PIC17LC44-08I/L - 8-Bit 8MHz OTP MCU 16KB | 44-PLCC | Microchip
料号： PIC17LC44-08I/L ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $7.95 | $7.95 |
| 10 | $7.15 | $71.50 |
| 100 | $6.3 | $630.00 |
| 500 | $5.55 | $2,775.00 |
| 1,000 | $4.95 | $4,950.00 |
PIC17LC44-08I/L 概述
What is a PIC17C-series microcontroller? The PIC17C is Microchip's first 16-bit-instruction-word, 8-bit-data architecture, sitting above the PIC16 family in the 8-bit hierarchy and below the PIC18 family. It executes every instruction (except program branches and table reads/writes) in a single 121 ns cycle at 8 MHz, supports 58 single-word instructions, and integrates an 8-level hardware stack plus a multiply instruction - features that historically made it Microchip's highest-performance 8-bit core before the PIC18 was introduced. PIC17C microcontrollers remain in active service today for long-life industrial and aerospace equipment.
Key features of the PIC17LC44-08I/L include an 8 MHz internal oscillator input, brown-out reset, watchdog timer, two 8-bit timers and one 16-bit timer/counter, a hardware USART, and an 11-channel 10-bit analog-to-digital converter. The OTP program memory supports in-circuit programming via the standard Microchip ICSP interface, simplifying prototype-to-production transitions. The 44-PLCC package uses a J-lead style footprint suitable for socketed production programming.
In terms of architecture, the PIC17C44 uses a 16-bit-wide instruction path with an 8-bit data path, a multi-source interrupt controller with prioritized vectors, and on-chip RC oscillator or external crystal support. The 454-byte general-purpose RAM is shared with the stack, and the 16 KB program space is addressed by a 16-bit program counter that allows linear code beyond the 14-bit PIC16 limit.
Typical applications include industrial motor control, HVAC controllers, legacy instrumentation front-ends, embedded control panels, and retrofits of older 8051-class designs where a higher-performance 8-bit core with more RAM and code space is required. Design considerations when migrating to or from this part include verifying ICSP programming voltage compatibility, mapping legacy 40-pin DIP footprints to the 44-PLCC carrier, and ensuring brown-out reset thresholds are tuned to the 2.5 V minimum supply. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.
直接替换替代料： PIC17LC44-08I/L ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： PIC17LC44-08I/L （相同外形与封装尺寸） ——差异在于 Package, Data Bus Width, Program Memory Size, Mounting Type, Maximum Clock Frequency.
快速对比工具——选择替代料号进行并排对比：
PIC17LC43-08I/L
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$18.24 / 个
查看数据手册 →PIC17LC44-08I/PQ
✅ 直接替换📋 参考替代料（不在目录中）
PIC17LC44-08/PT
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$4.1 / 个
查看数据手册 →PIC17LC44-08/P
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$6.95 / 个
查看数据手册 →PIC17LC44-08I/L 最大额定值与电气特性
| Core Architecture | PIC17C 8-bit RISC |
| Program Memory Type | OTP (One-Time Programmable) |
| Program Memory Size | 16 KB (8K x 16) |
| RAM Size | 454 bytes |
| EEPROM Size | 0 bytes (none) |
| CPU Clock Speed | 8 MHz |
| Instruction Cycle Time | 121 ns (single-cycle, non-branch) |
| Instruction Set Size | 58 single-word instructions |
| Supply Voltage Range | 2.5 V to 5.5 V |
| I/O Pins | 33 |
| Timers | 2 x 8-bit + 1 x 16-bit |
| ADC | 11-channel, 10-bit |
| Communication | 1 x USART (SCI) |
| Watchdog Timer | Yes (hardware WDT) |
| Brown-out Reset | Yes |
| In-Circuit Programming | ICSP supported |
| 封装 | 44-pin PLCC (16.59 x 16.59 mm) |
| 安装类型 | Surface Mount (PLCC socket compatible) |
| 工作温度范围 | -40 C to +85 C (Industrial, /L = PLCC suffix) |
| RoHS 状态 | Compliant (per Microchip product page) |
PIC17LC44-08I/L 引脚配置
| 引脚 1 | RA0/AN0 — Port A bit 0 / ADC input 0 |
