PCF8563BS/4,118 - 1mA I2C RTC | 400kHz | HVSON-10 | NXP
料号： PCF8563BS/4,118 ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $1.2 | $1.20 |
| 10 | $1.08 | $10.80 |
| 100 | $0.95 | $95.00 |
| 500 | $0.85 | $425.00 |
| 1,000 | $0.76 | $760.00 |
PCF8563BS/4,118 概述
What is an RTC? A Real-Time Clock is a dedicated integrated circuit that maintains accurate wall-clock time (date and time) independent of the main system processor, typically referenced to a 32.768 kHz quartz crystal. RTCs sit hierarchically as follows: RTC -> clock/calendar IC -> timing device -> mixed-signal IC -> semiconductor. Unlike software-based timekeeping derived from a microcontroller's oscillator, an RTC continues counting while the host MCU is in deep sleep or powered down, making it the standard solution for battery-backed time-of-day tracking.
Key features of the PCF8563BS/4,118 include a maximum clock supply current of 1 mA typical at 32 kHz, an integrated I2C slave interface running up to 400 kHz, a programmable square-wave clock output (32.768 kHz, 1024 Hz, 32 Hz, 1 Hz), an open-drain interrupt output, and an on-chip power-on reset plus voltage-low detector. These features let the host MCU wake only on calendar or alarm events, which minimizes total system energy use.
The device uses a low-power CMOS architecture with separate oscillator and timing registers, achieving the typical sub-1 microampere backup current needed for coin-cell battery operation. All 16 RTC registers and the 32.768 kHz trimming circuit are accessed over the standard I2C bus at slave address 0x51 (101 0001b), enabling easy drop-in replacement into designs that already use the PCF8563 footprint.
Typical applications include battery-backed wall-clock modules for metering and data loggers, timekeeping in IoT sensor nodes, alarm and timer functions in white goods, point-of-sale terminals, and any embedded system requiring calendar accuracy during MCU sleep or power loss. The wide 1.8 V to 5.5 V supply range also makes it suitable for 3.3 V and 5 V microcontroller rails.
When designing with the PCF8563, ensure the 32.768 kHz crystal load capacitance matches the oscillator's specified CL (typically 12.5 pF) and add a small decoupling capacitor on VCC. The exposed thermal pad of the HVSON-10 package should be soldered to the ground plane for mechanical stability and improved thermal dissipation.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a single source for sourcing, selecting, and implementing the PCF8563BS/4,118.
直接替换替代料： PCF8563BS/4,118 ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
快速对比工具——选择替代料号进行并排对比：
PCF8563BS/4
✅ 直接替换📋 参考替代料（不在目录中）
PCF8563BS/4,118
✅ 直接替换✓ 有现货
$0.76 / 个
查看数据手册 →PCF8563BS/4,118 规格参数
| 功能 | Real-Time Clock / Calendar |
| Bus Interface | I2C (2-wire serial), up to 400 kHz |
| I2C Slave Address | 0x51 (101 0001b) |
| Supply Voltage (VCC) | 1.8 V to 5.5 V |
| Backup Battery Voltage | 1.8 V to 5.5 V (separate supply domain) |
| Typical Clock Current (32 kHz) | 1 mA (maximum, per datasheet) |
| Time Format | HH:MM:SS and DD/MM/YYYY (BCD) |
| Calendar Functions | Year, month, day, weekday, hours, minutes, seconds |
| Programmable Clock Output | 32.768 kHz, 1024 Hz, 32 Hz, 1 Hz |
| Interrupt Output | Open-drain, programmable |
| Voltage-Low Detector | Integrated |
| Power-On Reset | Integrated (automatic) |
| External Crystal | 32.768 kHz quartz (customer supplied) |
| 封装 | HVSON-10 (3x3 mm, SOT650-1) with exposed pad |
| 安装类型 | Surface Mount |
| 工作温度 | -40 C to +85 C |
| MSL 等级 | 1 (per JEDEC J-STD-020) |
| RoHS 状态 | Compliant |
PCF8563BS/4,118 引脚配置
| 引脚 1 | OSCI — Oscillator input (32.768 kHz crystal) |
| 引脚 2 | OSCO — Oscillator output (32.768 kHz crystal) |
| 引脚 3 | INT — Interrupt output (open-drain) |
| 引脚 4 | VSS — Ground |
| 引脚 5 | SDA — I2C serial data |
| 引脚 6 | SCL — I2C serial clock |
| 引脚 7 | CLKOUT — Programmable clock output |
| 引脚 8 | VDD — Supply voltage |
| 引脚 9 | NC — Not connected |
| 引脚 10 | EP — Exposed thermal pad (tie to VSS) |
典型应用
PCF8563BS/4,118 适用于 6 应用s: Battery-Backed Wall-Clock Module, IoT Sensor Node Timekeeping, Data Logger Timestamp Source, White Goods and Appliance Timers, Point-of-Sale Terminal Time Reference, Embedded Metering (Electricity / Water / Gas).
