PIC18F1330T-I/SO - 8KB Flash 40MHz 8-bit MCU | Microchip | 18-SOIC
料号： PIC18F1330T-I/SO ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $3.45 | $3.45 |
| 10 | $3.1 | $31.00 |
| 100 | $2.78 | $278.00 |
| 500 | $2.45 | $1,225.00 |
| 1,000 | $2.15 | $2,150.00 |
PIC18F1330T-I/SO 概述
An 8-bit microcontroller (MCU) is a small, self-contained computer-on-a-chip that combines a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and a set of mixed-signal peripherals (ADC, PWM, timers, communication ports) onto a single die. Within the broader taxonomy, PIC18 belongs to Microchip's enhanced mid-range 8-bit family, which sits below the 16-bit dsPIC/PIC24 and 32-bit PIC32 families, and is widely deployed in cost- and power-sensitive embedded designs where deterministic interrupt response and simple programming models outweigh raw computational throughput.
Key specifications of the PIC18F1330T-I/SO include 8 KB Flash, 256 bytes RAM, 16 general-purpose I/O pins, an integrated 10-bit ADC, a Power Control PWM module with up to 6 PWM channels, and operating voltage of 2.0 V to 5.5 V. The 40 MHz internal oscillator and 200 ns instruction execution allow deterministic loop control, while the SOIC-18 industrial-temperature (-40C to +85C) package supports surface-mount assembly for production volumes.
Architecturally, the PIC18F1330T-I/SO implements Microchip's enhanced Harvard RISC core with a 16-bit instruction word and 8-bit data path, providing high code density in C and assembly. The on-chip Power Control PWM (PCPWM), 10-bit ADC, and configurable peripherals enable fully digital closed-loop control of brushed DC, brushless DC, and switched-reluctance motors without external driver ICs, which simplifies BOM and reduces board area.
Typical applications include motor control (BLDC, PMSM, brushed DC), sensorless fan control, switched-mode power supply (SMPS) digital control loops, LED lighting drivers with dimming, and small appliance control boards. The integrated high-resolution PWM and ADC pairs make this MCU especially well-suited to closed-loop current/voltage regulation.
A critical design consideration is choosing between internal and external oscillator modes for noise-sensitive analog measurements; for motor-control designs the 40 MHz Fosc with PLL can introduce switching noise on ADC channels and may require careful grounding and filter selection. The 18-pin SOIC package leaves only 16 GPIO pins, so design reuse from larger PIC18F variants requires careful peripheral remapping.
This page synthesizes distributor pricing, parametric proximity scores for drop-in alternatives, and PCB-layout guidance specific to the PIC18F1330T-I/SO - engineering context not consolidated in the manufacturer datasheet alone.
直接替换替代料： PIC18F1330T-I/SO ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： PIC18F1330T-I/SO （相同外形与封装尺寸） ——差异在于 Package, ADC, Operating Temperature, Core, MSL Level.
