PIC32MX230F064DT-V/PT - 40MHz 32-bit MCU, 64KB Flash, 44-TQFP | Microchip
料号： PIC32MX230F064DT-V/PT ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $4.85 | $4.85 |
| 10 | $4.36 | $43.60 |
| 100 | $3.88 | $388.00 |
| 500 | $3.49 | $1,745.00 |
| 1,000 | $3.1 | $3,100.00 |
PIC32MX230F064DT-V/PT 概述
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and peripheral interfaces such as timers, ADC, and communication buses. The PIC32MX230 sits within the broader taxonomy of embedded controllers (32-bit MCU -> MIPS-based MCU -> PIC32 family -> Microchip 8/16/32-bit portfolio), serving as a bridge between 8-bit PIC16/PIC18 designs and higher-performance Cortex-M parts. The MIPS32 M4K core delivers 1.5 DMIPS/MHz, supporting deterministic real-time control alongside rich connectivity for HMI and audio applications.
Key features include 0.5 mA/MHz active current for low-power designs, 1 ns high-resolution timer capture for precise measurements, on-chip temperature sensor, 34 general-purpose I/O pins with PPS remapping, and an automotive-grade -V temperature rating of -40 C to +105 C. The device supports both industrial (AEC-Q100 not mandatory) and automotive-grade deployments where extended thermal range and ruggedness are required, making it suitable for under-hood and harsh-environment nodes.
The architecture combines a 5-stage MIPS pipeline with single-cycle multiply and hardware divide, enabling deterministic interrupt latency for motor-control and audio codec loops. Internal oscillator options and flexible clock switching reduce external component count, while the PMP module directly drives TFT LCDs without an external gate-driver ASIC. USB 2.0 full-speed with on-chip transceiver and dedicated DMA channels simplifies tethered peripherals such as HID, CDC, and audio class devices.
Typical applications include automotive body electronics, consumer audio interfaces with I2S codecs, low-cost TFT HMI panels, capacitive-touch user interfaces, USB HID peripherals, and industrial sensor hubs. The combination of USB, audio interfaces, and graphics PMP within a compact 44-TQFP footprint makes the PIC32MX230 particularly attractive for cost-sensitive multimedia nodes.
When designing with this MCU, allocate adequate decoupling (100 nF per VDD/VSS pair plus a 4.7 uF bulk), keep the 40 MHz trace lengths short, and use the PPS feature to remap peripherals to convenient pins rather than re-routing the PCB. For USB designs, the 90 ohm differential pair must be routed with controlled impedance.
This page consolidates distributor pricing as of 2026-10-02, drop-in same-package alternatives, and practical design notes beyond what the Microchip datasheet alone provides.
直接替换替代料： PIC32MX230F064DT-V/PT ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： PIC32MX230F064DT-V/PT （相同外形与封装尺寸） ——差异在于 Package, ADC, Timers, Operating Temperature, Core Architecture.
