MaxLinear

SP3232EBCT-L - 2/2 RS-232 Transceiver, 3-5.5V | MaxLinear (Tape & Reel)

料号: SP3232EBCT-L ✓ 量产中
+3.0 V to +5.5 V Vdss 1 uA with receivers active on SP3222EB Id 16-SOIC Package
最小起订量: 1 |

SP3232EBCT-L 概述

MaxLinear SP3232EBCT-L is a dual line RS-232 transceiver with two drivers and two receivers, operating from a single +3.0 V to +5.5 V supply and packaged in a 16-pin SOIC. It supports transmission rates up to 250 kbps under load and is designed for portable and hand-held equipment requiring a complete bidirectional RS-232 interface.

An RS-232 transceiver is a physical-layer interface IC that converts between digital logic levels and the voltage-defined RS-232 interface used for serial communications. The SP3232EB family combines two transmit channels, two receive channels, on-chip level translation, and a charge-pump voltage source for the bipolar RS-232 signal. This places it in the hierarchy of interface ICs, transceiver ICs, serial-interface ICs, and semiconductor devices.

The SP3232EBCT-L operates from +3.0 V to +5.5 V and can therefore be powered from common 3.3 V or 5 V system rails. Its stated 250 kbps transmission rate under load is suitable for moderate-speed data links, configuration interfaces, instrumentation, and embedded control links. The 16-SOIC package allows direct use of a familiar surface-mount footprint and simplifies assembly where a larger quad-channel RS-232 device is unnecessary.

The internal charge-pump supply generates the positive and negative voltages required by true RS-232 drivers. According to the MaxLinear product page, the SP3222EB/SP3232EB series uses only 0.1 uF charge-pump capacitors in 3.3 V operation. A dual-channel architecture can also reduce the number of external interface ICs compared with a quad transceiver, although signal-routing and channel-count requirements still determine the final choice.

Typical applications include portable data terminals, hand-held test equipment, industrial control modules, point-of-sale equipment, and embedded serial adapters. The integrated level translation allows a low-voltage controller to communicate with a conventional RS-232 host while keeping the external power-supply design relatively simple.

Designers should follow the manufacturer’s recommended charge-pump capacitor values, place them close to the associated pins, and observe the external capacitor requirements of the transmitter and receiver network. PCB layout should keep the RS-232 connector and interface traces away from sensitive analog or high-speed digital paths. The maximum cable length, termination, grounding, and protection arrangement should be selected for the intended communication standard and operating environment.

This product summary combines the manufacturer family specifications with practical application, package, and replacement guidance. It also highlights the distinctions that matter when evaluating the SP3232EBCT-L against other dual RS-232 transceivers.

直接替换替代料: SP3232EBCT-L ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: SP3232EBCT-L (相同外形与封装尺寸) ——差异在于 Package, Operating Temperature, Product Type, Supply Voltage Range, Maximum Data Rate.

MaxLinear
Supply Voltage Range: 3 V to 5.5 V
MaxLinear
Package: 16-pin SOIC
Operating Temperature: -40°C to +85°C
Maximum Data Rate: 120 kbps
MaxLinear
Operating Temperature: -40 C to +85 C
Product Type: RS-232 transceiver
MaxLinear
Package: 16-pin TSSOP
Operating Temperature: -40 °C to +85 °C
Product Type: RS-232 transceiver

SP3232EEN-L/TR

✅ 直接替换
MaxLinear
📦 16-SOIC
2/2 transceiver, full RS-232 · 2 · 2 · 120 kbps · 3 V to 5.5 V · 1 mA · 1 µA · -40°C to +85°C

联系询价

查看数据手册 →

SP3232EEY-L/TR

✅ 直接替换
MaxLinear
📦 16-SOIC
RS-232 transceiver · 2 · 2 · 120 kbps under full load · 3.0 V to 5.5 V · 1 mA · True EIA/TIA-232-F operation · 0.1 µF

