MPC8548PXATGD - PowerPC e500 MPU 1.2GHz 783-FCPBGA | NXP
料号： MPC8548PXATGD ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $285 | $285.00 |
| 10 | $268.5 | $2,685.00 |
| 100 | $245 | $24,500.00 |
| 500 | $225 | $112,500.00 |
| 1,000 | $208 | $208,000.00 |
MPC8548PXATGD 概述
A PowerQUICC III microprocessor is a system-on-chip (SoC) built on the scalable e500 platform, combining a high-performance Power Architecture core with a flexible peripheral set. Within the broader hierarchy, the MPC8548 sits at the MPU (microprocessor unit) tier, above microcontrollers and below application processors, and is intended for fanless or lightly-cooled router/switch line cards, baseband offload, and storage controllers where deterministic integration matters more than graphics or application workload throughput.
Key features include a 1.2 GHz core frequency, integrated 32-bit DDR2 SDRAM controller with ECC support, hardware-accelerated cryptography, four GbE MACs, multiple PCI/PCI-X/PCIe controllers, and Serial RapidIO. The 783-pin FCPBGA package is specified for the commercial 0C to 105C operating range. The part runs from 1.0V core / 1.8V / 2.5V / 3.3V I/O rails.
Architecturally, the e500 core uses a 7-stage integer pipeline with a Book-E enhanced Power Architecture ISA, dual-issue dispatch, and dedicated L1 instruction and data caches. The integrated peripheral set reduces external component count compared with discrete CPU-plus-Northbridge designs of equivalent vintage, while the FC-PBGA die-down package exposes the die directly to the PCB for thermal dissipation at moderate power envelopes.
Typical applications include multiservice routers, edge routers, DSLAM line cards, SAN controllers, secure communication gateways, and industrial control. The combination of GSoPC and deterministic interrupt response makes it a fit for protocol-plane packet processing. In wireless base stations, the device handles MAC scheduling while paired with a DSP performs PHY.
When designing with this part, allocate a minimum 6-layer PCB with continuous power and ground planes, follow NXP AN3665 layout guidance, and ensure the thermal pad has at least a 6x6 via array stitched to internal ground. Decoupling must follow the reference schematic in the MPC8548 hardware specifications; do not omit the DDR2 VTT termination.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers shorten evaluation cycles and avoid common pitfalls.
直接替换替代料： MPC8548PXATGD ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： MPC8548PXATGD （相同外形与封装尺寸） ——差异在于 Memory Controller, Operating Temperature, Package, Mounting Type, RoHS Status.
快速对比工具——选择替代料号进行并排对比：
MPC8548PXAUVD
✅ 直接替换📋 参考替代料（不在目录中）
MPC8548PXAUPE
✅ 直接替换📋 参考替代料（不在目录中）
MPC8548PXATGB
✅ 直接替换📋 参考替代料（不在目录中）
MPC8548VTAQGD
✅ 直接替换✓ 有现货
$98.75 / 个
查看数据手册 →MPC8545PXATGD
✅ 直接替换📋 参考替代料（不在目录中）
MPC8548PXAQGD
✅ 直接替换✓ 有现货
$171 / 个
查看数据手册 →MPC8548PXATGD 最大额定值与电气特性
| Manufacturer | NXP Semiconductors (formerly Freescale) |
| Series | MPC85xx PowerQUICC III |
| Core | PowerPC e500 |
| Architecture | Power Architecture Book-E |
| Number of Cores | 1 |
| 数据总线宽度 | 32-bit |
| Core Frequency | 1.2 GHz |
| 工作温度 | 0C to +105C |
| 封装 | 783-FCPBGA (29x29) |
| 安装类型 | Surface Mount |
| 电源电压 | 1.0V core / 1.8V / 2.5V / 3.3V I/O |
| Memory Controller | 32-bit DDR2 SDRAM with ECC |
| Ethernet | 4x Gigabit Ethernet MACs |
| PCI Interfaces | PCI, PCI-X, PCI Express |
| Serial Interfaces | Serial RapidIO (SRIO) |
| Process Technology | 0.09 um CMOS |
| RoHS 状态 | Compliant |
MPC8548PXATGD 783-fcpbga (29x29) 引脚配置指南
MPC8548PXATGD（783-fcpbga (29x29) 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： MPC8548PXATGD.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MPC8548PXATGD 适用于 6 应用s: Multiservice Edge Router, Wireless Base Station Baseband, Storage Area Network (SAN) Controller, Secure Communication Gateway, DSLAM / Carrier Ethernet Line Card, Industrial Control and Automation.
Multiservice Edge Router
The MPC8548PXATGD fits multiservice edge routers thanks to its 4 integrated Gigabit Ethernet MACs, PCI Express, and hardware-accelerated packet processing. Its 1.2 GHz e500 core achieves wire-speed forwarding on small packets while the integrated crypto engine handles IPsec, SSL, and MACsec without external accelerators. Compared to discrete CPU-plus-Northbridge designs, the integrated peripheral set reduces BOM and PCB area by 30-40% while preserving deterministic interrupt latency critical for QoS scheduling. The 783-FCPBGA package enables 6-layer PCB integration with full thermal headroom.
推荐
Wireless Base Station Baseband
The MPC8548PXATGD suits wireless base station baseband processing where deterministic real-time response and Serial RapidIO links to DSPs are required. Its 1.2 GHz e500 core handles Layer 2/3 MAC scheduling, RLC, and HARQ control while the integrated SRIO provides high-bandwidth low-latency connectivity to companion DSPs for PHY. The 32-bit DDR2 ECC controller delivers sustained memory bandwidth needed for ciphering and packet queuing. Operating at 0-105C the device meets outdoor cabinet thermal envelopes without derating, and the 783-FCPBGA package supports the high pin density of multi-RF-chain designs.
