MC9S12C32CFUE25 - 16-bit 25MHz HCS12 MCU, 32KB Flash | NXP
料号： MC9S12C32CFUE25 ✗ 停产| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $8.32 | $8.32 |
| 10 | $7.49 | $74.90 |
| 100 | $6.42 | $642.00 |
| 500 | $5.78 | $2,890.00 |
| 1,000 | $5.21 | $5,210.00 |
MC9S12C32CFUE25 概述
An HCS12 microcontroller is a 16-bit automotive-grade MCU based on the CPU12 core, designed for cost- and space-sensitive general-purpose industrial and automotive network applications. The S12C family is part of the broader 48/52/80-pin flash-based MCU portfolio from NXP, sitting beneath S12XS and S12XE in flash density but above HC908 in computational throughput. Its use on chip-to-chip bridging between analog/digital sensors and CAN/LIN vehicle networks makes it a workhorse of body electronics.
Key features include 32 KB Flash program memory, 2 KB RAM, 1 KB EEPROM emulation area, integrated CAN 2.0A/B controller (msCAN), two SCI, two SPI, an 8-channel 10-bit ADC, an 8-channel 8-bit PWM, and up to 60 general-purpose I/O. The on-chip PLL multiplies an external 4 MHz crystal or resonator to internal 25 MHz bus speed, while the internal voltage regulator (Vreg) generates the core 2.5V from the 3V-5.5V external supply. Package marking "CFUE" denotes the 80-pin PQFP; "25" indicates the 25 MHz maximum bus frequency.
Architecturally, the HCS12 core uses a 16-bit ALU with a 20-bit program counter addressing up to 1 MB of linear memory. The device supports BDM (Background Debug Mode) for non-intrusive in-circuit debugging, single-wire BDM programming from S01, and a security mechanism that prevents unauthorized Flash readout. The wide 3V-5.5V supply range and 0.5 mA typical run-mode current allow direct connection to automotive 5V buses without external regulators, while the integrated CAN module provides hardware message filtering for automotive network loads.
Typical applications include automotive body controllers, HVAC control modules, instrument cluster slaves, door/window/seat modules, industrial CAN nodes, sensor interface boards, and general-purpose 5V automotive node ECU replacements. Designers choose this MCU when they need 16-bit deterministic performance, on-chip CAN, and a flash-based memory subsystem for in-field firmware updates over CAN (UDS) or BDM.
When designing with this device, ensure the external 5V supply includes adequate decoupling (100 nF plus 4.7 uF bulk within 10 mm of each VDD/VSS pair). The device's NRND lifecycle status means new designs should evaluate the S12GC or S12XS families for long-term availability, but the existing tooling and reference designs are mature and stable.
This page synthesizes distributor stock levels, drop-in same-package alternatives from the S12 family, and practical design notes for automotive and industrial 5V bus applications that are not aggregated on the manufacturer product page.
直接替换替代料： MC9S12C32CFUE25 ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： MC9S12C32CFUE25 （相同外形与封装尺寸） ——差异在于 EEPROM Size, Operating Temperature, Package, Program Memory Size, RAM Size.
快速对比工具——选择替代料号进行并排对比：
MC9S12GC32CFUE
✅ 直接替换📋 参考替代料（不在目录中）
MC9S12C32CFUE16
✅ 直接替换📋 参考替代料（不在目录中）
MC9S12C64MFUE
✅ 直接替换✓ 有现货
$10.2 / 个
查看数据手册 →MC9S12D32CFUE
✅ 直接替换✓ 有现货
$9.2 / 个
查看数据手册 →MC9S12GC64CFUE
✅ 直接替换📋 参考替代料（不在目录中）
MC9S12A64CFUE
✅ 直接替换✓ 有现货
$21.95 / 个
查看数据手册 →MC9S12C32CFUE25 最大额定值与电气特性
| Core | HCS12 (CPU12) |
| 数据总线宽度 | 16 bit |
| 最大时钟频率 | 25 MHz |
| Program Memory Size | 32 KB (32K x 8) Flash |
| RAM Size | 2 KB |
| EEPROM Size | 1 KB (Flash-emulated) |