Battery-Backed Wall-Clock Module
The PCF8563BS/4,118 provides continuous timekeeping for wall-clock modules that must keep accurate time across power cycles. The HVSON-10 package and 1.8 V to 5.5 V supply range allow a single CR2032 backup coin cell to maintain time for years while the main system is unpowered. Combined with the integrated voltage-low detector, the host MCU can read a low-battery flag and warn the user before the cell is fully depleted. The 1 mA maximum clock current is comfortably below the self-discharge rate of most lithium coin cells, ensuring multi-year calendar accuracy.
推荐
IoT Sensor Node Timekeeping
In IoT sensor nodes, the PCF8563BS/4,118 serves as the always-on time reference that timestamps measurements and wakes the host MCU only on scheduled events. Its sub-microampere backup current enables a coin cell to keep time while the wireless SoC is in deep sleep for months. The open-drain interrupt output can directly drive a wake-up GPIO on the MCU, eliminating the need for the host to poll the RTC over I2C. The wide 1.8 V to 5.5 V supply also simplifies direct connection to a single-cell Li-ion or 2xAA alkaline battery pack.
推荐
Data Logger Timestamp Source
Industrial and scientific data loggers rely on the PCF8563BS/4,118 to stamp every measurement sample with wall-clock time even when the main logger board is disconnected from line power. The HVSON-10 footprint saves PCB area versus SOIC-8 alternatives, allowing more channels or memory in the same enclosure. The I2C bus at 400 kHz lets the host read the full BCD register set in a single burst transaction, minimizing time spent in active mode. The integrated voltage-low detector flags when battery backup is failing so the user can service the unit before timestamps become invalid.
推荐
White Goods and Appliance Timers
Washing machines, ovens, and dishwashers use the PCF8563BS/4,118 to schedule delayed-start cycles and maintain accurate time across brief power interruptions. The -40 C to +85 C operating range is well suited to kitchen appliance environments, and the HVSON-10 package withstands standard reflow profiles. The programmable CLKOUT pin can drive a 1 Hz or 32 Hz square wave to a sub-controller without consuming the I2C bus. Its low cost and high reliability make it a popular choice in mid-volume consumer appliances.
推荐
Point-of-Sale Terminal Time Reference
POS terminals use the PCF8563BS/4,118 to time-stamp transactions for audit trails and end-of-day reporting, where regulatory compliance requires accurate time-of-day records. The 1 mA maximum clock supply current keeps power budgets low in battery-backed POS designs, and the integrated voltage-low detector can flag backup battery degradation to service technicians. The I2C address 0x51 is well documented in many existing POS firmware bases, allowing easy integration into legacy code.
推荐
Embedded Metering (Electricity / Water / Gas)
Smart meters for electricity, water, and gas use the PCF8563BS/4,118 to maintain accurate calendar time for time-of-use billing and event logging during multi-year deployment. The sub-microampere backup current is critical for sealed meters that cannot be opened to replace the battery during the design lifetime. The HVSON-10 footprint accommodates dense meter PCBs, and the integrated power-on reset ensures reliable startup after battery replacement in the field.
推荐
推荐产品汇总
工程参考数据： PCF8563BS/4,118 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PCF8563BS/4 | PCF8563BS/4,118 |
|---|---|---|---|
| Package | HVSON-10 (SOT650-1) 3x3 mm | HVSON-10 (SOT650-1) 3x3 mm - same | HVSON-10 (SOT650-1) 3x3 mm - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Function | RTC / Calendar | RTC / Calendar | RTC / Calendar |
| Supply Voltage | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| I2C Address | 0x51 | 0x51 | 0x51 |
| I2C Max Speed | 400 kHz | 400 kHz | 400 kHz |
| Max Clock Current | 1 mA | 1 mA | 1 mA |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
关键差异点
- Lowest-cost NXP RTC in HVSON-10 （对比 PCF85263AT/AX)
- Lower backup current than DS1307 （对比 DS1307)
- Faster I2C bus than DS1307 （对比 DS1307)
设计说明
Place the 32.768 kHz crystal as close as possible to the OSCI (pin 1) and OSCO (pin 2) traces, and keep the trace lengths under 5 mm to minimize parasitic capacitance. Route the SDA and SCL traces away from switching nodes and add 4.7 kohm pull-up resistors on both lines to VCC. The exposed pad (pin 10) must be soldered to the ground plane for mechanical stability and thermal dissipation.
Use a low-Iq LDO such as the MCP1700 for the main VDD rail, and connect the backup battery (CR2032) directly to the VDD pin through a Schottky diode OR-ing circuit so the RTC keeps time when main power is removed. Add a 100 nF decoupling capacitor close to VDD and a 10 microfarad bulk capacitor on the backup supply to handle the inrush during battery insertion.
Do not skip the external 32.768 kHz crystal - the PCF8563 has no internal oscillator. Use a crystal with 12.5 pF load capacitance and check the datasheet's oscillator startup time (typically 1 to 2 seconds). Avoid reading the time registers during a register rollover (typically around 1 second past each minute) without reading multiple times or using the chain-pointer technique to avoid invalid data.
合规信息
RoHS and REACH compliant per NXP product page. Not AEC-Q100 qualified - this part targets consumer/industrial segments, not automotive.
