S912XEQ512F0CAL - 16-bit 50MHz 512KB Flash MCU | NXP Automotive
料号： S912XEQ512F0CAL ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $12.4 | $12.40 |
| 10 | $11.16 | $111.60 |
| 100 | $9.92 | $992.00 |
| 500 | $8.68 | $4,340.00 |
| 1,000 | $7.44 | $7,440.00 |
S912XEQ512F0CAL 概述
A microcontroller (MCU) is a single integrated circuit that combines a processor core, program memory, data memory, and peripherals such as timers, ADCs, and communication interfaces on one die. Within the power-management and embedded control hierarchy, the HCS12X family belongs to the 16-bit microcontroller class positioned between 8-bit MCUs and 32-bit automotive processors, making it a widely used mid-range solution for real-time embedded control.
Key features of the S912XEQ512F0CAL include the XGATE co-processor, which acts as a programmable DMA-driven RISC engine that offloads interrupt handling and I/O tasks from the main S12X CPU, effectively boosting overall system throughput. Additional features include flexible, programmable hardware-emulated EEPROM, a memory protection unit (MPU) with supervisor and user modes for system integrity, a 12-bit ADC with 3 us conversion time, an enhanced capture timer (ECT), a periodic interrupt timer (PIT), and a real-time interrupt (RTI).
Technically, the device is based on the S12X CPU core operating from a 5V supply rail (with 1.8V/2.8V internal domains per distributor data), which gives it excellent EMC robustness and noise immunity compared with finer-geometry 3.3V or 1.8V-only processes. This is a significant advantage in the electrically harsh environments of vehicles and industrial machinery where high-voltage transients, load dump, and switching noise are common.
Typical applications include body control modules, gateway modules, instrument clusters, HVAC controls, and general automotive/industrial real-time control systems. The large 512 KB Flash accommodates complex diagnostic stacks such as UDS, while the XGATE co-processor handles CAN and LIN communication stacks concurrently with the main application.
A key design consideration is clock configuration: the 50 MHz bus speed is achieved with an internal PLL from an external crystal, so designers must carefully follow NXP layout and decoupling guidance for the PLL loop filter to meet EMC requirements.
This page synthesizes distributor inventory and pricing data, drop-in same-family alternatives, design notes, and a detailed comparison table not found on the manufacturer product page alone.
直接替换替代料： S912XEQ512F0CAL ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： S912XEQ512F0CAL （相同外形与封装尺寸） ——差异在于 Operating Temperature, Package, Timers, Core Processor, EEPROM.
快速对比工具——选择替代料号进行并排对比：
MC9S12XEP768CAG
✅ 直接替换✓ 有现货
$19.85 / 个
查看数据手册 →MC9S12XEQ384CAG
✅ 直接替换✓ 有现货
联系询价
查看数据手册 →MC9S12XDT512MAA
✅ 直接替换✓ 有现货
联系询价
查看数据手册 →MC9S12XDT256CAG
✅ 直接替换✓ 有现货
$17.4 / 个
查看数据手册 →S912XEQ512F0CALR
✅ 直接替换📋 参考替代料（不在目录中）
S912XEQ512F0CAL 最大额定值与电气特性
| Core Processor | HCS12X (S12X core with XGATE co-processor) |
| Core Size | 16-Bit |
| Bus Speed | 50 MHz |
| Program Flash Memory | 512 KB (512K x 8) |
| EEPROM | Hardware-emulated, flexible programmable |
| ADC Resolution | 12-bit |
| ADC Conversion Time | 3 us |
| Timers | Enhanced Capture Timer (ECT), Periodic Interrupt Timer (PIT), Real Time Interrupt (RTI) |
| Memory Protection | MPU with supervisor/user modes |
| 电源电压 | 1.8 V / 2.8 V / 5 V |
| 工作温度 | -40C to +85C |
| 封装 | 112-LQFP (20 x 20 mm), gull-wing terminals, square body |
| 安装类型 | Surface Mount |
| Qualification | Automotive Qualified, AEC-Q100 |
| Packaging | Tray |
| Peripherals | DMA (XGATE), LVD, POR, PWM |
S912XEQ512F0CAL 112-lqfp (20 x 20 mm), gull-wing terminals, square body 引脚配置指南
S912XEQ512F0CAL（112-lqfp (20 x 20 mm), gull-wing terminals, square body 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： S912XEQ512F0CAL.
