MC33390DR2 - J1850 Class B Half-Duplex Transceiver | NXP
料号: MC33390DR2 ✗ 停产MC33390DR2 概述
An automotive serial transceiver is an interface integrated circuit that connects a vehicle controller or diagnostic device to a physical communication bus. The MC33390DR2 belongs to the broader transceiver hierarchy: serial transceiver → network interface IC → interface IC → semiconductor. Unlike a general-purpose UART, which primarily converts parallel data into serial characters, a J1850 Class B transceiver also manages the electrical connection to the vehicle network through its driver and receiver functions.
The MC33390DR2 is intended for half-duplex operation, meaning the attached controller and bus share a bidirectional communication path. This topology simplifies node connection compared with separate transmit and receive channels. The manufacturer identifies the device as a Class B serial transceiver for the automotive SAE J1850 data communication network interface, making it applicable to legacy vehicle communication, service equipment, and diagnostic-interface designs that already use this network specification.
The datasheet block-diagram description identifies a voltage-regulator section, bus-driver section, and thermal-related content. Those functional blocks indicate that the device is more than a simple signal buffer. Nevertheless, detailed electrical limits, receiver thresholds, bus-driver output levels, and thermal-limit values must be taken from the manufacturer datasheet when designing a new circuit; those values should not be inferred from the general transceiver classification alone.
Typical uses include an automotive diagnostic connector interface, a J1850 service-tool adapter, an embedded vehicle module interface, and a half-duplex network test fixture. In each case, the controller must generate and interpret the J1850 physical-layer signaling, while the MC33390DR2 provides the connection between the controller and the Class B bus. Its 8-pin SOIC package supports compact surface-mount assembly and is convenient for mixed analog, power-management, and interface layouts.
For PCB implementation, use the exact pin-description and typical-application circuits in the manufacturer datasheet. Particular attention belongs to supply decoupling, bus connection protection, grounding, and the treatment of the bidirectional bus node. Avoid adding external components or protection networks that change bus rise time or signal levels without checking their effect on network operation.
This product record combines the verified device identity, package information, J1850 Class B function, half-duplex architecture, sourcing links, and practical implementation guidance. It also distinguishes confirmed manufacturer information from parameters that require the complete electrical characteristic table before schematic release or production qualification.
直接替换替代料: MC33390DR2 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MC33390DR2 (相同外形与封装尺寸) ——差异在于 Network Standard, Package, Product Type, Transceiver Configuration.
MC33390DR2 规格参数
| Product Type | J1850 Class B serial transceiver |
| Transceiver Configuration | 1/1 transceiver |
| Duplex Mode | Half-duplex |
| Network Standard | SAE J1850 Class B |
| 封装 | 8-pin SOIC |
| 安装类型 | Surface mount |
| Manufacturer | NXP Semiconductors |
| Original Manufacturer | Motorola, Inc. |
| Internal Voltage Regulator | Present |
| Integrated Bus Driver | Present |
| RoHS 状态 | Compliant |
MC33390DR2 8-pin soic 引脚配置指南
MC33390DR2(8-pin soic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MC33390DR2.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MC33390DR2 适用于 6 应用s: Automotive Diagnostic Interfaces, J1850 Service-Tool Adapters, Embedded Vehicle Module Interfaces, Half-Duplex Bus Test Fixtures, Legacy Vehicle Network Gateways, Automotive Communication Test Equipment.
Automotive Diagnostic Interfaces
The MC33390DR2 fits a J1850 Class B diagnostic interface because it provides a one-transceiver half-duplex connection to the SAE J1850 bus and is packaged in an 8-pin SOIC. It can sit between a vehicle controller and the physical bus rather than requiring separate transmit and receive channels. The implementation must follow the manufacturer’s bus-driver, receiver-threshold, supply, and grounding requirements. A diagnostic connector also needs protection appropriate to the vehicle environment, but that network interface should be reviewed separately from the transceiver’s own specifications.
推荐
J1850 Service-Tool Adapters
A J1850 service-tool adapter can use the MC33390DR2 as the physical-layer interface between processing electronics and a Class B vehicle network. Its half-duplex architecture supports a shared bidirectional bus path, while the internal voltage-regulator and bus-driver blocks simplify the analog interface arrangement compared with discrete driver circuitry. For dependable adapter operation, verify the device’s electrical thresholds and bus-drive limits against the complete datasheet, and define cable surge protection without degrading the required bus waveform.