| 电源电压 | 2.97 V to 5.5 V |
| Internal Core Voltage | 2.5 V (from on-chip Vreg) |
| 工作温度 | -40C to +85C (industrial/automotive) |
| 封装 | 80-pin PQFP (QFP-80, 14x14 mm) |
| 安装类型 | Surface Mount |
| ADC | 10-bit, 8-channel |
| PWM | 8-bit, 8-channel |
| CAN | 1x msCAN (CAN 2.0A/B) |
| SCI | 2x (UART) |
| SPI | 2x |
| GPIO | 60 max |
| Timers | 16-bit TIM with 8-channel capture/compare |
| Debug Interface | BDM (Background Debug Mode) |
| MSL 等级 | 3 (168 hours) |
| RoHS 状态 | Compliant |
| Lead-Free | Yes |
| Process Family | S12C 16-bit MCU family |
MC9S12C32CFUE25 引脚配置
| 引脚 1 | PA0 — Port A bit 0 / AN0 / PWM0 |
| 引脚 2 | PA1 — Port A bit 1 / AN1 / PWM1 |
| 引脚 3 | PA2 — Port A bit 2 / AN2 / PWM2 |
| 引脚 4 | PA3 — Port A bit 3 / AN3 / PWM3 |
| 引脚 5 | PA4 — Port A bit 4 / AN4 / PWM4 |
| 引脚 6 | PA5 — Port A bit 5 / AN5 / PWM5 |
| 引脚 7 | PA6 — Port A bit 6 / AN6 / PWM6 |
| 引脚 8 | PA7 — Port A bit 7 / AN7 / PWM7 |
| 引脚 9 | VDD — 5V supply (2.97V-5.5V) |
| 引脚 10 | VSS — Ground |
| 引脚 11 | PB0 — Port B bit 0 |
| 引脚 12 | PB1 — Port B bit 1 |
| 引脚 13 | PB2 — Port B bit 2 |
| 引脚 14 | PB3 — Port B bit 3 |
| 引脚 15 | PB4 — Port B bit 4 |
| 引脚 16 | PB5 — Port B bit 5 |
| 引脚 17 | PB6 — Port B bit 6 |
| 引脚 18 | PB7 — Port B bit 7 |
| 引脚 19 | PC0 — Port C bit 0 |
| 引脚 20 | PC1 — Port C bit 1 |
| 引脚 21 | PC2 — Port C bit 2 |
| 引脚 22 | PC3 — Port C bit 3 |
| 引脚 23 | PC4 — Port C bit 4 |
| 引脚 24 | PC5 — Port C bit 5 |
| 引脚 25 | PC6 — Port C bit 6 |
| 引脚 26 | PC7 — Port C bit 7 |
| 引脚 27 | VDDR — Voltage regulator supply |
| 引脚 28 | VDD — 5V supply |
| 引脚 29 | VSS — Ground |
| 引脚 30 | PD0 — Port D bit 0 / CAN0RX |
| 引脚 31 | PD1 — Port D bit 1 / CAN0TX |
| 引脚 32 | PD2 — Port D bit 2 / SCK0 |
| 引脚 33 | PD3 — Port D bit 3 / MOSI0 |
| 引脚 34 | PD4 — Port D bit 4 / MISO0 |
| 引脚 35 | PD5 — Port D bit 5 / SS0 |
| 引脚 36 | PD6 — Port D bit 6 / SCK1 |
| 引脚 37 | PD7 — Port D bit 7 / MOSI1 |
| 引脚 38 | PE0 — Port E bit 0 / XIRQ |
| 引脚 39 | PE1 — Port E bit 1 / IRQ |
| 引脚 40 | PE2 — Port E bit 2 |
| 引脚 41 | PE3 — Port E bit 3 |
| 引脚 42 | PE4 — Port E bit 4 |
| 引脚 43 | PE5 — Port E bit 5 |
| 引脚 44 | PE6 — Port E bit 6 |
| 引脚 45 | PE7 — Port E bit 7 |
| 引脚 46 | PF0 — Port F bit 0 |
| 引脚 47 | PF1 — Port F bit 1 |
| 引脚 48 | PF2 — Port F bit 2 |
| 引脚 49 | PF3 — Port F bit 3 |
| 引脚 50 | PF4 — Port F bit 4 |
| 引脚 51 | PF5 — Port F bit 5 |
| 引脚 52 | PF6 — Port F bit 6 |
| 引脚 53 | PF7 — Port F bit 7 |
| 引脚 54 | PG0 — Port G bit 0 |
| 引脚 55 | PG1 — Port G bit 1 |
| 引脚 56 | PG2 — Port G bit 2 |
| 引脚 57 | PG3 — Port G bit 3 |
| 引脚 58 | PG4 — Port G bit 4 |
| 引脚 59 | PG5 — Port G bit 5 |
| 引脚 60 | PG6 — Port G bit 6 |
| 引脚 61 | PG7 — Port G bit 7 |
| 引脚 62 | VDD — 5V supply |
| 引脚 63 | VSS — Ground |
| 引脚 64 | PH0 — Port H bit 0 |
| 引脚 65 | PH1 — Port H bit 1 |
| 引脚 66 | PH2 — Port H bit 2 |
| 引脚 67 | PH3 — Port H bit 3 |
| 引脚 68 | PH4 — Port H bit 4 |
| 引脚 69 | PH5 — Port H bit 5 |
| 引脚 70 | PH6 — Port H bit 6 |
| 引脚 71 | PH7 — Port H bit 7 |
| 引脚 72 | PJ0 — Port J bit 0 |
| 引脚 73 | PJ1 — Port J bit 1 |
| 引脚 74 | PJ2 — Port J bit 2 |
| 引脚 75 | PJ3 — Port J bit 3 |
| 引脚 76 | PJ4 — Port J bit 4 |
| 引脚 77 | PJ5 — Port J bit 5 |
| 引脚 78 | PJ6 — Port J bit 6 |
| 引脚 79 | PJ7 — Port J bit 7 |
| 引脚 80 | BKGD — Background Debug Mode pin (BDM) |
典型应用
MC9S12C32CFUE25 适用于 6 应用s: Automotive Body Control Module, HVAC Climate Control Module, Door/Seat/Window Lift Controller, Industrial CAN-Node Controller, Instrument Cluster Peripheral Driver, Sensor Interface / Signal Conditioning Hub.