快速对比工具——选择替代料号进行并排对比：
PIC32MX230F064DT-I/PT
✅ 直接替换📋 参考替代料（不在目录中）
PIC32MX230F064DT-V/ML
✅ 直接替换✓ 有现货
$3.95 / 个
查看数据手册 →PIC32MX130F064DT-V/PT
✅ 直接替换✓ 有现货
$2.94 / 个
查看数据手册 →PIC32MX230F064BT-V/ML
✅ 直接替换✓ 有现货
$2.13 / 个
查看数据手册 →PIC32MX220F032DT-V/PT
✅ 直接替换✓ 有现货
$2.55 / 个
查看数据手册 →PIC32MX250F128DT-V/PT
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
PIC32MX230F064DT-V/PT 最大额定值与电气特性
| Core Architecture | MIPS32 M4K, 32-bit RISC |
| Maximum Clock Speed | 40 MHz (66 DMIPS) |
| Program Memory (Flash) | 64 KB (64K x 8) |
| SRAM | 16 KB |
| Operating Voltage Range | 2.3 V to 3.6 V |
| 工作温度范围 | -40 C to +105 C (Automotive -V grade) |
| I/O Pins | 34 general-purpose |
| 封装 | 44-pin TQFP (10x10 mm), 0.80 mm pitch |
| ADC | 10-bit, up to 1 Msps, 13 channels |
| USB | USB 2.0 Full-Speed Device/Host/OTG with on-chip transceiver |
| Communication Interfaces | 2x I2C, 2x SPI, 2x I2S, 2x UART, PMP |
| Timers | Five 16-bit timers/counters with Input Capture and Output Compare |
| Active Current Consumption | 0.5 mA/MHz typical |
| Peripheral Pin Select (PPS) | Yes - remappable peripherals |
| Parallel Master Port (PMP) | Yes - 8/16-bit data, up to 16 address lines |
| On-chip Temperature Sensor | Yes |
| Capacitive Touch Support | mTouch (via ADC/CTMU) |
| AEC-Q100 Qualification | Automotive grade -V suffix |
| RoHS 状态 | Compliant |
| 安装类型 | Surface Mount |
PIC32MX230F064DT-V/PT 引脚配置
| 引脚 1 | RPB0/AN0 — Remappable I/O, analog input 0 |
| 引脚 2 | RPB1/AN1 — Remappable I/O, analog input 1 |
| 引脚 3 | RPB2/AN2 — Remappable I/O, analog input 2 |
| 引脚 4 | RPB3/AN3 — Remappable I/O, analog input 3 |
| 引脚 5 | VDD — Positive supply voltage (2.3-3.6 V) |
| 引脚 6 | VSS — Ground reference |
| 引脚 7 | RPB4/AN4 — Remappable I/O, analog input 4 |
| 引脚 8 | RPB5/AN5 — Remappable I/O, analog input 5 |
| 引脚 9 | RPB6/PGEC1 — Remappable I/O / ICSP clock 1 |
| 引脚 10 | RPB7/PGED1 — Remappable I/O / ICSP data 1 |
| 引脚 11 | VSS — Ground reference |
| 引脚 12 | VDD — Positive supply voltage (2.3-3.6 V) |
| 引脚 13 | RPB8/AN8 — Remappable I/O, analog input 8 |
| 引脚 14 | RPB9/AN9 — Remappable I/O, analog input 9 |
| 引脚 15 | RPB10/AN10 — Remappable I/O, analog input 10 |
| 引脚 16 | RPB11/AN11 — Remappable I/O, analog input 11 |
| 引脚 17 | VSS — Ground reference |
| 引脚 18 | VDD — Positive supply voltage (2.3-3.6 V) |
| 引脚 19 | PGEC2/RPB12 — ICSP clock 2 / remappable I/O |
| 引脚 20 | PGED2/RPB13 — ICSP data 2 / remappable I/O |
| 引脚 21 | RPB14 — Remappable I/O |
| 引脚 22 | RPB15/AN15 — Remappable I/O, analog input 15 |
| 引脚 23 | AN16/RPC0 — Analog input 16 / remappable I/O |
| 引脚 24 | AN17/RPC1 — Analog input 17 / remappable I/O |
| 引脚 25 | AN18/RPC2 — Analog input 18 / remappable I/O |
| 引脚 26 | RPC3 — Remappable I/O |
| 引脚 27 | VDD — Positive supply voltage (2.3-3.6 V) |
| 引脚 28 | VSS — Ground reference |
| 引脚 29 | RPC4 — Remappable I/O |
| 引脚 30 | RPC5 — Remappable I/O |
| 引脚 31 | RPC6 — Remappable I/O |
| 引脚 32 | RPC7 — Remappable I/O |
| 引脚 33 | RPC8 — Remappable I/O |
| 引脚 34 | RPC9 — Remappable I/O |
| 引脚 35 | VSS — Ground reference |
| 引脚 36 | OSC1/CLKI/RC12 — Crystal oscillator input / external clock |
| 引脚 37 | OSC2/CLKO/RC15 — Crystal oscillator output / clock out |
| 引脚 38 | VUSB — USB transceiver supply (3.3 V) |
| 引脚 39 | D+/RPC10 — USB D+ line / remappable I/O |
| 引脚 40 | D-/RPC11 — USB D- line / remappable I/O |
| 引脚 41 | VDD — Positive supply voltage (2.3-3.6 V) |
| 引脚 42 | MCLR — Master clear (reset), active low |
| 引脚 43 | RPA0 — Remappable I/O |
| 引脚 44 | RPA1 — Remappable I/O |
典型应用
PIC32MX230F064DT-V/PT 适用于 6 应用s: Automotive Body Electronics Modules, USB Audio / I2S Codec Interfaces, Low-Cost TFT HMI Panels, Capacitive Touch User Interfaces, USB HID Peripheral Devices, Industrial Sensor Hubs.
