MPC8347ZQADDB - PowerQUICC II Pro 266MHz SoC, 620-PBGA | NXP
料号： MPC8347ZQADDB ✓ 量产中MPC8347ZQADDB 概述
A PowerQUICC II Pro processor is a system-on-chip (SoC) line from NXP (formerly Freescale) that integrates a PowerPC e300 core with communications-specific peripherals. It belongs to the broader category of communications processors -> embedded microprocessors -> microcontrollers and MPUs -> integrated circuits. PowerQUICC II Pro parts are descendants of the original PowerQUICC family and are commonly deployed in networking, storage, and industrial control equipment where deterministic communications performance is required.
Key specifications include a 266 MHz core frequency, 0.13 um process technology, multi-voltage rails at 1.8 V, 2.5 V, and 3.3 V, and a 620-pin plastic BGA package measuring 29 mm by 29 mm. The integrated peripheral set supports DDR1/DDR2 memory, a 32-bit PCI interface, one Gigabit Ethernet MAC, USB 2.0, and dedicated security acceleration hardware. Industrial temperature grade (0 to 105C) supports deployment in thermally challenging environments without active cooling.
From an architectural standpoint, the e300 core is a superscalar PowerPC implementation with separate 16 KB instruction and 16 KB data L1 caches, dual issue, and out-of-order execution. The communications engine (QUICC Engine) provides hardware-accelerated protocol termination for Ethernet, HDLC, and other serial protocols. The combination enables the MPC8347ZQADDB to perform both control-plane processing and data-plane protocol handling concurrently.
Typical applications include industrial Ethernet switches, secure routers, DSLAM line cards, network attached storage (NAS) controllers, and factory automation gateways. The integrated Gigabit Ethernet and PCI interfaces also suit the part for PCI-based peripheral cards and custom networking appliances. Industrial grade silicon ensures reliability in extended-temperature installations.
When designing with this part, allocate sufficient PCB area for the 29x29 mm BGA and use at least six PCB layers with continuous power and ground planes for signal integrity. Ensure junction temperature does not exceed rated limits under maximum load by using thermal vias beneath the exposed die pad and verifying the thermal management envelope with manufacturer-supplied thermal models.
This page synthesizes distributor pricing, package-aware drop-in alternatives (including MPC8343/MPC8347 family variants), and practical design notes that go beyond the manufacturer datasheet to support BOM decisions for new designs and legacy maintenance.
直接替换替代料： MPC8347ZQADDB ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： MPC8347ZQADDB （相同外形与封装尺寸） ——差异在于 Core Architecture, Ethernet, Memory Controller, Operating Temperature, USB.
MPC8347EZQAGDDB
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
MPC8347CVVAGDDB
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
MPC8347ZQAGDDB
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
MPC8343CVRADDB
✅ 直接替换联系询价
查看数据手册 →MPC8343EVRADDB
✅ 直接替换联系询价
查看数据手册 →MPC8358CVRAGDGA
✅ 直接替换📋 参考替代料（不在目录中）
MPC8347ZQADDB 最大额定值与电气特性
| Manufacturer | NXP Semiconductors (formerly Freescale) |
| Series | PowerQUICC II Pro (MPC83xx) |
| Core Architecture | PowerPC e300 |
| Core Count | 1 |
| 数据总线宽度 | 32-bit |
| Maximum Core Frequency | 266 MHz |
| Process Technology | 0.13 um CMOS |
| 电源电压 | 1.8 V / 2.5 V / 3.3 V |
| 封装 | 620-PBGA (29x29 mm) |
| Memory Controller | DDR1 / DDR2 |
| PCI Interface | 32-bit PCI |
| Ethernet | 1x Gigabit Ethernet |
| USB | USB 2.0 |
| 工作温度 | 0C to +105C (industrial grade) |
| 安装类型 | Surface Mount (PBGA) |
MPC8347ZQADDB 620-pbga (29x29 mm) 引脚配置指南
MPC8347ZQADDB（620-pbga (29x29 mm) 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： MPC8347ZQADDB.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MPC8347ZQADDB 适用于 6 应用s: Industrial Ethernet Switch, Secure Router / VPN Gateway, DSLAM Line Card, Network Attached Storage (NAS) Controller, Industrial Automation Gateway, PCI-based Custom Peripheral Card.
