing distance between external circuitry and the switch short. The manufacturer identifies the MAX361 family as being in production and lists the MAX361 data sheet as Revision 2.

Typical uses include front-end signal selection, instrumentation amplifiers, automated test equipment, data acquisition systems, and audio routing networks. Because the switches are normally closed, they can also preserve signal continuity during control-signal transitions or provide a default connection when an external controller is unavailable. Designers should still account for injected power, off-state isolation, control logic levels, and signal amplitude when constructing the surrounding analog circuit.

Layout and signal integrity require attention around high-impedance analog paths. Keep input and output traces short, use a continuous ground reference, and avoid routing sensitive signals next to clocked or switching circuitry. Verify the control levels and operating conditions in the MAX361 data sheet before relying on a default state during power-up. Decoupling and protection components should be selected from the actual signal bandwidth, source impedance, and external voltage limits.

This product page combines the MAX361CSE+ technical description with package information, application guidance, design notes, and a focused comparison against identified same-package alternatives. It is intended to help engineers distinguish the normally closed MAX361 from other switching functions and to plan PCB, sourcing, and signal-path decisions around the verified 16-pin SOIC implementation.

直接替换替代料: MAX361CSE+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

MAX361ESE+

✅ 直接替换
📦 16-SOIC
Same 16-SOIC quad SPST family, but the E suffix may change temperature-grade requirements; verify operating limits

📋 参考替代料(不在目录中)

MAX361CSE

✅ 直接替换
📦 16-SOIC
Same functional and terminal arrangement is reported, with ordering-suffix qualification requiring final verification

📋 参考替代料(不在目录中)

MAX361CSE+ 最大额定值与电气特性

Number of Switches 4 circuits
Switch Type Single-pole single-throw (SPST)
Default Switch State Normally closed (NC)
On Resistance <85 ohm
On-Resistance Matching Between Channels <=3 ohm
On-Resistance Variation Over Analog Signal Range <=9 ohm
Number of Control Inputs 4 inputs
封装 16-SOIC, 3.90 mm body width
安装类型 Surface mount
RoHS 状态 unknown
Data Sheet Revision Revision 2

MAX361CSE+ 16-soic, 3.90 mm body width 引脚配置指南

MAX361CSE+(16-soic, 3.90 mm body width 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

MAX361CSE+ 的 16-soic, 3.90 mm body width 封装引脚图

暂无详细引脚数据: MAX361CSE+.

请参阅 数据手册 以查看完整引脚配置。

典型应用

MAX361CSE+ 适用于 6 应用s: Automated Test Equipment Signal Routing, Precision Data Acquisition Front Ends, Audio Signal Path Switching, Sensor Interface Multiplexing, Instrumentation Amplifier Input Selection, Communication Signal Isolation.

🖥️

Automated Test Equipment Signal Routing

The MAX361CSE+ fits automated test equipment that must connect several analog measurement paths to a shared input while preserving continuity during inactive periods. Its four normally closed SPST channels provide a defined default connection, and the less-than-85-ohm on resistance, 3-ohm maximum channel matching, and 9-ohm maximum variation across the analog signal range reduce path-dependent errors. Place each common terminal near its precision amplifier or measurement front end, then use the switched terminals to select the source under test. Review leakage, switching transients, control levels, and source impedance before setting the measurement bandwidth.

📡

Precision Data Acquisition Front Ends

The MAX361CSE+ is suitable for data-acquisition front ends that select among sensors or conditioned analog inputs. Consistent on resistance helps maintain similar source loading across channels, while the 3-ohm channel matching and 9-ohm maximum change over the analog signal range support repeatable gain and calibration behavior. The normally closed configuration can maintain a selected input path when a controller is inactive. Use short traces, a solid ground reference, and low-leakage surrounding components when working with high-impedance sources. The official data sheet should define the usable signal range and leakage limits for the selected operating conditions.