联系询价

查看数据手册 →

SP3232ECT-L/TR

✅ 直接替换 ⚠️ 规格未核验
MaxLinear
📦 16-SOIC
2/2 RS-232 transceiver · 2 · 2 · 3 V to 5.5 V · 120 kbit/s · True EIA/TIA-232-F · 1 µA · 0.1 µF

联系询价

查看数据手册 →

SP3232EET-L/TR

✅ 直接替换 ⚠️ 规格未核验
MaxLinear
📦 16-SOIC
RS-232 transceiver · 2 transmit / 2 receive channels · +3.0 V to +5.5 V · 120 kbps · 1 mA · -40 C to +85 C · 16-SOIC · RS-232 / EIA/TIA-232-F

联系询价

查看数据手册 →

ST3232ECWR

✅ 直接替换
📦 16-SOIC
Cross-brand 2/2 RS-232 transceiver with a 16-SOIC footprint; receive-fail-safe behavior and detailed electrical limits require comparison

📋 参考替代料(不在目录中)

SP3232EBCT-L 规格参数

Product Type 2/2 RS-232 transceiver
Number of Drivers 2
Number of Receivers 2
Supply Voltage Range +3.0 V to +5.5 V
Maximum Transmission Rate 250 kbps under load
Protocol RS-232
Compliance Standard EIA/TIA-232-F
ESD Protection, Human Body Model +15 kV
ESD Protection, IEC 61000-4-2 Air Discharge +15 kV
ESD Protection, IEC 61000-4-2 Contact Discharge +8 kV
Charge-Pump Capacitor Value at 3.3 V 0.1 uF
封装 16-SOIC
Package Body Width 7.50 mm
Packaging Tube
安装类型 Surface mount
Low-Power Shutdown Current 1 uA with receivers active on SP3222EB
Interoperability Supply Lower Limit +2.7 V

SP3232EBCT-L 7.50 mm 引脚配置指南

SP3232EBCT-L(7.50 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

SP3232EBCT-L 的 7.50 mm 封装引脚图

暂无详细引脚数据: SP3232EBCT-L.

请参阅 数据手册 以查看完整引脚配置。

典型应用

SP3232EBCT-L 适用于 6 应用s: Portable RS-232 Data Terminals, Industrial Control Modules, Point-of-Sale Equipment, Instrumentation and Test Equipment, Embedded Serial Adapters, Networking and Communications Equipment.

📱

Portable RS-232 Data Terminals

The SP3232EBCT-L fits portable and hand-held equipment that needs two RS-232 communication channels without a separate level translator. Its +3.0 V to +5.5 V operating range allows use with a 3.3 V system rail, while the 250 kbps under-load rate covers common configuration and control links. The two-driver, two-receiver arrangement reduces the number of interface ICs compared with a quad-channel device. A practical implementation places the transceiver beside the connector, follows the manufacturer’s 0.1 uF charge-pump capacitor guidance for 3.3 V operation, and routes the RS-232 traces away from sensitive circuitry.

🏭

Industrial Control Modules

The SP3232EBCT-L is appropriate for industrial modules that exchange commands or status data with an RS-232 master. Two drivers and two receivers support two logical links while the single +3.0 V to +5.5 V supply simplifies integration with 3.3 V or 5 V control electronics. The 250 kbps maximum rate is suitable for moderate-speed supervisory traffic rather than high-bandwidth protocols. Industrial implementations should add appropriate connector-side protection and verify grounding, cable length, and noise margins under the expected electromagnetic environment.

🖥️

Point-of-Sale Equipment

The SP3232EBCT-L can provide two RS-232 channels for peripherals such as a receipt printer, scanner, customer display, or weighing interface. Its two transmit and two receive paths give the equipment designer more flexibility than a single-channel transceiver while retaining a compact 16-SOIC footprint. The device operates directly from +3.0 V to +5.5 V, and the 250 kbps under-load rating is appropriate for transactional serial traffic. Follow the manufacturer capacitor and grounding guidance, and place external protection where cables can be exposed to user-accessible connectors.