Industrial Ethernet Switch
The MPC8347ZQADDB fits industrial Ethernet switch designs because its integrated Gigabit Ethernet MAC and QUICC Engine hardware-accelerated protocol termination offload packet processing from the e300 CPU. At 266 MHz the e300 core can run a real-time Linux or VxWorks control plane while the QUICC Engine handles line-rate Ethernet bridging, VLAN tagging, and IGMP snooping. The 0 to 105C industrial temperature grade supports deployment in factory-floor enclosures, and the 32-bit PCI bus enables expansion to additional PHYs or switch fabrics. Designers place the device on a six-layer PCB with continuous ground planes beneath the 29x29 mm BGA to maintain signal integrity on DDR2 and Gigabit Ethernet traces.
推荐
Secure Router / VPN Gateway
The MPC8347ZQADDB is well suited for secure router platforms thanks to its integrated security acceleration on the MPC8347E family and its Gigabit Ethernet plus USB 2.0 peripheral set. At 266 MHz the e300 core handles routing table lookups and control-plane processing while dedicated hardware engines accelerate IPsec, SSL/TLS, and MACsec without CPU bottlenecks. The 620-PBGA footprint suits mid-density router line cards with adequate PCB area for high-speed SERDES routing. Power sequencing across 1.8 V, 2.5 V, and 3.3 V rails must follow NXP's reference design to keep DDR2 interface timing within JEDEC specifications during cold-start VPN handshake loads.
推荐
DSLAM Line Card
The MPC8347ZQADDB works in DSLAM line cards because its e300 core combined with the QUICC Engine can terminate ATM, HDLC, and Ethernet protocols on a per-subscriber basis. Its 266 MHz CPU performs upstream queueing and traffic shaping while the hardware accelerator handles AAL2/AAL5 segmentation, leaving headroom for QoS policy enforcement. The DDR2 controller supports the cell-buffer memory required for upstream bursting on ADSL2+ and VDSL2 ports. The 620-PBGA package and 105C temperature rating suit the dense, warm line-card environment of central-office DSLAM shelves. JTAG and boundary-scan support simplify board-level bring-up during manufacturing test.
推荐
Network Attached Storage (NAS) Controller
The MPC8347ZQADDB serves as a NAS controller because its DDR2 memory controller, Gigabit Ethernet, and PCI bus together enable connection to SATA disk controllers and 1 GbE network ports from a single chip. The e300 core runs embedded Linux with SMB/CIFS, NFS, and iSCSI target stacks while the QUICC Engine accelerates TCP/IP offload for sustained file-transfer throughput. Storage management features such as RAID coordination and SMART monitoring run on the 266 MHz CPU with adequate headroom for typical four-bay NAS enclosures. The 105C industrial temperature grade supports fanless enclosure designs for small-office NAS products.
推荐
Industrial Automation Gateway
The MPC8347ZQADDB fits industrial automation gateways because it bridges fieldbus protocols (PROFIBUS, Modbus, CAN) on the PCI/serial side with Ethernet on the Gigabit Ethernet MAC, using the e300 core as a protocol-translation engine. The 0 to 105C industrial temperature rating supports deployment in cabinet-free factory environments and outdoor enclosures, while the wide voltage-rail tolerance (1.8 V, 2.5 V, 3.3 V) simplifies integration with industrial 24 V power systems via standard PMICs. Real-time determinism comes from the QUICC Engine's hardware-protocol timers running independently of the e300 core's interrupt latency.
推荐
PCI-based Custom Peripheral Card
The MPC8347ZQADDB suits PCI peripheral cards in industrial PCs because its 32-bit PCI interface allows it to operate as an intelligent co-processor on a standard PCI bus. The e300 core handles custom real-time DSP-style processing or specialized I/O while the host CPU runs general-purpose workloads. The 620-PBGA package, while large, is manageable on full-length PCI cards and supports the full industrial temperature range required for medical imaging, test-and-measurement, and machine-vision cards. Designers can leverage NXP's PCI reference schematics to minimize bring-up time when prototyping a custom PCI endpoint.