🎧

Audio Signal Path Switching

The MAX361CSE+ can route low-level audio signals in mixer, selector, and monitoring circuits where four normally closed channels simplify default signal continuity. Its on resistance below 85 ohms provides a defined insertion impedance, and channel matching within 3 ohms limits gain variation between switched inputs. Audio designs should still account for switch leakage, control transients, ground offsets, and the frequency-dependent behavior of surrounding traces and capacitors. Position the device near the source and destination to minimize pickup, and compare the measured channel response during equalization or calibration.

🧩

Sensor Interface Multiplexing

The MAX361CSE+ fits sensor-interface designs that need to isolate or route multiple low-voltage sensor outputs through a common conditioning amplifier. The quad SPST topology provides independent channel control, while the less-than-85-ohm on resistance and close channel matching help maintain similar loading among sensors. Normally closed channels can preserve a connection when control logic is inactive, which is useful in fail-safe routing. For high-impedance sensors, evaluate leakage and capacitance because those parameters can dominate accuracy even when the documented on-resistance target is met. Use a low-leakage protection network and avoid long parallel signal routes.

🏭

Instrumentation Amplifier Input Selection

The MAX361CSE+ can select among multiple inputs feeding an instrumentation-amplifier front end in laboratory and industrial measurement systems. Its guaranteed channel matching of 3 ohms and maximum on-resistance variation of 9 ohms across the analog range help minimize switching-induced gain differences. The 16-pin SOIC format allows the four switch channels to be placed close to the amplifier inputs, reducing trace length and susceptibility to interference. Validate the switch contribution against the complete signal chain, including amplifier input bias current, source impedance, leakage, control timing, and the acquisition bandwidth.

🌐

Communication Signal Isolation

The MAX361CSE+ can support signal isolation and routing in communication and interface circuits that require normally closed SPST paths. The low on resistance and controlled matching provide repeatable channel behavior when lines are connected or disconnected, while four independent switches allow separate control of multiple paths. For high-frequency or low-amplitude signals, include the complete circuit response because package parasitics, trace inductance, control coupling, and capacitance are not represented by the basic on-resistance figure. Keep the layout compact, maintain a continuous ground plane, and verify that the control-driver transitions do not create unacceptable disturbances on sensitive channels.