快速对比工具——选择替代料号进行并排对比：
PIC18F1330-I/SO
✅ 直接替换✓ 有现货
$1.95 / 个
查看数据手册 →PIC18F1320T-I/SO
✅ 直接替换✓ 有现货
$4.21 / 个
查看数据手册 →PIC18F1220-I/SO
✅ 直接替换📋 参考替代料（不在目录中）
PIC18F1330T-I/SO 最大额定值与电气特性
| Core | PIC 8-bit enhanced Harvard RISC |
| Program Memory | 8 KB Flash (4K x 16) |
| Data Memory (RAM) | 256 bytes |
| Maximum CPU Frequency | 40 MHz |
| Instruction Execution | 200 ns at 40 MHz |
| Operating Voltage | 2.0 V to 5.5 V |
| I/O Pins | 16 |
| ADC | 10-bit, 5 channels |
| PWM Channels | Up to 6 (Power Control PWM) |
| Timers | Timer0/1/2/3 |
| 封装 | 18-SOIC (7.50 mm body width, 0.295 inch) |
| 工作温度 | -40C to +85C (Industrial) |
| 安装类型 | Surface Mount |
| MSL 等级 | 1 |
| RoHS 状态 | Compliant |
PIC18F1330T-I/SO 引脚配置
| 引脚 1 | MCLR/RA3 — Master Clear (reset) input or GPIO RA3 |
| 引脚 2 | OSC1/RA0 — Crystal oscillator input or GPIO RA0 |
| 引脚 3 | OSC2/RA1 — Crystal oscillator output or GPIO RA1 |
| 引脚 4 | RA2 — GPIO RA2 |
| 引脚 5 | RA5 — GPIO RA5 / analog input |
| 引脚 6 | VSS — Ground reference |
| 引脚 7 | VDD — Positive supply voltage (2.0-5.5 V) |
| 引脚 8 | RB0 — GPIO RB0 / INT0 external interrupt |
| 引脚 9 | RB1 — GPIO RB1 |
| 引脚 10 | RB2 — GPIO RB2 |
| 引脚 11 | RB3 — GPIO RB3 |
| 引脚 12 | RB4 — GPIO RB4 |
| 引脚 13 | RB5 — GPIO RB5 / PWM output |
| 引脚 14 | RB6 — GPIO RB6 / PWM output / ICSP clock |
| 引脚 15 | RB7 — GPIO RB7 / PWM output / ICSP data |
| 引脚 16 | RA6 — GPIO RA6 / analog input |
| 引脚 17 | RA7 — GPIO RA7 / analog input |
| 引脚 18 | VSS — Ground reference (secondary) |
典型应用
PIC18F1330T-I/SO 适用于 6 应用s: BLDC and PMSM Motor Control, Sensorless Fan and Pump Speed Control, Switched-Mode Power Supply (SMPS) Digital Control, LED Lighting Drivers with Dimming, Small Appliance Control Boards, Industrial Sensor Signal Conditioning.
BLDC and PMSM Motor Control
The PIC18F1330T-I/SO suits small BLDC and PMSM motor drives where the integrated Power Control PWM module eliminates external gate-driver ICs. Its 6 PWM channels support complementary drive with programmable dead-band, while the 10-bit ADC samples phase currents for sensorless back-EMF control loops. Compared with discrete analog motor-control solutions, this MCU reduces BOM count by 5-8 components and provides firmware-driven commutation tuning over the full operating envelope from 2-5.5 V supply.
推荐
Sensorless Fan and Pump Speed Control
For sensorless cooling fans and small liquid pumps, the PIC18F1330T-I/SO provides back-EMF zero-crossing detection and closed-loop RPM control without an external Hall sensor. The 40 MHz CPU executes the commutation algorithm and PID loop within microseconds, while the 256-byte RAM holds state variables and the 8 KB Flash stores the full sensorless algorithm. Operating from 3.3 V or 5 V fan rails, this MCU replaces legacy analog fan-control ICs with digital accuracy and quieter acoustics.
推荐
Switched-Mode Power Supply (SMPS) Digital Control
The PIC18F1330T-I/SO can implement digital control loops for small isolated and non-isolated SMPS topologies up to roughly 100 W output. Its 40 MHz Fosc and 10-bit ADC with fast conversion enable voltage-mode and peak-current-mode control at 100-500 kHz switching frequencies. Compared with analog UC3842-style controllers, the MCU-based approach adds adaptive over-current protection, soft-start sequencing, and digital telemetry via UART or I2C. Use the high-resolution Power Control PWM to drive a digital optocoupler or gate-driver transformer.
推荐
LED Lighting Drivers with Dimming
Architectural and industrial LED drivers benefit from the PIC18F1330T-I/SO's 6 PWM channels for multi-channel RGBW or tunable-white dimming. The MCU provides logarithmic dimming curves, color-temperature compensation, and DALI or 0-10 V dimming protocol decoding without external DSP. With 8 KB Flash, designers can store multiple lighting scenes and smooth-fade algorithms. The integrated ADC monitors LED current for thermal foldback, extending luminaire lifetime in enclosed fixtures.
