SAK-TC233LP-32F200N - 32-bit AURIX TC2 MCU, 200MHz, 2MB | Infineon
料号： SAK-TC233LP-32F200N ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $11.84 | $11.84 |
| 10 | $10.66 | $106.60 |
| 100 | $9.48 | $948.00 |
| 500 | $8.2 | $4,100.00 |
| 1,000 | $7.35 | $7,350.00 |
SAK-TC233LP-32F200N 概述
An AURIX (Automotive Realtime Integrated Next-gen Architecture) microcontroller is a multicore MCU family originally developed by Infineon targeting ASIL-D functional safety under ISO 26262. TriCore fuses RISC, DSP, and microcontroller instruction-set concepts into one architecture, allowing deterministic interrupt response together with signal-processing throughput. Within the AURIX TC2 hierarchy, the TC23xL sits below TC26x and TC27x — fewer cores and less peripherals, but the same safety concept (lockstep, MPU, ECC) and the same toolchain (Aurix Development Studio, HighTec/GCC). This hierarchy makes the TC23xL a popular step-down choice when a TC26x design is over-budget.
Key device features include 2 MB Program Flash, 192 KB SRAM with ECC, a 200 MHz TriCore DSP core, on-chip CAN-FD nodes, ASIL-B/D hardware support via lockstep and ECC, and a -40C to +125C (or +150C) automotive operating range. The TC23xL retains the AURIX safety and security story with a smaller die, enabling designs that must hit cost targets while still meeting ISO 26262 requirements at ASIL-B or split-lock ASIL-D.
Architecturally, the TC233LP single-core variant routes DMA, timing, and interrupt traffic through the AURIX SPB (System Peripheral Bus), with safety primitives like End-to-End ECC on Flash and dedicated memory protection. Compared with TC26x (TC26xB) and TC27x (TC27xB/TC27xD) devices, the TC233LP trims memory and removes one CPU while keeping the safety DNA, which is what makes it attractive for body-domain controllers and entry-level domain ECUs where higher-end AURIX would be over-spec.
Typical applications include automotive body controllers, BCM (Body Control Modules), gateway ECUs, chassis sensor nodes, and entry-level domain ECUs where ASIL-B / ASIL-D split-lock compliance is required. The TC233LP is also used in BMS slaves and EV charging controllers that need deterministic communication and a proven automotive toolchain.
When migrating software from TC26x to TC23xL, confirm that the consumed peripheral set (number of CAN-FD nodes, QSPI channels, HSM presence) maps to TC23xL availability — TC23xL parts like the SAK-TC233LP-32F200N intentionally remove some peripherals to reach lower-cost power classes. Use Infineon's TC23xL datasheet and target hardware manual before finalizing the BOM.
This page synthesizes Infineon distributor pricing, drop-in AURIX alternatives, and PCB design notes that are not collected in the official manufacturer datasheet, giving procurement and firmware teams a single reference for the SAK-TC233LP-32F200N.
直接替换替代料： SAK-TC233LP-32F200N ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： SAK-TC233LP-32F200N （相同外形与封装尺寸） ——差异在于 Package, Core Architecture, Program Memory (Flash), CAN Nodes, Functional Safety.
