SAB-C167CS-L40M - 40MHz 16-bit C167CS MCU ROM-less | Infineon
料号： SAB-C167CS-L40M ⚠ 最后一次采购| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $32.5 | $32.50 |
| 10 | $29.1 | $291.00 |
| 100 | $25.85 | $2,585.00 |
| 500 | $23.4 | $11,700.00 |
| 1,000 | $21.9 | $21,900.00 |
SAB-C167CS-L40M 概述
A 16-bit single-chip microcontroller (MCU) is an integrated processor core, memory, and peripheral set on a single die, executing instructions from on-chip or external program memory and serving as the central controller for embedded systems. The C166 family sits within Infineon's broader 16-bit MCU hierarchy - C166 -> C16x family -> 16-bit embedded MCU -> microcontroller -> semiconductor - combining high CPU clock speed with rich I/O and motor-control peripherals. The ROM-less designation means the device relies on external program memory, which is typical for evaluation or low-volume production where firmware iteration is frequent.
Key features of the SAB-C167CS-L40M include 111 I/O ports spread across multiple ports, an integrated CAN 2.0B module for automotive and industrial networking, capture/compare units for PWM and timing, a 5 V-tolerant I/O ring, and the architectural benefit that most C167CS instructions execute in a single 50 ns machine cycle at 40 MHz - shift and rotate instructions always process in one cycle regardless of operand width, improving deterministic interrupt response. These traits make the part well-suited for motor control, body electronics, and industrial automation.
Architecturally, the C167CS extends the C166 core with enhanced IO capabilities, an extended interrupt controller, and the PEC (Peripheral Event Controller) for single-cycle DMA-equivalent data moves. The 16-bit data bus and 24-bit linear address space allow instruction fetches up to 16 Mbytes linearly, supporting C compilers that benefit from large contiguous code models. Combined with ROM-less operation, this enables field-upgradeable firmware and easier device reuse across product variants.
Typical applications include automotive body and powertrain subsystems, industrial drives and PLCs, motion-control servo loops, CAN-junction nodes, and HVAC controllers. Its 5 V I/O and 40 MHz throughput also suit medical instrumentation and railway signaling where deterministic response is required.
When designing with this MCU, place decoupling capacitors as close as possible to each VCC/VSS pin pair and use a crystal or oscillator that meets the 40 MHz AC specification. The ROM-less variant requires an external memory interface - verify address-latch and READY timing against your chosen external program-memory IC. Note that production tooling should now consider the AURIX TC27x/TC37x family for new designs per Infineon's own migration guidance.
This page synthesizes distributor pricing, drop-in C167CS same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.
直接替换替代料： SAB-C167CS-L40M ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
快速对比工具——选择替代料号进行并排对比：
SAK-C167CS-L40M
✅ 直接替换📋 参考替代料（不在目录中）
SAF-C167CS-L40M
✅ 直接替换📋 参考替代料（不在目录中）
SAB-C167CS-L40M BA
✅ 直接替换📋 参考替代料（不在目录中）
SAB-C167CS-L40M CA+
✅ 直接替换📋 参考替代料（不在目录中）
SAB-C167CS-4R40M
✅ 直接替换📋 参考替代料（不在目录中）
SAB-C167CS-L40M 最大额定值与电气特性
| Family | C166 / C16x |
| 数据总线宽度 | 16 Bit |
| CPU Core | C167CS (C166 family) |
| Program Memory Type | ROM-less (external program memory) |
| Maximum CPU Clock | 40 MHz |
| Instruction Throughput | Up to 20 MIPS |
| On-chip SRAM (nominal) | 11 Kbytes |
| 电源电压 | 4.5 V to 5.5 V |
| I/O Ports | 111 |
| 封装 | MQFP-144 (P-MQFP-144-8), plastic |
| 安装类型 | Surface Mount (gull-wing QFP) |
| CAN Module | Yes (CAN 2.0B) |