What is the MAX361CSE+?
The MAX361CSE+ is a precision, quad, single-pole single-throw analog switch with four normally closed channels in a 16-pin SOIC package. Analog Devices describes the MAX361 family as a production device with low channel on resistance, close matching between channels, and low leakage. Its four independent switches can route or isolate low-voltage analog signals under digital control.
How many switches does the MAX361CSE+ contain?
The MAX361CSE+ contains four independent SPST switches, and every channel is normally closed. The 16-pin SOIC provides four common terminals, four switched terminals, and the associated control inputs. The manufacturer identifies the device as a precision quad SPST analog switch with on resistance below 85 ohms.
What is the on resistance of the MAX361CSE+?
The MAX361CSE+ has a channel on resistance of less than 85 ohms. According to the Analog Devices MAX361 product page, matching between channels is maintained within 3 ohms, while the on resistance remains flat over the analog signal range with a maximum change of 9 ohms. These figures help control gain error when multiple switched paths feed sensitive circuitry.
Is the MAX361CSE+ normally open or normally closed?
The MAX361CSE+ is normally closed. According to the Analog Devices MAX361 product description, the MAX361 has four normally closed SPST switches, whereas the MAX362 family provides normally open switches. Choose the MAX361 when the default electrical state must maintain continuity between each common and switched terminal.
Where can I download the MAX361CSE+ datasheet PDF?
The official MAX361 datasheet is available through the Analog Devices product page at https://www.analog.com/en/products/max361.html. The manufacturer identifies the document as the MAX361/MAX362 Precision, Quad, Single-Pole Single-Throw Analog Switches Data Sheet, Revision 2. Use the pin-description table and electrical-characteristics tables for final design verification.
Where can I find the MAX361CSE+ pinout?
The MAX361CSE+ pin assignment is shown in the official MAX361/MAX362 data sheet linked from the Analog Devices MAX361 product page. The device uses a 16-pin SOIC package. Use the manufacturer pin-description table when assigning common terminals, switched terminals, and control inputs, especially when normal closed-state behavior must be preserved.
What can replace the MAX361CSE+?
MAX361ESE+ and MAX361CSE are identified same-package alternatives to the MAX361CSE+, but each requires a final comparison of temperature grade, pin configuration, electrical limits, and lifecycle status before substitution. The manufacturer product page should be used to confirm the ordering suffix and the official data sheet should be used to verify pin compatibility. No cross-brand drop-in replacement was established.
Can MAX361ESE+ replace MAX361CSE+?
MAX361ESE+ can serve as a candidate replacement for MAX361CSE+ because comparison information identifies both as 16-pin, four-channel SPST analog switches in the narrow SOIC family. However, suffix selection can change temperature grade or operating limits. Confirm the pinout, supply range, analog signal range, leakage, and switching specifications in the MAX361 data sheet before approving the substitution.
Is MAX361CSE the same as MAX361CSE+?
MAX361CSE and MAX361CSE+ are listed as replacement-compatible 16-pin SOIC parts with consistent terminals, package, and functional characteristics. The ordering suffixes still require manufacturer-level review because they can indicate different qualification, temperature, or packaging conditions. Compare the exact suffix details and operating limits rather than treating the suffixes as interchangeable without verification.
When should I choose MAX361CSE+ over MAX361ESE+?
Choose MAX361CSE+ when its exact ordering suffix satisfies the required temperature grade and operating limits while using the verified normally closed, four-channel SPST configuration. Choose MAX361ESE+ when its suffix provides a necessary manufacturing, grade, or lifecycle advantage after pin and electrical comparisons are completed. Both candidates use the 16-pin narrow SOIC format, but the suffix-specific constraints determine final suitability.
Is MAX361CSE+ suitable for test and measurement systems?
The MAX361CSE+ is suitable for test and measurement signal paths that require four normally closed SPST channels with consistent resistance. Its on resistance is below 85 ohms, channel matching is within 3 ohms, and variation across the analog signal range is limited to 9 ohms maximum. Account for source impedance, leakage, switching transients, and control timing when estimating measurement error.
Does the MAX361CSE+ require a heatsink?
The MAX361CSE+ is a low-power analog switch rather than a power-conversion device, so a separate heatsink is generally not the primary thermal consideration. Thermal design should instead account for total supply dissipation, ambient temperature, PCB copper, and nearby heat sources. The exact power dissipation and maximum junction temperature must be confirmed from the official electrical and absolute-maximum ratings.
What is the lifecycle status of the MAX361CSE+?
The MAX361 family is marked as production on the Analog Devices product page as of 2026-11-09. This supports active sourcing for new designs, although the exact MAX361CSE+ orderable configuration should be confirmed for production quantities. Lifecycle confirmation does not replace checking the suffix-specific supply and operating requirements.
Where can I buy the MAX361CSE+ and check its lead time?
Use the Request a Quote form on this page to ask for MAX361CSE+ availability, current lead time, minimum order quantity, and production packaging. The request can include the target quantity and date required by the project. Quote responses should also confirm the exact MAX361CSE+ suffix and delivery schedule.
What is the price of the MAX361CSE+?
The current MAX361CSE+ price depends on order quantity, sourcing channel, and the requested production configuration. Use the Request a Quote form on this page and specify the required quantity, target date, and packaging preference. The quote response provides the applicable commercial terms without embedding a potentially stale price in technical documentation.
Is the MAX361CSE+ in stock?
Current MAX361CSE+ inventory should be confirmed through the Request a Quote form on this page. Include the required quantity, delivery date, and approved packaging in the request so the response can reflect the correct orderable configuration. The Analog Devices product page identifies the MAX361 family as production, but exact stock is a commercial question.
What are the key specifications of MAX361CSE+ that engineers should know?
The MAX361CSE+ is a 16-pin SOIC analog switch with four normally closed SPST channels. According to the Analog Devices MAX361 product page, each channel has less than 85 ohms of on resistance, channel-to-channel matching is within 3 ohms, and on-resistance variation across the analog signal range is no more than 9 ohms. Its low-leakage design supports precision analog routing.