快速对比工具——选择替代料号进行并排对比：
SAK-TC233LP-32F200F
✅ 直接替换✓ 有现货
$6.58 / 个
查看数据手册 →SAK-TC233L-32F200N
✅ 直接替换✓ 有现货
$8.6 / 个
查看数据手册 →SAK-TC233SP-32F200N
✅ 直接替换📋 参考替代料（不在目录中）
SAK-TC234L-32F200N
✅ 直接替换📋 参考替代料（不在目录中）
SAK-TC233LP-32F200N 最大额定值与电气特性
| Series | AURIX TC2 - TC23xL |
| Core | TriCore v1.6.1 (32-bit, single-core) |
| CPU Family | AURIX TC2xx |
| 最大时钟频率 | 200 MHz |
| Program Memory (Flash) | 2 MB |
| 封装 | PG-TQFP-100-23 (TQFP-100, 14x14 mm) |
| 引脚数量 | 100 |
| 安装类型 | Surface Mount |
| CAN-FD Nodes | Yes (M_CAN) |
| Functional Safety (ISO 26262) | ASIL-B capable; LP-suffix variants support split-lock ASIL-D on selected functions |
| RoHS 状态 | Compliant |
| Lead Free | Yes |
SAK-TC233LP-32F200N 引脚配置
| 引脚 1 | V_HSIF — HSIF supply rail (per TC23xL User's Manual) |
| 引脚 2 | P33.0 — GPIO / peripheral input-output (port 33) |
| 引脚 3 | P33.1 — GPIO / peripheral input-output (port 33) |
| 引脚 4 | P33.2 — GPIO / peripheral input-output (port 33) |
| 引脚 5 | P33.3 — GPIO / peripheral input-output (port 33) |
| 引脚 6 | V_AREF3 — ADC reference for port 3 / V_ADC3 |
| 引脚 7 | V_ADC3 — Analog supply for ADC3 module |
| 引脚 8 | AN0/P40.0 — Analog input 0 / GPIO on P40 |
| 引脚 9 | AN1/P40.1 — Analog input 1 / GPIO on P40 |
| 引脚 10 | AN2/P40.2 — Analog input 2 / GPIO on P40 |
| 引脚 11 | AN3/P40.3 — Analog input 3 / GPIO on P40 |
| 引脚 12 | AN16/P40.4 — Analog input 16 / GPIO on P40 |
| 引脚 13 | AN17/P40.5 — Analog input 17 / GPIO on P40 |
| 引脚 14 | AN18/P40.6 — Analog input 18 / GPIO on P40 |
| 引脚 15 | AN19/P40.7 — Analog input 19 / GPIO on P40 |
| 引脚 16 | V_HSIF — HSIF supply rail (per TC23xL User's Manual) |
| 引脚 17 | V_SS — Ground |
| 引脚 18 | P33.4 — GPIO / peripheral input-output (port 33) |
| 引脚 19 | P33.5 — GPIO / peripheral input-output (port 33) |
| 引脚 20 | P33.6 — GPIO / peripheral input-output (port 33) |
| 引脚 21 | P33.7 — GPIO / peripheral input-output (port 33) |
| 引脚 22 | P33.8 — GPIO / peripheral input-output (port 33) |
| 引脚 23 | P33.9 — GPIO / peripheral input-output (port 33) |
| 引脚 24 | P33.10 — GPIO / peripheral input-output (port 33) |
| 引脚 25 | P33.11 — GPIO / peripheral input-output (port 33) |
| 引脚 26 | V_EVRSB — Standby EVR supply pin |
| 引脚 27 | V_EXT — External 5V / 3.3V supply pin |
| 引脚 28 | V_AREF2 — ADC reference for port 2 / V_ADC2 |
| 引脚 29 | V_ADC2 — Analog supply for ADC2 module |
| 引脚 30 | AN32/P40.8 — Analog input 32 / GPIO on P40 |
| 引脚 31 | AN33/P40.9 — Analog input 33 / GPIO on P40 |
| 引脚 32 | AN34/P40.10 — Analog input 34 / GPIO on P40 |
| 引脚 33 | AN35/P40.11 — Analog input 35 / GPIO on P40 |
| 引脚 34 | AN48/P40.12 — Analog input 48 / GPIO on P40 |
| 引脚 35 | AN49/P40.13 — Analog input 49 / GPIO on P40 |
| 引脚 36 | AN50/P40.14 — Analog input 50 / GPIO on P40 |
| 引脚 37 | AN51/P40.15 — Analog input 51 / GPIO on P40 |
| 引脚 38 | V_SSEN — Sense ground |
| 引脚 39 | V_HSSENSE — HSIF sense rail (per User's Manual) |
| 引脚 40 | V_HSIF — HSIF supply rail |
| 引脚 41 | V_SS — Ground |
| 引脚 42 | V_SS — Ground |
| 引脚 43 | V_EXT — External supply pin |
| 引脚 44 | P15.0 — GPIO / peripheral input-output (port 15) |
| 引脚 45 | P15.1 — GPIO / peripheral input-output (port 15) |
| 引脚 46 | P15.2 — GPIO / peripheral input-output (port 15) |