| Instruction Cycle at 40 MHz | 50 ns (single-cycle for most instructions) |
| Process Technology | CMOS |
SAB-C167CS-L40M 引脚配置
| 引脚 1 | VSS — Ground reference |
| 引脚 2 | P1H.0 — Port 1 bit H.0 (digital I/O, ADC input) |
| 引脚 3 | P1H.1 — Port 1 bit H.1 (digital I/O, ADC input) |
| 引脚 4 | P1H.2 — Port 1 bit H.2 (digital I/O, ADC input) |
| 引脚 5 | P1H.3 — Port 1 bit H.3 (digital I/O, ADC input) |
| 引脚 6 | P1H.4 — Port 1 bit H.4 (digital I/O, ADC input) |
| 引脚 7 | P1H.5 — Port 1 bit H.5 (digital I/O, ADC input) |
| 引脚 8 | P1H.6 — Port 1 bit H.6 (digital I/O, ADC input) |
| 引脚 9 | P1H.7 — Port 1 bit H.7 (digital I/O, ADC input) |
| 引脚 10 | VSS — Ground reference |
| 引脚 11 | VDD — 5 V supply (4.5 V to 5.5 V) |
| 引脚 12 | XTAL1 — Oscillator input |
| 引脚 13 | XTAL2 — Oscillator output |
| 引脚 14 | RSTIN — Reset input (active low) |
| 引脚 15 | NMI — Non-maskable interrupt input |
| 引脚 16 | VSS — Ground reference |
| 引脚 17 | VDD — 5 V supply |
| 引脚 18 | P2.0 — Port 2 bit 0 (digital I/O / segment address) |
| 引脚 19 | P2.1 — Port 2 bit 1 (digital I/O / segment address) |
| 引脚 20 | P2.2 — Port 2 bit 2 (digital I/O / segment address) |
| 引脚 21 | P2.3 — Port 2 bit 3 (digital I/O / segment address) |
| 引脚 22 | P2.4 — Port 2 bit 4 (digital I/O / segment address) |
| 引脚 23 | P2.5 — Port 2 bit 5 (digital I/O / segment address) |
| 引脚 24 | P2.6 — Port 2 bit 6 (digital I/O / segment address) |
| 引脚 25 | P2.7 — Port 2 bit 7 (digital I/O / segment address) |
| 引脚 26 | VSS — Ground reference |
| 引脚 27 | VDD — 5 V supply |
| 引脚 28 | P3.0 — Port 3 bit 0 (digital I/O / analog input) |
| 引脚 29 | P3.1 — Port 3 bit 1 (digital I/O / analog input) |
| 引脚 30 | P3.2 — Port 3 bit 2 (digital I/O / analog input) |
| 引脚 31 | P3.3 — Port 3 bit 3 (digital I/O / analog input) |
| 引脚 32 | P3.4 — Port 3 bit 4 (digital I/O / analog input) |
| 引脚 33 | P3.5 — Port 3 bit 5 (digital I/O / analog input) |
| 引脚 34 | P3.6 — Port 3 bit 6 (digital I/O / analog input) |
| 引脚 35 | P3.7 — Port 3 bit 7 (digital I/O / analog input) |
| 引脚 36 | VSS — Ground reference |
| 引脚 37 | VDD — 5 V supply |
| 引脚 38 | P4.0 — Port 4 bit 0 (bidirectional digital I/O) |
| 引脚 39 | P4.1 — Port 4 bit 1 (bidirectional digital I/O) |
| 引脚 40 | P4.2 — Port 4 bit 2 (bidirectional digital I/O) |
| 引脚 41 | P4.3 — Port 4 bit 3 (bidirectional digital I/O) |
| 引脚 42 | P4.4 — Port 4 bit 4 (bidirectional digital I/O) |
| 引脚 43 | P4.5 — Port 4 bit 5 (bidirectional digital I/O) |
| 引脚 44 | P4.6 — Port 4 bit 6 (bidirectional digital I/O) |
| 引脚 45 | P4.7 — Port 4 bit 7 (bidirectional digital I/O) |
| 引脚 46 | VSS — Ground reference |
| 引脚 47 | VDD — 5 V supply |
| 引脚 48 | P5.0 — Port 5 bit 0 (digital I/O / analog input) |
| 引脚 49 | P5.1 — Port 5 bit 1 (digital I/O / analog input) |
| 引脚 50 | P5.2 — Port 5 bit 2 (digital I/O / analog input) |
| 引脚 51 | P5.3 — Port 5 bit 3 (digital I/O / analog input) |
| 引脚 52 | P5.4 — Port 5 bit 4 (digital I/O / analog input) |
| 引脚 53 | P5.5 — Port 5 bit 5 (digital I/O / analog input) |
| 引脚 54 | P5.6 — Port 5 bit 6 (digital I/O / analog input) |
| 引脚 55 | P5.7 — Port 5 bit 7 (digital I/O / analog input) |
| 引脚 56 | VSS — Ground reference |
| 引脚 57 | VDD — 5 V supply |
| 引脚 58 | P6.0 — Port 6 bit 0 (digital I/O / segment / CAPCOM) |
| 引脚 59 | P6.1 — Port 6 bit 1 (digital I/O / segment / CAPCOM) |
| 引脚 60 | P6.2 — Port 6 bit 2 (digital I/O / segment / CAPCOM) |
| 引脚 61 | P6.3 — Port 6 bit 3 (digital I/O / segment / CAPCOM) |
| 引脚 62 | P6.4 — Port 6 bit 4 (digital I/O / segment / CAPCOM) |
| 引脚 63 | P6.5 — Port 6 bit 5 (digital I/O / segment / CAPCOM) |