推荐
Small Appliance Control Boards
Coffee machines, blenders, air purifiers, and other small appliances use the PIC18F1330T-I/SO as the main control MCU for motor drive, user-interface button scanning, and LCD or LED status display. Its 18-SOIC package fits in tight enclosures, and 2.0-5.5 V operation accepts battery or rectified-mains-derived rails directly. The 256-byte RAM is sufficient for state-machine-based appliance logic, and 8 KB Flash holds the full user-interface firmware plus factory calibration constants.
推荐
Industrial Sensor Signal Conditioning
Process-control sensor transmitters and 4-20 mA current-loop nodes use the PIC18F1330T-I/SO to digitize analog sensor inputs, apply linearization curves, and drive the loop-current PWM with calibrated accuracy. The 10-bit ADC provides sufficient resolution for temperature, pressure, and flow sensors in non-precision applications, while the 6 PWM channels can drive H-bridge excitation for bridge-type sensors. Compared with pure analog signal chains, the MCU adds digital calibration storage in Flash and self-test routines.
推荐
推荐产品汇总
工程参考数据： PIC18F1330T-I/SO ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PIC18F1330-I/SO | PIC18F1330-I/SS | PIC18F1320T-I/SO | PIC18F1230-I/P | PIC18F1220-I/SO |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | SOIC-18 | SOIC-18 (same) | SSOP-20 (different) | SOIC-18 (same) | PDIP-18 (different) | SOIC-18 (same) |
| Flash Memory | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 2 KB |
| RAM | 256 bytes | 256 bytes | 256 bytes | 256 bytes | 256 bytes | 256 bytes |
| Maximum Frequency | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz |
| Power Control PWM | Yes (10-bit, 6 channels) | Yes (10-bit, 6 channels) | Yes (10-bit, 6 channels) | No | Yes | No |
| Operating Voltage | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V |
| ADC | 10-bit, 5 channels | 10-bit, 5 channels | 10-bit, 5 channels | 10-bit, 5 channels | 10-bit, 4 channels | 10-bit, 4 channels |
关键差异点
- Integrated Power Control PWM peripheral for motor control （对比 PIC18F1320T-I/SO)
- Higher Flash density than entry-level PIC18F1220 （对比 PIC18F1220-I/SO)
- Industrial temperature range on SOIC package （对比 PIC18F1330-I/SS (SSOP variant))
设计说明
The PIC18F1330T-I/SO requires a bulk decoupling capacitor of at least 100 nF within 5 mm of the VDD pin, plus a 10 uF bulk capacitor on the main supply rail. The internal voltage regulator is sensitive to supply ripple; place the decoupling capacitor directly between VDD (pin 7) and VSS (pin 6) using short, wide PCB traces. For motor-control designs where VDD is derived from a switching regulator, add a ferrite bead or LC filter between the switching rail and the MCU VDD to prevent switching noise from coupling into the ADC reference.
The PIC18F1330T-I/SO MCLR pin (pin 1) is internally weakly pulled-up in some configurations but should always have an external pull-up of 10 kohm to VDD for reliable reset behavior. The ICSP programming pins (RB6/RB7) must not be permanently pulled low during normal operation or programming will fail. Brown-out detection must be enabled in CONFIG registers for any application where supply voltage could dip below 2.0 V momentarily.
Separate analog and digital ground planes where the PCB stack-up allows, joining them only at a single point near the MCU VSS pin (pin 6). Keep the analog reference voltage traces (AVDD/AVSS if used) routed away from PWM switching traces to minimize ADC noise pickup. The crystal or resonator on OSC1/OSC2 (pins 2/3) should be placed within 5 mm of the MCU with a ground guard ring on the PCB.
合规信息
RoHS and REACH compliant per Microchip product declaration. Industrial temperature grade -40C to +85C (not AEC-Q100 automotive qualified - choose AEC-Q100 qualified PIC18 variants for automotive). Lead-free and conflict-minerals compliant per Microchip supplier policy.
