MPC8360ZUALFHA - PowerQUICC II Pro, e300, 667 MHz MPU | NXP
料号： MPC8360ZUALFHA ✓ 量产中MPC8360ZUALFHA 概述
A PowerQUICC II Pro processor is a system-on-chip designed for wired and wireless communications infrastructure, combining a Power Architecture CPU core with specialised communications peripherals. The e300 core family evolved from the classic PowerQUICC II line and adds enhanced peripheral integration, allowing OEMs to reduce component count in routers, DSLAMs, media gateways, and industrial control equipment. The MPC8360 family supports revision 2.x of the silicon, which improves the DDR memory controller and adds hardware acceleration blocks used for protocol termination.
Key features of the MPC8360ZUALFHA include the e300 core with 32 KB instruction and data L1 caches, a 333 MHz local bus, dual 10/100/1000 Ethernet MACs, a 32-bit/66 MHz PCI controller, USB 2.0 (Full/Low speed), a security engine (SEC 2.0), and four TDM/ATM serial interfaces. The integrated DDR1/DDR2 memory controller with ECC supports up to 2 GByte of addressable memory, and the QUICC Engine multi-channel peripheral handles up to 64 HDLC or transparent channels per port. The device operates from a 1.2 V core supply with 3.3 V I/O, and the 740-pin TBGA package provides the signal density required for the wide peripheral set.
Technical depth: The e300 core implements the Power Architecture 32-bit instruction set and supports out-of-order execution pipelines tailored to communications workloads. The QUICC Engine runs as a microcoded RISC engine that offloads protocol processing from the CPU, freeing the e300 core for control plane and management tasks. The memory subsystem includes a 256 KB internal SRAM that can be configured as L2 cache or as a packet buffer.
Typical applications include enterprise routers and switches, DSL and cable modem termination equipment, media gateways, industrial Ethernet gateways, network-attached storage controllers, and PCI-based communications boards. The combination of PCI, Gigabit Ethernet, and the QUICC Engine makes the MPC8360 particularly well suited to multi-service access platforms that must terminate both legacy TDM traffic and packet-based services.
When designing with the MPC8360ZUALFHA, careful attention must be paid to the power supply decoupling network, signal integrity on the DDR memory bus, and the TBGA layout requiring microvia or wire-bond-compatible PCB technology. Designers should consult the NXP hardware specifications document for the full ball-map, thermal design recommendations, and reference schematics.
This page synthesises distributor pricing, drop-in alternatives from the same NXP family, and practical design notes beyond what the manufacturer datasheet alone provides, helping procurement and hardware engineers evaluate the part quickly.
直接替换替代料： MPC8360ZUALFHA ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
MPC8360VVALFHA
✅ 直接替换📋 参考替代料（不在目录中）
MPC8360EZUAGLF
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
MPC8358EALFJA
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
MPC8360ECZUAGLF
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
MPC8360CZUAJFA
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
MPC8568ECMWAGLF
✅ 直接替换📋 参考替代料（不在目录中）
MPC8360ZUALFHA 最大额定值与电气特性
| Architecture | PowerPC e300 (Power Architecture technology) |
| Core Family | PowerQUICC II Pro MPC83xx |
| Number of Cores | 1 |
| 数据总线宽度 | 32-bit |
| Maximum Core Frequency | 667 MHz |
| Core Supply Voltage | 1.2 V |
| I/O Supply Voltage | 3.3 V |
| Package Type | TBGA-740 (1.0 mm pitch, 37.5 x 37.5 mm, 1.46 mm height) |
| Package Style Code | LBGA / T-BGA |
| 工作温度范围 | 0 °C to +105 °C (commercial range per option code, non-encryption variant) |
| L1 Cache | 32 KB instruction + 32 KB data |
| L2 Cache / Internal SRAM | 256 KB (configurable) |
| Memory Controller | DDR1 and DDR2 with ECC, up to 2 GByte |
| Ethernet MAC | 2 x 10/100/1000 Mbps (GMII / TBI) |
| PCI Interface | 32-bit, 66 MHz PCI 2.3 |
| USB Interface | USB 2.0 Full/Low Speed |
| Serial Interfaces | QUICC Engine TDM / ATM, 4 x SERDES / TDM ports |
| Security Engine | SEC 2.0 (DES, 3DES, AES, SHA-1, MD-5, RSA) |
| 安装类型 | Surface Mount |
| RoHS 状态 | Compliant |
MPC8360ZUALFHA lbga / t-bga 引脚配置指南
MPC8360ZUALFHA（lbga / t-bga 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： MPC8360ZUALFHA.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MPC8360ZUALFHA 适用于 7 应用s: Enterprise Routers and Edge Gateways, DSLAM / Multi-Service Access Platform, Industrial Ethernet Gateway and Protocol Converter, Network-Attached Storage (NAS) Controller, PCI-Based Communications / Media Board, Voice-over-IP and Media Gateway SoC, Secure VPN Concentrator Head-End (Variant Select).