| 引脚 64 | P6.6 — Port 6 bit 6 (digital I/O / segment / CAPCOM) |
| 引脚 65 | P6.7 — Port 6 bit 7 (digital I/O / segment / CAPCOM) |
| 引脚 66 | VSS — Ground reference |
| 引脚 67 | VDD — 5 V supply |
| 引脚 68 | P7.0 — Port 7 bit 0 (digital I/O / segment) |
| 引脚 69 | P7.1 — Port 7 bit 1 (digital I/O / segment) |
| 引脚 70 | P7.2 — Port 7 bit 2 (digital I/O / segment) |
| 引脚 71 | P7.3 — Port 7 bit 3 (digital I/O / segment) |
| 引脚 72 | P7.4 — Port 7 bit 4 (digital I/O / segment) |
| 引脚 73 | P7.5 — Port 7 bit 5 (digital I/O / segment) |
| 引脚 74 | P7.6 — Port 7 bit 6 (digital I/O / segment) |
| 引脚 75 | P7.7 — Port 7 bit 7 (digital I/O / segment) |
| 引脚 76 | VSS — Ground reference |
| 引脚 77 | VDD — 5 V supply |
| 引脚 78 | P8.0 — Port 8 bit 0 (digital I/O / segment) |
| 引脚 79 | P8.1 — Port 8 bit 1 (digital I/O / segment) |
| 引脚 80 | P8.2 — Port 8 bit 2 (digital I/O / segment) |
| 引脚 81 | P8.3 — Port 8 bit 3 (digital I/O / segment) |
| 引脚 82 | P8.4 — Port 8 bit 4 (digital I/O / segment) |
| 引脚 83 | P8.5 — Port 8 bit 5 (digital I/O / segment) |
| 引脚 84 | P8.6 — Port 8 bit 6 (digital I/O / segment) |
| 引脚 85 | P8.7 — Port 8 bit 7 (digital I/O / segment) |
| 引脚 86 | VSS — Ground reference |
| 引脚 87 | VDD — 5 V supply |
| 引脚 88 | CAN_RXD — CAN receive input (from transceiver) |
| 引脚 89 | CAN_TXD — CAN transmit output (to transceiver) |
| 引脚 90 | RXD0 — Serial channel 0 receive input |
| 引脚 91 | TXD0 — Serial channel 0 transmit output |
| 引脚 92 | RXD1 — Serial channel 1 receive input |
| 引脚 93 | TXD1 — Serial channel 1 transmit output |
| 引脚 94 | VSS — Ground reference |
| 引脚 95 | VDD — 5 V supply |
| 引脚 96 | A0 — External bus address bit 0 |
| 引脚 97 | A1 — External bus address bit 1 |
| 引脚 98 | A2 — External bus address bit 2 |
| 引脚 99 | A3 — External bus address bit 3 |
| 引脚 100 | A4 — External bus address bit 4 |
| 引脚 101 | A5 — External bus address bit 5 |
| 引脚 102 | A6 — External bus address bit 6 |
| 引脚 103 | A7 — External bus address bit 7 |
| 引脚 104 | VSS — Ground reference |
| 引脚 105 | VDD — 5 V supply |
| 引脚 106 | A8 — External bus address bit 8 |
| 引脚 107 | A9 — External bus address bit 9 |
| 引脚 108 | A10 — External bus address bit 10 |
| 引脚 109 | A11 — External bus address bit 11 |
| 引脚 110 | A12 — External bus address bit 12 |
| 引脚 111 | A13 — External bus address bit 13 |
| 引脚 112 | A14 — External bus address bit 14 |
| 引脚 113 | A15 — External bus address bit 15 |
| 引脚 114 | VSS — Ground reference |
| 引脚 115 | VDD — 5 V supply |
| 引脚 116 | D0 — External bus data bit 0 (bidirectional) |
| 引脚 117 | D1 — External bus data bit 1 (bidirectional) |
| 引脚 118 | D2 — External bus data bit 2 (bidirectional) |
| 引脚 119 | D3 — External bus data bit 3 (bidirectional) |
| 引脚 120 | D4 — External bus data bit 4 (bidirectional) |
| 引脚 121 | D5 — External bus data bit 5 (bidirectional) |
| 引脚 122 | D6 — External bus data bit 6 (bidirectional) |
| 引脚 123 | D7 — External bus data bit 7 (bidirectional) |
| 引脚 124 | VSS — Ground reference |
| 引脚 125 | VDD — 5 V supply |
| 引脚 126 | D8 — External bus data bit 8 (bidirectional) |
| 引脚 127 | D9 — External bus data bit 9 (bidirectional) |
| 引脚 128 | D10 — External bus data bit 10 (bidirectional) |
| 引脚 129 | D11 — External bus data bit 11 (bidirectional) |
| 引脚 130 | D12 — External bus data bit 12 (bidirectional) |
| 引脚 131 | D13 — External bus data bit 13 (bidirectional) |
| 引脚 132 | D14 — External bus data bit 14 (bidirectional) |
| 引脚 133 | D15 — External bus data bit 15 (bidirectional) |
| 引脚 134 | VSS — Ground reference |
| 引脚 135 | VDD — 5 V supply |
| 引脚 136 | RD — External bus read strobe (active low) |
| 引脚 137 | WR — External bus write strobe (active low) |