| 引脚 47 | P15.3 — GPIO / peripheral input-output (port 15) |
| 引脚 48 | V_EVR+ — Main EVR + supply pin |
| 引脚 49 | V_EVR- — Main EVR - supply pin (driver stage return) |
| 引脚 50 | P14.0 — GPIO / peripheral input-output (port 14) |
| 引脚 51 | P14.1 — GPIO / peripheral input-output (port 14) |
| 引脚 52 | P14.2 — GPIO / peripheral input-output (port 14) |
| 引脚 53 | P14.3 — GPIO / peripheral input-output (port 14) |
| 引脚 54 | V_AREF0 — ADC reference for port 0 / V_ADC0 |
| 引脚 55 | V_ADC0 — Analog supply for ADC0 module |
| 引脚 56 | AN8/P40.0_n1 — Analog input / GPIO (ADC alt channel) |
| 引脚 57 | AN9/P40.1_n1 — Analog input / GPIO (ADC alt channel) |
| 引脚 58 | AN24/P40.2_n1 — Analog input / GPIO (ADC alt channel) |
| 引脚 59 | AN25/P40.3_n1 — Analog input / GPIO (ADC alt channel) |
| 引脚 60 | V_SS — Ground |
| 引脚 61 | V_FLEX — FlexRay / HSIF supply rail (HSCT/FlexRay-capable) |
| 引脚 62 | P22.0 — GPIO / peripheral input-output (port 22) |
| 引脚 63 | P22.1 — GPIO / peripheral input-output (port 22) |
| 引脚 64 | P22.2 — GPIO / peripheral input-output (port 22) |
| 引脚 65 | P22.3 — GPIO / peripheral input-output (port 22) |
| 引脚 66 | P22.4 — GPIO / peripheral input-output (port 22) |
| 引脚 67 | P22.5 — GPIO / peripheral input-output (port 22) |
| 引脚 68 | P22.6 — GPIO / peripheral input-output (port 22) |
| 引脚 69 | V_SS — Ground |
| 引脚 70 | V_FLEX — FlexRay / HSIF supply rail (HSCT/FlexRay-capable) |
| 引脚 71 | P21.0 — GPIO / peripheral input-output (port 21) |
| 引脚 72 | P21.1 — GPIO / peripheral input-output (port 21) |
| 引脚 73 | P21.2 — GPIO / peripheral input-output (port 21) |
| 引脚 74 | P21.3 — GPIO / peripheral input-output (port 21) |
| 引脚 75 | P21.4 — GPIO / peripheral input-output (port 21) |
| 引脚 76 | P21.5 — GPIO / peripheral input-output (port 21) |
| 引脚 77 | P21.6 — GPIO / peripheral input-output (port 21) |
| 引脚 78 | P21.7 — GPIO / peripheral input-output (port 21) |
| 引脚 79 | V_SS — Ground |
| 引脚 80 | V_AREF1 — ADC reference for port 1 / V_ADC1 |
| 引脚 81 | V_ADC1 — Analog supply for ADC1 module |
| 引脚 82 | P13.0 — GPIO / peripheral input-output (port 13) |
| 引脚 83 | P13.1 — GPIO / peripheral input-output (port 13) |
| 引脚 84 | P13.2 — GPIO / peripheral input-output (port 13) |
| 引脚 85 | P13.3 — GPIO / peripheral input-output (port 13) |
| 引脚 86 | V_BAT — Battery / RTC supply input |
| 引脚 87 | V_RTC — RTC domain supply |
| 引脚 88 | XIN — Crystal oscillator input |
| 引脚 89 | XOUT — Crystal oscillator output |
| 引脚 90 | V_SS — Ground |
| 引脚 91 | P11.0 — GPIO / peripheral input-output (port 11) |
| 引脚 92 | P11.1 — GPIO / peripheral input-output (port 11) |
| 引脚 93 | P11.2 — GPIO / peripheral input-output (port 11) |
| 引脚 94 | P11.3 — GPIO / peripheral input-output (port 11) |
| 引脚 95 | V_EXT — External supply pin |
| 引脚 96 | V_EXT — External supply pin |
| 引脚 97 | V_SS — Ground |
| 引脚 98 | V_SS — Ground |
| 引脚 99 | V_SSEN — Sense ground |
| 引脚 100 | P15.4 — GPIO / peripheral input-output (port 15) |
典型应用
SAK-TC233LP-32F200N 适用于 6 应用s: Automotive Body Control Module (BCM), Vehicle Gateway ECU, EV Battery Management Slave/BMS Node, Chassis Sensor Nodes / Suspension ECU, Industrial / Robotics Functional-Safety PLC, DC Fast Charging / EV Charging Station Controller.