🔧

Instrumentation and Test Equipment

The SP3232EBCT-L is useful in portable and bench instrumentation that communicates with legacy RS-232 test equipment. Its two bidirectional interface paths can support a control channel and a status or measurement channel, while the low-voltage supply operation reduces the number of power rails required by the instrument. The 250 kbps under-load capability is suitable for command and data-transfer functions that do not require continuous high-rate streaming. Validate the complete channel with the intended cable and instrument because capacitance, grounding, and driver loading can affect the usable distance.

🧩

Embedded Serial Adapters

The SP3232EBCT-L is well suited to small adapters that bridge a modern low-voltage controller to two conventional RS-232 ports. Its single-supply range of +3.0 V to +5.5 V allows the adapter to operate from 3.3 V or 5 V logic rails, and the integrated charge pump removes the need for a separate bipolar RS-232 supply. The 16-SOIC package supports compact assembly. Designers should follow the exact charge-pump capacitor connections, include the required interface-network components, and provide connector-side protection if the adapter will be field-installed.

🌐

Networking and Communications Equipment

The SP3232EBCT-L can support low-speed management or service interfaces on communications equipment that retains an RS-232 port. Two transmit and two receive channels allow concurrent command and diagnostic functions, while the 250 kbps under-load rating fits supervisory protocols. Its 3.0 V to 5.5 V operation is useful in systems using mixed digital rails. In network equipment, maintain a defined grounding strategy, keep transceiver charge-pump loops compact, and verify EMC and ESD performance at the external connector rather than assuming on-chip ratings eliminate the need for system protection.