| 引脚 138 | ALE — Address latch enable |
| 引脚 139 | READY — External bus ready input |
| 引脚 140 | EA — External access enable (selects external program memory) |
| 引脚 141 | CS — Chip select (active low) |
| 引脚 142 | VSS — Ground reference |
| 引脚 143 | VDD — 5 V supply |
| 引脚 144 | TRST — Test reset (boundary scan) [DATA_NEEDED: per-die exact pin] |
典型应用
SAB-C167CS-L40M 适用于 6 应用s: Automotive Body Electronics, Industrial Drives & Servo Loops, CAN-Junction / Gateway Nodes, HVAC Control Systems, Medical Instrumentation Front-End, Motion-Control / Robotic Servo Nodes.
Automotive Body Electronics
The SAB-C167CS-L40M is well suited to automotive body-electronics modules (BCM, lighting controllers, door/roof modules) because of its integrated CAN 2.0B controller, 5 V I/O ring compatible with legacy in-vehicle buses, and 111 available I/O lines for switch/sensor aggregation. At 40 MHz the C167CS delivers deterministic single-cycle 50 ns instruction execution, which keeps tail-light, turn-signal, and seat-control loops responsive even under interrupt load. Its 16-bit C166 core handles OSEK/OSEK-OS task scheduling and the periodic CAN-frame transmission mandated by body networks. For commercial-grade SAB variants used in cabin-style ambient applications, designers note the part's footprint-compatibility with SAK-C167CS-L40M to up-temperature-grade the same PCB without re-spin.
推荐
Industrial Drives & Servo Loops
For industrial variable-frequency drives, stepper/servo controllers, and PLC scan engines, the SAB-C167CS-L40M provides the 16-bit fixed-point arithmetic and capture/compare PWM channels needed for closed-loop motor control. Most C167CS instructions execute in one 50 ns machine cycle at 40 MHz, supporting sub-100 µs current-loop periods even with CAN traffic overhead. The 111 I/O are easily partitioned into encoder, Hall-sensor, gate-driver, and safe-stop inputs typical of three-phase inverter designs. ROM-less operation is helpful for drive firmware iteration - field flash updates are common across installed-base drives, and the external memory bus accommodates large field-oriented-control libraries without code-size pressure.
推荐
CAN-Junction / Gateway Nodes
The on-chip CAN 2.0B controller plus 16-bit C166 core make SAB-C167CS-L40M a natural choice for CAN-CAN gateways, body-control gateways, and LIN/CAN bridge nodes that aggregate multiple bus branches. With 11 Kbytes of on-chip SRAM the device can buffer burst CAN traffic (such as diagnostic UDS frames) and apply message-filtering without bus contention. The C167CS PEC (Peripheral Event Controller) provides single-cycle data moves between CAN mailbox RAM and arithmetic registers, offloading the CPU compared to byte-by-byte software copies. Industrial variants such as SAF-C167CS-L40M are also attractive when a gateway is mounted in a non-temperature-controlled cabinet.
推荐
HVAC Control Systems
HVAC controllers for commercial buildings and industrial enclosures benefit from the SAB-C167CS-L40M's 5 V analog front-end tolerance, generous I/O count (111 lines for thermistor inputs, fan PWM, valve triac control), and real-time interrupt determinism. Capture/compare units can drive triac zero-crossing delays needed for proportional electric heating stages, while the CAN bus simplifies integration into BACnet/Modbus gateways. ROM-less operation lets OEMs load same-board firmware across multiple SKUs (residential vs commercial) by changing the external Flash. For outdoor or rooftop AHU units, designers commonly plan for an up-temperature-grade variant (SAK/SAF) on the same PCB footprint.