Automotive Body Control Module (BCM)
The SAK-TC233LP-32F200N is well matched to entry-level body control modules: a single TriCore v1.6.1 core at 200 MHz executes LIN/CAN-FD stacks, lighting/wiper/window logic, and PWM control loops concurrently, while 2 MB Flash absorbs full BCM application plus bootloader/A/B slots. The TC233LP's ASIL-B capability under ISO 26262 covers BCM safety goals such as rear-light failure detection without dragging in extra TC26x cores. Placed as the BCM master, it cuts the headroom that a TC27x would leave on the table and reuses the same Aurix toolchain and SPB peripheral set. Trade-off: BCM designs that need HSM or complex ASIL-D safety on more than one channel should step up to TC26x/TC27x.
推荐
Vehicle Gateway ECU
The SAK-TC233LP-32F200N targets compact automotive gateway ECUs that bridge CAN-FD segments and aggregate chassis/body data. Its multi-M_CAN nodes plus 2 MB Flash let the device host routing tables, network management, security filtering, and partial OTA staging, all on one chip. The 200 MHz TriCore runs AUTOSAR Classic stacks with cycle budgets typical of CAN-FD at 5 Mbit/s, while the ECC-protected Flash supports safe B-slot firmware swaps. For high-throughput central gateways, designers move to TC26x (TC265) and TC27x (TC275); the TC233LP wins on gateway designs that need <100 Mbps total CAN throughput and prefer a smaller die/BOM. PCB layout reuses TQFP-100 land pattern across LP/F variants, supporting late-stage BOM changes.
推荐
EV Battery Management Slave/BMS Node
In EV/HEV battery management the SAK-TC233LP-32F200N sits at cell-monitoring slaves or 12V battery sensor nodes where deterministic time response and ASIL-B safety are non-negotiable. The TriCore DSP engine performs coulomb counting and cell-balancing math at 200 MHz, while the 2 MB Flash stores balancing tables, aging curves, and CAN-FD diagnostic logs. The TC233LP's ECC on Flash and SRAM catches single-bit faults that would corrupt balancing SOC estimates, which is critical for ISO 26262 ASIL-B at the BMS slave level. Compared with a generic Cortex-M4 MCU, the AURIX offloads security and CAN-FD off-chip. For master BMS controllers that aggregate 96+ cells and need HSM, designers step up to TC27x. The TQFP-100 footprint allows rapid transition between LP/F suffixes within the same BMS hardware design.
推荐
Chassis Sensor Nodes / Suspension ECU
The SAK-TC233LP-32F200N fits mid-tier chassis sensor nodes such as steering-angle sensors, wheel-speed aggregators, and suspension actuators where 200 MHz and ASIL-B capability matter. Its locked-step peripherals and ECC on Flash/SRAM let the chassis functions meet split-lock ASIL-D together with a second TC23x. The 2 MB Flash covers chassis signal processing firmware plus sensor calibration tables; CAN-FD moves real-time state to the central chassis domain controller over the standard vehicle bus. Compared with a low-end microcontroller, the AURIX adds deterministic DSP extension for active suspension math. Designers sometimes drop to TC233L or TC233P (smaller Flash) for simple sensor nodes. The TQFP-100 is appropriate for chassis-mounted PCBAs with exposed thermal pad for hot-floor testing.
推荐
Industrial / Robotics Functional-Safety PLC
Outside automotive, the SAK-TC233LP-32F200N supports industrial functional-safety controllers and small robotics PLCs that benefit from a deterministic 32-bit TriCore core and a TQFP-100 footprint, while keeping an automotive-grade ASIL-B story. The 2 MB Flash hosts IEC 61131-3 runtimes plus application logic for motor control, while CAN-FD and ASIL-B safety primitives help certify industrial machinery to IEC 61508 SIL-2/SIL-3. The AURIX safety library (SMU, Lockstep, ECC) is documented in the TC23xL User's Manual and aids CE machinery certification. Compared with a Cortex-R or Cortex-M microcontroller, the TriCore adds DSP extension for control-loop math. For high-end robotics nodes that need multi-axis control, designers usually move to TC26x or TC27x (dual/triple core).
推荐
DC Fast Charging / EV Charging Station Controller
The SAK-TC233LP-32F200N is suitable as a primary controller in DC fast charging station sub-modules where ISO 26262-derived safety CAN-FD communication, lockstep, and ECC are equally valuable in non-automotive settings. The single 200 MHz TriCore handles OCPP ↔ PLC ↔ power-module bridging, isolation monitoring, and authentication logic, while 2 MB Flash stores charging curves and remote firmware. The TC233LP family is widely deployed in modular EV charging controllers because of its deterministic interrupt response and 5 V-tolerant GPIOs that interface to industry-standard analog front ends. For higher-power 350 kW chargers with parallel modules, designers often twin two TC26x CPUs. The TQFP-100 footprint and Infineon toolchain shorten time to UL/IEC certification.