推荐产品汇总

What is the SP3232EBCT-L?
The SP3232EBCT-L is a dual-line RS-232 transceiver with two drivers and two receivers, a +3.0 V to +5.5 V supply range, and a 16-SOIC package. According to the MaxLinear SP3232EB product page, the device is part of the SP3222EB/SP3232EB family for portable and hand-held equipment and provides true RS-232 operation from a single low-voltage supply.
What is the operating voltage of SP3232EBCT-L?
The SP3232EBCT-L operates from +3.0 V to +5.5 V. The MaxLinear SP3232EB product information states that the SP3222EB/SP3232EB family works from a single +3.0 V to +5.5 V power supply and remains interoperable with RS-232 down to +2.7 V. This allows operation from common 3.3 V and 5 V digital rails.
What are the key specifications of SP3232EBCT-L that engineers should know?
The principal specifications are two RS-232 drivers, two receivers, a +3.0 V to +5.5 V supply range, and a maximum data rate of 250 kbps under load. The device also uses a 16-SOIC package and its family includes enhanced ESD ratings of +15 kV for the human body model and IEC 61000-4-2 air discharge, plus +8 kV for contact discharge.
Where can I download the SP3232EBCT-L datasheet PDF?
The manufacturer documentation for the SP3232EB family is available through the official MaxLinear product page linked on this page. Open the SP3232EB product listing and select its datasheet resources. The 16-pin ordering information, electrical characteristics, charge-pump capacitor requirements, ESD limits, and package dimensions should be checked against the exact SP3232EBCT-L ordering code before release.
Where can I find the SP3232EBCT-L pinout?
Use the pin-description table in the manufacturer SP3232EB datasheet to identify the driver inputs, receiver outputs, supply pins, charge-pump capacitor connections, and ground connections for the 16-SOIC package. The device is a 16-pin SOIC, but the online product listing does not reproduce every terminal number, so the package drawing should be cross-checked before assigning PCB tracks.
Is SP3232EBCT-L suitable for a 3.3 V RS-232 port?
Yes, the SP3232EBCT-L is suitable for a 3.3 V RS-232 port because its stated supply range is +3.0 V to +5.5 V. According to the MaxLinear product page, the SP3222EB/SP3232EB family requires only 0.1 uF charge-pump capacitors in 3.3 V operation. The external transceiver network and logic levels must still match the system interface.
How fast can SP3232EBCT-L transmit RS-232 data?
The SP3232EBCT-L supports transmission rates up to 250 kbps under load. That rate is appropriate for many embedded control, configuration, instrumentation, and point-of-sale links. Cable length, capacitive loading, logic levels, and the connected equipment can reduce practical performance, so validate the complete channel rather than relying only on the rated data rate.
What ESD protection does SP3232EBCT-L provide?
The SP3232EB family provides enhanced ESD protection of +15 kV for the human body model, +15 kV for IEC 61000-4-2 air discharge, and +8 kV for IEC 61000-4-2 contact discharge. These figures describe the device’s specified ESD capability. A complete exposed connector path may still require external surge and ESD protection.
Can SP3232EEN-L/TR replace SP3232EBCT-L?
SP3232EEN-L/TR is a pin-compatible candidate in the SP3232EB family, but final substitution requires comparing its ordering suffix, temperature grade, and package drawing against SP3232EBCT-L. The manufacturer documentation should be used to verify supply range, channel count, data rate, ESD ratings, and capacitor requirements. Do not rely on the family name alone for a production release.
Can ST3232ECWR replace SP3232EBCT-L?
ST3232ECWR can be considered as a cross-brand replacement candidate because it is identified as a 2/2 RS-232 transceiver in a 16-SOIC package. Pin functions, supply range, data rate, receiver fail-safe behavior, and charge-pump component requirements must still be checked against the SP3232EBCT-L datasheet. Confirm every connection and performance limit before substitution.
What is the best Exar equivalent for SP3232EBCT-L?
SP3232EEN-L/TR and SP3232EEY-L/TR are the closest documented Exar-family candidates for a replacement review because they belong to the SP3232EB line and are presented as direct comparisons with SP3232EBCT-L. Their suffix-specific package, temperature range, and electrical details must be checked before approval, since related family members can differ in grade or qualification.
When should I choose SP3232EBCT-L over a quad RS-232 transceiver?
Choose SP3232EBCT-L when the design needs exactly two transmit channels and two receive channels and benefits from a smaller channel count. A quad transceiver is more appropriate when four driver and four receiver channels are required and its additional functions or ratings are otherwise useful. Reducing channel count can simplify routing, but the selected device must still meet all required RS-232 and ESD specifications.
Is SP3232EBCT-L the same as SP3232EEN-L/TR?
No, SP3232EBCT-L and SP3232EEN-L/TR are related family members but are not necessarily identical ordering codes. The target is the SP3232EBCT-L in a 16-SOIC package, while the suffix may indicate a different package or temperature grade. Compare the manufacturer ordering table, pinout, operating-temperature range, and production-grade requirements before treating them as interchangeable.
Where can I buy SP3232EBCT-L online?
Use the Request a Quote form on this page to request the SP3232EBCT-L, current commercial terms, quantity availability, and expected lead time. The structured listings on this page contain technical and sourcing information, while the quote form is the channel for a current order response. Buyers should specify the tube or reel packaging required for their assembly process.
What is the price of SP3232EBCT-L?
The current price for SP3232EBCT-L should be obtained through the Request a Quote form on this page. Pricing can vary with quantity, package form, order configuration, and market conditions, and no static figure should be used for purchasing decisions. Include the required production quantity and packaging preference with the request.
What is the lead time and stock status for SP3232EBCT-L?
Current stock status and lead time for SP3232EBCT-L should be requested through the Request a Quote form on this page. Provide the required quantity, target delivery date, and whether the assembly line uses tube or reel packaging. The Request a Quote response is the appropriate source for a production commitment rather than a generic availability claim.