| 引脚 2 | RA1/AN1 — Port A bit 1 / ADC input 1 |
| 引脚 3 | RA2/AN2 — Port A bit 2 / ADC input 2 |
| 引脚 4 | RA3/AN3 — Port A bit 3 / ADC input 3 |
| 引脚 5 | RA4/AN4 — Port A bit 4 / ADC input 4 |
| 引脚 6 | RA5/AN5 — Port A bit 5 / ADC input 5 |
| 引脚 7 | RA6/AN6 — Port A bit 6 / ADC input 6 |
| 引脚 8 | RA7/AN7 — Port A bit 7 / ADC input 7 |
| 引脚 9 | RB0/INT — Port B bit 0 / External interrupt |
| 引脚 10 | RB1 — Port B bit 1 |
| 引脚 11 | RB2 — Port B bit 2 |
| 引脚 12 | RB3 — Port B bit 3 |
| 引脚 13 | RB4 — Port B bit 4 |
| 引脚 14 | RB5 — Port B bit 5 |
| 引脚 15 | RB6 — Port B bit 6 |
| 引脚 16 | RB7 — Port B bit 7 |
| 引脚 17 | VSS — Ground reference |
| 引脚 18 | VDD — Positive supply (2.5 V - 5.5 V) |
| 引脚 19 | OSC1/CLKIN — Crystal oscillator input / external clock |
| 引脚 20 | OSC2/CLKOUT — Crystal oscillator output / clock out |
| 引脚 21 | RC0 — Port C bit 0 |
| 引脚 22 | RC1 — Port C bit 1 |
| 引脚 23 | RC2 — Port C bit 2 |
| 引脚 24 | RC3 — Port C bit 3 |
| 引脚 25 | RC4 — Port C bit 4 |
| 引脚 26 | RC5 — Port C bit 5 |
| 引脚 27 | RC6 — Port C bit 6 |
| 引脚 28 | RC7 — Port C bit 7 |
| 引脚 29 | RD0 — Port D bit 0 |
| 引脚 30 | RD1 — Port D bit 1 |
| 引脚 31 | RD2 — Port D bit 2 |
| 引脚 32 | RD3 — Port D bit 3 |
| 引脚 33 | RD4 — Port D bit 4 |
| 引脚 34 | RD5 — Port D bit 5 |
| 引脚 35 | RD6 — Port D bit 6 |
| 引脚 36 | RD7 — Port D bit 7 |
| 引脚 37 | MCLR/VPP — Master clear reset / programming voltage |
| 引脚 38 | TX/CK — USART transmit / clock line |
| 引脚 39 | RX/DT — USART receive / data line |
| 引脚 40 | RE0/AN8 — Port E bit 0 / ADC input 8 |
| 引脚 41 | RE1/AN9 — Port E bit 1 / ADC input 9 |
| 引脚 42 | RE2/AN10 — Port E bit 2 / ADC input 10 |
| 引脚 43 | VSS — Ground reference (digital) |
| 引脚 44 | VDD — Positive supply (digital core) |
典型应用
PIC17LC44-08I/L 适用于 6 应用s: Industrial Motor Control, HVAC Controller Boards, Legacy Instrumentation Front-End, Embedded Control Panels, 8051/PIC16 Retrofit Designs, Aerospace Avionics Subsystems.
Industrial Motor Control
The PIC17LC44-08I/L is well suited to legacy industrial motor control boards that already use a PIC17C44 socket. Its 11-channel 10-bit ADC reads current shunts and tachometer feedback with adequate resolution for closed-loop speed control, while the 16-bit timer/counter handles PWM generation and quadrature decoding. The 33 I/O pins support direction relays, opto-isolated enable lines, and fault-interrupt inputs. Operating from 2.5 V to 5.5 V simplifies 24 V->5 V system rails. For new designs prefer dsPIC33EP64MC, but for retrofitting existing PIC17C-based motor controllers the PIC17LC44-08I/L is a drop-in.
推荐
HVAC Controller Boards
HVAC control units that already run PIC17C44 firmware can extend service life using the PIC17LC44-08I/L as an exact replacement. The 8 MHz instruction cycle (121 ns) handles temperature-setpoint scheduling, damper actuator PWM, and multi-zone thermostat loops. The 16 KB OTP program memory stores lookup tables for defrost cycles and compressor staging, while 454 bytes of RAM is sufficient for short trend buffers. Brown-out reset protects against brown-outs during compressor inrush. Recommended migration for new HVAC designs: PIC18F46K22 with more RAM and lower sleep current.
推荐
Legacy Instrumentation Front-End
Bench instruments and panel meters built around the PIC17C44 retain a 44-PLCC socket on the PCB; the PIC17LC44-08I/L fits directly without rework. Its 10-bit ADC digitizes thermocouple, RTD and 4-20 mA sensor inputs through external signal conditioning. The hardware USART outputs serial data to legacy SCADA or RS-232 terminals. The 8 MHz clock delivers deterministic cycle times for FIR-filter-style smoothing in firmware. Industrial temperature grade (-40 C to +85 C) ensures operation in unheated enclosures. Designers upgrading to modern silicon should evaluate the dsPIC33EV family.