推荐
推荐产品汇总
工程参考数据： MPC8347ZQADDB ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MPC8347EZQAGDDB | MPC8347CVVAGDDB | MPC8347ZQAGDDB | MPC8343CVRADDB | MPC8343EVRADDB | MPC8358CVRAGDGA |
|---|---|---|---|---|---|---|---|
| Package | 620-PBGA (29x29) | 620-PBGA (29x29) - same | 620-PBGA (29x29) - same | 620-PBGA (29x29) - same | 620-PBGA (29x29) - same | 620-PBGA (29x29) - same | 620-PBGA (29x29) - same |
| Brand | NXP Semiconductors | NXP Semiconductors - same | NXP Semiconductors - same | NXP Semiconductors - same | NXP Semiconductors - same | NXP Semiconductors - same | NXP Semiconductors - same |
| Core Frequency | 266 MHz | Up to 400 MHz | 266 MHz | 266 MHz | 266 MHz | 266 MHz | Up to 400 MHz |
| Security Engine | Not enabled (ZQADDB variant) | Enabled (E variant) | Not enabled | Not enabled | Not enabled | Enabled (E variant) | Enabled (E variant) |
| Gigabit Ethernet | 1x GbE | 1x GbE | 1x GbE | 1x GbE | Not integrated | Not integrated | 2x GbE |
| Memory Interface | DDR1/DDR2 | DDR1/DDR2 | DDR1/DDR2 | DDR1/DDR2 | DDR1/DDR2 | DDR1/DDR2 | DDR2 |
| Operating Temperature | 0C to +105C | 0C to +105C | -40C to +105C | 0C to +105C | 0C to +105C | -40C to +105C | 0C to +105C |
| PCI Interface | 32-bit PCI | 32-bit PCI | 32-bit PCI | 32-bit PCI | 32-bit PCI | 32-bit PCI | 32-bit PCI + PCI Express |
关键差异点
- Integrated Gigabit Ethernet plus QUICC Engine hardware protocol accelerator （对比 MPC8343CVRADDB)
- Security engine option in same family for IPsec/SSL offload （对比 MPC8347ZQAGDDB)
- Higher performance upgrade path to 400 MHz MPC8358 family in same package （对比 MPC8358CVRAGDGA)
设计说明
The 620-PBGA (29x29 mm) package demands at least a six-layer PCB with continuous ground and power planes directly beneath the BGA. Use 0.8 mm ball pitch escape routing with microvias (laser-drilled, 0.1 mm via pad) for inner rows; standard through-vias cannot escape the inner balls without dog-bone fanouts that consume excessive routing channels. Maintain 50 ohm single-ended impedance on DDR2 traces and 100 ohm differential on PCI clock pairs; place a reference plane at least 8 mils below the top microstrip layer for controlled impedance.
The e300 core running at 266 MHz with full peripheral activity draws approximately 1.5 to 2.0 W. Use NXP's thermal model document to estimate theta_JA on your specific PCB stack-up; a four-layer board typically yields theta_JA around 18 to 22 C/W while a six-layer board with thermal vias drops this to 12 to 15 C/W. For fanless industrial enclosures, place a 30 mm x 30 mm copper pour on the top layer directly under the package and stitch thermal vias on a 1.2 mm grid through to the bottom-layer ground plane.
Do not skip the DDR2 write-leveling and read-gate-training sequence during boot; the MPC8347ZQADDB's DDR2 controller requires firmware-driven calibration for proper operation at 266 MHz. Power-rail sequencing must follow NXP's documented order (1.8 V core before 2.5 V before 3.3 V) with monotonic ramp times; out-of-order ramp can trigger ESD protection latch-up. Ensure JTAG TRST is held low during power-up and that the 266 MHz system clock has less than 50 ppm frequency error to avoid USB and Ethernet timing-margin violations.
合规信息
Compliance status for the MPC8347ZQADDB not confirmed in verified distributor data; consult NXP product compliance documentation or request a RoHS/REACH declaration through the manufacturer's support channel. AEC-Q100 not applicable - this part is an industrial-grade communications SoC, not an automotive-qualified MCU.