Enterprise Routers and Edge Gateways
The MPC8360ZUALFHA's 667 MHz e300 core plus dual Gigabit Ethernet MACs and a hardware QUICC Engine make it well suited to enterprise router and edge-gateway designs. The processor can terminate WAN interfaces (T1/E1 via TDM) while the integrated GbE MACs and PCI interface drive the LAN side and expansion slots. Compared with a discrete CPU-plus-network processor design, the MPC8360ZUALFHA collapses two chips into one package, reducing PCB area and BOM cost. Recommended companion parts include a Vitesse or Broadcom GbE PHY for each MAC, an external DDR2 buffer, and a CPLD for board-level glue logic.
推荐
DSLAM / Multi-Service Access Platform
DSLAMs and multi-service access platforms rely on the QUICC Engine's multi-channel HDLC support to terminate hundreds of subscriber lines without burdening the host CPU. The MPC8360ZUALFHA delivers this capability while exposing PCI and GbE uplinks for backhaul to the central office. With up to 4 GByte of addressable memory, the platform can host a real-time OS and full routing stack on a single MPC8360ZUALFHA. Use the part's hardware ECC support on the DDR2 interface to ensure long-term reliability on always-on infrastructure.
推荐
Industrial Ethernet Gateway and Protocol Converter
In factory and substation automation, the MPC8360ZUALFHA acts as a protocol converter between legacy fieldbuses (e.g. Profibus via TDM/HDLC) and modern Ethernet/IP networks. Its extended temperature range (0 to +105 °C) supports deployment inside unventilated enclosures, and the PCI interface enables add-in cards for proprietary fieldbus transceivers. Compared with a low-end MCU, the MPC8360ZUALFHA delivers the deterministic throughput required for fast EtherNet/IP cycle times.
推荐
Network-Attached Storage (NAS) Controller
The MPC8360ZUALFHA is used in mid-range RAID/NAS controllers where the host CPU offloads disk I/O via PCI and serves GbE to clients. The e300 core plus DDR2 controller delivers the throughput needed for SMB/NFS file serving, while the USB 2.0 port supports external backup devices. The 256 KB internal SRAM provides a fast buffer for caching directory metadata. Place a lithium-ion battery-backed RTC module nearby for timestamping on journaled file systems.
推荐
PCI-Based Communications / Media Board
When used as a PCI target on a host CPU's expansion bus, the MPC8360ZUALFHA becomes a flexible co-processor card for media gateways and software-defined networking appliances. The host CPU runs the data plane while the MPC8360ZUALFHA terminates TDM/ATM or offloads security via the QUICC Engine. The PCI 2.3 bus (32-bit at 66 MHz) provides more than 2 Gbit/s of bandwidth, sufficient for full-duplex T1/E1 and small SS7 link sets.
推荐
Voice-over-IP and Media Gateway SoC
VoIP and media gateways use the MPC8360ZUALFHA's QUICC Engine to handle PSTN signalling while the e300 core runs the SIP/RTP stack on top of a Linux or VxWorks BSP. Hardware echo-cancellation support and the SEC 2.0 engine (when enabled on the VV variant) accelerate SRTP encryption. With its TBGA-740 package providing 16 dedicated serial channels, a single MPC8360ZUALFHA can terminate a medium-density T1 or E1 trunk.
推荐
Secure VPN Concentrator Head-End (Variant Select)
While the MPC8360ZUALFHA itself has SEC disabled, the same PCB layout supports the MPC8360VVALFHA for VPN head-end designs. The VVALFHA share s the TBGA-740 footprint, so manufacturing lines can populate either part depending on the SKU. The 667 MHz e300 handles IKE / IPsec control plane processing, while the SEC engine accelerates bulk AES / 3DES / SHA-1 in the data plane. An external tamper-detection chip is recommended for FIPS 140-2 deployments.