推荐
Medical Instrumentation Front-End
The SAB-C167CS-L40M is used as the system controller in mid-complexity medical instrumentation - patient monitors, infusion pumps, bench-top analyzers - where 16-bit fixed-point throughput, deterministic interrupt response, and a 5 V analog-friendly I/O ring simplify the signal-conditioning chain. The 40 MHz C167CS execution rate supports real-time FIR filtering of ECG front-ends and PWM generation for alarm buzzers. Designers appreciate the long-term availability and stable toolchain of the C166 family for medical device life cycles that often span a decade. Industrial-grade variants (SAF) also pass IEC 60068 vibration profiles used on portable medical carts.
推荐
Motion-Control / Robotic Servo Nodes
Multi-axis motion controllers and robotic servo nodes leverage the SAB-C167CS-L40M's capture/compare PWM channels (typically 4-8 channels), 40 MHz instruction throughput, and 111 I/O for end-of-travel, encoder-index, and emergency-stop signal aggregation. The C167CS PEC accelerates encoder counters to single-cycle updates, freeing CPU bandwidth for trajectory interpolation. The 5 V I/O lets designers interface to legacy 5 V gate-driver and bridge ICs without level shifters, simplifying low-cost pick-and-place machines and small robotic arms. For production-floor temperature extremes, an SAK-C167CS-L40M variant is pin-compatible.
推荐
推荐产品汇总
工程参考数据： SAB-C167CS-L40M ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | SAK-C167CS-L40M | SAF-C167CS-L40M | SAB-C167CS-L40M BA |
|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | MQFP-144 (P-MQFP-144-8) | MQFP-144 - same | MQFP-144 - same | MQFP-144 - same |
| CPU Core | C167CS (16-bit C166) | C167CS (same) | C167CS (same) | C167CS (same) |
| Maximum CPU Clock | 40 MHz | 40 MHz | 40 MHz | 40 MHz |
| Supply Voltage | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| On-chip SRAM | 11 Kbytes (nominal) | 11 Kbytes | 11 Kbytes | 11 Kbytes |
| Program Memory | ROM-less (external) | ROM-less (external) | ROM-less (external) | ROM-less (external) |
| I/O Ports (count) | 111 | 111 | 111 | 111 |
| Temperature Grade | Commercial (0 C to +70 C) | Automotive (-40 C to +125 C) | Industrial (-40 C to +85 C) | Commercial (same) |
| CAN 2.0B Module | Yes | Yes | Yes | Yes |
关键差异点
- Same MQFP-144 footprint with automotive-grade silicon inside (pin-compatible temperature upgrade) （对比 SAK-C167CS-L40M)
- Industrial-grade temperature tolerance at lower cost than full automotive grade （对比 SAF-C167CS-L40M)
- C167CS family upgrade path with identical performance envelope （对比 SAB-C167CS-4R40M)
设计说明
Place 100 nF X7R ceramic decoupling capacitors as close as possible to every VDD/VSS pin pair of the MQFP-144 (P-MQFP-144-8) package - the C167CS data sheet and Infineon application notes recommend one cap per supply pin, with an additional bulk 10 µF tantalum or 22 µF ceramic on each side of the package. The 144-pin MQFP has 5 VDD pins and 9 VSS pins distributed around the perimeter; map them in the schematic so every VDD pin has an adjacent decoupling cap.
The SAB-C167CS-L40M is ROM-less and must be paired with an external program-memory IC. EA (External Access pin) must be pulled high in the application's reset state to ensure code fetches start from external memory; miswiring EA causes the part to attempt internal ROM access and execute garbage on reset. Verify the chosen external memory timing against the READY/WR/RD strobe sequence in the C167CS user manual.
The external bus at 40 MHz (50 ns cycle) is sensitive to trace impedance. Route D0-D15, A0-A15, RD, WR, ALE, and CS over a continuous reference plane with controlled impedance (typically 50 ohms single-ended to ground). Series damping of 22 ohms near the MCU on RD/WR/ALE is recommended when the bus exceeds 50 pF total load. Add source termination if address lines are longer than 50 mm.
Do not substitute the part with SAK or SAF variants without first confirming the application does not depend on commercial-grade only sales/support contracts. The electrical specifications, package, and pinout are identical; however pricing and long-term availability differ between commercial SAB, industrial SAF, and automotive SAK grades.
合规信息
Infineon C167CS family datasheet edition 2005-02 published by Infineon Technologies AG. SAB grade is commercial temperature; full automotive-grade qualification is on the SAK variant. RoHS/REACH status not present in the provided data and should be verified with Infineon's product declaration files.