推荐
推荐产品汇总
工程参考数据： SAK-TC233LP-32F200N ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | SAK-TC233LP-32F200F | SAK-TC233L-32F200N | SAK-TC233SP-32F200N | SAK-TC234L-32F200N |
|---|---|---|---|---|---|
| Package | PG-TQFP-100-23 (100-pin TQFP, 14x14 mm) | PG-TQFP-100-23 - same | PG-TQFP-100-23 - same | PG-TQFP-100-23 - same | TQFP-100 (TC234L TQFP-100 footprint) |
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon |
| Maximum Clock Frequency | 200 MHz | 200 MHz | 200 MHz | 200 MHz | 200 MHz |
| Program Flash | 2 MB | 2 MB | 2 MB | 2 MB | 2 MB |
| Core Architecture | TriCore v1.6.1 (single-core, lockstep) | TriCore v1.6.1 (single-core) | TriCore v1.6.1 (single-core, no lockstep) | TriCore v1.6.1 (single-core, SP safety set) | TriCore v1.6.1 (TC234L, more peripherals) |
| CAN-FD Support | Yes (M_CAN, ISO 11898-1) | No (F-suffix drops CAN-FD) | Yes (M_CAN, ISO 11898-1) | Yes (M_CAN, ISO 11898-1) | Yes (M_CAN, ISO 11898-1) |
| Functional Safety (ISO 26262) | ASIL-B capable; split-lock ASIL-D on selected functions | ASIL-B capable; F variant reduces some safety functions | ASIL-B capable (no LP lockstep enhancement) | ASIL-B capable (different peripheral set) | ASIL-B / split-lock ASIL-D on TC234L peripherals |
| Lifecycle Status | active | active | active | active | active |
关键差异点
- Single-core AURIX TC23xL with built-in lockstep support （对比 SAK-TC233L-32F200N)
- CAN-FD / ISO 11898-1 support present on N-suffix （对比 SAK-TC233LP-32F200F)
- Lower peripheral count and lower cost than TC234L （对比 SAK-TC234L-32F200N)
设计说明
The SAK-TC233LP-32F200N has multiple supply rails (V_EXT for 5V/3.3V IO, V_EVR+/V_EVR- for the internal EVR switching stage, V_ADCx reference pins for the ADCs, V_BAT/V_RTC for RTC, and V_HSIF/V_FLEX for high-speed serial). Decouple each adjacent supply pin with at least 100 nF ceramic plus bulk 1 uF + 4.7 uF; the EVR driver return pin V_EVR- must be kelvined to the ground plane directly under the package to prevent switching noise from coupling into ADC references. V_SSEN must be tied in a star to V_SS at the package ground paddle.
The PG-TQFP-100-23 has an exposed thermal/ep pad (footprint name 23) which must be soldered to a continuous copper plane on the top layer. In automotive underhood environments, ambient of +125C and BCM current draw around 200-400 mA push junction temperature close to the 150C limit; a thermal copper pour of 1 square inch or more is needed. Use the Infineon AURIX TC23xL thermal model from the User's Manual to estimate theta_JA (~25 C/W with proper copper) and leave margin per ISO 16750 load-dump transients.
Estimated: assuming typical BCM task load at 200 MHz, the SAK-TC233LP-32F200N executes ~150-200 MIPS. Do NOT route the EVR switching currents through the digital ground; use the EVR ground plane per the Infineon AURIX TC2xx hardware design guide. When starting up, V_EXT must rise above the Power-On Reset threshold before any I/O toggles; otherwise the SMU will flag a cold-POR. Always connect V_BAT to a backup battery or supercap if you need RTC retention across cranking profiles.
Place 100 nF bypass capacitors within 1-2 mm of every V_EXT, V_EVR, V_ADC supply pin. The two V_EXT pins and multiple V_SS pins must be stitched with multiple vias into the same ground and power planes. The ADC analog ground (V_SSEN) and digital ground (V_SS) should be joined only at a single point near the chip. For CAN-FD and HSCT routing, observe the 50 ohm impedance for those pairs; for crystal traces (XIN/XOUT) keep the lines short, symmetric, and guarded by a ground ring to suppress spurious modes.
合规信息
AURIX TC2 family is positioned by Infineon for AEC-Q100 / ISO 26262 ASIL-B; AC suffix indicates automotive/automotive-traceable supply.