推荐
推荐产品汇总
工程参考数据： MPC8360ZUALFHA ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MPC8360VVALFHA | MPC8360EZUAGLF | MPC8358EALFJA | MPC8360ECZUAGLF | MPC8360CZUAJFA | MPC8568ECMWAGLF |
|---|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | TBGA-740 (37.5 x 37.5 mm, 1.0 mm pitch) | TBGA-740 - same | TBGA-740 - same | TBGA-740 - same | TBGA-740 - same | TBGA-740 - same | TBGA-780-compatible footprint |
| Core Architecture | PowerPC e300 | PowerPC e300 | PowerPC e300 | PowerPC e300 | PowerPC e300 | PowerPC e300 | PowerPC e500 (newer generation) |
| SEC Engine | Disabled (ZU prefix) | Enabled (VV prefix) | Disabled | Enabled (standard for MPC8358E) | Disabled | Disabled | Enabled |
| Memory Interface | DDR1/DDR2 with ECC | DDR1/DDR2 with ECC | DDR1/DDR2 with ECC | DDR1/DDR2 with ECC | |||
| Ethernet MACs | 2 x 10/100/1000 | 2 x 10/100/1000 | 1 x 10/100/1000 | Multiple SERDES lanes | |||
| Pin/Ball Count | 740 | 740 | 740 | 740 | 740 | 740 | 780 |
| Lifecycle Status | Active | Active | Active | Mature - check NXP PCN |
关键差异点
- Encryption engine can be field-selected via part variant (pin-compatible ZU/VV siblings) （对比 MPC8360VVALFHA)
- Dual Gigabit Ethernet MACs on a single chip （对比 MPC8358EALFJA)
- Integrated QUICC Engine offloads HDLC/ATM from the host CPU （对比 MPC8568ECMWAGLF)
- Mature TBGA-740 footprint with extensive reference designs （对比 MPC8568ECMWAGLF)
设计说明
The MPC8360ZUALFHA requires two primary rails: a 1.2 V core supply and a 3.3 V I/O supply, plus a 2.5 V supply for the DDR2 memory interface when using DDR2 chips (1.8 V for DDR1). Estimated: at 667 MHz and full utilisation, the core power is in the 2-3 W range and the DDR2 I/O adds another ~0.5 W under burst traffic. Use a multi-phase buck controller such as a MAX1543 plus adequate bulk + ceramic decoupling; place 10 µF and 0.1 µF pairs as close as possible to each power ball, per NXP hardware specifications.
The TBGA-740 package at 1.0 mm pitch requires microvia PCB technology (laser-drilled vias in the BGA land pad) or via-in-pad with epoxy fill and planarisation. Designers without microvia capability should use a four-layer fanout with 0.4 mm trace/space and 0.2 mm via-pad geometry. Route the DDR2 byte lanes with matched length within ±25 mil and target a 50 Ω single-ended impedance; impedance mismatch on the DDR bus is the number-one root cause of memory errors on PowerQUICC II Pro hardware.
Although the part operates up to 105 °C junction temperature, the TBGA-740 package requires a thermal pad on the top side of the PCB to dissipate the 2-3 W core power. Estimated: with no heatsink and adequate top-side copper (>= 2 sq.in.), junction-to-ambient θJA is roughly 12-15 °C/W, meaning the die self-heats 30-45 °C above ambient at full load. Add a 4-layer inner-plane copper spreader and thermal vias through the BGA's central ball grid for production designs.
Do not confuse the ZU (security disabled) and VV (security enabled) variants when ordering - the MPC8360ZUALFHA cannot be upgraded to SEC functionality by firmware. Also note that the MPC8360 family is a discontinued Power Architecture platform per recent NXP product change notices; new designs should evaluate the MPC8568 family or NXP QorIQ Layerscape LS10xx for the long-term roadmap. Finally, leave TEST and JTAG balls connected per the reference design - removing them disables boundary-scan and complicates failure analysis.
The two Gigabit Ethernet MACs use GMII or TBI signalling, both of which are parallel buses operating at 125 MHz. Keep the GMII bus traces matched within 50 mil total length and isolate them from the DDR2 bus to avoid coupling. Place the 1.5 kV isolation magnetics module within 100 mm of the PHY, and add a common-mode choke if the design must pass IEC 61000-4-2 surge tests on the RJ-45 connector.
合规信息
RoHS compliant per NXP product page. AEC-Q100 not applicable - this is a communications MPU with industrial/extended temperature ranges, not an automotive-grade part. NXP recommends the MPC8360EEC/MPC8358EEC variants for harsher temperature ranges.