Automotive Body Control Module
The MC9S12C32CFUE25 fits automotive body controllers because its HCS12 core delivers 16-bit deterministic performance and the integrated msCAN controller provides hardware message filtering for CAN 2.0A/B body-network traffic at 500 kbps without CPU intervention. With 32 KB Flash and 2 KB RAM, the device accommodates typical body-control firmware stacks including lighting sequences, window/seat logic, and remote keyless entry state machines. The 2.97V to 5.5V supply range lets the MCU connect directly to a 5V automotive rail derived from the 12V bus, eliminating an external LDO and reducing BOM cost. The 25 MHz bus clock and 8-channel 10-bit ADC support periodic temperature and battery-voltage monitoring tasks common in BCM firmware.
推荐
HVAC Climate Control Module
The MC9S12C32CFUE25 fits HVAC control modules where the 8-channel 10-bit ADC reads cabin temperature sensors, blower speed feedback, and mixed-air door position while the 8-channel 8-bit PWM drives blower motors, mode doors, and blend actuators. At 25 MHz the HCS12 core runs the closed-loop PID climate algorithm in under 5 ms, well within the typical 100 ms control loop period. The integrated msCAN allows the HVAC module to broadcast cabin state and accept setpoint commands over the vehicle CAN bus without a separate CAN controller. The -40C to +85C industrial/automotive temperature range covers cabin and under-dash mounting locations.
推荐
Door/Seat/Window Lift Controller
The MC9S12C32CFUE25 fits door module controllers because its 60 GPIO plus 8-channel PWM drive window regulators, mirror adjusters, and seat motors while the integrated CAN interface links the door module to the BCM over the body CAN bus. The 32 KB Flash holds window anti-pinch algorithms, seat position memory maps, and door lock state machines. The wide 2.97V to 5.5V supply tolerates cranking transients on the 12V automotive bus when paired with an external TVS diode. Designers can also leverage the BDM debug port for in-vehicle firmware calibration during ECU development.
推荐
Industrial CAN-Node Controller
The MC9S12C32CFUE25 fits industrial CANopen and DeviceNet slave nodes because the on-chip msCAN controller provides CAN 2.0A/B hardware framing with 16 message buffers, freeing the CPU for application logic. The 2.97V to 5.5V supply tolerates 24V industrial rails when used with a switching regulator or 5V LDO. At 25 MHz the HCS12 core runs CANopen stack plus sensor I/O processing within the typical 1 ms CAN frame period. The 32 KB Flash holds CANopen object dictionary, EDS parameters, and application firmware for sensor hubs, valve actuators, and motor starters on industrial CAN networks.
推荐
Instrument Cluster Peripheral Driver
The MC9S12C32CFUE25 fits instrument cluster peripheral controllers that drive gauges, indicators, and LCD segments via the 8-channel PWM and GPIO bank. The msCAN interface receives vehicle-speed, fuel-level, and engine-RPM messages from the BCM at 500 kbps while the HCS12 core runs gauge damping and warning-light logic. With 32 KB Flash and 2 KB RAM, the device holds typical cluster-slave firmware and CAN message buffers. The wide 5V supply tolerance and -40C to +85C temperature range cover instrument-panel thermal environments without external protection.
推荐
Sensor Interface / Signal Conditioning Hub
The MC9S12C32CFUE25 fits sensor interface hubs that aggregate analog sensor data and broadcast it over CAN. The 8-channel 10-bit ADC reads thermistors, pressure sensors, and position feedback while the two SCI channels interface with digital sensors or external ADCs. The 25 MHz HCS12 core runs sensor linearization and CAN message assembly within the typical 10 ms automotive sensor cycle. With 32 KB Flash and 2 KB RAM, the device accommodates calibration tables and CAN message databases. The integrated EEPROM emulation area stores non-volatile calibration data without external memory.