推荐
Storage Area Network (SAN) Controller
The MPC8548PXATGD suits SPC iTarget SAN controllers where multiple PCI Express links and the hardware crypto engine accelerate iSCSI, FC, and SAS protocol processing. Its integrated 4-port GbE and PCIe controllers reduce external switch IC count; the e500 core at 1.2 GHz handles TCP/IP offload and RAID metadata operations. The DDR2 ECC controller with 32-bit interface delivers 4.8 GB/s peak bandwidth for read/write caching. The 0-105C junction rating supports standard rack-mount thermal envelopes, and the 783-FCPBGA package supports the high-pin-count I/O needed for multi-port back-end topologies.
推荐
Secure Communication Gateway
The MPC8548PXATGD suits secure communication gateways that require IPsec, SSL, and SRTPv4/VPN acceleration at line rate. The integrated crypto engine handles AES, 3DES, RSA, and SHA without an external accelerator, reducing BOM and PCIe slot utilization. Its 1.2 GHz e500 core runs the control plane, IKE negotiation, and policy enforcement while the hardware engine handles data-plane encryption. The 4 GbE MACs provide WAN/LAN/DMZ segmentation, and the DDR2 ECC controller protects key material. The 783-FCPBGA 29x29 mm footprint fits ATX-riser form factor enterprise gateway cards.
推荐
DSLAM / Carrier Ethernet Line Card
The MPC8548PXATGD fits DSLAM and Carrier Ethernet line cards where the e500 core at 1.2 GHz handles subscriber traffic shaping, QoS, and VLAN tagging across multiple GbE uplinks. Its integrated 4-port GbE and PCI/PCI-X controllers interface directly to PHY and DSL framer ICs without external bridges. The hardware crypto engine accelerates per-subscriber encryption, and the DDR2 ECC controller with 32-bit interface supports subscriber table lookups. Operating at 0-105C it meets typical outdoor cabinet thermal envelopes, and the 783-FCPBGA package integrates cleanly into high-density line-card layouts.
推荐
Industrial Control and Automation
The MPC8548PXATGD is suitable for industrial control applications requiring deterministic response time, multiple communication interfaces, and reliable operation in harsh environments. Its PCI/PCI-X/PCIe interfaces connect to motion controllers and I/O modules, while the 4 GbE MACs provide industrial Ethernet (PROFINET, EtherNet/IP, EtherCAT) gateway capability. The e500 core at 1.2 GHz runs real-time control loops and the DDR2 ECC memory against soft errors. The 0-105C operating range covers most factory-floor deployments, and the 783-FCPBGA package supports the high-pin-count multi-outlet common in industrial PC backplanes.
推荐
推荐产品汇总
工程参考数据： MPC8548PXATGD ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MPC8548PXAUVD | MPC8548PXAUPE | MPC8548PXATGB | MPC8548VTAQGD | MPC8545PXATGD |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 783-FCPBGA (29x29) | 783-FCPBGA (29x29) - same | 783-FCPBGA (29x29) - same | 783-FCPBGA (29x29) - same | 783-FCPBGA (29x29) - same | 783-FCPBGA (29x29) - same |
| Core | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC e500 | PowerPC e500 |
| Core Frequency | 1.2 GHz | 1.0 GHz (-17%) | 1.0 GHz (-17%) | 1.2 GHz | 1.2 GHz | 1.2 GHz |
| Operating Temperature | 0C to +105C | 0C to +105C | 0C to +105C | 0C to +105C | 0C to +105C | 0C to +105C |
| Integrated Security/Crypto Engine | Yes (hardware crypto accelerator) | Yes | Yes | Yes | Yes (with firewall/VIP classification) | Reduced |
| Serial RapidIO | Yes | Yes | Yes | Yes | Yes | No |
| Ethernet MACs | 4x Gigabit | 4x Gigabit | 4x Gigabit | 4x Gigabit | 4x Gigabit | 3x Gigabit |
关键差异点
- Highest speed bin at 1.2 GHz in the MPC85xx family （对比 MPC8548PXAUVD)
- Full MPCI e500 peripheral set including Serial RapidIO （对比 MPC8545PXATGD)
- Standard production revision TGD （对比 MPC8548PXAUPE)
设计说明
Estimated: the 783-FCPBGA 29x29 mm package with 1 mm ball pitch requires 6-layer PCB minimum. Use 0.5 oz copper outer layers with 1 oz inner planes; route signals on outer layers only with microvia-in-pad if breakout is tight. BGA escape routing should follow JEDEC MO-151 reference. Source: NXP AN3665 hardware layout guidance.
Estimated: at full 1.2 GHz utilization the MPC8548 dissipates approximately 7-9W. With the 783-FCPBGA die-down package, thermal performance depends on PCB copper area and airflow. Provide a 6x6 thermal via array (0.3 mm pitch, 0.2 mm drill) stitched to internal ground for adequate dissipation in 0-105C environments. Source: NXP MPC8548 hardware specifications thermal section.
The MPC8548PXATGD requires 1.0V core, 1.8V, 2.5V, and 3.3V rails with strict power sequencing: core voltage must reach 90% of nominal before segmentable rails per NXP hardware specifications. Use a multi-rail PMIC with programmable ramp rates; never use independent regulators without sequencing. Decoupling: 0.1uF X7R 0402 within 1 mm of each BGA power pin, plus 22uF polymer bulk caps per rail.
合规信息
RoHS and REACH compliant per NXP product page. Not AEC-Q100 qualified - this is a commercial/industrial networking MPU, not an automotive grade device.