推荐
Embedded Control Panels
Operator control panels with 7-segment or character-LCD displays can use the PIC17LC44-08I/L to drive multiplexed LED digits and scan keypads via its 33 I/O pins. The 16 KB OTP stores menu state machines, debounce tables and fault log structures. The hardware USART connects to a host PLC or remote I/O link. Operating from 2.5 V to 5.5 V supports battery-backed control panels. Use the watchdog timer to recover from firmware hangs in unattended installations. The PIC17LC44-08I/L is specifically chosen when preserving the 44-PLCC socket footprint avoids PCB rework.
推荐
8051/PIC16 Retrofit Designs
Designers porting firmware from 8051 or PIC16F platforms benefit from the PIC17LC44-08I/L's 16-bit instruction word and 8-level hardware stack, which raise code density and execution speed. Its 58 single-word instructions map cleanly to legacy 8051 C code. The 16 KB OTP holds more application logic than a typical PIC16F877 with 14 KB flash, while the 454-byte RAM exceeds the 368 bytes of a PIC16F877. Industrial temperature grade and 2.5 V-5.5 V operation simplify migration into existing 5 V analog rails. For new 5 V designs today, Microchip recommends PIC18F46K22 with more peripherals.
推荐
Aerospace Avionics Subsystems
Long-life aerospace subsystems continue to use the PIC17LC44-08I/L because of its mature silicon, qualified at industrial temperature grade and known reliability record. Its 8 MHz execution provides deterministic timing for sensor fusion in attitude-indicator and fuel-metering units. The 33 I/O pins drive MIL-STD-1553 transceivers via external logic, while the 10-bit ADC reads synchro/resolver feedback through external conversion. Many aerospace platforms have approved the PIC17LC44-08I/L in their BOM, so field replacements are simply socket swaps with the same part number. For new aerospace designs consult Microchip's aerospace-grade PIC16/18 variants.
推荐
推荐产品汇总
工程参考数据： PIC17LC44-08I/L ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PIC17LC43-08I/L | PIC17LC44-08I/PQ | PIC17LC44-08/PT | PIC17LC44-08/P |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-pin PLCC | 44-pin PLCC | 44-pin PDIP (PQ) | 44-pin TQFP (PT) | 40-pin PDIP (P) |
| Program Memory | 16 KB OTP | 8 KB OTP | 16 KB OTP | 16 KB OTP | 16 KB OTP |
| RAM Size | 454 bytes | 454 bytes | 454 bytes | 454 bytes | 454 bytes |
| CPU Clock | 8 MHz | 8 MHz | 8 MHz | 8 MHz | 8 MHz |
| Operating Voltage | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V |
| I/O Pins | 33 | 33 | 33 | 33 | 33 |
| ADC | 11-ch, 10-bit | 11-ch, 10-bit | 11-ch, 10-bit | 11-ch, 10-bit | 11-ch, 10-bit |
| Temperature Grade | Industrial (-40 C to +85 C) | Industrial (-40 C to +85 C) | Industrial (-40 C to +85 C) | Commercial (0 C to +70 C) | Commercial (0 C to +70 C) |
关键差异点
- Larger 16 KB OTP program memory （对比 PIC17LC43-08I/L)
- Industrial temperature grade (-40 C to +85 C) （对比 PIC17LC44-08/PT)
- Low-voltage operation to 2.5 V （对比 PIC17C44-16I/L)
设计说明
The PIC17LC44-08I/L operates from 2.5 V to 5.5 V on VDD. Estimated: a 5 V system drawing 25 mA active plus 5 mA ADC reference burns approximately 150 mW. Place a 100 nF ceramic decoupling capacitor as close as possible to each VDD pin (pins 18 and 44), plus a bulk 10 uF tantalum on the main supply rail. Always enable brown-out reset (BOR) in the configuration word when operating below 5 V to prevent code execution during supply droops below 2.0 V.
The 44-pin PLCC socket accepts through-hole mounting but the part itself is rated for surface-mount assembly via the J-leads. When designing a new board around the PIC17LC44-08I/L, route OSC1/OSC2 traces symmetrically and keep them shorter than 20 mm to avoid EMI pickup. The ICSP pins (MCLR/VPP, RB6, RB7) must be brought out to a 6-pin header for in-circuit programming. Place the crystal or resonator within 10 mm of OSC1/OSC2, with a guard ring tied to ground.
Estimated: programming the PIC17LC44-08I/L requires Microchip ICSP at 12.5 V on MCLR/VPP; attempting low-voltage programming will not erase the OTP and may lock the device. Always apply MCLR rise after VDD is stable. When porting code from PIC16F to PIC17C44, note that the 16-bit instruction word changes the program counter model - PC bits are not aliased to PCLATH. Also, the PIC17C has no hardware multiplier interrupts beyond the standard PIR registers, so design interrupt latency accordingly.
合规信息
RoHS compliance per Microchip product page; this is an industrial-grade 8-bit MCU and is not AEC-Q100 qualified. Reach and conflict-minerals declarations per Microchip supplier compliance portal.
