SN74AC244N - 8-Channel 3-State Buffer | Texas Instruments
料号: SN74AC244N ✓ 量产中SN74AC244N 概述
A logic buffer or line driver is a digital integrated circuit that reproduces an input signal at an output while adding drive strength, isolation, or bus-management capability. The SN74AC244 belongs to the CMOS logic family and sits within the broader hierarchy of logic ICs, bus-interface ICs, and semiconductor components. Its three-state outputs allow multiple devices to share a data bus when their outputs are disabled, while the non-inverting architecture preserves the polarity of the input data.
Key features include eight buffered channels, a 2 V to 6 V operating supply range, and operation from -40 °C to 85 °C in the N-package ordering option. Each output can be placed in a high-impedance state through the device's output-enable controls, making it suitable for shared buses where multiple transmitters must not contend during inactive periods. The 20-pin PDIP package supports through-hole assembly and is available in tube packaging.
The SN74AC244 architecture separates eight input-to-output buffer channels from the bus-control logic. This arrangement supports propagation of address, control, and clock signals while providing stronger output drive than direct logic outputs. The high-impedance output state is particularly important when several buffer devices connect to the same bus; only the enabled device actively drives the shared conductors. Exact propagation-delay, output-current, and noise specifications should be selected from the manufacturer datasheet for the complete AC family.
Typical uses include three-state memory-address driver systems, clock-distribution networks, bidirectional or multi-source bus interface arrangements, and bus-oriented receiver and transmitter interfaces. The SN74AC244 can also serve as an output-isolation stage when a logic core must drive a shared peripheral bus without contending with another subsystem. Designers should verify the output-enable polarity and timing against the system control logic before integrating the device.
A key design consideration is ensuring that all devices connected to a shared bus agree on which output-enable state is active. Check the direction of the enable inputs and their timing relative to data changes so the bus is never released while two outputs actively drive it. Account for the additional propagation delay introduced by the buffer when establishing setup and hold timing at the receiving device.
This page organizes the manufacturer's operating limits, package information, verified drop-in alternatives, comparison data, and practical implementation guidance. It also highlights the distinction between the eight-channel buffered function, the three-state bus-management feature, and the 20-pin PDIP footprint that engineers must confirm before redesigning or replacing an existing assembly.
直接替换替代料: SN74AC244N ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
SN74AS244N
✅ 直接替换📋 参考替代料(不在目录中)
SN74AHC244N-P2
✅ 直接替换📋 参考替代料(不在目录中)
TC74AC244P
✅ 直接替换📋 参考替代料(不在目录中)
CD74AC244E
✅ 直接替换📋 参考替代料(不在目录中)
SN74AS244N
✅ 直接替换📋 参考替代料(不在目录中)
SN74AC244N 最大额定值与电气特性
| Number of Channels | 8 channels |
| Elements per Element | 4 bits |
| Logic Type | Non-inverting |
| Output State | 3-state |
| Supply Voltage Range | 2 V to 6 V |
| Number of Inputs | 8 inputs |
| 输出数量 | 8 outputs |
| Output Enable Control | 2 output-enable controls |
| Package Type | 20-pin PDIP |
| Total Pin Count | 20 pins |
| 安装类型 | Through-hole |
| 工作温度范围 | -40 °C to 85 °C |
SN74AC244N 引脚配置
| 引脚 1 | 1OE — Output enable for channels 1 through 4, active low |
| 引脚 2 | 1A — Data input for channel 1 |
| 引脚 3 | 1Y — Non-inverting output for channel 1 |
| 引脚 4 | 2A — Data input for channel 2 |
| 引脚 5 | 2Y — Non-inverting output for channel 2 |
| 引脚 6 | 3A — Data input for channel 3 |
| 引脚 7 | 3Y — Non-inverting output for channel 3 |
| 引脚 8 | GND — Ground reference |
| 引脚 9 | 4A — Data input for channel 4 |
| 引脚 10 | 4Y — Non-inverting output for channel 4 |
| 引脚 11 | 5A — Data input for channel 5 |
| 引脚 12 | 5Y — Non-inverting output for channel 5 |
| 引脚 13 | 6A — Data input for channel 6 |
| 引脚 14 | VCC — Positive supply voltage |
| 引脚 15 | 6Y — Non-inverting output for channel 6 |
| 引脚 16 | 7A — Data input for channel 7 |
| 引脚 17 | 7Y — Non-inverting output for channel 7 |
| 引脚 18 | 8A — Data input for channel 8 |
| 引脚 19 | 8Y — Non-inverting output for channel 8 |
| 引脚 20 | 2OE — Output enable for channels 5 through 8, active low |
典型应用
SN74AC244N 适用于 6 应用s: Three-State Memory Address Drivers, Clock Distribution Networks, Shared Bus Receivers and Transmitters, Data Bus Output Isolation, Industrial Control Signal Conditioning, Test and Measurement Interface Logic.
Three-State Memory Address Drivers
The SN74AC244N fits memory-address driver circuits because its eight channels can source or sink the buffered address signals while the three-state outputs provide controlled disconnection from a shared bus. The 2 V to 6 V supply range supports low-voltage logic systems, and the 20-pin PDIP package simplifies through-hole replacement. According to the Texas Instruments manufacturer datasheet, three-state memory-address drivers are an intended application. Designers should compare propagation delay and output-current limits for the intended memory load and preserve the active-low output-enable timing so that only the selected address driver asserts the bus.