请参阅 数据手册 以查看完整引脚配置。
典型应用
S912XEQ512F0CAL 适用于 6 应用s: Body Control Module (BCM), Vehicle Gateway Module, Instrument Cluster, HVAC Control, Industrial Real-Time Control, Engine Management Auxiliary Controllers.
Body Control Module (BCM)
The S912XEQ512F0CAL fits body control modules because its 50 MHz S12X core with 512 KB Flash can host lamp control, wiper logic, central locking, and UDS diagnostic stacks simultaneously, while the XGATE co-processor services CAN and LIN frames without stealing main-CPU cycles. The 5V-based I/O structure withstands the load-dump and transient conditions typical of vehicle harnesses, and the 12-bit ADC with 3 us conversion time reads switch matrices and analog sensor inputs with adequate margin. Designers typically allocate the ECT for PWM lamp dimming and the PIT for task scheduling, using hardware-emulated EEPROM to store configuration and fault data across power cycles.
推荐
Vehicle Gateway Module
In gateway modules that route messages between multiple CAN channels and LIN, the S912XEQ512F0CAL's XGATE co-processor acts as a programmable DMA engine that moves CAN buffers and performs message filtering in parallel with the main CPU, preserving real-time latency even under full bus load. The 512 KB Flash accommodates routing tables, gateway firmware, and OTA-style bootloader code, and the MPU with supervisor/user modes helps isolate application firmware from communication stacks for system integrity. Its -40C to +85C automotive qualification and 5V core tolerance suit under-dash and engine-bay mounting locations where supply transients and thermal cycling are routine.
推荐
Instrument Cluster
Instrument clusters require deterministic stepper-motor pointer control, backlight dimming, and buzzer output - all supported by the S912XEQ512F0CAL's enhanced capture timer (ECT) channels used in PWM mode. The 12-bit ADC with 3 us conversion digitizes fuel-level, temperature, and battery-voltage inputs quickly enough for filtering across multiple samples, improving gauge accuracy. With 512 KB Flash, the firmware can include odometer persistence in emulated EEPROM, warning-chime sequences, and a CAN stack for receiving vehicle-speed messages via XGATE offload. The automotive AEC-Q100 qualification covers the -40C to +85C cabin and near-engine ambient ranges typical of cluster installations.
推荐
HVAC Control
Automotive HVAC controllers benefit from the S912XEQ512F0CAL's combination of rich analog input and timer output resources: the 12-bit ADC reads cabin and duct temperature sensors (NTC networks) with 3 us conversions enabling aggressive oversampling, while ECT PWM channels drive blower motors and blend-door servo motors. Hardware-emulated EEPROM retains learned door-position calibration and fault codes without external memory. The XGATE co-processor runs the LIN communication with the panel head unit, freeing the 50 MHz S12X core for control-loop execution. Its 5V process tolerates the noisy supply environment created by blower motor commutation, reducing external filtering cost.
推荐
Industrial Real-Time Control
Beyond automotive, the S912XEQ512F0CAL serves industrial control nodes needing deterministic 16-bit control: the 50 MHz bus executes PID loops with microseconds of headroom, the ECT captures encoder pulses for position feedback, and the 12-bit ADC samples analog transducers at 3 us per conversion. Its wide -40C to +85C operating range and robust 5V architecture tolerate factory-floor electrical noise that would challenge finer-geometry 3.3V MCUs. The MPU with supervisor/user modes supports partitioned firmware for functional safety hygiene, and emulated EEPROM stores parameter sets and production data. The 512 KB Flash is sufficient for protocol stacks (CANopen-style logic) alongside the application.