推荐
Embedded Vehicle Module Interfaces
The MC33390DR2 is appropriate for legacy vehicle modules that expose a J1850 Class B connection while processing application data locally. A microcontroller or communications controller can communicate through the transceiver’s bidirectional, half-duplex path rather than driving the bus directly. The 8-pin SOIC format supports compact surface-mount placement, but board planning must reserve correct decoupling and grounding around the supply and regulator blocks. Firmware must also avoid protocols that assume simultaneous independent transmit and receive operation.
推荐
Half-Duplex Bus Test Fixtures
The MC33390DR2 can form the network-facing section of a bench fixture used to exercise legacy J1850 Class B communication. Its half-duplex behavior permits a compact fixture that connects to a shared bus path, and the integrated bus-driver and voltage-regulator functions reduce the number of separate analog blocks. Fixture accuracy depends on using characterized bus impedance, termination, power, and measurement points defined by the manufacturer documentation. The fixture should not be used as a substitute for a modern CAN or LIN analyzer.
推荐
Legacy Vehicle Network Gateways
A gateway for an older vehicle platform can use the MC33390DR2 when the legacy branch communicates through J1850 Class B. The transceiver handles the physical bus connection while higher-level electronics translate data between the legacy network and another interface. Because J1850 is half-duplex, the gateway must coordinate bus access and avoid simultaneous transmission conflicts. The device’s receiver thresholds, output levels, supply range, and thermal limits must be checked against the actual vehicle electrical environment before production use.
推荐
Automotive Communication Test Equipment
The MC33390DR2 is applicable to specialized test equipment intended for J1850 Class B systems because it is explicitly identified as a Class B serial transceiver with bidirectional half-duplex operation. Equipment designers can use the same integrated interface rather than recreating the bus-driver and receiver stages with discrete components. Calibration should account for the device’s documented receive thresholds, bus output behavior, supply conditions, and temperature limits. The equipment must also implement the J1850 protocol and timing above this physical-layer device.
推荐
推荐产品汇总
工程参考数据: MC33390DR2 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MC33390D |
|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC |
| Brand | NXP Semiconductors | NXP Semiconductors |
| Product Type | J1850 Class B serial transceiver | J1850 Class B serial transceiver |
| Duplex Mode | Half-duplex | Half-duplex |
| Network Support | SAE J1850 Class B | SAE J1850 Class B |
| Transceiver Count | 1/1 transceiver | 1/1 transceiver |
| Internal Voltage Regulator | Present | Present |
| Integrated Bus Driver | Present | Present |
关键差异点
- Purpose-built J1850 Class B interface (对比 MC1489NG4)
- Integrated voltage-regulator and bus-driver blocks (对比 Discrete J1850 bus interface)
- Exact same-family package compatibility (对比 MC33390D)
设计说明
Assign the PCB footprint from the exact 8-pin SOIC drawing associated with MC33390DR2, including lead pitch, body width, and land geometry. Do not rely on a generic SOIC-8 footprint without comparing manufacturer dimensions. Route the bidirectional bus as a controlled network node, keep it away from sensitive analog and clock traces, and provide the supply-decoupling arrangement shown in the manufacturer datasheet.
Confirm the external supply range, quiescent current, regulator behavior, and bus-driver load current in the manufacturer electrical-characteristics table before power-up. Place the required input capacitor at the supply pins with a short ground return, and calculate worst-case dissipation using the actual VIN, VOUT, bus duty cycle, and ambient temperature. The internal voltage-regulator block should not be interpreted as permission to exceed the documented supply limits.
Do not substitute the MC33390DR2 for a modern CAN, LIN, or other automotive transceiver merely because the package or interface category appears similar. The device targets the legacy J1850 Class B physical layer and uses bidirectional half-duplex communication. Also avoid adding bus termination, filtering, or protection parts without checking their effect on receiver thresholds, driver output levels, rise time, and network waveform integrity.
Separate the bus node from sensitive logic and route it away from high-current switching paths. Use a continuous or tightly connected ground reference beneath the device where the recommended layout permits, and minimize loop area around bus-driver and supply connections. For cables and diagnostic connectors, place appropriate protection at the connector boundary, then verify that the protection network does not compromise the transceiver’s specified bus behavior.
Thermal design should use the manufacturer’s maximum dissipation and thermal information together with the vehicle’s maximum ambient temperature. Account for bus-drive duty cycle because automotive network activity is intermittent and may vary with operating mode. Validate the PCB copper area, nearby heat sources, and enclosure temperature at the device rather than relying only on the ambient rating at the connector.
合规信息
RoHS compliance is indicated by the component-assembly listing. REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer’s current material or product documentation.