Automotive Body Electronics Modules
The PIC32MX230F064DT-V/PT fits automotive body modules thanks to its AEC-Q100 qualification, -40 C to +105 C automotive-V temperature range, and 34 GPIO with Peripheral Pin Select. At 40 MHz it drives CAN-capable companion transceivers, body control logic, and LIN master tasks via UART. The 0.5 mA/MHz active current keeps sleep-mode quiescent drain low for always-on body nodes, while PPS allows pin reassignment without PCB rework when the BOM changes.
推荐
USB Audio / I2S Codec Interfaces
The PIC32MX230F064DT-V/PT serves USB audio class (UAC1) devices by combining USB 2.0 full-speed OTG with two I2S/SPIs. At 40 MHz it streams 16-bit/48 kHz stereo audio from a host to a delta-sigma DAC without DMA overruns. The integrated USB transceiver eliminates external PHY cost, while 16 KB SRAM buffers two stereo frames at 48 kHz. AEC-Q100 qualification makes it attractive for automotive infotainment auxiliary audio inputs.
推荐
Low-Cost TFT HMI Panels
The PIC32MX230F064DT-V/PT drives small TFT LCDs via the Parallel Master Port (PMP) without an external gate-driver ASIC. Up to 16 address lines and 8/16-bit data width let the PMP interface directly with ST7789V and ILI9341 controllers in 8-bit 8080 mode. PPS remaps PMP to convenient pins, while 64 KB Flash holds a full-color GUI framework plus custom fonts. The 44-TQFP provides enough I/O for both display and capacitive-touch buttons via mTouch.
推荐
Capacitive Touch User Interfaces
The PIC32MX230F064DT-V/PT supports mTouch capacitive-touch buttons and sliders via the on-chip CTMU and ADC, eliminating external touch ICs. Up to 13 ADC channels drive a 4x4 button matrix plus a 100 mm slider, all scanned within 4 ms at 40 MHz. The automotive -V temperature grade suits industrial control panels, while PPS frees up timer pins for backlight PWM control without conflicting with touch channels.
推荐
USB HID Peripheral Devices
The PIC32MX230F064DT-V/PT implements USB HID class devices (keyboards, mice, game controllers, custom HID) using the on-chip USB 2.0 full-speed transceiver and 1 KB of dedicated USB RAM. At 40 MHz the MIPS32 M4K core handles HID report parsing, debouncing, and LED/RGB animations within the 1 ms USB frame budget. The 64 KB Flash accommodates USB stacks plus vendor-specific report descriptors.
推荐
Industrial Sensor Hubs
The PIC32MX230F064DT-V/PT aggregates data from multiple sensors via I2C/SPI buses and forwards them via USB CDC or UART. Two I2C buses plus two SPIs allow simultaneous connection of a 9-DoF IMU, environmental sensor, and external ADC without bus contention. The 1 ns timer resolution enables precise timestamping for vibration and flow metering, and the -V temperature grade supports outdoor and factory-floor deployments.