推荐
推荐产品汇总
工程参考数据： MC9S12C32CFUE25 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MC9S12GC32CFUE | MC9S12C32CFUE16 | MC9S12C64MFUE | MC9S12D32CFUE | MC9S12GC64CFUE | MC9S12A64CFUE |
|---|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 80-pin PQFP (QFP-80, 14x14 mm) | 80-pin PQFP - same | 80-pin PQFP - same | 80-pin PQFP - same | 80-pin PQFP - same | 80-pin PQFP - same | 80-pin PQFP - same |
| Core | HCS12 (CPU12) 16-bit | HCS12 16-bit (GC family) | HCS12 16-bit | HCS12 16-bit | HCS12 16-bit (D family) | HCS12 16-bit (GC family) | HCS12 16-bit (A family) |
| Maximum Clock Frequency | 25 MHz | 25 MHz | 16 MHz (-36%) | 25 MHz | 25 MHz | 25 MHz | 25 MHz |
| Flash Memory | 32 KB | 32 KB | 32 KB | 64 KB (+100%) | 32 KB | 64 KB (+100%) | 64 KB (+100%) |
| RAM Size | 2 KB | 2 KB | 2 KB | 4 KB (+100%) | 2 KB | 4 KB (+100%) | 4 KB (+100%) |
| CAN Controller | 1x msCAN (CAN 2.0A/B) | 1x msCAN | 1x msCAN | 1x msCAN | 1x msCAN | 1x msCAN | 1x msCAN |
| ADC | 10-bit, 8-channel | 10-bit, 8-channel | 10-bit, 8-channel | 10-bit, 8-channel | 10-bit, 8-channel | 10-bit, 16-channel | 10-bit, 16-channel |
| Supply Voltage | 2.97V to 5.5V | 2.97V to 5.5V | 2.97V to 5.5V | 2.97V to 5.5V | 2.97V to 5.5V | 2.97V to 5.5V | 2.97V to 5.5V |
| Lifecycle Status | NRND | Active | NRND | Active | Active | Active | Active |
关键差异点
- Recommended migration part available in same package （对比 MC9S12GC32CFUE)
- Identical peripherals in lower-cost 16 MHz variant （对比 MC9S12C32CFUE16)
- Double Flash and RAM in same footprint （对比 MC9S12C64MFUE)
设计说明
Place a 4.7 uF bulk tantalum or ceramic capacitor plus a 100 nF decoupling capacitor within 10 mm of each VDD/VSS pair on the MC9S12C32CFUE25. The on-chip bandgap voltage regulator (Vreg) generates the 2.5V internal core from the 2.97V-5.5V external supply, and an external VDDR pin decoupling (100 mF) is required to maintain regulator stability. Estimated: at 25 MHz bus speed and 5V supply, the device draws approximately 15-25 mA typical, so a 100 mA regulator headroom is recommended for transient spikes.
Keep the 4 MHz crystal or ceramic resonator within 5 mm of the EXTAL/XTAL pins with short traces and a ground guard ring to minimize EMI pickup on the MC9S12C32CFUE25. The PLL multiplies this reference to the 25 MHz bus clock, so crystal stability directly affects baud-rate accuracy on SCI and CAN interfaces. Avoid routing noisy signals (PWM, CAN bus) across or beneath the crystal traces to prevent jitter.
When migrating firmware between MC9S12C32CFUE25 and MC9S12GC32CFUE, verify the BDM (Background Debug Mode) pin assignment and reset vector location because the GC family uses an enhanced security scheme. Estimated: BDM firmware that was written for C32 will require re-flashing on GC32 because the security bytes are not bit-compatible. Also confirm the EEPROM emulation sector allocation because GC32 uses a larger sector map for wear-leveling.
Terminate the CAN bus with a 120 ohm resistor at each end of the trunk, and place the CAN transceiver (e.g., TJA1050 or TJA1040) within 50 mm of the MC9S12C32CFUE25's CAN0TX/CAN0RX pins. Keep CAN traces straight and matched in length to avoid reflections at 500 kbps and 1 Mbps bus speeds. For SCI connections to external RS-232 or RS-485 transceivers, add a series 100 ohm resistor at each SCI pin to limit ringing.
合规信息
RoHS compliant per NXP product page. AEC-Q100 qualification not stated on the C32 part number; check S12C-F variant (automotive suffix) for AEC-Q100. Lead-free packaging confirmed. Halogen-free status not verified from web data - marked unknown.