推荐
Engine Management Auxiliary Controllers
For auxiliary engine-management functions such as electronic throttle positioners, exhaust-gas recirculation actuators, or fan-speed controllers, the S912XEQ512F0CAL provides real-time PWM generation through the ECT, feedback digitization through the 12-bit ADC, and robust 5V I/O for position-sensor ratiometric inputs. The XGATE co-processor handles CAN diagnostics (UDS) while the main CPU closes the actuator control loop at high rate, and the periodic interrupt timer (PIT) provides deterministic task scheduling. AEC-Q100 automotive qualification and 512 KB of Flash for adaptive-control calibration tables make the EQ512 a natural fit for these mid-complexity powertrain auxiliaries, complementing a main 32-bit engine ECU.
推荐
推荐产品汇总
工程参考数据： S912XEQ512F0CAL ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MC9S12XEP768CAG | MC9S12XEQ384CAG | MC9S12XDT512MAA | MC9S12XDT256CAG |
|---|---|---|---|---|---|
| Package | 112-LQFP (20 x 20 mm) | 112-LQFP - same | 112-LQFP - same | 112-LQFP - same | 112-LQFP - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core / Bus Speed | HCS12X, 50 MHz | HCS12X, 50 MHz | HCS12X, 50 MHz | HCS12X, 50 MHz | HCS12X, 50 MHz |
| Program Flash | 512 KB | 768 KB | 384 KB | 512 KB | 256 KB |
| XGATE Co-processor | Yes | Yes | Yes | Yes | Yes |
| ADC | 12-bit, 3 us conversion | 12-bit | 12-bit | 12-bit | 12-bit |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Automotive Qualification | Yes (AEC-Q100) | Yes | Yes | Yes | Yes |
关键差异点
- Largest mainstream Flash in same 112-LQFP footprint （对比 MC9S12XEQ384CAG)
- XGATE co-processor parallelism （对比 MC9S12XDT256CAG)
- 5V-core EMC robustness （对比 SPC5644AF0MLU2)
- MPU with supervisor/user modes （对比 MC9S12XDT512MAA)
设计说明
The S912XEQ512F0CAL runs from a 5V primary supply with internal 1.8V/2.8V domains per distributor data. Provide a single low-ESR 5V rail with bulk (10 uF) plus per-pin 0.1 uF ceramic decoupling, and keep the VDDA/VSSA analog supply isolated with an RC or ferrite filter so the 12-bit ADC achieves its rated 3 us conversion accuracy. NXP S12X reference designs (e.g., the S12XE evaluation boards) show the recommended supply filtering topology; follow the datasheet's power chapter values exactly.
The 50 MHz bus is generated by the internal PLL from a lower-frequency crystal. Place the crystal, load capacitors, and PLL loop-filter components within a few millimeters of the device, over a solid ground plane, and keep the PLL filter node free of digital return currents. Poor PLL layout is the most common root cause of radiated-emission failures and jitter in S12X boards. NXP application guidance for the S12X family recommends guarding the oscillator area and avoiding routing high-di/dt signals under the filter components.
Several S12X package options share the same base part number family but differ in pin count and peripheral multiplexing - verify the 112-LQFP pin assignment for your exact suffix (F0CAL) against the datasheet pin tables before layout sign-off. Also confirm RAM and D-Flash/EEPROM partition sizes when migrating between EQ512, EQ384, and XEP768 options: while pin-compatible, emulated EEPROM sector sizes differ across memory options and affect your data-retention driver configuration.
On a 50 MHz bus with a 16-bit external-visible parallel activity, keep address/data trace stubs short and match lengths where the bus is heavily loaded. For CAN interfaces driven through the XGATE offload, place the CAN transceiver close to the MCU with a common-mode choke and split termination per the transceiver vendor reference design. The 5V I/O structure is tolerant, but series resistors (typically 33-100 ohm) on long harness-connected lines reduce ESD stress on the pins.
合规信息
Automotive qualified per NXP product page and Arrow listing (AEC-Q100). RoHS/REACH/lead-free status not stated in the provided data - check the NXP product page Environmental Quality section.