推荐
推荐产品汇总
工程参考数据： PIC32MX230F064DT-V/PT ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PIC32MX230F064DT-I/PT | PIC32MX130F064DT-V/PT | PIC32MX220F032DT-V/PT | PIC32MX250F128DT-V/PT |
|---|---|---|---|---|---|
| Package | 44-pin TQFP (10x10 mm) | 44-pin TQFP (10x10 mm) - same | 44-pin TQFP (10x10 mm) - same | 44-pin TQFP (10x10 mm) - same | 44-pin TQFP (10x10 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 64 KB | 64 KB | 64 KB | 32 KB (-50%) | 128 KB (+100%) |
| SRAM | 16 KB | 16 KB | 16 KB | 8 KB (-50%) | 32 KB (+100%) |
| Maximum Clock | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 50 MHz (+25%) |
| Temperature Grade | Automotive -V (-40C to +105C) | Industrial -I (-40C to +85C) | Automotive -V (-40C to +105C) | Automotive -V (-40C to +105C) | Automotive -V (-40C to +105C) |
| USB 2.0 FS | Yes (OTG) | Yes (OTG) | No | Yes (OTG) | Yes (OTG) |
| Parallel Master Port (PMP) | Yes | Yes | No | Yes | Yes |
关键差异点
- USB 2.0 full-speed OTG with integrated transceiver and AEC-Q100 -V automotive grade （对比 PIC32MX130F064DT-V/PT)
- Automotive-V temperature grade qualification (-40C to +105C, AEC-Q100) （对比 PIC32MX230F064DT-I/PT)
- PMP graphics interface and dual I2S blocks in 44-TQFP （对比 PIC32MX220F032DT-V/PT)
- 0.5 mA/MHz active current consumption with full peripheral set （对比 PIC32MX250F128DT-V/PT)
设计说明
Estimated: at 40 MHz active, typical core current is approximately 20 mA (0.5 mA/MHz x 40) plus USB and I/O drive. Total VDD budget is therefore around 25-30 mA. Add a 4.7 uF bulk capacitor and a 100 nF ceramic on each VDD/VSS pair within 5 mm of the pins. Use a low-noise LDO such as MCP1790-3002E for the analog AVDD rail if ADC accuracy below 1 LSB is required.
Route the USB D+/D- pair as a 90 ohm differential with matched length within 150 mil; keep total length under 50 mm and avoid splits in the reference plane below the traces. Place the 12 MHz crystal within 5 mm of OSC1/OSC2 with short traces and a grounded guard ring. The 44-TQFP thermal pad is not present; a copper pour under the package tied to VSS improves EMI performance by 2-4 dB.
Do not exceed 3.6 V on any pin including during hot-plug events on USB VBUS. MCLR must have a 10 kohm pull-up and a 100 nF capacitor to ground for proper reset; missing the capacitor causes spurious resets during ESD strikes. When using PPS, lock the PPS registers before sleep mode or peripheral mapping will reset on wake. For automotive -V grade designs, validate that your firmware complies with ISO 26262 ASIL requirements independently - the part itself is AEC-Q100 qualified, not ASIL rated.
Estimated: at 25 C ambient with continuous 40 MHz operation and full USB activity, junction temperature rise is approximately 25 C (using Microchip thermal model theta_JA = 60 C/W for 44-TQFP 4-layer JEDEC board). At +105 C automotive ambient this yields Tj of +130 C - within the +150 C max but with minimal margin. For continuous high-activity designs, consider the larger 64-pin variants with better thermal dissipation.
合规信息
RoHS compliant per Microchip product page. AEC-Q100 qualified for automotive applications per -V suffix. Lead-free reflow-compatible up to 260 C peak. Not specifically ASIL-rated; functional safety analysis is the integrator's responsibility.