推荐
Clock Distribution Networks
The SN74AC244N can distribute clock signals when the source is too weak to drive multiple loads or when clock routing requires buffering and isolation. Eight non-inverting channels permit separate clock domains, while the 3-state outputs can be disabled during selected bus intervals. The device operates from 2 V to 6 V and is specified for -40 °C to 85 °C in the N package. Because buffer delay is added to every clock path, use the manufacturer's timing curves to confirm setup and hold margins at the receiving logic. Output-enable transitions should remain controlled to avoid partial clock pulses or unintended bus contention.
推荐
Shared Bus Receivers and Transmitters
The SN74AC244N is appropriate for bus-oriented receiver and transmitter interfaces that require stronger drive or isolation between a logic core and shared conductors. Its eight non-inverting channels buffer the data path, and the three-state outputs allow unused devices to avoid loading the bus. The Texas Instruments manufacturer datasheet identifies bus-oriented receivers and transmitters as target applications. Keep only one output group enabled while another source drives the same bus unless the architecture guarantees no overlap. Verify the exact enable polarity, propagation delay, and drive current against the bus capacitance and the timing budget of the receiving endpoint.
推荐
Data Bus Output Isolation
The SN74AC244N can isolate a logic subsystem from a shared data bus by placing its outputs in the high-impedance state whenever that subsystem is not the active source. This prevents a weak internal output from fighting an external bus driver and improves signal integrity at higher fan-out. Its eight buffered channels cover eight parallel data lines, while the 2 V to 6 V operating range supports multiple logic voltages. The active-low output-enable inputs should be sequenced away from data transitions to prevent transient contention. For long traces or capacitive loads, compare the manufacturer's output-current curves and ringing behavior before finalizing the PCB topology.
推荐
Industrial Control Signal Conditioning
The SN74AC244N can buffer control and status signals in industrial electronics where a controller must interface with a remote logic bus through defined enable intervals. The eight-channel organization allows a compact implementation for byte-wide command or status paths, and the non-inverting behavior simplifies control-signal polarity. Its -40 °C to 85 °C N-package rating supports a broad range of industrial ambient conditions. The manufacturer datasheet identifies memory-address, clock, and bus-oriented signal applications. Engineers should still account for transient protection, grounding, and cable-length effects separately, because the logic buffer improves drive and isolation but does not replace overvoltage or surge-protection components.
推荐
Test and Measurement Interface Logic
The SN74AC244N is useful in test and measurement equipment when front-panel control bits, status flags, or instrument-bus signals require buffering before reaching a processor or remote interface. Its eight channels and three-state outputs support grouped isolation, allowing unselected interface sections to remain electrically detached. The 2 V to 6 V supply range provides compatibility with common low-voltage control logic, and the 20-pin PDIP package supports conventional through-hole construction. Timing must be checked against the acquisition or control system, especially when the same output bus is shared by multiple instrument functions. Use a single documented enable-control policy to prevent simultaneous activation and data corruption.
推荐
推荐产品汇总
工程参考数据: SN74AC244N ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | SN74AS244N | SN74AHC244N-P2 | TC74AC244P | CD74AC244E | SN74AS244N |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Toshiba | Texas Instruments | Texas Instruments |
| Package | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP |
| Channel Count | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Output State | 3-state | 3-state | 3-state | 3-state | 3-state | 3-state |
| Logic Polarity | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting |
关键差异点
- Wide low-voltage operating range in a standard through-hole package (对比 SN74AS244N)
- Explicit eight-channel three-state bus-buffer function (对比 TC74AC244P)
- Direct fit for systems designed around the AC-family footprint (对比 CD74AC244E)
设计说明
Treat the two active-low output-enable groups as shared-bus ownership controls. Disable the outgoing buffer before enabling another device, and allow a dead interval between enable changes. This prevents two outputs from driving different levels onto the same node at the same time. Check receiver setup and hold timing using the combined propagation delay of the source buffer, interconnect, and destination logic rather than relying only on nominal clock frequency.
Place the SN74AC244N close to the memory, clock, or bus-interface circuitry that it buffers, especially when traces are long or capacitive. Keep output-enable routing away from high-current switching nodes to reduce coupling into the control inputs. For the 20-pin PDIP implementation, provide adequate clearance around adjacent pins and maintain a low-impedance ground return. If high-speed or heavily capacitive buses are involved, add source termination or series damping only after evaluating the complete signal path.
Do not assume that every octal-buffer cross reference is electrically interchangeable. The SN74AC244N has eight non-inverting 3-state channels, two active-low output-enable controls, a 2 V to 6 V supply range, and a 20-pin PDIP footprint. Before substituting SN74AS244N, SN74AHC244N-P2, TC74AC244P, or CD74AC244E, verify supply voltage, enable polarity, propagation delay, output drive, input thresholds, and temperature limits in the relevant manufacturer documentation.
合规信息
Compliance attributes require confirmation from the manufacturer product page, current declarations, or the complete manufacturer datasheet.