工程参考数据: MAX361CSE+ ——对比、设计指导和合规信息。

选型指南

Choose MAX361CSE+ when the design requires four independent normally closed SPST channels in a 16-pin SOIC and benefits from on resistance below 85 ohms, channel matching within 3 ohms, and no more than 9 ohms of resistance variation across the analog signal range. Choose MAX361ESE+ when its ordering suffix provides a required temperature-grade, qualification, or lifecycle advantage after the official pin and electrical limits are checked. MAX361CSE is another same-family candidate whose package and terminal compatibility are reported, but its suffix must be verified before qualification. Neither identified alternative changes the fundamental architecture, so the normally closed state, leakage, control timing, and exact ordering-suffix limits remain the decisive criteria. No cross-brand drop-in candidate was established, making the Analog Devices options the safest starting points for a footprint-preserving review.

与替代料对比

参数 本产品 MAX361ESE+ MAX361CSE
Brand Analog Devices Analog Devices Analog Devices
Package 16-SOIC, 3.90 mm body width 16-SOIC narrow 16-SOIC
Number of Channels 4 4 4

关键差异点

  • Four normally closed precision channels (对比 MAX361CSE)
  • Controlled channel matching (对比 MAX361ESE+)
  • Flat on-resistance behavior (对比 MAX361CSE)

设计说明

Route common and switched terminals as short, direct analog paths, especially when driving high-impedance sensors or precision amplifiers. The MAX361CSE+ specifies less than 85 ohms of on resistance, but the complete path also includes trace resistance, connector resistance, leakage, and switching capacitance. Maintain a continuous ground reference beneath the signal routes and evaluate the assembled path rather than relying on the IC specification alone.

Place the four channels near their associated signal sources and destinations to minimize loop area and coupling from control signals. Keep clock, digital, and power-switching nodes away from sensitive analog terminals. If the control inputs drive long traces, add appropriate impedance control near the device and verify switching transients with an oscilloscope under the intended load and bandwidth.

Do not assume that the normally closed state is electrically idle: the signal path remains connected when the control input is inactive. Check control-logic polarity, startup behavior, and fault conditions to ensure that the default connection cannot create an unwanted signal path or backfeed. Also verify off-state isolation, leakage, absolute maximum signal limits, and the operating range for the exact ordering suffix.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The verified product information does not provide definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals statements for the exact MAX361CSE+ ordering suffix.

数据核验日期: 2026-11-09 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

MAX361CSE+ datasheet MAX361CSE+ pinout MAX361CSE+ datasheet pdf MAX361CSE+ equivalent MAX361CSE+ replacement MAX361CSE+ cross reference MAX361CSE+ vs MAX361ESE+ MAX361CSE+ vs MAX361CSE MAX361CSE+ 16-SOIC footprint Analog Devices MAX361CSE+ MAX361CSE+ analog switch application MAX361CSE+ price MAX361CSE+ stock

相关元器件 & 术语

Analog Devices MAX361CSE+ MAX361ESE+ MAX361CSE MAX361 MAX362 analog switch analog multiplexer SPST switch normally closed switch NC switch on resistance channel matching leakage current 16-SOIC SOIC package surface-mount package semiconductor signal routing test and measurement data acquisition sensor interface instrumentation amplifier communication equipment
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情