工程参考数据: SP3232EBCT-L ——对比、设计指导和合规信息。

选型指南

Choose SP3232EBCT-L for a compact, 16-SOIC design that needs two RS-232 drivers and two receivers from a +3.0 V to +5.5 V supply, particularly when a 3.3 V rail and up to 250 kbps under load are required. SP3232EEN-L/TR and SP3232EEY-L/TR are strong same-family candidates for replacement review, but their suffix-specific package and temperature details must be confirmed. SP3232ECT-L/TR and SP3232EET-L/TR are additional Exar-family options whose exact production ratings should be verified. ST3232ECWR is useful as a cross-brand candidate, but its receiver fail-safe behavior and electrical limits require a full comparison. A quad transceiver is preferable when four transmit and four receive channels are required. In every case, validate the complete interface against the required EIA/TIA-232-F performance, cable environment, and connector-protection plan.

与替代料对比

参数 本产品 SP3232EEN-L/TR SP3232EEY-L/TR SP3232ECT-L/TR SP3232EET-L/TR ST3232ECWR
Package 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC
Brand MaxLinear Exar Corporation Exar Corporation Exar Corporation Exar Corporation STMicroelectronics
Transceiver Configuration 2/2 2/2 SP3232EB family 2/2 SP3232EB family 2/2 SP3232EB family 2/2 SP3232EB family 2/2

关键差异点

  • Two full-duplex RS-232 channels in one 16-SOIC device (对比 ST3232ECWR)
  • Operation from a single +3.0 V to +5.5 V supply (对比 SP3232EEN-L/TR)
  • Specified 250 kbps transmission rate under load (对比 SP3232EEY-L/TR)
  • Enhanced system-facing ESD ratings (对比 SP3232ECT-L/TR)

设计说明

Place the charge-pump capacitors close to their designated SP3232EBCT-L pins and use the capacitance and tolerance specified by the manufacturer for the selected supply voltage. Keep the high-current charge-pump loop compact to reduce radiated and conducted emissions. Place the interface components near the associated driver or receiver pins, and route connector-side protection components directly to the appropriate ground reference.

Do not substitute a related SP3232EB ordering code solely because the family name matches. Confirm the package drawing, pin functions, temperature grade, supply limits, data rate, and ESD ratings for every suffix. In particular, an apparently equivalent 16-SOIC transceiver can differ in receiver fail-safe behavior or operating-temperature limits, so a production substitution requires a complete electrical comparison.

Keep the RS-232 connector and cable entry away from sensitive analog sections and high-speed digital clocks. Provide a solid ground reference, route the interface as a differential-ish bipolar pair according to the system’s grounding strategy, and avoid long unprotected stubs. If the port is user-accessible, use external protection because the device’s specified ESD capability does not eliminate connector-side system requirements.

Separate the charge-pump area from precision measurement circuits and place input, receiver, and charge-pump decoupling according to the manufacturer layout guidance. Avoid connecting transient or surge current directly through the logic ground path. For compact boards, verify the 16-SOIC body width of 7.50 mm and the complete land pattern, including lead pitch and solder mask clearance, before releasing artwork.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The family documentation references EIA/TIA-232-F and IEC 61000-4-2 ESD test levels. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not confirmed for this exact ordering code.

相关搜索

SP3232EBCT-L SP3232EBCT-L datasheet SP3232EBCT-L datasheet pdf SP3232EBCT-L pinout SP3232EBCT-L equivalent SP3232EBCT-L replacement SP3232EBCT-L cross reference SP3232EBCT-L vs ST3232ECWR SP3232EBCT-L 16-SOIC footprint MaxLinear SP3232EBCT-L SP3232EBCT-L 3.3V RS-232 SP3232EBCT-L 250kbps SP3232EBCT-L price SP3232EBCT-L stock SP3232EBCT-L application circuit

相关元器件 & 术语

MaxLinear Exar Corporation STMicroelectronics SP3232EBCT-L SP3232EEN-L/TR SP3232EEY-L/TR SP3232ECT-L/TR SP3232EET-L/TR ST3232ECWR RS-232 transceiver interface IC transceiver IC serial-interface IC semiconductor EIA/TIA-232-F IEC 61000-4-2 RoHS REACH 16-SOIC SOIC family surface-mount package charge-pump voltage supply 250 kbps transmission rate +3.0 V to +5.5 V supply ESD protection
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情